2 # (C) Copyright 2000 - 2013
3 # Wolfgang Denk, DENX Software Engineering, wd@denx.de.
5 # SPDX-License-Identifier: GPL-2.0+
11 This directory contains the source code for U-Boot, a boot loader for
12 Embedded boards based on PowerPC, ARM, MIPS and several other
13 processors, which can be installed in a boot ROM and used to
14 initialize and test the hardware or to download and run application
17 The development of U-Boot is closely related to Linux: some parts of
18 the source code originate in the Linux source tree, we have some
19 header files in common, and special provision has been made to
20 support booting of Linux images.
22 Some attention has been paid to make this software easily
23 configurable and extendable. For instance, all monitor commands are
24 implemented with the same call interface, so that it's very easy to
25 add new commands. Also, instead of permanently adding rarely used
26 code (for instance hardware test utilities) to the monitor, you can
27 load and run it dynamically.
33 In general, all boards for which a configuration option exists in the
34 Makefile have been tested to some extent and can be considered
35 "working". In fact, many of them are used in production systems.
37 In case of problems see the CHANGELOG and CREDITS files to find out
38 who contributed the specific port. The boards.cfg file lists board
41 Note: There is no CHANGELOG file in the actual U-Boot source tree;
42 it can be created dynamically from the Git log using:
50 In case you have questions about, problems with or contributions for
51 U-Boot you should send a message to the U-Boot mailing list at
52 <u-boot@lists.denx.de>. There is also an archive of previous traffic
53 on the mailing list - please search the archive before asking FAQ's.
54 Please see http://lists.denx.de/pipermail/u-boot and
55 http://dir.gmane.org/gmane.comp.boot-loaders.u-boot
58 Where to get source code:
59 =========================
61 The U-Boot source code is maintained in the git repository at
62 git://www.denx.de/git/u-boot.git ; you can browse it online at
63 http://www.denx.de/cgi-bin/gitweb.cgi?p=u-boot.git;a=summary
65 The "snapshot" links on this page allow you to download tarballs of
66 any version you might be interested in. Official releases are also
67 available for FTP download from the ftp://ftp.denx.de/pub/u-boot/
70 Pre-built (and tested) images are available from
71 ftp://ftp.denx.de/pub/u-boot/images/
77 - start from 8xxrom sources
78 - create PPCBoot project (http://sourceforge.net/projects/ppcboot)
80 - make it easier to add custom boards
81 - make it possible to add other [PowerPC] CPUs
82 - extend functions, especially:
83 * Provide extended interface to Linux boot loader
86 * PCMCIA / CompactFlash / ATA disk / SCSI ... boot
87 - create ARMBoot project (http://sourceforge.net/projects/armboot)
88 - add other CPU families (starting with ARM)
89 - create U-Boot project (http://sourceforge.net/projects/u-boot)
90 - current project page: see http://www.denx.de/wiki/U-Boot
96 The "official" name of this project is "Das U-Boot". The spelling
97 "U-Boot" shall be used in all written text (documentation, comments
98 in source files etc.). Example:
100 This is the README file for the U-Boot project.
102 File names etc. shall be based on the string "u-boot". Examples:
104 include/asm-ppc/u-boot.h
106 #include <asm/u-boot.h>
108 Variable names, preprocessor constants etc. shall be either based on
109 the string "u_boot" or on "U_BOOT". Example:
111 U_BOOT_VERSION u_boot_logo
112 IH_OS_U_BOOT u_boot_hush_start
118 Starting with the release in October 2008, the names of the releases
119 were changed from numerical release numbers without deeper meaning
120 into a time stamp based numbering. Regular releases are identified by
121 names consisting of the calendar year and month of the release date.
122 Additional fields (if present) indicate release candidates or bug fix
123 releases in "stable" maintenance trees.
126 U-Boot v2009.11 - Release November 2009
127 U-Boot v2009.11.1 - Release 1 in version November 2009 stable tree
128 U-Boot v2010.09-rc1 - Release candiate 1 for September 2010 release
134 /arch Architecture specific files
135 /arc Files generic to ARC architecture
136 /cpu CPU specific files
137 /arc700 Files specific to ARC 700 CPUs
138 /lib Architecture specific library files
139 /arm Files generic to ARM architecture
140 /cpu CPU specific files
141 /arm720t Files specific to ARM 720 CPUs
142 /arm920t Files specific to ARM 920 CPUs
143 /at91 Files specific to Atmel AT91RM9200 CPU
144 /imx Files specific to Freescale MC9328 i.MX CPUs
145 /s3c24x0 Files specific to Samsung S3C24X0 CPUs
146 /arm926ejs Files specific to ARM 926 CPUs
147 /arm1136 Files specific to ARM 1136 CPUs
148 /pxa Files specific to Intel XScale PXA CPUs
149 /sa1100 Files specific to Intel StrongARM SA1100 CPUs
150 /lib Architecture specific library files
151 /avr32 Files generic to AVR32 architecture
152 /cpu CPU specific files
153 /lib Architecture specific library files
154 /blackfin Files generic to Analog Devices Blackfin architecture
155 /cpu CPU specific files
156 /lib Architecture specific library files
157 /m68k Files generic to m68k architecture
158 /cpu CPU specific files
159 /mcf52x2 Files specific to Freescale ColdFire MCF52x2 CPUs
160 /mcf5227x Files specific to Freescale ColdFire MCF5227x CPUs
161 /mcf532x Files specific to Freescale ColdFire MCF5329 CPUs
162 /mcf5445x Files specific to Freescale ColdFire MCF5445x CPUs
163 /mcf547x_8x Files specific to Freescale ColdFire MCF547x_8x CPUs
164 /lib Architecture specific library files
165 /microblaze Files generic to microblaze architecture
166 /cpu CPU specific files
167 /lib Architecture specific library files
168 /mips Files generic to MIPS architecture
169 /cpu CPU specific files
170 /mips32 Files specific to MIPS32 CPUs
171 /mips64 Files specific to MIPS64 CPUs
172 /lib Architecture specific library files
173 /nds32 Files generic to NDS32 architecture
174 /cpu CPU specific files
175 /n1213 Files specific to Andes Technology N1213 CPUs
176 /lib Architecture specific library files
177 /nios2 Files generic to Altera NIOS2 architecture
178 /cpu CPU specific files
179 /lib Architecture specific library files
180 /openrisc Files generic to OpenRISC architecture
181 /cpu CPU specific files
182 /lib Architecture specific library files
183 /powerpc Files generic to PowerPC architecture
184 /cpu CPU specific files
185 /mpc5xx Files specific to Freescale MPC5xx CPUs
186 /mpc5xxx Files specific to Freescale MPC5xxx CPUs
187 /mpc8xx Files specific to Freescale MPC8xx CPUs
188 /mpc8260 Files specific to Freescale MPC8260 CPUs
189 /mpc85xx Files specific to Freescale MPC85xx CPUs
190 /ppc4xx Files specific to AMCC PowerPC 4xx CPUs
191 /lib Architecture specific library files
192 /sh Files generic to SH architecture
193 /cpu CPU specific files
194 /sh2 Files specific to sh2 CPUs
195 /sh3 Files specific to sh3 CPUs
196 /sh4 Files specific to sh4 CPUs
197 /lib Architecture specific library files
198 /sparc Files generic to SPARC architecture
199 /cpu CPU specific files
200 /leon2 Files specific to Gaisler LEON2 SPARC CPU
201 /leon3 Files specific to Gaisler LEON3 SPARC CPU
202 /lib Architecture specific library files
203 /x86 Files generic to x86 architecture
204 /cpu CPU specific files
205 /lib Architecture specific library files
206 /api Machine/arch independent API for external apps
207 /board Board dependent files
208 /common Misc architecture independent functions
209 /disk Code for disk drive partition handling
210 /doc Documentation (don't expect too much)
211 /drivers Commonly used device drivers
212 /dts Contains Makefile for building internal U-Boot fdt.
213 /examples Example code for standalone applications, etc.
214 /fs Filesystem code (cramfs, ext2, jffs2, etc.)
215 /include Header Files
216 /lib Files generic to all architectures
217 /libfdt Library files to support flattened device trees
218 /lzma Library files to support LZMA decompression
219 /lzo Library files to support LZO decompression
221 /post Power On Self Test
222 /spl Secondary Program Loader framework
223 /tools Tools to build S-Record or U-Boot images, etc.
225 Software Configuration:
226 =======================
228 Configuration is usually done using C preprocessor defines; the
229 rationale behind that is to avoid dead code whenever possible.
231 There are two classes of configuration variables:
233 * Configuration _OPTIONS_:
234 These are selectable by the user and have names beginning with
237 * Configuration _SETTINGS_:
238 These depend on the hardware etc. and should not be meddled with if
239 you don't know what you're doing; they have names beginning with
242 Later we will add a configuration tool - probably similar to or even
243 identical to what's used for the Linux kernel. Right now, we have to
244 do the configuration by hand, which means creating some symbolic
245 links and editing some configuration files. We use the TQM8xxL boards
249 Selection of Processor Architecture and Board Type:
250 ---------------------------------------------------
252 For all supported boards there are ready-to-use default
253 configurations available; just type "make <board_name>_defconfig".
255 Example: For a TQM823L module type:
258 make TQM823L_defconfig
260 For the Cogent platform, you need to specify the CPU type as well;
261 e.g. "make cogent_mpc8xx_defconfig". And also configure the cogent
262 directory according to the instructions in cogent/README.
268 U-Boot can be built natively to run on a Linux host using the 'sandbox'
269 board. This allows feature development which is not board- or architecture-
270 specific to be undertaken on a native platform. The sandbox is also used to
271 run some of U-Boot's tests.
273 See board/sandbox/README.sandbox for more details.
276 Board Initialisation Flow:
277 --------------------------
279 This is the intended start-up flow for boards. This should apply for both
280 SPL and U-Boot proper (i.e. they both follow the same rules). At present SPL
281 mostly uses a separate code path, but the funtion names and roles of each
282 function are the same. Some boards or architectures may not conform to this.
283 At least most ARM boards which use CONFIG_SPL_FRAMEWORK conform to this.
285 Execution starts with start.S with three functions called during init after
286 that. The purpose and limitations of each is described below.
289 - purpose: essential init to permit execution to reach board_init_f()
290 - no global_data or BSS
291 - there is no stack (ARMv7 may have one but it will soon be removed)
292 - must not set up SDRAM or use console
293 - must only do the bare minimum to allow execution to continue to
295 - this is almost never needed
296 - return normally from this function
299 - purpose: set up the machine ready for running board_init_r():
300 i.e. SDRAM and serial UART
301 - global_data is available
303 - BSS is not available, so you cannot use global/static variables,
304 only stack variables and global_data
306 Non-SPL-specific notes:
307 - dram_init() is called to set up DRAM. If already done in SPL this
311 - you can override the entire board_init_f() function with your own
313 - preloader_console_init() can be called here in extremis
314 - should set up SDRAM, and anything needed to make the UART work
315 - these is no need to clear BSS, it will be done by crt0.S
316 - must return normally from this function (don't call board_init_r()
319 Here the BSS is cleared. For SPL, if CONFIG_SPL_STACK_R is defined, then at
320 this point the stack and global_data are relocated to below
321 CONFIG_SPL_STACK_R_ADDR. For non-SPL, U-Boot is relocated to run at the top of
325 - purpose: main execution, common code
326 - global_data is available
328 - BSS is available, all static/global variables can be used
329 - execution eventually continues to main_loop()
331 Non-SPL-specific notes:
332 - U-Boot is relocated to the top of memory and is now running from
336 - stack is optionally in SDRAM, if CONFIG_SPL_STACK_R is defined and
337 CONFIG_SPL_STACK_R_ADDR points into SDRAM
338 - preloader_console_init() can be called here - typically this is
339 done by defining CONFIG_SPL_BOARD_INIT and then supplying a
340 spl_board_init() function containing this call
341 - loads U-Boot or (in falcon mode) Linux
345 Configuration Options:
346 ----------------------
348 Configuration depends on the combination of board and CPU type; all
349 such information is kept in a configuration file
350 "include/configs/<board_name>.h".
352 Example: For a TQM823L module, all configuration settings are in
353 "include/configs/TQM823L.h".
356 Many of the options are named exactly as the corresponding Linux
357 kernel configuration options. The intention is to make it easier to
358 build a config tool - later.
361 The following options need to be configured:
363 - CPU Type: Define exactly one, e.g. CONFIG_MPC85XX.
365 - Board Type: Define exactly one, e.g. CONFIG_MPC8540ADS.
367 - CPU Daughterboard Type: (if CONFIG_ATSTK1000 is defined)
368 Define exactly one, e.g. CONFIG_ATSTK1002
370 - CPU Module Type: (if CONFIG_COGENT is defined)
371 Define exactly one of
373 --- FIXME --- not tested yet:
374 CONFIG_CMA286_60, CONFIG_CMA286_21, CONFIG_CMA286_60P,
375 CONFIG_CMA287_23, CONFIG_CMA287_50
377 - Motherboard Type: (if CONFIG_COGENT is defined)
378 Define exactly one of
379 CONFIG_CMA101, CONFIG_CMA102
381 - Motherboard I/O Modules: (if CONFIG_COGENT is defined)
382 Define one or more of
385 - Motherboard Options: (if CONFIG_CMA101 or CONFIG_CMA102 are defined)
386 Define one or more of
387 CONFIG_LCD_HEARTBEAT - update a character position on
388 the LCD display every second with
391 - Marvell Family Member
392 CONFIG_SYS_MVFS - define it if you want to enable
393 multiple fs option at one time
394 for marvell soc family
396 - 8xx CPU Options: (if using an MPC8xx CPU)
397 CONFIG_8xx_GCLK_FREQ - deprecated: CPU clock if
398 get_gclk_freq() cannot work
399 e.g. if there is no 32KHz
400 reference PIT/RTC clock
401 CONFIG_8xx_OSCLK - PLL input clock (either EXTCLK
404 - 859/866/885 CPU options: (if using a MPC859 or MPC866 or MPC885 CPU):
405 CONFIG_SYS_8xx_CPUCLK_MIN
406 CONFIG_SYS_8xx_CPUCLK_MAX
407 CONFIG_8xx_CPUCLK_DEFAULT
408 See doc/README.MPC866
410 CONFIG_SYS_MEASURE_CPUCLK
412 Define this to measure the actual CPU clock instead
413 of relying on the correctness of the configured
414 values. Mostly useful for board bringup to make sure
415 the PLL is locked at the intended frequency. Note
416 that this requires a (stable) reference clock (32 kHz
417 RTC clock or CONFIG_SYS_8XX_XIN)
419 CONFIG_SYS_DELAYED_ICACHE
421 Define this option if you want to enable the
422 ICache only when Code runs from RAM.
427 Specifies that the core is a 64-bit PowerPC implementation (implements
428 the "64" category of the Power ISA). This is necessary for ePAPR
429 compliance, among other possible reasons.
431 CONFIG_SYS_FSL_TBCLK_DIV
433 Defines the core time base clock divider ratio compared to the
434 system clock. On most PQ3 devices this is 8, on newer QorIQ
435 devices it can be 16 or 32. The ratio varies from SoC to Soc.
437 CONFIG_SYS_FSL_PCIE_COMPAT
439 Defines the string to utilize when trying to match PCIe device
440 tree nodes for the given platform.
442 CONFIG_SYS_PPC_E500_DEBUG_TLB
444 Enables a temporary TLB entry to be used during boot to work
445 around limitations in e500v1 and e500v2 external debugger
446 support. This reduces the portions of the boot code where
447 breakpoints and single stepping do not work. The value of this
448 symbol should be set to the TLB1 entry to be used for this
451 CONFIG_SYS_FSL_ERRATUM_A004510
453 Enables a workaround for erratum A004510. If set,
454 then CONFIG_SYS_FSL_ERRATUM_A004510_SVR_REV and
455 CONFIG_SYS_FSL_CORENET_SNOOPVEC_COREONLY must be set.
457 CONFIG_SYS_FSL_ERRATUM_A004510_SVR_REV
458 CONFIG_SYS_FSL_ERRATUM_A004510_SVR_REV2 (optional)
460 Defines one or two SoC revisions (low 8 bits of SVR)
461 for which the A004510 workaround should be applied.
463 The rest of SVR is either not relevant to the decision
464 of whether the erratum is present (e.g. p2040 versus
465 p2041) or is implied by the build target, which controls
466 whether CONFIG_SYS_FSL_ERRATUM_A004510 is set.
468 See Freescale App Note 4493 for more information about
471 CONFIG_A003399_NOR_WORKAROUND
472 Enables a workaround for IFC erratum A003399. It is only
473 required during NOR boot.
475 CONFIG_A008044_WORKAROUND
476 Enables a workaround for T1040/T1042 erratum A008044. It is only
477 required during NAND boot and valid for Rev 1.0 SoC revision
479 CONFIG_SYS_FSL_CORENET_SNOOPVEC_COREONLY
481 This is the value to write into CCSR offset 0x18600
482 according to the A004510 workaround.
484 CONFIG_SYS_FSL_DSP_DDR_ADDR
485 This value denotes start offset of DDR memory which is
486 connected exclusively to the DSP cores.
488 CONFIG_SYS_FSL_DSP_M2_RAM_ADDR
489 This value denotes start offset of M2 memory
490 which is directly connected to the DSP core.
492 CONFIG_SYS_FSL_DSP_M3_RAM_ADDR
493 This value denotes start offset of M3 memory which is directly
494 connected to the DSP core.
496 CONFIG_SYS_FSL_DSP_CCSRBAR_DEFAULT
497 This value denotes start offset of DSP CCSR space.
499 CONFIG_SYS_FSL_SINGLE_SOURCE_CLK
500 Single Source Clock is clocking mode present in some of FSL SoC's.
501 In this mode, a single differential clock is used to supply
502 clocks to the sysclock, ddrclock and usbclock.
504 CONFIG_SYS_CPC_REINIT_F
505 This CONFIG is defined when the CPC is configured as SRAM at the
506 time of U-boot entry and is required to be re-initialized.
509 Indicates this SoC supports deep sleep feature. If deep sleep is
510 supported, core will start to execute uboot when wakes up.
512 - Generic CPU options:
513 CONFIG_SYS_GENERIC_GLOBAL_DATA
514 Defines global data is initialized in generic board board_init_f().
515 If this macro is defined, global data is created and cleared in
516 generic board board_init_f(). Without this macro, architecture/board
517 should initialize global data before calling board_init_f().
519 CONFIG_SYS_BIG_ENDIAN, CONFIG_SYS_LITTLE_ENDIAN
521 Defines the endianess of the CPU. Implementation of those
522 values is arch specific.
525 Freescale DDR driver in use. This type of DDR controller is
526 found in mpc83xx, mpc85xx, mpc86xx as well as some ARM core
529 CONFIG_SYS_FSL_DDR_ADDR
530 Freescale DDR memory-mapped register base.
532 CONFIG_SYS_FSL_DDR_EMU
533 Specify emulator support for DDR. Some DDR features such as
534 deskew training are not available.
536 CONFIG_SYS_FSL_DDRC_GEN1
537 Freescale DDR1 controller.
539 CONFIG_SYS_FSL_DDRC_GEN2
540 Freescale DDR2 controller.
542 CONFIG_SYS_FSL_DDRC_GEN3
543 Freescale DDR3 controller.
545 CONFIG_SYS_FSL_DDRC_GEN4
546 Freescale DDR4 controller.
548 CONFIG_SYS_FSL_DDRC_ARM_GEN3
549 Freescale DDR3 controller for ARM-based SoCs.
552 Board config to use DDR1. It can be enabled for SoCs with
553 Freescale DDR1 or DDR2 controllers, depending on the board
557 Board config to use DDR2. It can be eanbeld for SoCs with
558 Freescale DDR2 or DDR3 controllers, depending on the board
562 Board config to use DDR3. It can be enabled for SoCs with
563 Freescale DDR3 or DDR3L controllers.
566 Board config to use DDR3L. It can be enabled for SoCs with
570 Board config to use DDR4. It can be enabled for SoCs with
573 CONFIG_SYS_FSL_IFC_BE
574 Defines the IFC controller register space as Big Endian
576 CONFIG_SYS_FSL_IFC_LE
577 Defines the IFC controller register space as Little Endian
579 CONFIG_SYS_FSL_PBL_PBI
580 It enables addition of RCW (Power on reset configuration) in built image.
581 Please refer doc/README.pblimage for more details
583 CONFIG_SYS_FSL_PBL_RCW
584 It adds PBI(pre-boot instructions) commands in u-boot build image.
585 PBI commands can be used to configure SoC before it starts the execution.
586 Please refer doc/README.pblimage for more details
589 It adds a target to create boot binary having SPL binary in PBI format
590 concatenated with u-boot binary.
