board/myir/mys_6ulx/spl.c

   1 // SPDX-License-Identifier: GPL-2.0+
   2 /*
   3  * Copyright (C) 2020 Linumiz
   4  * Author: Parthiban Nallathambi <parthiban@linumiz.com>
   5  */
   6
   7 #include <common.h>
   8 #include <init.h>
   9 #include <spl.h>
  10 #include <asm/arch/clock.h>
  11 #include <asm/io.h>
  12 #include <asm/arch/mx6-ddr.h>
  13 #include <asm/arch/mx6-pins.h>
  14 #include <asm/arch/crm_regs.h>
  15 #include <asm/arch/sys_proto.h>
  16 #include <fsl_esdhc_imx.h>
  17
  18 /* Configuration for Micron MT41K128M16JT-125, 32M x 16 x 8 -> 256MiB */
  19
  20 static struct mx6ul_iomux_grp_regs mx6_grp_ioregs = {
  21         .grp_addds = 0x00000030,
  22         .grp_ddrmode_ctl = 0x00020000,
  23         .grp_b0ds = 0x00000030,
  24         .grp_ctlds = 0x00000030,
  25         .grp_b1ds = 0x00000030,
  26         .grp_ddrpke = 0x00000000,
  27         .grp_ddrmode = 0x00020000,
  28         .grp_ddr_type = 0x000c0000,
  29 };
  30
  31 static struct mx6ul_iomux_ddr_regs mx6_ddr_ioregs = {
  32         .dram_dqm0 = 0x00000030,
  33         .dram_dqm1 = 0x00000030,
  34         .dram_ras = 0x00000030,
  35         .dram_cas = 0x00000030,
  36         .dram_odt0 = 0x00000030,
  37         .dram_odt1 = 0x00000030,
  38         .dram_sdba2 = 0x00000000,
  39         .dram_sdclk_0 = 0x00000030,
  40         .dram_sdqs0 = 0x00000030,
  41         .dram_sdqs1 = 0x00000030,
  42         .dram_reset = 0x00000030,
  43 };
  44
  45 static struct mx6_mmdc_calibration mx6_mmcd_calib = {
  46         .p0_mpwldectrl0 = 0x00000000,
  47         .p0_mpdgctrl0 = 0x41480148,
  48         .p0_mprddlctl = 0x40403E42,
  49         .p0_mpwrdlctl = 0x40405852,
  50 };
  51
  52 struct mx6_ddr_sysinfo ddr_sysinfo = {
  53         .dsize = 0,             /* Bus size = 16bit */
  54         .cs_density = 32,
  55         .ncs = 1,
  56         .cs1_mirror = 0,
  57         .rtt_wr = 1,
  58         .rtt_nom = 1,
  59         .walat = 1,             /* Write additional latency */
  60         .ralat = 5,             /* Read additional latency */
  61         .mif3_mode = 3,         /* Command prediction working mode */
  62         .bi_on = 1,             /* Bank interleaving enabled */
  63         .pd_fast_exit = 1,
  64         .sde_to_rst = 0x10,     /* 14 cycles, 200us (JEDEC default) */
  65         .rst_to_cke = 0x23,     /* 33 cycles, 500us (JEDEC default) */
  66         .ddr_type = DDR_TYPE_DDR3,
  67         .refsel = 1,            /* Refresh cycles at 32KHz */
  68         .refr = 7,              /* 8 refresh commands per refresh cycle */
  69 };
  70
  71 /* MT41K128M16JT-125 (2Gb density) */
  72 static struct mx6_ddr3_cfg mem_ddr = {
  73         .mem_speed = 1600,
  74         .density = 2,
  75         .width = 16,
  76         .banks = 8,
  77         .rowaddr = 14,
  78         .coladdr = 10,
  79         .pagesz = 2,
  80         .trcd = 1375,
  81         .trcmin = 4875,
  82         .trasmin = 3500,
  83 };
  84
  85 static void ccgr_init(void)
  86 {
  87         struct mxc_ccm_reg *ccm = (struct mxc_ccm_reg *)CCM_BASE_ADDR;
  88
  89         writel(0xFFFFFFFF, &ccm->CCGR0);
  90         writel(0xFFFFFFFF, &ccm->CCGR1);
  91         writel(0xFFFFFFFF, &ccm->CCGR2);
  92         writel(0xFFFFFFFF, &ccm->CCGR3);
  93         writel(0xFFFFFFFF, &ccm->CCGR4);
  94         writel(0xFFFFFFFF, &ccm->CCGR5);
  95         writel(0xFFFFFFFF, &ccm->CCGR6);
  96 }
  97
  98 static void spl_dram_init(void)
  99 {
 100         mx6ul_dram_iocfg(mem_ddr.width, &mx6_ddr_ioregs, &mx6_grp_ioregs);
 101         mx6_dram_cfg(&ddr_sysinfo, &mx6_mmcd_calib, &mem_ddr);
 102 }
 103
 104 #ifdef CONFIG_FSL_ESDHC_IMX
 105
 106 #define USDHC_PAD_CTRL (PAD_CTL_PKE         | PAD_CTL_PUE       | \
 107                         PAD_CTL_PUS_22K_UP  | PAD_CTL_SPEED_LOW | \
 108                         PAD_CTL_DSE_80ohm   | PAD_CTL_SRE_FAST  | \
 109                         PAD_CTL_HYS)