592 CONFIG_SYS_FSL_DDR_BE
593 Defines the DDR controller register space as Big Endian
595 CONFIG_SYS_FSL_DDR_LE
596 Defines the DDR controller register space as Little Endian
598 CONFIG_SYS_FSL_DDR_SDRAM_BASE_PHY
599 Physical address from the view of DDR controllers. It is the
600 same as CONFIG_SYS_DDR_SDRAM_BASE for all Power SoCs. But
601 it could be different for ARM SoCs.
603 CONFIG_SYS_FSL_DDR_INTLV_256B
604 DDR controller interleaving on 256-byte. This is a special
605 interleaving mode, handled by Dickens for Freescale layerscape
608 CONFIG_SYS_FSL_DDR_MAIN_NUM_CTRLS
609 Number of controllers used as main memory.
611 CONFIG_SYS_FSL_OTHER_DDR_NUM_CTRLS
612 Number of controllers used for other than main memory.
614 CONFIG_SYS_FSL_SEC_BE
615 Defines the SEC controller register space as Big Endian
617 CONFIG_SYS_FSL_SEC_LE
618 Defines the SEC controller register space as Little Endian
620 - Intel Monahans options:
621 CONFIG_SYS_MONAHANS_RUN_MODE_OSC_RATIO
623 Defines the Monahans run mode to oscillator
624 ratio. Valid values are 8, 16, 24, 31. The core
625 frequency is this value multiplied by 13 MHz.
627 CONFIG_SYS_MONAHANS_TURBO_RUN_MODE_RATIO
629 Defines the Monahans turbo mode to oscillator
630 ratio. Valid values are 1 (default if undefined) and
631 2. The core frequency as calculated above is multiplied
635 CONFIG_SYS_INIT_SP_OFFSET
637 Offset relative to CONFIG_SYS_SDRAM_BASE for initial stack
638 pointer. This is needed for the temporary stack before
641 CONFIG_SYS_MIPS_CACHE_MODE
643 Cache operation mode for the MIPS CPU.
644 See also arch/mips/include/asm/mipsregs.h.
646 CONF_CM_CACHABLE_NO_WA
649 CONF_CM_CACHABLE_NONCOHERENT
653 CONF_CM_CACHABLE_ACCELERATED
655 CONFIG_SYS_XWAY_EBU_BOOTCFG
657 Special option for Lantiq XWAY SoCs for booting from NOR flash.
658 See also arch/mips/cpu/mips32/start.S.
660 CONFIG_XWAY_SWAP_BYTES
662 Enable compilation of tools/xway-swap-bytes needed for Lantiq
663 XWAY SoCs for booting from NOR flash. The U-Boot image needs to
664 be swapped if a flash programmer is used.
667 CONFIG_SYS_EXCEPTION_VECTORS_HIGH
669 Select high exception vectors of the ARM core, e.g., do not
670 clear the V bit of the c1 register of CP15.
672 CONFIG_SYS_THUMB_BUILD
674 Use this flag to build U-Boot using the Thumb instruction
675 set for ARM architectures. Thumb instruction set provides
676 better code density. For ARM architectures that support
677 Thumb2 this flag will result in Thumb2 code generated by
680 CONFIG_ARM_ERRATA_716044
681 CONFIG_ARM_ERRATA_742230
682 CONFIG_ARM_ERRATA_743622
683 CONFIG_ARM_ERRATA_751472
684 CONFIG_ARM_ERRATA_794072
685 CONFIG_ARM_ERRATA_761320
687 If set, the workarounds for these ARM errata are applied early
688 during U-Boot startup. Note that these options force the
689 workarounds to be applied; no CPU-type/version detection
690 exists, unlike the similar options in the Linux kernel. Do not
691 set these options unless they apply!
694 Generic timer clock source frequency.
696 COUNTER_FREQUENCY_REAL
697 Generic timer clock source frequency if the real clock is
698 different from COUNTER_FREQUENCY, and can only be determined
701 NOTE: The following can be machine specific errata. These
702 do have ability to provide rudimentary version and machine
703 specific checks, but expect no product checks.
704 CONFIG_ARM_ERRATA_430973
705 CONFIG_ARM_ERRATA_454179
706 CONFIG_ARM_ERRATA_621766
707 CONFIG_ARM_ERRATA_798870
710 CONFIG_TEGRA_SUPPORT_NON_SECURE
712 Support executing U-Boot in non-secure (NS) mode. Certain
713 impossible actions will be skipped if the CPU is in NS mode,
714 such as ARM architectural timer initialization.
716 - Linux Kernel Interface:
719 U-Boot stores all clock information in Hz
720 internally. For binary compatibility with older Linux
721 kernels (which expect the clocks passed in the
722 bd_info data to be in MHz) the environment variable
723 "clocks_in_mhz" can be defined so that U-Boot
724 converts clock data to MHZ before passing it to the
726 When CONFIG_CLOCKS_IN_MHZ is defined, a definition of
727 "clocks_in_mhz=1" is automatically included in the
730 CONFIG_MEMSIZE_IN_BYTES [relevant for MIPS only]
732 When transferring memsize parameter to Linux, some versions
733 expect it to be in bytes, others in MB.
734 Define CONFIG_MEMSIZE_IN_BYTES to make it in bytes.
738 New kernel versions are expecting firmware settings to be
739 passed using flattened device trees (based on open firmware
743 * New libfdt-based support
744 * Adds the "fdt" command
745 * The bootm command automatically updates the fdt
747 OF_CPU - The proper name of the cpus node (only required for
748 MPC512X and MPC5xxx based boards).
749 OF_SOC - The proper name of the soc node (only required for
750 MPC512X and MPC5xxx based boards).
751 OF_TBCLK - The timebase frequency.
752 OF_STDOUT_PATH - The path to the console device
754 boards with QUICC Engines require OF_QE to set UCC MAC
757 CONFIG_OF_BOARD_SETUP
759 Board code has addition modification that it wants to make
760 to the flat device tree before handing it off to the kernel
762 CONFIG_OF_SYSTEM_SETUP
764 Other code has addition modification that it wants to make
765 to the flat device tree before handing it off to the kernel.
766 This causes ft_system_setup() to be called before booting
771 This define fills in the correct boot CPU in the boot
772 param header, the default value is zero if undefined.
776 U-Boot can detect if an IDE device is present or not.
777 If not, and this new config option is activated, U-Boot
778 removes the ATA node from the DTS before booting Linux,
779 so the Linux IDE driver does not probe the device and
780 crash. This is needed for buggy hardware (uc101) where
781 no pull down resistor is connected to the signal IDE5V_DD7.
783 CONFIG_MACH_TYPE [relevant for ARM only][mandatory]
785 This setting is mandatory for all boards that have only one
786 machine type and must be used to specify the machine type
787 number as it appears in the ARM machine registry
788 (see http://www.arm.linux.org.uk/developer/machines/).
789 Only boards that have multiple machine types supported
790 in a single configuration file and the machine type is
791 runtime discoverable, do not have to use this setting.
793 - vxWorks boot parameters:
795 bootvx constructs a valid bootline using the following
796 environments variables: bootfile, ipaddr, serverip, hostname.
797 It loads the vxWorks image pointed bootfile.
799 CONFIG_SYS_VXWORKS_BOOT_DEVICE - The vxworks device name
800 CONFIG_SYS_VXWORKS_MAC_PTR - Ethernet 6 byte MA -address
801 CONFIG_SYS_VXWORKS_SERVERNAME - Name of the server
802 CONFIG_SYS_VXWORKS_BOOT_ADDR - Address of boot parameters
804 CONFIG_SYS_VXWORKS_ADD_PARAMS
806 Add it at the end of the bootline. E.g "u=username pw=secret"
808 Note: If a "bootargs" environment is defined, it will overwride
809 the defaults discussed just above.
811 - Cache Configuration:
812 CONFIG_SYS_ICACHE_OFF - Do not enable instruction cache in U-Boot
813 CONFIG_SYS_DCACHE_OFF - Do not enable data cache in U-Boot
814 CONFIG_SYS_L2CACHE_OFF- Do not enable L2 cache in U-Boot
816 - Cache Configuration for ARM:
817 CONFIG_SYS_L2_PL310 - Enable support for ARM PL310 L2 cache
819 CONFIG_SYS_PL310_BASE - Physical base address of PL310
820 controller register space
825 Define this if you want support for Amba PrimeCell PL010 UARTs.
829 Define this if you want support for Amba PrimeCell PL011 UARTs.
833 If you have Amba PrimeCell PL011 UARTs, set this variable to
834 the clock speed of the UARTs.
838 If you have Amba PrimeCell PL010 or PL011 UARTs on your board,
839 define this to a list of base addresses for each (supported)
840 port. See e.g. include/configs/versatile.h
842 CONFIG_PL011_SERIAL_RLCR
844 Some vendor versions of PL011 serial ports (e.g. ST-Ericsson U8500)
845 have separate receive and transmit line control registers. Set
846 this variable to initialize the extra register.
848 CONFIG_PL011_SERIAL_FLUSH_ON_INIT
850 On some platforms (e.g. U8500) U-Boot is loaded by a second stage
851 boot loader that has already initialized the UART. Define this
852 variable to flush the UART at init time.
854 CONFIG_SERIAL_HW_FLOW_CONTROL
856 Define this variable to enable hw flow control in serial driver.
857 Current user of this option is drivers/serial/nsl16550.c driver
860 Depending on board, define exactly one serial port
861 (like CONFIG_8xx_CONS_SMC1, CONFIG_8xx_CONS_SMC2,
862 CONFIG_8xx_CONS_SCC1, ...), or switch off the serial
863 console by defining CONFIG_8xx_CONS_NONE
865 Note: if CONFIG_8xx_CONS_NONE is defined, the serial
866 port routines must be defined elsewhere
867 (i.e. serial_init(), serial_getc(), ...)
870 Enables console device for a color framebuffer. Needs following
871 defines (cf. smiLynxEM, i8042)
872 VIDEO_FB_LITTLE_ENDIAN graphic memory organisation
874 VIDEO_HW_RECTFILL graphic chip supports
877 VIDEO_HW_BITBLT graphic chip supports
878 bit-blit (cf. smiLynxEM)
879 VIDEO_VISIBLE_COLS visible pixel columns
881 VIDEO_VISIBLE_ROWS visible pixel rows
882 VIDEO_PIXEL_SIZE bytes per pixel
883 VIDEO_DATA_FORMAT graphic data format
884 (0-5, cf. cfb_console.c)
885 VIDEO_FB_ADRS framebuffer address
886 VIDEO_KBD_INIT_FCT keyboard int fct
887 (i.e. i8042_kbd_init())
888 VIDEO_TSTC_FCT test char fct
890 VIDEO_GETC_FCT get char fct
892 CONFIG_CONSOLE_CURSOR cursor drawing on/off
893 (requires blink timer
895 CONFIG_SYS_CONSOLE_BLINK_COUNT blink interval (cf. i8042.c)
896 CONFIG_CONSOLE_TIME display time/date info in
898 (requires CONFIG_CMD_DATE)
899 CONFIG_VIDEO_LOGO display Linux logo in
901 CONFIG_VIDEO_BMP_LOGO use bmp_logo.h instead of
902 linux_logo.h for logo.
903 Requires CONFIG_VIDEO_LOGO
904 CONFIG_CONSOLE_EXTRA_INFO
905 additional board info beside
908 When CONFIG_CFB_CONSOLE_ANSI is defined, console will support
909 a limited number of ANSI escape sequences (cursor control,
910 erase functions and limited graphics rendition control).
912 When CONFIG_CFB_CONSOLE is defined, video console is
913 default i/o. Serial console can be forced with
914 environment 'console=serial'.
916 When CONFIG_SILENT_CONSOLE is defined, all console
917 messages (by U-Boot and Linux!) can be silenced with
918 the "silent" environment variable. See
919 doc/README.silent for more information.
921 CONFIG_SYS_CONSOLE_BG_COL: define the backgroundcolor, default
923 CONFIG_SYS_CONSOLE_FG_COL: define the foregroundcolor, default
927 CONFIG_BAUDRATE - in bps
928 Select one of the baudrates listed in
929 CONFIG_SYS_BAUDRATE_TABLE, see below.
930 CONFIG_SYS_BRGCLK_PRESCALE, baudrate prescale
932 - Console Rx buffer length
933 With CONFIG_SYS_SMC_RXBUFLEN it is possible to define
934 the maximum receive buffer length for the SMC.
935 This option is actual only for 82xx and 8xx possible.
936 If using CONFIG_SYS_SMC_RXBUFLEN also CONFIG_SYS_MAXIDLE
937 must be defined, to setup the maximum idle timeout for
940 - Pre-Console Buffer:
941 Prior to the console being initialised (i.e. serial UART
942 initialised etc) all console output is silently discarded.
943 Defining CONFIG_PRE_CONSOLE_BUFFER will cause U-Boot to
944 buffer any console messages prior to the console being
945 initialised to a buffer of size CONFIG_PRE_CON_BUF_SZ
946 bytes located at CONFIG_PRE_CON_BUF_ADDR. The buffer is
947 a circular buffer, so if more than CONFIG_PRE_CON_BUF_SZ
948 bytes are output before the console is initialised, the
949 earlier bytes are discarded.
951 Note that when printing the buffer a copy is made on the
952 stack so CONFIG_PRE_CON_BUF_SZ must fit on the stack.
954 'Sane' compilers will generate smaller code if
955 CONFIG_PRE_CON_BUF_SZ is a power of 2
957 - Safe printf() functions
958 Define CONFIG_SYS_VSNPRINTF to compile in safe versions of
959 the printf() functions. These are defined in
960 include/vsprintf.h and include snprintf(), vsnprintf() and
961 so on. Code size increase is approximately 300-500 bytes.
962 If this option is not given then these functions will
963 silently discard their buffer size argument - this means
964 you are not getting any overflow checking in this case.
966 - Boot Delay: CONFIG_BOOTDELAY - in seconds
967 Delay before automatically booting the default image;
968 set to -1 to disable autoboot.
969 set to -2 to autoboot with no delay and not check for abort
970 (even when CONFIG_ZERO_BOOTDELAY_CHECK is defined).
972 See doc/README.autoboot for these options that
973 work with CONFIG_BOOTDELAY. None are required.
974 CONFIG_BOOT_RETRY_TIME
975 CONFIG_BOOT_RETRY_MIN
976 CONFIG_AUTOBOOT_KEYED
977 CONFIG_AUTOBOOT_PROMPT
978 CONFIG_AUTOBOOT_DELAY_STR
979 CONFIG_AUTOBOOT_STOP_STR
980 CONFIG_AUTOBOOT_DELAY_STR2
981 CONFIG_AUTOBOOT_STOP_STR2
982 CONFIG_ZERO_BOOTDELAY_CHECK
983 CONFIG_RESET_TO_RETRY
987 Only needed when CONFIG_BOOTDELAY is enabled;
988 define a command string that is automatically executed
989 when no character is read on the console interface
990 within "Boot Delay" after reset.
993 This can be used to pass arguments to the bootm
994 command. The value of CONFIG_BOOTARGS goes into the
995 environment value "bootargs".
997 CONFIG_RAMBOOT and CONFIG_NFSBOOT
998 The value of these goes into the environment as
999 "ramboot" and "nfsboot" respectively, and can be used
1000 as a convenience, when switching between booting from
1004 CONFIG_BOOTCOUNT_LIMIT
1005 Implements a mechanism for detecting a repeating reboot
1007 http://www.denx.de/wiki/view/DULG/UBootBootCountLimit
1009 CONFIG_BOOTCOUNT_ENV
1010 If no softreset save registers are found on the hardware
1011 "bootcount" is stored in the environment. To prevent a
1012 saveenv on all reboots, the environment variable
1013 "upgrade_available" is used. If "upgrade_available" is
1014 0, "bootcount" is always 0, if "upgrade_available" is
1015 1 "bootcount" is incremented in the environment.
1016 So the Userspace Applikation must set the "upgrade_available"
1017 and "bootcount" variable to 0, if a boot was successfully.
1019 - Pre-Boot Commands:
1022 When this option is #defined, the existence of the
1023 environment variable "preboot" will be checked
1024 immediately before starting the CONFIG_BOOTDELAY
1025 countdown and/or running the auto-boot command resp.
1026 entering interactive mode.
1028 This feature is especially useful when "preboot" is
1029 automatically generated or modified. For an example
1030 see the LWMON board specific code: here "preboot" is
1031 modified when the user holds down a certain
1032 combination of keys on the (special) keyboard when
1035 - Serial Download Echo Mode:
1037 If defined to 1, all characters received during a
1038 serial download (using the "loads" command) are
1039 echoed back. This might be needed by some terminal
1040 emulations (like "cu"), but may as well just take
1041 time on others. This setting #define's the initial
1042 value of the "loads_echo" environment variable.
1044 - Kgdb Serial Baudrate: (if CONFIG_CMD_KGDB is defined)
1045 CONFIG_KGDB_BAUDRATE
1046 Select one of the baudrates listed in
1047 CONFIG_SYS_BAUDRATE_TABLE, see below.
1049 - Monitor Functions:
1050 Monitor commands can be included or excluded
1051 from the build by using the #include files
1052 <config_cmd_all.h> and #undef'ing unwanted
1053 commands, or using <config_cmd_default.h>
1054 and augmenting with additional #define's
1055 for wanted commands.
1057 The default command configuration includes all commands
1058 except those marked below with a "*".
1060 CONFIG_CMD_AES AES 128 CBC encrypt/decrypt
1061 CONFIG_CMD_ASKENV * ask for env variable
1062 CONFIG_CMD_BDI bdinfo
1063 CONFIG_CMD_BEDBUG * Include BedBug Debugger
1064 CONFIG_CMD_BMP * BMP support
1065 CONFIG_CMD_BSP * Board specific commands
1066 CONFIG_CMD_BOOTD bootd
1067 CONFIG_CMD_BOOTI * ARM64 Linux kernel Image support
1068 CONFIG_CMD_CACHE * icache, dcache
1069 CONFIG_CMD_CLK * clock command support
1070 CONFIG_CMD_CONSOLE coninfo
1071 CONFIG_CMD_CRC32 * crc32
1072 CONFIG_CMD_DATE * support for RTC, date/time...
1073 CONFIG_CMD_DHCP * DHCP support
1074 CONFIG_CMD_DIAG * Diagnostics
1075 CONFIG_CMD_DS4510 * ds4510 I2C gpio commands
1076 CONFIG_CMD_DS4510_INFO * ds4510 I2C info command
1077 CONFIG_CMD_DS4510_MEM * ds4510 I2C eeprom/sram commansd
1078 CONFIG_CMD_DS4510_RST * ds4510 I2C rst command
1079 CONFIG_CMD_DTT * Digital Therm and Thermostat
1080 CONFIG_CMD_ECHO echo arguments
1081 CONFIG_CMD_EDITENV edit env variable
1082 CONFIG_CMD_EEPROM * EEPROM read/write support
1083 CONFIG_CMD_ELF * bootelf, bootvx
1084 CONFIG_CMD_ENV_CALLBACK * display details about env callbacks
1085 CONFIG_CMD_ENV_FLAGS * display details about env flags
1086 CONFIG_CMD_ENV_EXISTS * check existence of env variable
1087 CONFIG_CMD_EXPORTENV * export the environment
1088 CONFIG_CMD_EXT2 * ext2 command support
1089 CONFIG_CMD_EXT4 * ext4 command support
1090 CONFIG_CMD_FS_GENERIC * filesystem commands (e.g. load, ls)
1091 that work for multiple fs types
1092 CONFIG_CMD_FS_UUID * Look up a filesystem UUID
1093 CONFIG_CMD_SAVEENV saveenv
1094 CONFIG_CMD_FDC * Floppy Disk Support
1095 CONFIG_CMD_FAT * FAT command support
1096 CONFIG_CMD_FLASH flinfo, erase, protect
1097 CONFIG_CMD_FPGA FPGA device initialization support
1098 CONFIG_CMD_FUSE * Device fuse support
1099 CONFIG_CMD_GETTIME * Get time since boot
1100 CONFIG_CMD_GO * the 'go' command (exec code)
1101 CONFIG_CMD_GREPENV * search environment
1102 CONFIG_CMD_HASH * calculate hash / digest
1103 CONFIG_CMD_HWFLOW * RTS/CTS hw flow control
1104 CONFIG_CMD_I2C * I2C serial bus support
1105 CONFIG_CMD_IDE * IDE harddisk support
1106 CONFIG_CMD_IMI iminfo
1107 CONFIG_CMD_IMLS List all images found in NOR flash
1108 CONFIG_CMD_IMLS_NAND * List all images found in NAND flash
1109 CONFIG_CMD_IMMAP * IMMR dump support
1110 CONFIG_CMD_IOTRACE * I/O tracing for debugging
1111 CONFIG_CMD_IMPORTENV * import an environment
1112 CONFIG_CMD_INI * import data from an ini file into the env
1113 CONFIG_CMD_IRQ * irqinfo
1114 CONFIG_CMD_ITEST Integer/string test of 2 values
1115 CONFIG_CMD_JFFS2 * JFFS2 Support
1116 CONFIG_CMD_KGDB * kgdb
1117 CONFIG_CMD_LDRINFO * ldrinfo (display Blackfin loader)
1118 CONFIG_CMD_LINK_LOCAL * link-local IP address auto-configuration
1120 CONFIG_CMD_LOADB loadb
1121 CONFIG_CMD_LOADS loads
1122 CONFIG_CMD_MD5SUM * print md5 message digest
1123 (requires CONFIG_CMD_MEMORY and CONFIG_MD5)
1124 CONFIG_CMD_MEMINFO * Display detailed memory information
1125 CONFIG_CMD_MEMORY md, mm, nm, mw, cp, cmp, crc, base,
1127 CONFIG_CMD_MEMTEST * mtest
1128 CONFIG_CMD_MISC Misc functions like sleep etc
1129 CONFIG_CMD_MMC * MMC memory mapped support
1130 CONFIG_CMD_MII * MII utility commands
1131 CONFIG_CMD_MTDPARTS * MTD partition support
1132 CONFIG_CMD_NAND * NAND support
1133 CONFIG_CMD_NET bootp, tftpboot, rarpboot
1134 CONFIG_CMD_NFS NFS support
1135 CONFIG_CMD_PCA953X * PCA953x I2C gpio commands
1136 CONFIG_CMD_PCA953X_INFO * PCA953x I2C gpio info command
1137 CONFIG_CMD_PCI * pciinfo
1138 CONFIG_CMD_PCMCIA * PCMCIA support
1139 CONFIG_CMD_PING * send ICMP ECHO_REQUEST to network
1141 CONFIG_CMD_PORTIO * Port I/O
1142 CONFIG_CMD_READ * Read raw data from partition
1143 CONFIG_CMD_REGINFO * Register dump
1144 CONFIG_CMD_RUN run command in env variable
1145 CONFIG_CMD_SANDBOX * sb command to access sandbox features
1146 CONFIG_CMD_SAVES * save S record dump
1147 CONFIG_CMD_SCSI * SCSI Support
1148 CONFIG_CMD_SDRAM * print SDRAM configuration information
1149 (requires CONFIG_CMD_I2C)
1150 CONFIG_CMD_SETGETDCR Support for DCR Register access
1152 CONFIG_CMD_SF * Read/write/erase SPI NOR flash
1153 CONFIG_CMD_SHA1SUM * print sha1 memory digest
1154 (requires CONFIG_CMD_MEMORY)
1155 CONFIG_CMD_SOFTSWITCH * Soft switch setting command for BF60x
1156 CONFIG_CMD_SOURCE "source" command Support
1157 CONFIG_CMD_SPI * SPI serial bus support
1158 CONFIG_CMD_TFTPSRV * TFTP transfer in server mode
1159 CONFIG_CMD_TFTPPUT * TFTP put command (upload)
1160 CONFIG_CMD_TIME * run command and report execution time (ARM specific)
1161 CONFIG_CMD_TIMER * access to the system tick timer
1162 CONFIG_CMD_USB * USB support
1163 CONFIG_CMD_CDP * Cisco Discover Protocol support
1164 CONFIG_CMD_MFSL * Microblaze FSL support
1165 CONFIG_CMD_XIMG Load part of Multi Image
1166 CONFIG_CMD_UUID * Generate random UUID or GUID string
1168 EXAMPLE: If you want all functions except of network
1169 support you can write:
1171 #include "config_cmd_all.h"
1172 #undef CONFIG_CMD_NET
1175 fdt (flattened device tree) command: CONFIG_OF_LIBFDT
1177 Note: Don't enable the "icache" and "dcache" commands
1178 (configuration option CONFIG_CMD_CACHE) unless you know
1179 what you (and your U-Boot users) are doing. Data
1180 cache cannot be enabled on systems like the 8xx or
1181 8260 (where accesses to the IMMR region must be
1182 uncached), and it cannot be disabled on all other
1183 systems where we (mis-) use the data cache to hold an
1184 initial stack and some data.
1187 XXX - this list needs to get updated!
1189 - Regular expression support:
1191 If this variable is defined, U-Boot is linked against
1192 the SLRE (Super Light Regular Expression) library,
1193 which adds regex support to some commands, as for
1194 example "env grep" and "setexpr".
1198 If this variable is defined, U-Boot will use a device tree
1199 to configure its devices, instead of relying on statically
1200 compiled #defines in the board file. This option is
1201 experimental and only available on a few boards. The device
1202 tree is available in the global data as gd->fdt_blob.
1204 U-Boot needs to get its device tree from somewhere. This can
1205 be done using one of the two options below:
1208 If this variable is defined, U-Boot will embed a device tree
1209 binary in its image. This device tree file should be in the
1210 board directory and called <soc>-<board>.dts. The binary file
1211 is then picked up in board_init_f() and made available through
1212 the global data structure as gd->blob.
1215 If this variable is defined, U-Boot will build a device tree
1216 binary. It will be called u-boot.dtb. Architecture-specific
1217 code will locate it at run-time. Generally this works by:
1219 cat u-boot.bin u-boot.dtb >image.bin
1221 and in fact, U-Boot does this for you, creating a file called
1222 u-boot-dtb.bin which is useful in the common case. You can
1223 still use the individual files if you need something more
1228 If this variable is defined, it enables watchdog
1229 support for the SoC. There must be support in the SoC
1230 specific code for a watchdog. For the 8xx and 8260
1231 CPUs, the SIU Watchdog feature is enabled in the SYPCR
1232 register. When supported for a specific SoC is
1233 available, then no further board specific code should
1234 be needed to use it.
1237 When using a watchdog circuitry external to the used
1238 SoC, then define this variable and provide board
1239 specific code for the "hw_watchdog_reset" function.
1241 CONFIG_AT91_HW_WDT_TIMEOUT
1242 specify the timeout in seconds. default 2 seconds.
1245 CONFIG_VERSION_VARIABLE
1246 If this variable is defined, an environment variable
1247 named "ver" is created by U-Boot showing the U-Boot
1248 version as printed by the "version" command.
1249 Any change to this variable will be reverted at the
1254 When CONFIG_CMD_DATE is selected, the type of the RTC
1255 has to be selected, too. Define exactly one of the
1258 CONFIG_RTC_MPC8xx - use internal RTC of MPC8xx
1259 CONFIG_RTC_PCF8563 - use Philips PCF8563 RTC
1260 CONFIG_RTC_MC13XXX - use MC13783 or MC13892 RTC
1261 CONFIG_RTC_MC146818 - use MC146818 RTC
1262 CONFIG_RTC_DS1307 - use Maxim, Inc. DS1307 RTC
1263 CONFIG_RTC_DS1337 - use Maxim, Inc. DS1337 RTC
1264 CONFIG_RTC_DS1338 - use Maxim, Inc. DS1338 RTC
1265 CONFIG_RTC_DS1339 - use Maxim, Inc. DS1339 RTC
1266 CONFIG_RTC_DS164x - use Dallas DS164x RTC
1267 CONFIG_RTC_ISL1208 - use Intersil ISL1208 RTC
1268 CONFIG_RTC_MAX6900 - use Maxim, Inc. MAX6900 RTC
1269 CONFIG_SYS_RTC_DS1337_NOOSC - Turn off the OSC output for DS1337
1270 CONFIG_SYS_RV3029_TCR - enable trickle charger on
1273 Note that if the RTC uses I2C, then the I2C interface
1274 must also be configured. See I2C Support, below.
1277 CONFIG_PCA953X - use NXP's PCA953X series I2C GPIO
1279 The CONFIG_SYS_I2C_PCA953X_WIDTH option specifies a list of
1280 chip-ngpio pairs that tell the PCA953X driver the number of
1281 pins supported by a particular chip.
1283 Note that if the GPIO device uses I2C, then the I2C interface
1284 must also be configured. See I2C Support, below.
1287 When CONFIG_IO_TRACE is selected, U-Boot intercepts all I/O
1288 accesses and can checksum them or write a list of them out
1289 to memory. See the 'iotrace' command for details. This is
1290 useful for testing device drivers since it can confirm that
1291 the driver behaves the same way before and after a code
1292 change. Currently this is supported on sandbox and arm. To
1293 add support for your architecture, add '#include <iotrace.h>'
1294 to the bottom of arch/<arch>/include/asm/io.h and test.
1296 Example output from the 'iotrace stats' command is below.
1297 Note that if the trace buffer is exhausted, the checksum will
1298 still continue to operate.
1301 Start: 10000000 (buffer start address)
1302 Size: 00010000 (buffer size)
1303 Offset: 00000120 (current buffer offset)
1304 Output: 10000120 (start + offset)
1305 Count: 00000018 (number of trace records)
1306 CRC32: 9526fb66 (CRC32 of all trace records)
1308 - Timestamp Support:
1310 When CONFIG_TIMESTAMP is selected, the timestamp
1311 (date and time) of an image is printed by image
1312 commands like bootm or iminfo. This option is
1313 automatically enabled when you select CONFIG_CMD_DATE .
1315 - Partition Labels (disklabels) Supported:
1316 Zero or more of the following:
1317 CONFIG_MAC_PARTITION Apple's MacOS partition table.
1318 CONFIG_DOS_PARTITION MS Dos partition table, traditional on the
1319 Intel architecture, USB sticks, etc.
1320 CONFIG_ISO_PARTITION ISO partition table, used on CDROM etc.
1321 CONFIG_EFI_PARTITION GPT partition table, common when EFI is the
1322 bootloader. Note 2TB partition limit; see
1324 CONFIG_MTD_PARTITIONS Memory Technology Device partition table.
1326 If IDE or SCSI support is enabled (CONFIG_CMD_IDE or
1327 CONFIG_CMD_SCSI) you must configure support for at
1328 least one non-MTD partition type as well.
1331 CONFIG_IDE_RESET_ROUTINE - this is defined in several
1332 board configurations files but used nowhere!
1334 CONFIG_IDE_RESET - is this is defined, IDE Reset will
1335 be performed by calling the function
1336 ide_set_reset(int reset)
1337 which has to be defined in a board specific file
1342 Set this to enable ATAPI support.
1347 Set this to enable support for disks larger than 137GB
1348 Also look at CONFIG_SYS_64BIT_LBA.
1349 Whithout these , LBA48 support uses 32bit variables and will 'only'
1350 support disks up to 2.1TB.
1352 CONFIG_SYS_64BIT_LBA:
1353 When enabled, makes the IDE subsystem use 64bit sector addresses.
1357 At the moment only there is only support for the
1358 SYM53C8XX SCSI controller; define
1359 CONFIG_SCSI_SYM53C8XX to enable it.
1361 CONFIG_SYS_SCSI_MAX_LUN [8], CONFIG_SYS_SCSI_MAX_SCSI_ID [7] and
1362 CONFIG_SYS_SCSI_MAX_DEVICE [CONFIG_SYS_SCSI_MAX_SCSI_ID *
1363 CONFIG_SYS_SCSI_MAX_LUN] can be adjusted to define the
1364 maximum numbers of LUNs, SCSI ID's and target
1366 CONFIG_SYS_SCSI_SYM53C8XX_CCF to fix clock timing (80Mhz)
1368 The environment variable 'scsidevs' is set to the number of
1369 SCSI devices found during the last scan.
1371 - NETWORK Support (PCI):
1373 Support for Intel 8254x/8257x gigabit chips.
1376 Utility code for direct access to the SPI bus on Intel 8257x.
1377 This does not do anything useful unless you set at least one
1378 of CONFIG_CMD_E1000 or CONFIG_E1000_SPI_GENERIC.
1380 CONFIG_E1000_SPI_GENERIC
1381 Allow generic access to the SPI bus on the Intel 8257x, for
1382 example with the "sspi" command.
1385 Management command for E1000 devices. When used on devices
1386 with SPI support you can reprogram the EEPROM from U-Boot.
1388 CONFIG_E1000_FALLBACK_MAC
1389 default MAC for empty EEPROM after production.
1392 Support for Intel 82557/82559/82559ER chips.
1393 Optional CONFIG_EEPRO100_SROM_WRITE enables EEPROM
1394 write routine for first time initialisation.
1397 Support for Digital 2114x chips.
1398 Optional CONFIG_TULIP_SELECT_MEDIA for board specific
1399 modem chip initialisation (KS8761/QS6611).
1402 Support for National dp83815 chips.
1405 Support for National dp8382[01] gigabit chips.
1407 - NETWORK Support (other):
1409 CONFIG_DRIVER_AT91EMAC
1410 Support for AT91RM9200 EMAC.
1413 Define this to use reduced MII inteface
1415 CONFIG_DRIVER_AT91EMAC_QUIET
1416 If this defined, the driver is quiet.
1417 The driver doen't show link status messages.
1419 CONFIG_CALXEDA_XGMAC
1420 Support for the Calxeda XGMAC device
1423 Support for SMSC's LAN91C96 chips.
1425 CONFIG_LAN91C96_BASE
1426 Define this to hold the physical address
1427 of the LAN91C96's I/O space
1429 CONFIG_LAN91C96_USE_32_BIT
1430 Define this to enable 32 bit addressing
1433 Support for SMSC's LAN91C111 chip
1435 CONFIG_SMC91111_BASE
1436 Define this to hold the physical address
1437 of the device (I/O space)
1439 CONFIG_SMC_USE_32_BIT
1440 Define this if data bus is 32 bits
1442 CONFIG_SMC_USE_IOFUNCS
1443 Define this to use i/o functions instead of macros
1444 (some hardware wont work with macros)
1446 CONFIG_DRIVER_TI_EMAC
1447 Support for davinci emac
1449 CONFIG_SYS_DAVINCI_EMAC_PHY_COUNT
1450 Define this if you have more then 3 PHYs.
1453 Support for Faraday's FTGMAC100 Gigabit SoC Ethernet
1455 CONFIG_FTGMAC100_EGIGA
1456 Define this to use GE link update with gigabit PHY.
1457 Define this if FTGMAC100 is connected to gigabit PHY.
1458 If your system has 10/100 PHY only, it might not occur
1459 wrong behavior. Because PHY usually return timeout or
1460 useless data when polling gigabit status and gigabit
1461 control registers. This behavior won't affect the
1462 correctnessof 10/100 link speed update.
1465 Support for SMSC's LAN911x and LAN921x chips
1468 Define this to hold the physical address
1469 of the device (I/O space)
1471 CONFIG_SMC911X_32_BIT
1472 Define this if data bus is 32 bits
1474 CONFIG_SMC911X_16_BIT
1475 Define this if data bus is 16 bits. If your processor
1476 automatically converts one 32 bit word to two 16 bit
1477 words you may also try CONFIG_SMC911X_32_BIT.
1480 Support for Renesas on-chip Ethernet controller
1482 CONFIG_SH_ETHER_USE_PORT
1483 Define the number of ports to be used
1485 CONFIG_SH_ETHER_PHY_ADDR
1486 Define the ETH PHY's address
1488 CONFIG_SH_ETHER_CACHE_WRITEBACK
1489 If this option is set, the driver enables cache flush.
1493 Support for PWM modul on the imx6.
1497 Support TPM devices.
1500 Support for i2c bus TPM devices. Only one device
1501 per system is supported at this time.
1503 CONFIG_TPM_TIS_I2C_BUS_NUMBER
1504 Define the the i2c bus number for the TPM device
1506 CONFIG_TPM_TIS_I2C_SLAVE_ADDRESS
1507 Define the TPM's address on the i2c bus
1509 CONFIG_TPM_TIS_I2C_BURST_LIMITATION
1510 Define the burst count bytes upper limit
1512 CONFIG_TPM_ATMEL_TWI
1513 Support for Atmel TWI TPM device. Requires I2C support.
1516 Support for generic parallel port TPM devices. Only one device
1517 per system is supported at this time.
1519 CONFIG_TPM_TIS_BASE_ADDRESS
1520 Base address where the generic TPM device is mapped
1521 to. Contemporary x86 systems usually map it at
1525 Add tpm monitor functions.
1526 Requires CONFIG_TPM. If CONFIG_TPM_AUTH_SESSIONS is set, also
1527 provides monitor access to authorized functions.
1530 Define this to enable the TPM support library which provides
1531 functional interfaces to some TPM commands.
1532 Requires support for a TPM device.
1534 CONFIG_TPM_AUTH_SESSIONS
1535 Define this to enable authorized functions in the TPM library.
1536 Requires CONFIG_TPM and CONFIG_SHA1.
1539 At the moment only the UHCI host controller is
1540 supported (PIP405, MIP405, MPC5200); define
1541 CONFIG_USB_UHCI to enable it.
1542 define CONFIG_USB_KEYBOARD to enable the USB Keyboard
1543 and define CONFIG_USB_STORAGE to enable the USB
1546 Supported are USB Keyboards and USB Floppy drives
1548 MPC5200 USB requires additional defines:
1550 for 528 MHz Clock: 0x0001bbbb
1554 for differential drivers: 0x00001000
1555 for single ended drivers: 0x00005000
1556 for differential drivers on PSC3: 0x00000100
1557 for single ended drivers on PSC3: 0x00004100
1558 CONFIG_SYS_USB_EVENT_POLL
1559 May be defined to allow interrupt polling
1560 instead of using asynchronous interrupts
1562 CONFIG_USB_EHCI_TXFIFO_THRESH enables setting of the
1563 txfilltuning field in the EHCI controller on reset.