 110
 111 static iomux_v3_cfg_t const usdhc1_pads[] = {
 112         MX6_PAD_SD1_CLK__USDHC1_CLK | MUX_PAD_CTRL(USDHC_PAD_CTRL),
 113         MX6_PAD_SD1_CMD__USDHC1_CMD | MUX_PAD_CTRL(USDHC_PAD_CTRL),
 114         MX6_PAD_SD1_DATA0__USDHC1_DATA0 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
 115         MX6_PAD_SD1_DATA1__USDHC1_DATA1 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
 116         MX6_PAD_SD1_DATA2__USDHC1_DATA2 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
 117         MX6_PAD_SD1_DATA3__USDHC1_DATA3 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
 118         MX6_PAD_UART1_RTS_B__USDHC1_CD_B | MUX_PAD_CTRL(USDHC_PAD_CTRL),
 119 };
 120
 121 #ifndef CONFIG_NAND_MXS
 122 static iomux_v3_cfg_t const usdhc2_pads[] = {
 123         MX6_PAD_NAND_RE_B__USDHC2_CLK    | MUX_PAD_CTRL(USDHC_PAD_CTRL),
 124         MX6_PAD_NAND_WE_B__USDHC2_CMD    | MUX_PAD_CTRL(USDHC_PAD_CTRL),
 125         MX6_PAD_NAND_DATA00__USDHC2_DATA0 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
 126         MX6_PAD_NAND_DATA01__USDHC2_DATA1 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
 127         MX6_PAD_NAND_DATA02__USDHC2_DATA2 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
 128         MX6_PAD_NAND_DATA03__USDHC2_DATA3 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
 129         MX6_PAD_NAND_DATA04__USDHC2_DATA4 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
 130         MX6_PAD_NAND_DATA05__USDHC2_DATA5 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
 131         MX6_PAD_NAND_DATA06__USDHC2_DATA6 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
 132         MX6_PAD_NAND_DATA07__USDHC2_DATA7 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
 133 };
 134 #endif
 135
 136 static struct fsl_esdhc_cfg usdhc_cfg[] = {
 137         {
 138                 .esdhc_base = USDHC1_BASE_ADDR,
 139                 .max_bus_width = 4,
 140         },
 141 #ifndef CONFIG_NAND_MXS
 142         {
 143                 .esdhc_base = USDHC2_BASE_ADDR,
 144                 .max_bus_width = 8,
 145         },
 146 #endif
 147 };
 148
 149 int board_mmc_getcd(struct mmc *mmc)
 150 {
 151         return 1;
 152 }
 153
 154 int board_mmc_init(struct bd_info *bis)
 155 {
 156         int i, ret;
 157
 158         for (i = 0; i < CFG_SYS_FSL_USDHC_NUM; i++) {
 159                 switch (i) {
 160                 case 0:
 161                         SETUP_IOMUX_PADS(usdhc1_pads);
 162                         usdhc_cfg[i].sdhc_clk = mxc_get_clock(MXC_ESDHC_CLK);
 163                         break;
 164 #ifndef CONFIG_NAND_MXS
 165                 case 1:
 166                         SETUP_IOMUX_PADS(usdhc2_pads);
 167                         usdhc_cfg[i].sdhc_clk = mxc_get_clock(MXC_ESDHC_CLK);
 168                         break;
 169 #endif
 170                 default:
 171                         printf("Warning - USDHC%d controller not supporting\n",
 172                                i + 1);
 173                         return 0;
 174                 }
 175
 176                 ret = fsl_esdhc_initialize(bis, &usdhc_cfg[i]);
 177                 if (ret) {
 178                         printf("Warning: failed to initialize mmc dev %d\n", i);
 179                         return ret;
 180                 }
 181         }
 182
 183         return 0;
 184 }
 185
 186 #endif /* CONFIG_FSL_ESDHC_IMX */
 187
 188 void board_init_f(ulong dummy)
 189 {
 190         ccgr_init();
 191
 192         /* Setup AIPS and disable watchdog */
 193         arch_cpu_init();
 194
 195         /* Setup iomux and fec */
 196         board_early_init_f();
 197
 198         /* Setup GP timer */
 199         timer_init();
 200
 201         /* UART clocks enabled and gd valid - init serial console */
 202         preloader_console_init();
 203
 204         /* DDR initialization */
 205         spl_dram_init();
 206 }