1565 CONFIG_USB_DWC2_REG_ADDR the physical CPU address of the DWC2
1566 HW module registers.
1569 Define the below if you wish to use the USB console.
1570 Once firmware is rebuilt from a serial console issue the
1571 command "setenv stdin usbtty; setenv stdout usbtty" and
1572 attach your USB cable. The Unix command "dmesg" should print
1573 it has found a new device. The environment variable usbtty
1574 can be set to gserial or cdc_acm to enable your device to
1575 appear to a USB host as a Linux gserial device or a
1576 Common Device Class Abstract Control Model serial device.
1577 If you select usbtty = gserial you should be able to enumerate
1579 # modprobe usbserial vendor=0xVendorID product=0xProductID
1580 else if using cdc_acm, simply setting the environment
1581 variable usbtty to be cdc_acm should suffice. The following
1582 might be defined in YourBoardName.h
1585 Define this to build a UDC device
1588 Define this to have a tty type of device available to
1589 talk to the UDC device
1592 Define this to enable the high speed support for usb
1593 device and usbtty. If this feature is enabled, a routine
1594 int is_usbd_high_speed(void)
1595 also needs to be defined by the driver to dynamically poll
1596 whether the enumeration has succeded at high speed or full
1599 CONFIG_SYS_CONSOLE_IS_IN_ENV
1600 Define this if you want stdin, stdout &/or stderr to
1604 CONFIG_SYS_USB_EXTC_CLK 0xBLAH
1605 Derive USB clock from external clock "blah"
1606 - CONFIG_SYS_USB_EXTC_CLK 0x02
1608 CONFIG_SYS_USB_BRG_CLK 0xBLAH
1609 Derive USB clock from brgclk
1610 - CONFIG_SYS_USB_BRG_CLK 0x04
1612 If you have a USB-IF assigned VendorID then you may wish to
1613 define your own vendor specific values either in BoardName.h
1614 or directly in usbd_vendor_info.h. If you don't define
1615 CONFIG_USBD_MANUFACTURER, CONFIG_USBD_PRODUCT_NAME,
1616 CONFIG_USBD_VENDORID and CONFIG_USBD_PRODUCTID, then U-Boot
1617 should pretend to be a Linux device to it's target host.
1619 CONFIG_USBD_MANUFACTURER
1620 Define this string as the name of your company for
1621 - CONFIG_USBD_MANUFACTURER "my company"
1623 CONFIG_USBD_PRODUCT_NAME
1624 Define this string as the name of your product
1625 - CONFIG_USBD_PRODUCT_NAME "acme usb device"
1627 CONFIG_USBD_VENDORID
1628 Define this as your assigned Vendor ID from the USB
1629 Implementors Forum. This *must* be a genuine Vendor ID
1630 to avoid polluting the USB namespace.
1631 - CONFIG_USBD_VENDORID 0xFFFF
1633 CONFIG_USBD_PRODUCTID
1634 Define this as the unique Product ID
1636 - CONFIG_USBD_PRODUCTID 0xFFFF
1638 - ULPI Layer Support:
1639 The ULPI (UTMI Low Pin (count) Interface) PHYs are supported via
1640 the generic ULPI layer. The generic layer accesses the ULPI PHY
1641 via the platform viewport, so you need both the genric layer and
1642 the viewport enabled. Currently only Chipidea/ARC based
1643 viewport is supported.
1644 To enable the ULPI layer support, define CONFIG_USB_ULPI and
1645 CONFIG_USB_ULPI_VIEWPORT in your board configuration file.
1646 If your ULPI phy needs a different reference clock than the
1647 standard 24 MHz then you have to define CONFIG_ULPI_REF_CLK to
1648 the appropriate value in Hz.
1651 The MMC controller on the Intel PXA is supported. To
1652 enable this define CONFIG_MMC. The MMC can be
1653 accessed from the boot prompt by mapping the device
1654 to physical memory similar to flash. Command line is
1655 enabled with CONFIG_CMD_MMC. The MMC driver also works with
1656 the FAT fs. This is enabled with CONFIG_CMD_FAT.
1659 Support for Renesas on-chip MMCIF controller
1661 CONFIG_SH_MMCIF_ADDR
1662 Define the base address of MMCIF registers
1665 Define the clock frequency for MMCIF
1668 Enable the generic MMC driver
1670 CONFIG_SUPPORT_EMMC_BOOT
1671 Enable some additional features of the eMMC boot partitions.
1673 CONFIG_SUPPORT_EMMC_RPMB
1674 Enable the commands for reading, writing and programming the
1675 key for the Replay Protection Memory Block partition in eMMC.
1677 - USB Device Firmware Update (DFU) class support:
1679 This enables the USB portion of the DFU USB class
1682 This enables the command "dfu" which is used to have
1683 U-Boot create a DFU class device via USB. This command
1684 requires that the "dfu_alt_info" environment variable be
1685 set and define the alt settings to expose to the host.
1688 This enables support for exposing (e)MMC devices via DFU.
1691 This enables support for exposing NAND devices via DFU.
1694 This enables support for exposing RAM via DFU.
1695 Note: DFU spec refer to non-volatile memory usage, but
1696 allow usages beyond the scope of spec - here RAM usage,
1697 one that would help mostly the developer.
1699 CONFIG_SYS_DFU_DATA_BUF_SIZE
1700 Dfu transfer uses a buffer before writing data to the
1701 raw storage device. Make the size (in bytes) of this buffer
1702 configurable. The size of this buffer is also configurable
1703 through the "dfu_bufsiz" environment variable.
1705 CONFIG_SYS_DFU_MAX_FILE_SIZE
1706 When updating files rather than the raw storage device,
1707 we use a static buffer to copy the file into and then write
1708 the buffer once we've been given the whole file. Define
1709 this to the maximum filesize (in bytes) for the buffer.
1710 Default is 4 MiB if undefined.
1712 DFU_DEFAULT_POLL_TIMEOUT
1713 Poll timeout [ms], is the timeout a device can send to the
1714 host. The host must wait for this timeout before sending
1715 a subsequent DFU_GET_STATUS request to the device.
1717 DFU_MANIFEST_POLL_TIMEOUT
1718 Poll timeout [ms], which the device sends to the host when
1719 entering dfuMANIFEST state. Host waits this timeout, before
1720 sending again an USB request to the device.
1722 - USB Device Android Fastboot support:
1724 This enables the command "fastboot" which enables the Android
1725 fastboot mode for the platform's USB device. Fastboot is a USB
1726 protocol for downloading images, flashing and device control
1727 used on Android devices.
1728 See doc/README.android-fastboot for more information.
1730 CONFIG_ANDROID_BOOT_IMAGE
1731 This enables support for booting images which use the Android
1732 image format header.
1734 CONFIG_USB_FASTBOOT_BUF_ADDR
1735 The fastboot protocol requires a large memory buffer for
1736 downloads. Define this to the starting RAM address to use for
1739 CONFIG_USB_FASTBOOT_BUF_SIZE
1740 The fastboot protocol requires a large memory buffer for
1741 downloads. This buffer should be as large as possible for a
1742 platform. Define this to the size available RAM for fastboot.
1744 CONFIG_FASTBOOT_FLASH
1745 The fastboot protocol includes a "flash" command for writing
1746 the downloaded image to a non-volatile storage device. Define
1747 this to enable the "fastboot flash" command.
1749 CONFIG_FASTBOOT_FLASH_MMC_DEV
1750 The fastboot "flash" command requires additional information
1751 regarding the non-volatile storage device. Define this to
1752 the eMMC device that fastboot should use to store the image.
1754 CONFIG_FASTBOOT_GPT_NAME
1755 The fastboot "flash" command supports writing the downloaded
1756 image to the Protective MBR and the Primary GUID Partition
1757 Table. (Additionally, this downloaded image is post-processed
1758 to generate and write the Backup GUID Partition Table.)
1759 This occurs when the specified "partition name" on the
1760 "fastboot flash" command line matches this value.
1761 Default is GPT_ENTRY_NAME (currently "gpt") if undefined.
1763 - Journaling Flash filesystem support:
1764 CONFIG_JFFS2_NAND, CONFIG_JFFS2_NAND_OFF, CONFIG_JFFS2_NAND_SIZE,
1765 CONFIG_JFFS2_NAND_DEV
1766 Define these for a default partition on a NAND device
1768 CONFIG_SYS_JFFS2_FIRST_SECTOR,
1769 CONFIG_SYS_JFFS2_FIRST_BANK, CONFIG_SYS_JFFS2_NUM_BANKS
1770 Define these for a default partition on a NOR device
1772 CONFIG_SYS_JFFS_CUSTOM_PART
1773 Define this to create an own partition. You have to provide a
1774 function struct part_info* jffs2_part_info(int part_num)
1776 If you define only one JFFS2 partition you may also want to
1777 #define CONFIG_SYS_JFFS_SINGLE_PART 1
1778 to disable the command chpart. This is the default when you
1779 have not defined a custom partition
1781 - FAT(File Allocation Table) filesystem write function support:
1784 Define this to enable support for saving memory data as a
1785 file in FAT formatted partition.
1787 This will also enable the command "fatwrite" enabling the
1788 user to write files to FAT.
1790 CBFS (Coreboot Filesystem) support
1793 Define this to enable support for reading from a Coreboot
1794 filesystem. Available commands are cbfsinit, cbfsinfo, cbfsls
1797 - FAT(File Allocation Table) filesystem cluster size:
1798 CONFIG_FS_FAT_MAX_CLUSTSIZE
1800 Define the max cluster size for fat operations else
1801 a default value of 65536 will be defined.
1806 Define this to enable standard (PC-Style) keyboard
1810 Standard PC keyboard driver with US (is default) and
1811 GERMAN key layout (switch via environment 'keymap=de') support.
1812 Export function i8042_kbd_init, i8042_tstc and i8042_getc
1813 for cfb_console. Supports cursor blinking.
1816 Enables a Chrome OS keyboard using the CROS_EC interface.
1817 This uses CROS_EC to communicate with a second microcontroller
1818 which provides key scans on request.
1823 Define this to enable video support (for output to
1826 CONFIG_VIDEO_CT69000
1828 Enable Chips & Technologies 69000 Video chip
1830 CONFIG_VIDEO_SMI_LYNXEM
1831 Enable Silicon Motion SMI 712/710/810 Video chip. The
1832 video output is selected via environment 'videoout'
1833 (1 = LCD and 2 = CRT). If videoout is undefined, CRT is
1836 For the CT69000 and SMI_LYNXEM drivers, videomode is
1837 selected via environment 'videomode'. Two different ways
1839 - "videomode=num" 'num' is a standard LiLo mode numbers.
1840 Following standard modes are supported (* is default):
1842 Colors 640x480 800x600 1024x768 1152x864 1280x1024
1843 -------------+---------------------------------------------
1844 8 bits | 0x301* 0x303 0x305 0x161 0x307
1845 15 bits | 0x310 0x313 0x316 0x162 0x319
1846 16 bits | 0x311 0x314 0x317 0x163 0x31A
1847 24 bits | 0x312 0x315 0x318 ? 0x31B
1848 -------------+---------------------------------------------
1849 (i.e. setenv videomode 317; saveenv; reset;)
1851 - "videomode=bootargs" all the video parameters are parsed
1852 from the bootargs. (See drivers/video/videomodes.c)
1855 CONFIG_VIDEO_SED13806
1856 Enable Epson SED13806 driver. This driver supports 8bpp
1857 and 16bpp modes defined by CONFIG_VIDEO_SED13806_8BPP
1858 or CONFIG_VIDEO_SED13806_16BPP
1861 Enable the Freescale DIU video driver. Reference boards for
1862 SOCs that have a DIU should define this macro to enable DIU
1863 support, and should also define these other macros:
1869 CONFIG_VIDEO_SW_CURSOR
1870 CONFIG_VGA_AS_SINGLE_DEVICE
1872 CONFIG_VIDEO_BMP_LOGO
1874 The DIU driver will look for the 'video-mode' environment
1875 variable, and if defined, enable the DIU as a console during
1876 boot. See the documentation file README.video for a
1877 description of this variable.
1883 Define this to enable a custom keyboard support.
1884 This simply calls drv_keyboard_init() which must be
1885 defined in your board-specific files.
1886 The only board using this so far is RBC823.
1888 - LCD Support: CONFIG_LCD
1890 Define this to enable LCD support (for output to LCD
1891 display); also select one of the supported displays
1892 by defining one of these:
1896 HITACHI TX09D70VM1CCA, 3.5", 240x320.
1898 CONFIG_NEC_NL6448AC33:
1900 NEC NL6448AC33-18. Active, color, single scan.
1902 CONFIG_NEC_NL6448BC20
1904 NEC NL6448BC20-08. 6.5", 640x480.
1905 Active, color, single scan.
1907 CONFIG_NEC_NL6448BC33_54
1909 NEC NL6448BC33-54. 10.4", 640x480.
1910 Active, color, single scan.
1914 Sharp 320x240. Active, color, single scan.
1915 It isn't 16x9, and I am not sure what it is.
1917 CONFIG_SHARP_LQ64D341
1919 Sharp LQ64D341 display, 640x480.
1920 Active, color, single scan.
1924 HLD1045 display, 640x480.
1925 Active, color, single scan.
1929 Optrex CBL50840-2 NF-FW 99 22 M5
1931 Hitachi LMG6912RPFC-00T
1935 320x240. Black & white.
1937 Normally display is black on white background; define
1938 CONFIG_SYS_WHITE_ON_BLACK to get it inverted.
1940 CONFIG_LCD_ALIGNMENT
1942 Normally the LCD is page-aligned (typically 4KB). If this is
1943 defined then the LCD will be aligned to this value instead.
1944 For ARM it is sometimes useful to use MMU_SECTION_SIZE
1945 here, since it is cheaper to change data cache settings on
1946 a per-section basis.
1948 CONFIG_CONSOLE_SCROLL_LINES
1950 When the console need to be scrolled, this is the number of
1951 lines to scroll by. It defaults to 1. Increasing this makes
1952 the console jump but can help speed up operation when scrolling
1957 Sometimes, for example if the display is mounted in portrait
1958 mode or even if it's mounted landscape but rotated by 180degree,
1959 we need to rotate our content of the display relative to the
1960 framebuffer, so that user can read the messages which are
1962 Once CONFIG_LCD_ROTATION is defined, the lcd_console will be
1963 initialized with a given rotation from "vl_rot" out of
1964 "vidinfo_t" which is provided by the board specific code.
1965 The value for vl_rot is coded as following (matching to
1966 fbcon=rotate:<n> linux-kernel commandline):
1967 0 = no rotation respectively 0 degree
1968 1 = 90 degree rotation
1969 2 = 180 degree rotation
1970 3 = 270 degree rotation
1972 If CONFIG_LCD_ROTATION is not defined, the console will be
1973 initialized with 0degree rotation.
1977 Support drawing of RLE8-compressed bitmaps on the LCD.
1981 Enables an 'i2c edid' command which can read EDID
1982 information over I2C from an attached LCD display.
1984 - Splash Screen Support: CONFIG_SPLASH_SCREEN
1986 If this option is set, the environment is checked for
1987 a variable "splashimage". If found, the usual display
1988 of logo, copyright and system information on the LCD
1989 is suppressed and the BMP image at the address
1990 specified in "splashimage" is loaded instead. The
1991 console is redirected to the "nulldev", too. This
1992 allows for a "silent" boot where a splash screen is
1993 loaded very quickly after power-on.
1995 CONFIG_SPLASHIMAGE_GUARD
1997 If this option is set, then U-Boot will prevent the environment
1998 variable "splashimage" from being set to a problematic address
1999 (see README.displaying-bmps).
2000 This option is useful for targets where, due to alignment
2001 restrictions, an improperly aligned BMP image will cause a data
2002 abort. If you think you will not have problems with unaligned
2003 accesses (for example because your toolchain prevents them)
2004 there is no need to set this option.
2006 CONFIG_SPLASH_SCREEN_ALIGN
2008 If this option is set the splash image can be freely positioned
2009 on the screen. Environment variable "splashpos" specifies the
2010 position as "x,y". If a positive number is given it is used as
2011 number of pixel from left/top. If a negative number is given it
2012 is used as number of pixel from right/bottom. You can also
2013 specify 'm' for centering the image.
2016 setenv splashpos m,m
2017 => image at center of screen
2019 setenv splashpos 30,20
2020 => image at x = 30 and y = 20
2022 setenv splashpos -10,m
2023 => vertically centered image
2024 at x = dspWidth - bmpWidth - 9
2026 - Gzip compressed BMP image support: CONFIG_VIDEO_BMP_GZIP
2028 If this option is set, additionally to standard BMP
2029 images, gzipped BMP images can be displayed via the
2030 splashscreen support or the bmp command.
2032 - Run length encoded BMP image (RLE8) support: CONFIG_VIDEO_BMP_RLE8
2034 If this option is set, 8-bit RLE compressed BMP images
2035 can be displayed via the splashscreen support or the
2038 - Do compressing for memory range:
2041 If this option is set, it would use zlib deflate method
2042 to compress the specified memory at its best effort.
2044 - Compression support:
2047 Enabled by default to support gzip compressed images.
2051 If this option is set, support for bzip2 compressed
2052 images is included. If not, only uncompressed and gzip
2053 compressed images are supported.
2055 NOTE: the bzip2 algorithm requires a lot of RAM, so
2056 the malloc area (as defined by CONFIG_SYS_MALLOC_LEN) should
2061 If this option is set, support for lzma compressed
2064 Note: The LZMA algorithm adds between 2 and 4KB of code and it
2065 requires an amount of dynamic memory that is given by the
2068 (1846 + 768 << (lc + lp)) * sizeof(uint16)
2070 Where lc and lp stand for, respectively, Literal context bits
2071 and Literal pos bits.
2073 This value is upper-bounded by 14MB in the worst case. Anyway,
2074 for a ~4MB large kernel image, we have lc=3 and lp=0 for a
2075 total amount of (1846 + 768 << (3 + 0)) * 2 = ~41KB... that is
2076 a very small buffer.
2078 Use the lzmainfo tool to determinate the lc and lp values and
2079 then calculate the amount of needed dynamic memory (ensuring
2080 the appropriate CONFIG_SYS_MALLOC_LEN value).
2084 If this option is set, support for LZO compressed images
2090 The address of PHY on MII bus.
2092 CONFIG_PHY_CLOCK_FREQ (ppc4xx)
2094 The clock frequency of the MII bus
2098 If this option is set, support for speed/duplex
2099 detection of gigabit PHY is included.
2101 CONFIG_PHY_RESET_DELAY
2103 Some PHY like Intel LXT971A need extra delay after
2104 reset before any MII register access is possible.
2105 For such PHY, set this option to the usec delay
2106 required. (minimum 300usec for LXT971A)
2108 CONFIG_PHY_CMD_DELAY (ppc4xx)
2110 Some PHY like Intel LXT971A need extra delay after
2111 command issued before MII status register can be read
2116 Define a default value for the IP address to use for
2117 the default Ethernet interface, in case this is not
2118 determined through e.g. bootp.
2119 (Environment variable "ipaddr")
2121 - Server IP address:
2124 Defines a default value for the IP address of a TFTP
2125 server to contact when using the "tftboot" command.
2126 (Environment variable "serverip")
2128 CONFIG_KEEP_SERVERADDR
2130 Keeps the server's MAC address, in the env 'serveraddr'
2131 for passing to bootargs (like Linux's netconsole option)
2133 - Gateway IP address:
2136 Defines a default value for the IP address of the
2137 default router where packets to other networks are
2139 (Environment variable "gatewayip")
2144 Defines a default value for the subnet mask (or
2145 routing prefix) which is used to determine if an IP
2146 address belongs to the local subnet or needs to be
2147 forwarded through a router.
2148 (Environment variable "netmask")
2150 - Multicast TFTP Mode:
2153 Defines whether you want to support multicast TFTP as per
2154 rfc-2090; for example to work with atftp. Lets lots of targets
2155 tftp down the same boot image concurrently. Note: the Ethernet
2156 driver in use must provide a function: mcast() to join/leave a
2159 - BOOTP Recovery Mode:
2160 CONFIG_BOOTP_RANDOM_DELAY
2162 If you have many targets in a network that try to
2163 boot using BOOTP, you may want to avoid that all
2164 systems send out BOOTP requests at precisely the same
2165 moment (which would happen for instance at recovery
2166 from a power failure, when all systems will try to
2167 boot, thus flooding the BOOTP server. Defining
2168 CONFIG_BOOTP_RANDOM_DELAY causes a random delay to be
2169 inserted before sending out BOOTP requests. The
2170 following delays are inserted then:
2172 1st BOOTP request: delay 0 ... 1 sec
2173 2nd BOOTP request: delay 0 ... 2 sec
2174 3rd BOOTP request: delay 0 ... 4 sec
2176 BOOTP requests: delay 0 ... 8 sec
2178 CONFIG_BOOTP_ID_CACHE_SIZE
2180 BOOTP packets are uniquely identified using a 32-bit ID. The
2181 server will copy the ID from client requests to responses and
2182 U-Boot will use this to determine if it is the destination of
2183 an incoming response. Some servers will check that addresses
2184 aren't in use before handing them out (usually using an ARP
2185 ping) and therefore take up to a few hundred milliseconds to
2186 respond. Network congestion may also influence the time it
2187 takes for a response to make it back to the client. If that
2188 time is too long, U-Boot will retransmit requests. In order
2189 to allow earlier responses to still be accepted after these
2190 retransmissions, U-Boot's BOOTP client keeps a small cache of
2191 IDs. The CONFIG_BOOTP_ID_CACHE_SIZE controls the size of this
2192 cache. The default is to keep IDs for up to four outstanding
2193 requests. Increasing this will allow U-Boot to accept offers
2194 from a BOOTP client in networks with unusually high latency.
2196 - DHCP Advanced Options:
2197 You can fine tune the DHCP functionality by defining
2198 CONFIG_BOOTP_* symbols:
2200 CONFIG_BOOTP_SUBNETMASK
2201 CONFIG_BOOTP_GATEWAY
2202 CONFIG_BOOTP_HOSTNAME
2203 CONFIG_BOOTP_NISDOMAIN
2204 CONFIG_BOOTP_BOOTPATH
2205 CONFIG_BOOTP_BOOTFILESIZE
2208 CONFIG_BOOTP_SEND_HOSTNAME
2209 CONFIG_BOOTP_NTPSERVER
2210 CONFIG_BOOTP_TIMEOFFSET
2211 CONFIG_BOOTP_VENDOREX
2212 CONFIG_BOOTP_MAY_FAIL
2214 CONFIG_BOOTP_SERVERIP - TFTP server will be the serverip
2215 environment variable, not the BOOTP server.
2217 CONFIG_BOOTP_MAY_FAIL - If the DHCP server is not found
2218 after the configured retry count, the call will fail
2219 instead of starting over. This can be used to fail over
2220 to Link-local IP address configuration if the DHCP server
2223 CONFIG_BOOTP_DNS2 - If a DHCP client requests the DNS
2224 serverip from a DHCP server, it is possible that more
2225 than one DNS serverip is offered to the client.
2226 If CONFIG_BOOTP_DNS2 is enabled, the secondary DNS
2227 serverip will be stored in the additional environment
2228 variable "dnsip2". The first DNS serverip is always
2229 stored in the variable "dnsip", when CONFIG_BOOTP_DNS
2232 CONFIG_BOOTP_SEND_HOSTNAME - Some DHCP servers are capable
2233 to do a dynamic update of a DNS server. To do this, they
2234 need the hostname of the DHCP requester.
2235 If CONFIG_BOOTP_SEND_HOSTNAME is defined, the content
2236 of the "hostname" environment variable is passed as
2237 option 12 to the DHCP server.
2239 CONFIG_BOOTP_DHCP_REQUEST_DELAY
2241 A 32bit value in microseconds for a delay between
2242 receiving a "DHCP Offer" and sending the "DHCP Request".
2243 This fixes a problem with certain DHCP servers that don't
2244 respond 100% of the time to a "DHCP request". E.g. On an
2245 AT91RM9200 processor running at 180MHz, this delay needed
2246 to be *at least* 15,000 usec before a Windows Server 2003
2247 DHCP server would reply 100% of the time. I recommend at
2248 least 50,000 usec to be safe. The alternative is to hope
2249 that one of the retries will be successful but note that
2250 the DHCP timeout and retry process takes a longer than
2253 - Link-local IP address negotiation:
2254 Negotiate with other link-local clients on the local network
2255 for an address that doesn't require explicit configuration.
2256 This is especially useful if a DHCP server cannot be guaranteed
2257 to exist in all environments that the device must operate.
2259 See doc/README.link-local for more information.
2262 CONFIG_CDP_DEVICE_ID
2264 The device id used in CDP trigger frames.
2266 CONFIG_CDP_DEVICE_ID_PREFIX
2268 A two character string which is prefixed to the MAC address
2273 A printf format string which contains the ascii name of
2274 the port. Normally is set to "eth%d" which sets
2275 eth0 for the first Ethernet, eth1 for the second etc.
2277 CONFIG_CDP_CAPABILITIES
2279 A 32bit integer which indicates the device capabilities;
2280 0x00000010 for a normal host which does not forwards.
2284 An ascii string containing the version of the software.
2288 An ascii string containing the name of the platform.
2292 A 32bit integer sent on the trigger.
2294 CONFIG_CDP_POWER_CONSUMPTION
2296 A 16bit integer containing the power consumption of the
2297 device in .1 of milliwatts.
2299 CONFIG_CDP_APPLIANCE_VLAN_TYPE
2301 A byte containing the id of the VLAN.
2303 - Status LED: CONFIG_STATUS_LED
2305 Several configurations allow to display the current
2306 status using a LED. For instance, the LED will blink
2307 fast while running U-Boot code, stop blinking as
2308 soon as a reply to a BOOTP request was received, and
2309 start blinking slow once the Linux kernel is running
2310 (supported by a status LED driver in the Linux
2311 kernel). Defining CONFIG_STATUS_LED enables this
2317 The status LED can be connected to a GPIO pin.
2318 In such cases, the gpio_led driver can be used as a
2319 status LED backend implementation. Define CONFIG_GPIO_LED
2320 to include the gpio_led driver in the U-Boot binary.
2322 CONFIG_GPIO_LED_INVERTED_TABLE
2323 Some GPIO connected LEDs may have inverted polarity in which
2324 case the GPIO high value corresponds to LED off state and
2325 GPIO low value corresponds to LED on state.
2326 In such cases CONFIG_GPIO_LED_INVERTED_TABLE may be defined
2327 with a list of GPIO LEDs that have inverted polarity.
2329 - CAN Support: CONFIG_CAN_DRIVER
2331 Defining CONFIG_CAN_DRIVER enables CAN driver support
2332 on those systems that support this (optional)
2333 feature, like the TQM8xxL modules.
2335 - I2C Support: CONFIG_SYS_I2C
2337 This enable the NEW i2c subsystem, and will allow you to use
2338 i2c commands at the u-boot command line (as long as you set
2339 CONFIG_CMD_I2C in CONFIG_COMMANDS) and communicate with i2c
2340 based realtime clock chips or other i2c devices. See
2341 common/cmd_i2c.c for a description of the command line
2344 ported i2c driver to the new framework:
2345 - drivers/i2c/soft_i2c.c:
2346 - activate first bus with CONFIG_SYS_I2C_SOFT define
2347 CONFIG_SYS_I2C_SOFT_SPEED and CONFIG_SYS_I2C_SOFT_SLAVE
2348 for defining speed and slave address
2349 - activate second bus with I2C_SOFT_DECLARATIONS2 define
2350 CONFIG_SYS_I2C_SOFT_SPEED_2 and CONFIG_SYS_I2C_SOFT_SLAVE_2
2351 for defining speed and slave address
2352 - activate third bus with I2C_SOFT_DECLARATIONS3 define
2353 CONFIG_SYS_I2C_SOFT_SPEED_3 and CONFIG_SYS_I2C_SOFT_SLAVE_3
2354 for defining speed and slave address
2355 - activate fourth bus with I2C_SOFT_DECLARATIONS4 define
2356 CONFIG_SYS_I2C_SOFT_SPEED_4 and CONFIG_SYS_I2C_SOFT_SLAVE_4
2357 for defining speed and slave address
2359 - drivers/i2c/fsl_i2c.c:
2360 - activate i2c driver with CONFIG_SYS_I2C_FSL
2361 define CONFIG_SYS_FSL_I2C_OFFSET for setting the register
2362 offset CONFIG_SYS_FSL_I2C_SPEED for the i2c speed and
2363 CONFIG_SYS_FSL_I2C_SLAVE for the slave addr of the first
2365 - If your board supports a second fsl i2c bus, define
2366 CONFIG_SYS_FSL_I2C2_OFFSET for the register offset
2367 CONFIG_SYS_FSL_I2C2_SPEED for the speed and
2368 CONFIG_SYS_FSL_I2C2_SLAVE for the slave address of the
2371 - drivers/i2c/tegra_i2c.c:
2372 - activate this driver with CONFIG_SYS_I2C_TEGRA
2373 - This driver adds 4 i2c buses with a fix speed from
2374 100000 and the slave addr 0!
2376 - drivers/i2c/ppc4xx_i2c.c
2377 - activate this driver with CONFIG_SYS_I2C_PPC4XX
2378 - CONFIG_SYS_I2C_PPC4XX_CH0 activate hardware channel 0
2379 - CONFIG_SYS_I2C_PPC4XX_CH1 activate hardware channel 1
2381 - drivers/i2c/i2c_mxc.c
2382 - activate this driver with CONFIG_SYS_I2C_MXC
2383 - define speed for bus 1 with CONFIG_SYS_MXC_I2C1_SPEED
2384 - define slave for bus 1 with CONFIG_SYS_MXC_I2C1_SLAVE
2385 - define speed for bus 2 with CONFIG_SYS_MXC_I2C2_SPEED
2386 - define slave for bus 2 with CONFIG_SYS_MXC_I2C2_SLAVE
2387 - define speed for bus 3 with CONFIG_SYS_MXC_I2C3_SPEED
2388 - define slave for bus 3 with CONFIG_SYS_MXC_I2C3_SLAVE
2389 If those defines are not set, default value is 100000
2390 for speed, and 0 for slave.
2391 - enable bus 3 with CONFIG_SYS_I2C_MXC_I2C3
2392 - enable bus 4 with CONFIG_SYS_I2C_MXC_I2C4
2394 - drivers/i2c/rcar_i2c.c:
2395 - activate this driver with CONFIG_SYS_I2C_RCAR
2396 - This driver adds 4 i2c buses
2398 - CONFIG_SYS_RCAR_I2C0_BASE for setting the register channel 0
2399 - CONFIG_SYS_RCAR_I2C0_SPEED for for the speed channel 0
2400 - CONFIG_SYS_RCAR_I2C1_BASE for setting the register channel 1
2401 - CONFIG_SYS_RCAR_I2C1_SPEED for for the speed channel 1
2402 - CONFIG_SYS_RCAR_I2C2_BASE for setting the register channel 2
2403 - CONFIG_SYS_RCAR_I2C2_SPEED for for the speed channel 2
2404 - CONFIG_SYS_RCAR_I2C3_BASE for setting the register channel 3
2405 - CONFIG_SYS_RCAR_I2C3_SPEED for for the speed channel 3
2406 - CONFIF_SYS_RCAR_I2C_NUM_CONTROLLERS for number of i2c buses
2408 - drivers/i2c/sh_i2c.c:
2409 - activate this driver with CONFIG_SYS_I2C_SH
2410 - This driver adds from 2 to 5 i2c buses
2412 - CONFIG_SYS_I2C_SH_BASE0 for setting the register channel 0
2413 - CONFIG_SYS_I2C_SH_SPEED0 for for the speed channel 0
2414 - CONFIG_SYS_I2C_SH_BASE1 for setting the register channel 1
2415 - CONFIG_SYS_I2C_SH_SPEED1 for for the speed channel 1
2416 - CONFIG_SYS_I2C_SH_BASE2 for setting the register channel 2
2417 - CONFIG_SYS_I2C_SH_SPEED2 for for the speed channel 2
2418 - CONFIG_SYS_I2C_SH_BASE3 for setting the register channel 3
2419 - CONFIG_SYS_I2C_SH_SPEED3 for for the speed channel 3
2420 - CONFIG_SYS_I2C_SH_BASE4 for setting the register channel 4
2421 - CONFIG_SYS_I2C_SH_SPEED4 for for the speed channel 4
2422 - CONFIG_SYS_I2C_SH_BASE5 for setting the register channel 5
2423 - CONFIG_SYS_I2C_SH_SPEED5 for for the speed channel 5
2424 - CONFIG_SYS_I2C_SH_NUM_CONTROLLERS for number of i2c buses
2426 - drivers/i2c/omap24xx_i2c.c
2427 - activate this driver with CONFIG_SYS_I2C_OMAP24XX
2428 - CONFIG_SYS_OMAP24_I2C_SPEED speed channel 0
2429 - CONFIG_SYS_OMAP24_I2C_SLAVE slave addr channel 0
2430 - CONFIG_SYS_OMAP24_I2C_SPEED1 speed channel 1
2431 - CONFIG_SYS_OMAP24_I2C_SLAVE1 slave addr channel 1
2432 - CONFIG_SYS_OMAP24_I2C_SPEED2 speed channel 2
2433 - CONFIG_SYS_OMAP24_I2C_SLAVE2 slave addr channel 2
2434 - CONFIG_SYS_OMAP24_I2C_SPEED3 speed channel 3
2435 - CONFIG_SYS_OMAP24_I2C_SLAVE3 slave addr channel 3
2436 - CONFIG_SYS_OMAP24_I2C_SPEED4 speed channel 4
2437 - CONFIG_SYS_OMAP24_I2C_SLAVE4 slave addr channel 4
2439 - drivers/i2c/zynq_i2c.c
2440 - activate this driver with CONFIG_SYS_I2C_ZYNQ
2441 - set CONFIG_SYS_I2C_ZYNQ_SPEED for speed setting
2442 - set CONFIG_SYS_I2C_ZYNQ_SLAVE for slave addr
2444 - drivers/i2c/s3c24x0_i2c.c:
2445 - activate this driver with CONFIG_SYS_I2C_S3C24X0
2446 - This driver adds i2c buses (11 for Exynos5250, Exynos5420
2447 9 i2c buses for Exynos4 and 1 for S3C24X0 SoCs from Samsung)
2448 with a fix speed from 100000 and the slave addr 0!
2450 - drivers/i2c/ihs_i2c.c
2451 - activate this driver with CONFIG_SYS_I2C_IHS
2452 - CONFIG_SYS_I2C_IHS_CH0 activate hardware channel 0
2453 - CONFIG_SYS_I2C_IHS_SPEED_0 speed channel 0
2454 - CONFIG_SYS_I2C_IHS_SLAVE_0 slave addr channel 0
2455 - CONFIG_SYS_I2C_IHS_CH1 activate hardware channel 1
2456 - CONFIG_SYS_I2C_IHS_SPEED_1 speed channel 1
2457 - CONFIG_SYS_I2C_IHS_SLAVE_1 slave addr channel 1
2458 - CONFIG_SYS_I2C_IHS_CH2 activate hardware channel 2
2459 - CONFIG_SYS_I2C_IHS_SPEED_2 speed channel 2
2460 - CONFIG_SYS_I2C_IHS_SLAVE_2 slave addr channel 2
2461 - CONFIG_SYS_I2C_IHS_CH3 activate hardware channel 3
2462 - CONFIG_SYS_I2C_IHS_SPEED_3 speed channel 3
2463 - CONFIG_SYS_I2C_IHS_SLAVE_3 slave addr channel 3
2467 CONFIG_SYS_NUM_I2C_BUSES
2468 Hold the number of i2c buses you want to use. If you
2469 don't use/have i2c muxes on your i2c bus, this
2470 is equal to CONFIG_SYS_NUM_I2C_ADAPTERS, and you can
2473 CONFIG_SYS_I2C_DIRECT_BUS
2474 define this, if you don't use i2c muxes on your hardware.
2475 if CONFIG_SYS_I2C_MAX_HOPS is not defined or == 0 you can
2478 CONFIG_SYS_I2C_MAX_HOPS
2479 define how many muxes are maximal consecutively connected
2480 on one i2c bus. If you not use i2c muxes, omit this
2483 CONFIG_SYS_I2C_BUSES
2484 hold a list of buses you want to use, only used if
2485 CONFIG_SYS_I2C_DIRECT_BUS is not defined, for example
2486 a board with CONFIG_SYS_I2C_MAX_HOPS = 1 and
2487 CONFIG_SYS_NUM_I2C_BUSES = 9:
2489 CONFIG_SYS_I2C_BUSES {{0, {I2C_NULL_HOP}}, \
2490 {0, {{I2C_MUX_PCA9547, 0x70, 1}}}, \
2491 {0, {{I2C_MUX_PCA9547, 0x70, 2}}}, \
2492 {0, {{I2C_MUX_PCA9547, 0x70, 3}}}, \
2493 {0, {{I2C_MUX_PCA9547, 0x70, 4}}}, \
2494 {0, {{I2C_MUX_PCA9547, 0x70, 5}}}, \
2495 {1, {I2C_NULL_HOP}}, \
2496 {1, {{I2C_MUX_PCA9544, 0x72, 1}}}, \
2497 {1, {{I2C_MUX_PCA9544, 0x72, 2}}}, \
2501 bus 0 on adapter 0 without a mux
2502 bus 1 on adapter 0 with a PCA9547 on address 0x70 port 1
2503 bus 2 on adapter 0 with a PCA9547 on address 0x70 port 2
2504 bus 3 on adapter 0 with a PCA9547 on address 0x70 port 3
2505 bus 4 on adapter 0 with a PCA9547 on address 0x70 port 4
2506 bus 5 on adapter 0 with a PCA9547 on address 0x70 port 5
2507 bus 6 on adapter 1 without a mux
2508 bus 7 on adapter 1 with a PCA9544 on address 0x72 port 1
2509 bus 8 on adapter 1 with a PCA9544 on address 0x72 port 2
2511 If you do not have i2c muxes on your board, omit this define.
2513 - Legacy I2C Support: CONFIG_HARD_I2C
2515 NOTE: It is intended to move drivers to CONFIG_SYS_I2C which
2516 provides the following compelling advantages:
2518 - more than one i2c adapter is usable
2519 - approved multibus support
2520 - better i2c mux support
2522 ** Please consider updating your I2C driver now. **
2524 These enable legacy I2C serial bus commands. Defining
2525 CONFIG_HARD_I2C will include the appropriate I2C driver
2526 for the selected CPU.
2528 This will allow you to use i2c commands at the u-boot
2529 command line (as long as you set CONFIG_CMD_I2C in
2530 CONFIG_COMMANDS) and communicate with i2c based realtime
2531 clock chips. See common/cmd_i2c.c for a description of the
2532 command line interface.
2534 CONFIG_HARD_I2C selects a hardware I2C controller.
2536 There are several other quantities that must also be
2537 defined when you define CONFIG_HARD_I2C.
2539 In both cases you will need to define CONFIG_SYS_I2C_SPEED
2540 to be the frequency (in Hz) at which you wish your i2c bus
2541 to run and CONFIG_SYS_I2C_SLAVE to be the address of this node (ie
2542 the CPU's i2c node address).
2544 Now, the u-boot i2c code for the mpc8xx
2545 (arch/powerpc/cpu/mpc8xx/i2c.c) sets the CPU up as a master node
2546 and so its address should therefore be cleared to 0 (See,
2547 eg, MPC823e User's Manual p.16-473). So, set
2548 CONFIG_SYS_I2C_SLAVE to 0.
2550 CONFIG_SYS_I2C_INIT_MPC5XXX
2552 When a board is reset during an i2c bus transfer
2553 chips might think that the current transfer is still
2554 in progress. Reset the slave devices by sending start
2555 commands until the slave device responds.
2557 That's all that's required for CONFIG_HARD_I2C.
2559 If you use the software i2c interface (CONFIG_SYS_I2C_SOFT)
2560 then the following macros need to be defined (examples are
2561 from include/configs/lwmon.h):
2565 (Optional). Any commands necessary to enable the I2C
2566 controller or configure ports.
2568 eg: #define I2C_INIT (immr->im_cpm.cp_pbdir |= PB_SCL)
2572 (Only for MPC8260 CPU). The I/O port to use (the code
2573 assumes both bits are on the same port). Valid values
2574 are 0..3 for ports A..D.
2578 The code necessary to make the I2C data line active
2579 (driven). If the data line is open collector, this
2582 eg: #define I2C_ACTIVE (immr->im_cpm.cp_pbdir |= PB_SDA)
2586 The code necessary to make the I2C data line tri-stated
2587 (inactive). If the data line is open collector, this
2590 eg: #define I2C_TRISTATE (immr->im_cpm.cp_pbdir &= ~PB_SDA)
2594 Code that returns true if the I2C data line is high,
2597 eg: #define I2C_READ ((immr->im_cpm.cp_pbdat & PB_SDA) != 0)
2601 If <bit> is true, sets the I2C data line high. If it
2602 is false, it clears it (low).
2604 eg: #define I2C_SDA(bit) \
2605 if(bit) immr->im_cpm.cp_pbdat |= PB_SDA; \
2606 else immr->im_cpm.cp_pbdat &= ~PB_SDA
2610 If <bit> is true, sets the I2C clock line high. If it
2611 is false, it clears it (low).
2613 eg: #define I2C_SCL(bit) \
2614 if(bit) immr->im_cpm.cp_pbdat |= PB_SCL; \
2615 else immr->im_cpm.cp_pbdat &= ~PB_SCL
2619 This delay is invoked four times per clock cycle so this
2620 controls the rate of data transfer. The data rate thus
2621 is 1 / (I2C_DELAY * 4). Often defined to be something
2624 #define I2C_DELAY udelay(2)
2626 CONFIG_SOFT_I2C_GPIO_SCL / CONFIG_SOFT_I2C_GPIO_SDA
2628 If your arch supports the generic GPIO framework (asm/gpio.h),
2629 then you may alternatively define the two GPIOs that are to be
2630 used as SCL / SDA. Any of the previous I2C_xxx macros will
2631 have GPIO-based defaults assigned to them as appropriate.
2633 You should define these to the GPIO value as given directly to
2634 the generic GPIO functions.
2636 CONFIG_SYS_I2C_INIT_BOARD
2638 When a board is reset during an i2c bus transfer
2639 chips might think that the current transfer is still
2640 in progress. On some boards it is possible to access
2641 the i2c SCLK line directly, either by using the
2642 processor pin as a GPIO or by having a second pin
2643 connected to the bus. If this option is defined a
2644 custom i2c_init_board() routine in boards/xxx/board.c
2645 is run early in the boot sequence.
2647 CONFIG_SYS_I2C_BOARD_LATE_INIT
2649 An alternative to CONFIG_SYS_I2C_INIT_BOARD. If this option is
2650 defined a custom i2c_board_late_init() routine in
2651 boards/xxx/board.c is run AFTER the operations in i2c_init()
2652 is completed. This callpoint can be used to unreset i2c bus
2653 using CPU i2c controller register accesses for CPUs whose i2c
2654 controller provide such a method. It is called at the end of
2655 i2c_init() to allow i2c_init operations to setup the i2c bus
2656 controller on the CPU (e.g. setting bus speed & slave address).
2658 CONFIG_I2CFAST (PPC405GP|PPC405EP only)
2660 This option enables configuration of bi_iic_fast[] flags
2661 in u-boot bd_info structure based on u-boot environment
2662 variable "i2cfast". (see also i2cfast)
2664 CONFIG_I2C_MULTI_BUS
2666 This option allows the use of multiple I2C buses, each of which
2667 must have a controller. At any point in time, only one bus is
2668 active. To switch to a different bus, use the 'i2c dev' command.
2669 Note that bus numbering is zero-based.
2671 CONFIG_SYS_I2C_NOPROBES
2673 This option specifies a list of I2C devices that will be skipped
2674 when the 'i2c probe' command is issued. If CONFIG_I2C_MULTI_BUS
2675 is set, specify a list of bus-device pairs. Otherwise, specify
2676 a 1D array of device addresses
2679 #undef CONFIG_I2C_MULTI_BUS
2680 #define CONFIG_SYS_I2C_NOPROBES {0x50,0x68}
2682 will skip addresses 0x50 and 0x68 on a board with one I2C bus
2684 #define CONFIG_I2C_MULTI_BUS
2685 #define CONFIG_SYS_I2C_MULTI_NOPROBES {{0,0x50},{0,0x68},{1,0x54}}
2687 will skip addresses 0x50 and 0x68 on bus 0 and address 0x54 on bus 1
2689 CONFIG_SYS_SPD_BUS_NUM
2691 If defined, then this indicates the I2C bus number for DDR SPD.
2692 If not defined, then U-Boot assumes that SPD is on I2C bus 0.
2694 CONFIG_SYS_RTC_BUS_NUM
2696 If defined, then this indicates the I2C bus number for the RTC.
2697 If not defined, then U-Boot assumes that RTC is on I2C bus 0.
2699 CONFIG_SYS_DTT_BUS_NUM
2701 If defined, then this indicates the I2C bus number for the DTT.
2702 If not defined, then U-Boot assumes that DTT is on I2C bus 0.
2704 CONFIG_SYS_I2C_DTT_ADDR:
2706 If defined, specifies the I2C address of the DTT device.
2707 If not defined, then U-Boot uses predefined value for
2708 specified DTT device.
2710 CONFIG_SOFT_I2C_READ_REPEATED_START
2712 defining this will force the i2c_read() function in
2713 the soft_i2c driver to perform an I2C repeated start
2714 between writing the address pointer and reading the
2715 data. If this define is omitted the default behaviour
2716 of doing a stop-start sequence will be used. Most I2C
2717 devices can use either method, but some require one or
2720 - SPI Support: CONFIG_SPI
2722 Enables SPI driver (so far only tested with
2723 SPI EEPROM, also an instance works with Crystal A/D and
2724 D/As on the SACSng board)
2728 Enables the driver for SPI controller on SuperH. Currently
2729 only SH7757 is supported.
2733 Enables extended (16-bit) SPI EEPROM addressing.
2734 (symmetrical to CONFIG_I2C_X)
2738 Enables a software (bit-bang) SPI driver rather than
2739 using hardware support. This is a general purpose
2740 driver that only requires three general I/O port pins
2741 (two outputs, one input) to function. If this is
2742 defined, the board configuration must define several
2743 SPI configuration items (port pins to use, etc). For
2744 an example, see include/configs/sacsng.h.
2748 Enables a hardware SPI driver for general-purpose reads
2749 and writes. As with CONFIG_SOFT_SPI, the board configuration
2750 must define a list of chip-select function pointers.
2751 Currently supported on some MPC8xxx processors. For an
2752 example, see include/configs/mpc8349emds.h.
2756 Enables the driver for the SPI controllers on i.MX and MXC
2757 SoCs. Currently i.MX31/35/51 are supported.
2759 CONFIG_SYS_SPI_MXC_WAIT
2760 Timeout for waiting until spi transfer completed.
2761 default: (CONFIG_SYS_HZ/100) /* 10 ms */
2763 - FPGA Support: CONFIG_FPGA
2765 Enables FPGA subsystem.
2767 CONFIG_FPGA_<vendor>
2769 Enables support for specific chip vendors.
2772 CONFIG_FPGA_<family>
2774 Enables support for FPGA family.
2775 (SPARTAN2, SPARTAN3, VIRTEX2, CYCLONE2, ACEX1K, ACEX)
2779 Specify the number of FPGA devices to support.
2781 CONFIG_CMD_FPGA_LOADMK
2783 Enable support for fpga loadmk command
2785 CONFIG_CMD_FPGA_LOADP
2787 Enable support for fpga loadp command - load partial bitstream
2789 CONFIG_CMD_FPGA_LOADBP
2791 Enable support for fpga loadbp command - load partial bitstream
2794 CONFIG_SYS_FPGA_PROG_FEEDBACK
2796 Enable printing of hash marks during FPGA configuration.
2798 CONFIG_SYS_FPGA_CHECK_BUSY
2800 Enable checks on FPGA configuration interface busy
2801 status by the configuration function. This option
2802 will require a board or device specific function to
2807 If defined, a function that provides delays in the FPGA
2808 configuration driver.
2810 CONFIG_SYS_FPGA_CHECK_CTRLC
2811 Allow Control-C to interrupt FPGA configuration
2813 CONFIG_SYS_FPGA_CHECK_ERROR
2815 Check for configuration errors during FPGA bitfile
2816 loading. For example, abort during Virtex II
2817 configuration if the INIT_B line goes low (which
2818 indicated a CRC error).
2820 CONFIG_SYS_FPGA_WAIT_INIT
2822 Maximum time to wait for the INIT_B line to de-assert
2823 after PROB_B has been de-asserted during a Virtex II
2824 FPGA configuration sequence. The default time is 500
2827 CONFIG_SYS_FPGA_WAIT_BUSY
2829 Maximum time to wait for BUSY to de-assert during
2830 Virtex II FPGA configuration. The default is 5 ms.
2832 CONFIG_SYS_FPGA_WAIT_CONFIG
2834 Time to wait after FPGA configuration. The default is
2837 - Configuration Management:
2840 Some SoCs need special image types (e.g. U-Boot binary
2841 with a special header) as build targets. By defining
2842 CONFIG_BUILD_TARGET in the SoC / board header, this
2843 special image will be automatically built upon calling
2848 If defined, this string will be added to the U-Boot
2849 version information (U_BOOT_VERSION)
2851 - Vendor Parameter Protection:
2853 U-Boot considers the values of the environment
2854 variables "serial#" (Board Serial Number) and
2855 "ethaddr" (Ethernet Address) to be parameters that
2856 are set once by the board vendor / manufacturer, and
2857 protects these variables from casual modification by
2858 the user. Once set, these variables are read-only,
2859 and write or delete attempts are rejected. You can
2860 change this behaviour:
2862 If CONFIG_ENV_OVERWRITE is #defined in your config
2863 file, the write protection for vendor parameters is
2864 completely disabled. Anybody can change or delete
2867 Alternatively, if you define _both_ an ethaddr in the
2868 default env _and_ CONFIG_OVERWRITE_ETHADDR_ONCE, a default
2869 Ethernet address is installed in the environment,
2870 which can be changed exactly ONCE by the user. [The
2871 serial# is unaffected by this, i. e. it remains
2874 The same can be accomplished in a more flexible way
2875 for any variable by configuring the type of access
2876 to allow for those variables in the ".flags" variable
2877 or define CONFIG_ENV_FLAGS_LIST_STATIC.
2882 Define this variable to enable the reservation of
2883 "protected RAM", i. e. RAM which is not overwritten
2884 by U-Boot. Define CONFIG_PRAM to hold the number of
2885 kB you want to reserve for pRAM. You can overwrite
2886 this default value by defining an environment
2887 variable "pram" to the number of kB you want to
2888 reserve. Note that the board info structure will
2889 still show the full amount of RAM. If pRAM is
2890 reserved, a new environment variable "mem" will
2891 automatically be defined to hold the amount of
2892 remaining RAM in a form that can be passed as boot
2893 argument to Linux, for instance like that:
2895 setenv bootargs ... mem=\${mem}
2898 This way you can tell Linux not to use this memory,
2899 either, which results in a memory region that will
2900 not be affected by reboots.
2902 *WARNING* If your board configuration uses automatic
2903 detection of the RAM size, you must make sure that
2904 this memory test is non-destructive. So far, the
2905 following board configurations are known to be
2908 IVMS8, IVML24, SPD8xx, TQM8xxL,
2909 HERMES, IP860, RPXlite, LWMON,
2912 - Access to physical memory region (> 4GB)
2913 Some basic support is provided for operations on memory not
2914 normally accessible to U-Boot - e.g. some architectures
2915 support access to more than 4GB of memory on 32-bit
2916 machines using physical address extension or similar.
2917 Define CONFIG_PHYSMEM to access this basic support, which
2918 currently only supports clearing the memory.
2923 Define this variable to stop the system in case of a
2924 fatal error, so that you have to reset it manually.
2925 This is probably NOT a good idea for an embedded
2926 system where you want the system to reboot
2927 automatically as fast as possible, but it may be
2928 useful during development since you can try to debug
2929 the conditions that lead to the situation.
2931 CONFIG_NET_RETRY_COUNT
2933 This variable defines the number of retries for
2934 network operations like ARP, RARP, TFTP, or BOOTP
2935 before giving up the operation. If not defined, a
2936 default value of 5 is used.
2940 Timeout waiting for an ARP reply in milliseconds.
2944 Timeout in milliseconds used in NFS protocol.
2945 If you encounter "ERROR: Cannot umount" in nfs command,
2946 try longer timeout such as
2947 #define CONFIG_NFS_TIMEOUT 10000UL
2949 - Command Interpreter:
2950 CONFIG_AUTO_COMPLETE
2952 Enable auto completion of commands using TAB.
2954 CONFIG_SYS_PROMPT_HUSH_PS2
2956 This defines the secondary prompt string, which is
2957 printed when the command interpreter needs more input
2958 to complete a command. Usually "> ".
2962 In the current implementation, the local variables
2963 space and global environment variables space are
2964 separated. Local variables are those you define by
2965 simply typing `name=value'. To access a local
2966 variable later on, you have write `$name' or
2967 `${name}'; to execute the contents of a variable
2968 directly type `$name' at the command prompt.
2970 Global environment variables are those you use
2971 setenv/printenv to work with. To run a command stored
2972 in such a variable, you need to use the run command,
2973 and you must not use the '$' sign to access them.
2975 To store commands and special characters in a
2976 variable, please use double quotation marks
2977 surrounding the whole text of the variable, instead
2978 of the backslashes before semicolons and special
2981 - Command Line Editing and History:
2982 CONFIG_CMDLINE_EDITING
2984 Enable editing and History functions for interactive
2985 command line input operations
2987 - Default Environment:
2988 CONFIG_EXTRA_ENV_SETTINGS
2990 Define this to contain any number of null terminated
2991 strings (variable = value pairs) that will be part of
2992 the default environment compiled into the boot image.
2994 For example, place something like this in your
2995 board's config file:
2997 #define CONFIG_EXTRA_ENV_SETTINGS \
3001 Warning: This method is based on knowledge about the
3002 internal format how the environment is stored by the
3003 U-Boot code. This is NOT an official, exported
3004 interface! Although it is unlikely that this format
3005 will change soon, there is no guarantee either.
3006 You better know what you are doing here.
3008 Note: overly (ab)use of the default environment is
3009 discouraged. Make sure to check other ways to preset
3010 the environment like the "source" command or the
3013 CONFIG_ENV_VARS_UBOOT_CONFIG
3015 Define this in order to add variables describing the
3016 U-Boot build configuration to the default environment.
3017 These will be named arch, cpu, board, vendor, and soc.
3019 Enabling this option will cause the following to be defined:
3027 CONFIG_ENV_VARS_UBOOT_RUNTIME_CONFIG
3029 Define this in order to add variables describing certain
3030 run-time determined information about the hardware to the
3031 environment. These will be named board_name, board_rev.
3033 CONFIG_DELAY_ENVIRONMENT
3035 Normally the environment is loaded when the board is
3036 initialised so that it is available to U-Boot. This inhibits
3037 that so that the environment is not available until
3038 explicitly loaded later by U-Boot code. With CONFIG_OF_CONTROL
3039 this is instead controlled by the value of
3040 /config/load-environment.
3042 - DataFlash Support:
3043 CONFIG_HAS_DATAFLASH
3045 Defining this option enables DataFlash features and
3046 allows to read/write in Dataflash via the standard
3049 - Serial Flash support
3052 Defining this option enables SPI flash commands
3053 'sf probe/read/write/erase/update'.
3055 Usage requires an initial 'probe' to define the serial
3056 flash parameters, followed by read/write/erase/update
3059 The following defaults may be provided by the platform
3060 to handle the common case when only a single serial
3061 flash is present on the system.
3063 CONFIG_SF_DEFAULT_BUS Bus identifier
3064 CONFIG_SF_DEFAULT_CS Chip-select
3065 CONFIG_SF_DEFAULT_MODE (see include/spi.h)
3066 CONFIG_SF_DEFAULT_SPEED in Hz
3070 Define this option to include a destructive SPI flash
3073 CONFIG_SPI_FLASH_BAR Ban/Extended Addr Reg
3075 Define this option to use the Bank addr/Extended addr
3076 support on SPI flashes which has size > 16Mbytes.
3078 CONFIG_SF_DUAL_FLASH Dual flash memories
3080 Define this option to use dual flash support where two flash
3081 memories can be connected with a given cs line.
3082 Currently Xilinx Zynq qspi supports these type of connections.
3084 - SystemACE Support:
3087 Adding this option adds support for Xilinx SystemACE
3088 chips attached via some sort of local bus. The address
3089 of the chip must also be defined in the
3090 CONFIG_SYS_SYSTEMACE_BASE macro. For example:
3092 #define CONFIG_SYSTEMACE
3093 #define CONFIG_SYS_SYSTEMACE_BASE 0xf0000000
3095 When SystemACE support is added, the "ace" device type
3096 becomes available to the fat commands, i.e. fatls.
3098 - TFTP Fixed UDP Port:
3101 If this is defined, the environment variable tftpsrcp
3102 is used to supply the TFTP UDP source port value.
3103 If tftpsrcp isn't defined, the normal pseudo-random port
3104 number generator is used.
3106 Also, the environment variable tftpdstp is used to supply
3107 the TFTP UDP destination port value. If tftpdstp isn't
3108 defined, the normal port 69 is used.
3110 The purpose for tftpsrcp is to allow a TFTP server to
3111 blindly start the TFTP transfer using the pre-configured
3112 target IP address and UDP port. This has the effect of
3113 "punching through" the (Windows XP) firewall, allowing
3114 the remainder of the TFTP transfer to proceed normally.
3115 A better solution is to properly configure the firewall,
3116 but sometimes that is not allowed.
3121 This enables a generic 'hash' command which can produce
3122 hashes / digests from a few algorithms (e.g. SHA1, SHA256).
3126 Enable the hash verify command (hash -v). This adds to code
3129 CONFIG_SHA1 - This option enables support of hashing using SHA1
3130 algorithm. The hash is calculated in software.
3131 CONFIG_SHA256 - This option enables support of hashing using
3132 SHA256 algorithm. The hash is calculated in software.
3133 CONFIG_SHA_HW_ACCEL - This option enables hardware acceleration
3134 for SHA1/SHA256 hashing.
3135 This affects the 'hash' command and also the
3136 hash_lookup_algo() function.
3137 CONFIG_SHA_PROG_HW_ACCEL - This option enables
3138 hardware-acceleration for SHA1/SHA256 progressive hashing.
3139 Data can be streamed in a block at a time and the hashing
3140 is performed in hardware.
3142 Note: There is also a sha1sum command, which should perhaps
3143 be deprecated in favour of 'hash sha1'.
3145 - Freescale i.MX specific commands:
3146 CONFIG_CMD_HDMIDETECT
3147 This enables 'hdmidet' command which returns true if an
3148 HDMI monitor is detected. This command is i.MX 6 specific.
3151 This enables the 'bmode' (bootmode) command for forcing
3152 a boot from specific media.
3154 This is useful for forcing the ROM's usb downloader to
3155 activate upon a watchdog reset which is nice when iterating
3156 on U-Boot. Using the reset button or running bmode normal
3157 will set it back to normal. This command currently
3158 supports i.MX53 and i.MX6.
3163 This enables the RSA algorithm used for FIT image verification
3164 in U-Boot. See doc/uImage.FIT/signature.txt for more information.
3166 The Modular Exponentiation algorithm in RSA is implemented using
3167 driver model. So CONFIG_DM needs to be enabled by default for this
3168 library to function.
3170 The signing part is build into mkimage regardless of this
3171 option. The software based modular exponentiation is built into
3172 mkimage irrespective of this option.
3174 - bootcount support:
3175 CONFIG_BOOTCOUNT_LIMIT
3177 This enables the bootcounter support, see:
3178 http://www.denx.de/wiki/DULG/UBootBootCountLimit
3181 enable special bootcounter support on at91sam9xe based boards.
3183 enable special bootcounter support on blackfin based boards.
3185 enable special bootcounter support on da850 based boards.
3186 CONFIG_BOOTCOUNT_RAM
3187 enable support for the bootcounter in RAM
3188 CONFIG_BOOTCOUNT_I2C
3189 enable support for the bootcounter on an i2c (like RTC) device.
3190 CONFIG_SYS_I2C_RTC_ADDR = i2c chip address
3191 CONFIG_SYS_BOOTCOUNT_ADDR = i2c addr which is used for
3193 CONFIG_BOOTCOUNT_ALEN = address len
3195 - Show boot progress:
3196 CONFIG_SHOW_BOOT_PROGRESS
3198 Defining this option allows to add some board-
3199 specific code (calling a user-provided function
3200 "show_boot_progress(int)") that enables you to show
3201 the system's boot progress on some display (for
3202 example, some LED's) on your board. At the moment,
3203 the following checkpoints are implemented:
3206 Legacy uImage format:
3209 1 common/cmd_bootm.c before attempting to boot an image
3210 -1 common/cmd_bootm.c Image header has bad magic number
3211 2 common/cmd_bootm.c Image header has correct magic number
3212 -2 common/cmd_bootm.c Image header has bad checksum
3213 3 common/cmd_bootm.c Image header has correct checksum
3214 -3 common/cmd_bootm.c Image data has bad checksum
3215 4 common/cmd_bootm.c Image data has correct checksum
3216 -4 common/cmd_bootm.c Image is for unsupported architecture
3217 5 common/cmd_bootm.c Architecture check OK
3218 -5 common/cmd_bootm.c Wrong Image Type (not kernel, multi)
3219 6 common/cmd_bootm.c Image Type check OK
3220 -6 common/cmd_bootm.c gunzip uncompression error
3221 -7 common/cmd_bootm.c Unimplemented compression type
3222 7 common/cmd_bootm.c Uncompression OK
3223 8 common/cmd_bootm.c No uncompress/copy overwrite error
3224 -9 common/cmd_bootm.c Unsupported OS (not Linux, BSD, VxWorks, QNX)
3226 9 common/image.c Start initial ramdisk verification
3227 -10 common/image.c Ramdisk header has bad magic number
3228 -11 common/image.c Ramdisk header has bad checksum
3229 10 common/image.c Ramdisk header is OK
3230 -12 common/image.c Ramdisk data has bad checksum
3231 11 common/image.c Ramdisk data has correct checksum
3232 12 common/image.c Ramdisk verification complete, start loading
3233 -13 common/image.c Wrong Image Type (not PPC Linux ramdisk)
3234 13 common/image.c Start multifile image verification
3235 14 common/image.c No initial ramdisk, no multifile, continue.
3237 15 arch/<arch>/lib/bootm.c All preparation done, transferring control to OS
3239 -30 arch/powerpc/lib/board.c Fatal error, hang the system
3240 -31 post/post.c POST test failed, detected by post_output_backlog()
3241 -32 post/post.c POST test failed, detected by post_run_single()
3243 34 common/cmd_doc.c before loading a Image from a DOC device
3244 -35 common/cmd_doc.c Bad usage of "doc" command
3245 35 common/cmd_doc.c correct usage of "doc" command
3246 -36 common/cmd_doc.c No boot device
3247 36 common/cmd_doc.c correct boot device
3248 -37 common/cmd_doc.c Unknown Chip ID on boot device
3249 37 common/cmd_doc.c correct chip ID found, device available
3250 -38 common/cmd_doc.c Read Error on boot device
3251 38 common/cmd_doc.c reading Image header from DOC device OK
3252 -39 common/cmd_doc.c Image header has bad magic number
3253 39 common/cmd_doc.c Image header has correct magic number
3254 -40 common/cmd_doc.c Error reading Image from DOC device
3255 40 common/cmd_doc.c Image header has correct magic number
3256 41 common/cmd_ide.c before loading a Image from a IDE device
3257 -42 common/cmd_ide.c Bad usage of "ide" command
3258 42 common/cmd_ide.c correct usage of "ide" command
3259 -43 common/cmd_ide.c No boot device
3260 43 common/cmd_ide.c boot device found
3261 -44 common/cmd_ide.c Device not available
3262 44 common/cmd_ide.c Device available
3263 -45 common/cmd_ide.c wrong partition selected
3264 45 common/cmd_ide.c partition selected
3265 -46 common/cmd_ide.c Unknown partition table
3266 46 common/cmd_ide.c valid partition table found
3267 -47 common/cmd_ide.c Invalid partition type
3268 47 common/cmd_ide.c correct partition type
3269 -48 common/cmd_ide.c Error reading Image Header on boot device
3270 48 common/cmd_ide.c reading Image Header from IDE device OK
3271 -49 common/cmd_ide.c Image header has bad magic number
3272 49 common/cmd_ide.c Image header has correct magic number
3273 -50 common/cmd_ide.c Image header has bad checksum
3274 50 common/cmd_ide.c Image header has correct checksum
3275 -51 common/cmd_ide.c Error reading Image from IDE device
3276 51 common/cmd_ide.c reading Image from IDE device OK
3277 52 common/cmd_nand.c before loading a Image from a NAND device
3278 -53 common/cmd_nand.c Bad usage of "nand" command
3279 53 common/cmd_nand.c correct usage of "nand" command
3280 -54 common/cmd_nand.c No boot device
3281 54 common/cmd_nand.c boot device found
3282 -55 common/cmd_nand.c Unknown Chip ID on boot device
3283 55 common/cmd_nand.c correct chip ID found, device available
3284 -56 common/cmd_nand.c Error reading Image Header on boot device
3285 56 common/cmd_nand.c reading Image Header from NAND device OK
3286 -57 common/cmd_nand.c Image header has bad magic number
3287 57 common/cmd_nand.c Image header has correct magic number
3288 -58 common/cmd_nand.c Error reading Image from NAND device
3289 58 common/cmd_nand.c reading Image from NAND device OK
3291 -60 common/env_common.c Environment has a bad CRC, using default
3293 64 net/eth.c starting with Ethernet configuration.
3294 -64 net/eth.c no Ethernet found.
3295 65 net/eth.c Ethernet found.
3297 -80 common/cmd_net.c usage wrong
3298 80 common/cmd_net.c before calling net_loop()
3299 -81 common/cmd_net.c some error in net_loop() occurred
3300 81 common/cmd_net.c net_loop() back without error
3301 -82 common/cmd_net.c size == 0 (File with size 0 loaded)
3302 82 common/cmd_net.c trying automatic boot
3303 83 common/cmd_net.c running "source" command
3304 -83 common/cmd_net.c some error in automatic boot or "source" command
3305 84 common/cmd_net.c end without errors
3310 100 common/cmd_bootm.c Kernel FIT Image has correct format
3311 -100 common/cmd_bootm.c Kernel FIT Image has incorrect format
3312 101 common/cmd_bootm.c No Kernel subimage unit name, using configuration
3313 -101 common/cmd_bootm.c Can't get configuration for kernel subimage
3314 102 common/cmd_bootm.c Kernel unit name specified
3315 -103 common/cmd_bootm.c Can't get kernel subimage node offset
3316 103 common/cmd_bootm.c Found configuration node
3317 104 common/cmd_bootm.c Got kernel subimage node offset
3318 -104 common/cmd_bootm.c Kernel subimage hash verification failed
3319 105 common/cmd_bootm.c Kernel subimage hash verification OK
3320 -105 common/cmd_bootm.c Kernel subimage is for unsupported architecture
3321 106 common/cmd_bootm.c Architecture check OK
3322 -106 common/cmd_bootm.c Kernel subimage has wrong type
3323 107 common/cmd_bootm.c Kernel subimage type OK
3324 -107 common/cmd_bootm.c Can't get kernel subimage data/size
3325 108 common/cmd_bootm.c Got kernel subimage data/size
3326 -108 common/cmd_bootm.c Wrong image type (not legacy, FIT)
3327 -109 common/cmd_bootm.c Can't get kernel subimage type
3328 -110 common/cmd_bootm.c Can't get kernel subimage comp
3329 -111 common/cmd_bootm.c Can't get kernel subimage os
3330 -112 common/cmd_bootm.c Can't get kernel subimage load address
3331 -113 common/cmd_bootm.c Image uncompress/copy overwrite error
3333 120 common/image.c Start initial ramdisk verification
3334 -120 common/image.c Ramdisk FIT image has incorrect format
3335 121 common/image.c Ramdisk FIT image has correct format
3336 122 common/image.c No ramdisk subimage unit name, using configuration
3337 -122 common/image.c Can't get configuration for ramdisk subimage
3338 123 common/image.c Ramdisk unit name specified
3339 -124 common/image.c Can't get ramdisk subimage node offset
3340 125 common/image.c Got ramdisk subimage node offset
3341 -125 common/image.c Ramdisk subimage hash verification failed
3342 126 common/image.c Ramdisk subimage hash verification OK
3343 -126 common/image.c Ramdisk subimage for unsupported architecture
3344 127 common/image.c Architecture check OK
3345 -127 common/image.c Can't get ramdisk subimage data/size
3346 128 common/image.c Got ramdisk subimage data/size
3347 129 common/image.c Can't get ramdisk load address
3348 -129 common/image.c Got ramdisk load address
3350 -130 common/cmd_doc.c Incorrect FIT image format
3351 131 common/cmd_doc.c FIT image format OK
3353 -140 common/cmd_ide.c Incorrect FIT image format
3354 141 common/cmd_ide.c FIT image format OK
3356 -150 common/cmd_nand.c Incorrect FIT image format
3357 151 common/cmd_nand.c FIT image format OK
3359 - legacy image format:
3360 CONFIG_IMAGE_FORMAT_LEGACY
3361 enables the legacy image format support in U-Boot.
3364 enabled if CONFIG_FIT_SIGNATURE is not defined.
3366 CONFIG_DISABLE_IMAGE_LEGACY
3367 disable the legacy image format
3369 This define is introduced, as the legacy image format is
3370 enabled per default for backward compatibility.
3372 - FIT image support:
3374 Enable support for the FIT uImage format.
3376 CONFIG_FIT_BEST_MATCH
3377 When no configuration is explicitly selected, default to the
3378 one whose fdt's compatibility field best matches that of
3379 U-Boot itself. A match is considered "best" if it matches the
3380 most specific compatibility entry of U-Boot's fdt's root node.
3381 The order of entries in the configuration's fdt is ignored.
3383 CONFIG_FIT_SIGNATURE
3384 This option enables signature verification of FIT uImages,
3385 using a hash signed and verified using RSA. If
3386 CONFIG_SHA_PROG_HW_ACCEL is defined, i.e support for progressive
3387 hashing is available using hardware, RSA library will use it.
3388 See doc/uImage.FIT/signature.txt for more details.
3390 WARNING: When relying on signed FIT images with required
3391 signature check the legacy image format is default
3392 disabled. If a board need legacy image format support
3393 enable this through CONFIG_IMAGE_FORMAT_LEGACY
3395 CONFIG_FIT_DISABLE_SHA256
3396 Supporting SHA256 hashes has quite an impact on binary size.
3397 For constrained systems sha256 hash support can be disabled
3400 - Standalone program support:
3401 CONFIG_STANDALONE_LOAD_ADDR
3403 This option defines a board specific value for the
3404 address where standalone program gets loaded, thus
3405 overwriting the architecture dependent default
3408 - Frame Buffer Address:
3411 Define CONFIG_FB_ADDR if you want to use specific
3412 address for frame buffer. This is typically the case
3413 when using a graphics controller has separate video
3414 memory. U-Boot will then place the frame buffer at
3415 the given address instead of dynamically reserving it
3416 in system RAM by calling lcd_setmem(), which grabs
3417 the memory for the frame buffer depending on the
3418 configured panel size.
3420 Please see board_init_f function.
3422 - Automatic software updates via TFTP server
3424 CONFIG_UPDATE_TFTP_CNT_MAX
3425 CONFIG_UPDATE_TFTP_MSEC_MAX
3427 These options enable and control the auto-update feature;
3428 for a more detailed description refer to doc/README.update.
3430 - MTD Support (mtdparts command, UBI support)
3433 Adds the MTD device infrastructure from the Linux kernel.
3434 Needed for mtdparts command support.
3436 CONFIG_MTD_PARTITIONS
3438 Adds the MTD partitioning infrastructure from the Linux
3439 kernel. Needed for UBI support.
3444 Adds commands for interacting with MTD partitions formatted
3445 with the UBI flash translation layer
3447 Requires also defining CONFIG_RBTREE
3449 CONFIG_UBI_SILENCE_MSG
3451 Make the verbose messages from UBI stop printing. This leaves
3452 warnings and errors enabled.
3455 CONFIG_MTD_UBI_WL_THRESHOLD
3456 This parameter defines the maximum difference between the highest
3457 erase counter value and the lowest erase counter value of eraseblocks
3458 of UBI devices. When this threshold is exceeded, UBI starts performing
3459 wear leveling by means of moving data from eraseblock with low erase
3460 counter to eraseblocks with high erase counter.
3462 The default value should be OK for SLC NAND flashes, NOR flashes and
3463 other flashes which have eraseblock life-cycle 100000 or more.
3464 However, in case of MLC NAND flashes which typically have eraseblock
3465 life-cycle less than 10000, the threshold should be lessened (e.g.,
3466 to 128 or 256, although it does not have to be power of 2).
3470 CONFIG_MTD_UBI_BEB_LIMIT
3471 This option specifies the maximum bad physical eraseblocks UBI
3472 expects on the MTD device (per 1024 eraseblocks). If the
3473 underlying flash does not admit of bad eraseblocks (e.g. NOR
3474 flash), this value is ignored.
3476 NAND datasheets often specify the minimum and maximum NVM
3477 (Number of Valid Blocks) for the flashes' endurance lifetime.
3478 The maximum expected bad eraseblocks per 1024 eraseblocks
3479 then can be calculated as "1024 * (1 - MinNVB / MaxNVB)",
3480 which gives 20 for most NANDs (MaxNVB is basically the total
3481 count of eraseblocks on the chip).
3483 To put it differently, if this value is 20, UBI will try to
3484 reserve about 1.9% of physical eraseblocks for bad blocks
3485 handling. And that will be 1.9% of eraseblocks on the entire
3486 NAND chip, not just the MTD partition UBI attaches. This means
3487 that if you have, say, a NAND flash chip admits maximum 40 bad
3488 eraseblocks, and it is split on two MTD partitions of the same
3489 size, UBI will reserve 40 eraseblocks when attaching a
3494 CONFIG_MTD_UBI_FASTMAP
3495 Fastmap is a mechanism which allows attaching an UBI device
3496 in nearly constant time. Instead of scanning the whole MTD device it
3497 only has to locate a checkpoint (called fastmap) on the device.
3498 The on-flash fastmap contains all information needed to attach
3499 the device. Using fastmap makes only sense on large devices where
3500 attaching by scanning takes long. UBI will not automatically install
3501 a fastmap on old images, but you can set the UBI parameter
3502 CONFIG_MTD_UBI_FASTMAP_AUTOCONVERT to 1 if you want so. Please note
3503 that fastmap-enabled images are still usable with UBI implementations
3504 without fastmap support. On typical flash devices the whole fastmap
3505 fits into one PEB. UBI will reserve PEBs to hold two fastmaps.
3507 CONFIG_MTD_UBI_FASTMAP_AUTOCONVERT
3508 Set this parameter to enable fastmap automatically on images
3515 Adds commands for interacting with UBI volumes formatted as
3516 UBIFS. UBIFS is read-only in u-boot.
3518 Requires UBI support as well as CONFIG_LZO
3520 CONFIG_UBIFS_SILENCE_MSG
3522 Make the verbose messages from UBIFS stop printing. This leaves
3523 warnings and errors enabled.
3527 Enable building of SPL globally.
3530 LDSCRIPT for linking the SPL binary.
3532 CONFIG_SPL_MAX_FOOTPRINT
3533 Maximum size in memory allocated to the SPL, BSS included.
3534 When defined, the linker checks that the actual memory
3535 used by SPL from _start to __bss_end does not exceed it.
3536 CONFIG_SPL_MAX_FOOTPRINT and CONFIG_SPL_BSS_MAX_SIZE
3537 must not be both defined at the same time.
3540 Maximum size of the SPL image (text, data, rodata, and
3541 linker lists sections), BSS excluded.
3542 When defined, the linker checks that the actual size does
3545 CONFIG_SPL_TEXT_BASE
3546 TEXT_BASE for linking the SPL binary.
3548 CONFIG_SPL_RELOC_TEXT_BASE
3549 Address to relocate to. If unspecified, this is equal to
3550 CONFIG_SPL_TEXT_BASE (i.e. no relocation is done).
3552 CONFIG_SPL_BSS_START_ADDR
3553 Link address for the BSS within the SPL binary.
3555 CONFIG_SPL_BSS_MAX_SIZE
3556 Maximum size in memory allocated to the SPL BSS.
3557 When defined, the linker checks that the actual memory used
3558 by SPL from __bss_start to __bss_end does not exceed it.
3559 CONFIG_SPL_MAX_FOOTPRINT and CONFIG_SPL_BSS_MAX_SIZE
3560 must not be both defined at the same time.
3563 Adress of the start of the stack SPL will use
3565 CONFIG_SPL_PANIC_ON_RAW_IMAGE
3566 When defined, SPL will panic() if the image it has
3567 loaded does not have a signature.
3568 Defining this is useful when code which loads images
3569 in SPL cannot guarantee that absolutely all read errors
3571 An example is the LPC32XX MLC NAND driver, which will
3572 consider that a completely unreadable NAND block is bad,
3573 and thus should be skipped silently.
3575 CONFIG_SPL_RELOC_STACK
3576 Adress of the start of the stack SPL will use after
3577 relocation. If unspecified, this is equal to
3580 CONFIG_SYS_SPL_MALLOC_START
3581 Starting address of the malloc pool used in SPL.
3583 CONFIG_SYS_SPL_MALLOC_SIZE
3584 The size of the malloc pool used in SPL.
3586 CONFIG_SPL_FRAMEWORK
3587 Enable the SPL framework under common/. This framework
3588 supports MMC, NAND and YMODEM loading of U-Boot and NAND
3589 NAND loading of the Linux Kernel.
3592 Enable booting directly to an OS from SPL.
3593 See also: doc/README.falcon
3595 CONFIG_SPL_DISPLAY_PRINT
3596 For ARM, enable an optional function to print more information
3597 about the running system.
3599 CONFIG_SPL_INIT_MINIMAL
3600 Arch init code should be built for a very small image
3602 CONFIG_SPL_LIBCOMMON_SUPPORT
3603 Support for common/libcommon.o in SPL binary
3605 CONFIG_SPL_LIBDISK_SUPPORT
3606 Support for disk/libdisk.o in SPL binary
3608 CONFIG_SPL_I2C_SUPPORT
3609 Support for drivers/i2c/libi2c.o in SPL binary
3611 CONFIG_SPL_GPIO_SUPPORT
3612 Support for drivers/gpio/libgpio.o in SPL binary
3614 CONFIG_SPL_MMC_SUPPORT
3615 Support for drivers/mmc/libmmc.o in SPL binary
3617 CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR,
3618 CONFIG_SYS_U_BOOT_MAX_SIZE_SECTORS,
3619 Address and partition on the MMC to load U-Boot from
3620 when the MMC is being used in raw mode.
3622 CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_PARTITION
3623 Partition on the MMC to load U-Boot from when the MMC is being
3626 CONFIG_SYS_MMCSD_RAW_MODE_KERNEL_SECTOR
3627 Sector to load kernel uImage from when MMC is being
3628 used in raw mode (for Falcon mode)
3630 CONFIG_SYS_MMCSD_RAW_MODE_ARGS_SECTOR,
3631 CONFIG_SYS_MMCSD_RAW_MODE_ARGS_SECTORS
3632 Sector and number of sectors to load kernel argument
3633 parameters from when MMC is being used in raw mode
3636 CONFIG_SYS_MMCSD_FS_BOOT_PARTITION
3637 Partition on the MMC to load U-Boot from when the MMC is being
3640 CONFIG_SPL_FAT_SUPPORT
3641 Support for fs/fat/libfat.o in SPL binary
3643 CONFIG_SPL_EXT_SUPPORT
3644 Support for EXT filesystem in SPL binary
3646 CONFIG_SPL_FS_LOAD_PAYLOAD_NAME
3647 Filename to read to load U-Boot when reading from filesystem
3649 CONFIG_SPL_FS_LOAD_KERNEL_NAME
3650 Filename to read to load kernel uImage when reading
3651 from filesystem (for Falcon mode)
3653 CONFIG_SPL_FS_LOAD_ARGS_NAME
3654 Filename to read to load kernel argument parameters
3655 when reading from filesystem (for Falcon mode)
3657 CONFIG_SPL_MPC83XX_WAIT_FOR_NAND
3658 Set this for NAND SPL on PPC mpc83xx targets, so that
3659 start.S waits for the rest of the SPL to load before
3660 continuing (the hardware starts execution after just
3661 loading the first page rather than the full 4K).
3663 CONFIG_SPL_SKIP_RELOCATE
3664 Avoid SPL relocation
3666 CONFIG_SPL_NAND_BASE
3667 Include nand_base.c in the SPL. Requires
3668 CONFIG_SPL_NAND_DRIVERS.
3670 CONFIG_SPL_NAND_DRIVERS
3671 SPL uses normal NAND drivers, not minimal drivers.
3674 Include standard software ECC in the SPL
3676 CONFIG_SPL_NAND_SIMPLE
3677 Support for NAND boot using simple NAND drivers that
3678 expose the cmd_ctrl() interface.
3680 CONFIG_SPL_MTD_SUPPORT
3681 Support for the MTD subsystem within SPL. Useful for
3682 environment on NAND support within SPL.
3684 CONFIG_SPL_NAND_RAW_ONLY
3685 Support to boot only raw u-boot.bin images. Use this only
3686 if you need to save space.
3688 CONFIG_SPL_MPC8XXX_INIT_DDR_SUPPORT
3689 Set for the SPL on PPC mpc8xxx targets, support for
3690 drivers/ddr/fsl/libddr.o in SPL binary.
3692 CONFIG_SPL_COMMON_INIT_DDR
3693 Set for common ddr init with serial presence detect in
3696 CONFIG_SYS_NAND_5_ADDR_CYCLE, CONFIG_SYS_NAND_PAGE_COUNT,
3697 CONFIG_SYS_NAND_PAGE_SIZE, CONFIG_SYS_NAND_OOBSIZE,
3698 CONFIG_SYS_NAND_BLOCK_SIZE, CONFIG_SYS_NAND_BAD_BLOCK_POS,
3699 CONFIG_SYS_NAND_ECCPOS, CONFIG_SYS_NAND_ECCSIZE,
3700 CONFIG_SYS_NAND_ECCBYTES
3701 Defines the size and behavior of the NAND that SPL uses
3704 CONFIG_SPL_NAND_BOOT
3705 Add support NAND boot
3707 CONFIG_SYS_NAND_U_BOOT_OFFS
3708 Location in NAND to read U-Boot from
3710 CONFIG_SYS_NAND_U_BOOT_DST
3711 Location in memory to load U-Boot to
3713 CONFIG_SYS_NAND_U_BOOT_SIZE
3714 Size of image to load
3716 CONFIG_SYS_NAND_U_BOOT_START
3717 Entry point in loaded image to jump to
3719 CONFIG_SYS_NAND_HW_ECC_OOBFIRST
3720 Define this if you need to first read the OOB and then the
3721 data. This is used, for example, on davinci platforms.
3723 CONFIG_SPL_OMAP3_ID_NAND
3724 Support for an OMAP3-specific set of functions to return the
3725 ID and MFR of the first attached NAND chip, if present.
3727 CONFIG_SPL_SERIAL_SUPPORT
3728 Support for drivers/serial/libserial.o in SPL binary
3730 CONFIG_SPL_SPI_FLASH_SUPPORT
3731 Support for drivers/mtd/spi/libspi_flash.o in SPL binary
3733 CONFIG_SPL_SPI_SUPPORT
3734 Support for drivers/spi/libspi.o in SPL binary
3736 CONFIG_SPL_RAM_DEVICE
3737 Support for running image already present in ram, in SPL binary
3739 CONFIG_SPL_LIBGENERIC_SUPPORT
3740 Support for lib/libgeneric.o in SPL binary
3742 CONFIG_SPL_ENV_SUPPORT
3743 Support for the environment operating in SPL binary
3745 CONFIG_SPL_NET_SUPPORT
3746 Support for the net/libnet.o in SPL binary.
3747 It conflicts with SPL env from storage medium specified by
3748 CONFIG_ENV_IS_xxx but CONFIG_ENV_IS_NOWHERE
3751 Image offset to which the SPL should be padded before appending
3752 the SPL payload. By default, this is defined as
3753 CONFIG_SPL_MAX_SIZE, or 0 if CONFIG_SPL_MAX_SIZE is undefined.
3754 CONFIG_SPL_PAD_TO must be either 0, meaning to append the SPL
3755 payload without any padding, or >= CONFIG_SPL_MAX_SIZE.
3758 Final target image containing SPL and payload. Some SPLs
3759 use an arch-specific makefile fragment instead, for
3760 example if more than one image needs to be produced.
3762 CONFIG_FIT_SPL_PRINT
3763 Printing information about a FIT image adds quite a bit of
3764 code to SPL. So this is normally disabled in SPL. Use this
3765 option to re-enable it. This will affect the output of the
3766 bootm command when booting a FIT image.
3770 Enable building of TPL globally.
3773 Image offset to which the TPL should be padded before appending
3774 the TPL payload. By default, this is defined as
3775 CONFIG_SPL_MAX_SIZE, or 0 if CONFIG_SPL_MAX_SIZE is undefined.
3776 CONFIG_SPL_PAD_TO must be either 0, meaning to append the SPL
3777 payload without any padding, or >= CONFIG_SPL_MAX_SIZE.
3782 [so far only for SMDK2400 boards]
3784 - Modem support enable:
3785 CONFIG_MODEM_SUPPORT
3787 - RTS/CTS Flow control enable:
3790 - Modem debug support:
3791 CONFIG_MODEM_SUPPORT_DEBUG
3793 Enables debugging stuff (char screen[1024], dbg())
3794 for modem support. Useful only with BDI2000.
3796 - Interrupt support (PPC):
3798 There are common interrupt_init() and timer_interrupt()
3799 for all PPC archs. interrupt_init() calls interrupt_init_cpu()
3800 for CPU specific initialization. interrupt_init_cpu()
3801 should set decrementer_count to appropriate value. If
3802 CPU resets decrementer automatically after interrupt
3803 (ppc4xx) it should set decrementer_count to zero.
3804 timer_interrupt() calls timer_interrupt_cpu() for CPU
3805 specific handling. If board has watchdog / status_led
3806 / other_activity_monitor it works automatically from
3807 general timer_interrupt().
3811 In the target system modem support is enabled when a
3812 specific key (key combination) is pressed during
3813 power-on. Otherwise U-Boot will boot normally
3814 (autoboot). The key_pressed() function is called from
3815 board_init(). Currently key_pressed() is a dummy
3816 function, returning 1 and thus enabling modem
3819 If there are no modem init strings in the
3820 environment, U-Boot proceed to autoboot; the
3821 previous output (banner, info printfs) will be
3824 See also: doc/README.Modem
3826 Board initialization settings:
3827 ------------------------------
3829 During Initialization u-boot calls a number of board specific functions
3830 to allow the preparation of board specific prerequisites, e.g. pin setup
3831 before drivers are initialized. To enable these callbacks the
3832 following configuration macros have to be defined. Currently this is
3833 architecture specific, so please check arch/your_architecture/lib/board.c
3834 typically in board_init_f() and board_init_r().
3836 - CONFIG_BOARD_EARLY_INIT_F: Call board_early_init_f()
3837 - CONFIG_BOARD_EARLY_INIT_R: Call board_early_init_r()
3838 - CONFIG_BOARD_LATE_INIT: Call board_late_init()
3839 - CONFIG_BOARD_POSTCLK_INIT: Call board_postclk_init()
3841 Configuration Settings:
3842 -----------------------
3844 - CONFIG_SYS_SUPPORT_64BIT_DATA: Defined automatically if compiled as 64-bit.
3845 Optionally it can be defined to support 64-bit memory commands.
3847 - CONFIG_SYS_LONGHELP: Defined when you want long help messages included;
3848 undefine this when you're short of memory.
3850 - CONFIG_SYS_HELP_CMD_WIDTH: Defined when you want to override the default
3851 width of the commands listed in the 'help' command output.
3853 - CONFIG_SYS_PROMPT: This is what U-Boot prints on the console to
3854 prompt for user input.
3856 - CONFIG_SYS_CBSIZE: Buffer size for input from the Console
3858 - CONFIG_SYS_PBSIZE: Buffer size for Console output
3860 - CONFIG_SYS_MAXARGS: max. Number of arguments accepted for monitor commands
3862 - CONFIG_SYS_BARGSIZE: Buffer size for Boot Arguments which are passed to
3863 the application (usually a Linux kernel) when it is
3866 - CONFIG_SYS_BAUDRATE_TABLE:
3867 List of legal baudrate settings for this board.
3869 - CONFIG_SYS_CONSOLE_INFO_QUIET
3870 Suppress display of console information at boot.
3872 - CONFIG_SYS_CONSOLE_IS_IN_ENV
3873 If the board specific function
3874 extern int overwrite_console (void);
3875 returns 1, the stdin, stderr and stdout are switched to the
3876 serial port, else the settings in the environment are used.
3878 - CONFIG_SYS_CONSOLE_OVERWRITE_ROUTINE
3879 Enable the call to overwrite_console().
3881 - CONFIG_SYS_CONSOLE_ENV_OVERWRITE
3882 Enable overwrite of previous console environment settings.
3884 - CONFIG_SYS_MEMTEST_START, CONFIG_SYS_MEMTEST_END:
3885 Begin and End addresses of the area used by the
3888 - CONFIG_SYS_ALT_MEMTEST:
3889 Enable an alternate, more extensive memory test.
3891 - CONFIG_SYS_MEMTEST_SCRATCH:
3892 Scratch address used by the alternate memory test
3893 You only need to set this if address zero isn't writeable
3895 - CONFIG_SYS_MEM_TOP_HIDE (PPC only):
3896 If CONFIG_SYS_MEM_TOP_HIDE is defined in the board config header,
3897 this specified memory area will get subtracted from the top
3898 (end) of RAM and won't get "touched" at all by U-Boot. By
3899 fixing up gd->ram_size the Linux kernel should gets passed
3900 the now "corrected" memory size and won't touch it either.
3901 This should work for arch/ppc and arch/powerpc. Only Linux
3902 board ports in arch/powerpc with bootwrapper support that
3903 recalculate the memory size from the SDRAM controller setup
3904 will have to get fixed in Linux additionally.
3906 This option can be used as a workaround for the 440EPx/GRx
3907 CHIP 11 errata where the last 256 bytes in SDRAM shouldn't
3910 WARNING: Please make sure that this value is a multiple of
3911 the Linux page size (normally 4k). If this is not the case,
3912 then the end address of the Linux memory will be located at a
3913 non page size aligned address and this could cause major
3916 - CONFIG_SYS_LOADS_BAUD_CHANGE:
3917 Enable temporary baudrate change while serial download
3919 - CONFIG_SYS_SDRAM_BASE:
3920 Physical start address of SDRAM. _Must_ be 0 here.
3922 - CONFIG_SYS_MBIO_BASE:
3923 Physical start address of Motherboard I/O (if using a
3926 - CONFIG_SYS_FLASH_BASE:
3927 Physical start address of Flash memory.
3929 - CONFIG_SYS_MONITOR_BASE:
3930 Physical start address of boot monitor code (set by
3931 make config files to be same as the text base address
3932 (CONFIG_SYS_TEXT_BASE) used when linking) - same as
3933 CONFIG_SYS_FLASH_BASE when booting from flash.
3935 - CONFIG_SYS_MONITOR_LEN:
3936 Size of memory reserved for monitor code, used to
3937 determine _at_compile_time_ (!) if the environment is
3938 embedded within the U-Boot image, or in a separate
3941 - CONFIG_SYS_MALLOC_LEN:
3942 Size of DRAM reserved for malloc() use.
3944 - CONFIG_SYS_MALLOC_F_LEN
3945 Size of the malloc() pool for use before relocation. If
3946 this is defined, then a very simple malloc() implementation
3947 will become available before relocation. The address is just
3948 below the global data, and the stack is moved down to make
3951 This feature allocates regions with increasing addresses
3952 within the region. calloc() is supported, but realloc()
3953 is not available. free() is supported but does nothing.
3954 The memory will be freed (or in fact just forgotten) when
3955 U-Boot relocates itself.
3957 Pre-relocation malloc() is only supported on ARM and sandbox
3958 at present but is fairly easy to enable for other archs.
3960 - CONFIG_SYS_MALLOC_SIMPLE
3961 Provides a simple and small malloc() and calloc() for those
3962 boards which do not use the full malloc in SPL (which is
3963 enabled with CONFIG_SYS_SPL_MALLOC_START).
3965 - CONFIG_SYS_NONCACHED_MEMORY:
3966 Size of non-cached memory area. This area of memory will be
3967 typically located right below the malloc() area and mapped
3968 uncached in the MMU. This is useful for drivers that would
3969 otherwise require a lot of explicit cache maintenance. For
3970 some drivers it's also impossible to properly maintain the
3971 cache. For example if the regions that need to be flushed
3972 are not a multiple of the cache-line size, *and* padding
3973 cannot be allocated between the regions to align them (i.e.
3974 if the HW requires a contiguous array of regions, and the
3975 size of each region is not cache-aligned), then a flush of
3976 one region may result in overwriting data that hardware has
3977 written to another region in the same cache-line. This can
3978 happen for example in network drivers where descriptors for
3979 buffers are typically smaller than the CPU cache-line (e.g.
3980 16 bytes vs. 32 or 64 bytes).
3982 Non-cached memory is only supported on 32-bit ARM at present.
3984 - CONFIG_SYS_BOOTM_LEN:
3985 Normally compressed uImages are limited to an
3986 uncompressed size of 8 MBytes. If this is not enough,
3987 you can define CONFIG_SYS_BOOTM_LEN in your board config file
3988 to adjust this setting to your needs.
3990 - CONFIG_SYS_BOOTMAPSZ:
3991 Maximum size of memory mapped by the startup code of
3992 the Linux kernel; all data that must be processed by
3993 the Linux kernel (bd_info, boot arguments, FDT blob if
3994 used) must be put below this limit, unless "bootm_low"
3995 environment variable is defined and non-zero. In such case
3996 all data for the Linux kernel must be between "bootm_low"
3997 and "bootm_low" + CONFIG_SYS_BOOTMAPSZ. The environment
3998 variable "bootm_mapsize" will override the value of
3999 CONFIG_SYS_BOOTMAPSZ. If CONFIG_SYS_BOOTMAPSZ is undefined,
4000 then the value in "bootm_size" will be used instead.
4002 - CONFIG_SYS_BOOT_RAMDISK_HIGH:
4003 Enable initrd_high functionality. If defined then the
4004 initrd_high feature is enabled and the bootm ramdisk subcommand
4007 - CONFIG_SYS_BOOT_GET_CMDLINE:
4008 Enables allocating and saving kernel cmdline in space between
4009 "bootm_low" and "bootm_low" + BOOTMAPSZ.
4011 - CONFIG_SYS_BOOT_GET_KBD:
4012 Enables allocating and saving a kernel copy of the bd_info in
4013 space between "bootm_low" and "bootm_low" + BOOTMAPSZ.
4015 - CONFIG_SYS_MAX_FLASH_BANKS:
4016 Max number of Flash memory banks
4018 - CONFIG_SYS_MAX_FLASH_SECT:
4019 Max number of sectors on a Flash chip
4021 - CONFIG_SYS_FLASH_ERASE_TOUT:
4022 Timeout for Flash erase operations (in ms)
4024 - CONFIG_SYS_FLASH_WRITE_TOUT:
4025 Timeout for Flash write operations (in ms)
4027 - CONFIG_SYS_FLASH_LOCK_TOUT
4028 Timeout for Flash set sector lock bit operation (in ms)
4030 - CONFIG_SYS_FLASH_UNLOCK_TOUT
4031 Timeout for Flash clear lock bits operation (in ms)
4033 - CONFIG_SYS_FLASH_PROTECTION
4034 If defined, hardware flash sectors protection is used
4035 instead of U-Boot software protection.
4037 - CONFIG_SYS_DIRECT_FLASH_TFTP:
4039 Enable TFTP transfers directly to flash memory;
4040 without this option such a download has to be
4041 performed in two steps: (1) download to RAM, and (2)
4042 copy from RAM to flash.
4044 The two-step approach is usually more reliable, since
4045 you can check if the download worked before you erase
4046 the flash, but in some situations (when system RAM is
4047 too limited to allow for a temporary copy of the
4048 downloaded image) this option may be very useful.
4050 - CONFIG_SYS_FLASH_CFI:
4051 Define if the flash driver uses extra elements in the
4052 common flash structure for storing flash geometry.
4054 - CONFIG_FLASH_CFI_DRIVER
4055 This option also enables the building of the cfi_flash driver
4056 in the drivers directory
4058 - CONFIG_FLASH_CFI_MTD
4059 This option enables the building of the cfi_mtd driver
4060 in the drivers directory. The driver exports CFI flash
4063 - CONFIG_SYS_FLASH_USE_BUFFER_WRITE
4064 Use buffered writes to flash.
4066 - CONFIG_FLASH_SPANSION_S29WS_N
4067 s29ws-n MirrorBit flash has non-standard addresses for buffered
4070 - CONFIG_SYS_FLASH_QUIET_TEST
4071 If this option is defined, the common CFI flash doesn't
4072 print it's warning upon not recognized FLASH banks. This
4073 is useful, if some of the configured banks are only
4074 optionally available.
4076 - CONFIG_FLASH_SHOW_PROGRESS
4077 If defined (must be an integer), print out countdown
4078 digits and dots. Recommended value: 45 (9..1) for 80
4079 column displays, 15 (3..1) for 40 column displays.
4081 - CONFIG_FLASH_VERIFY
4082 If defined, the content of the flash (destination) is compared
4083 against the source after the write operation. An error message
4084 will be printed when the contents are not identical.
4085 Please note that this option is useless in nearly all cases,
4086 since such flash programming errors usually are detected earlier
4087 while unprotecting/erasing/programming. Please only enable
4088 this option if you really know what you are doing.
4090 - CONFIG_SYS_RX_ETH_BUFFER:
4091 Defines the number of Ethernet receive buffers. On some
4092 Ethernet controllers it is recommended to set this value
4093 to 8 or even higher (EEPRO100 or 405 EMAC), since all
4094 buffers can be full shortly after enabling the interface
4095 on high Ethernet traffic.
4096 Defaults to 4 if not defined.
4098 - CONFIG_ENV_MAX_ENTRIES
4100 Maximum number of entries in the hash table that is used
4101 internally to store the environment settings. The default
4102 setting is supposed to be generous and should work in most
4103 cases. This setting can be used to tune behaviour; see
4104 lib/hashtable.c for details.
4106 - CONFIG_ENV_FLAGS_LIST_DEFAULT
4107 - CONFIG_ENV_FLAGS_LIST_STATIC
4108 Enable validation of the values given to environment variables when
4109 calling env set. Variables can be restricted to only decimal,
4110 hexadecimal, or boolean. If CONFIG_CMD_NET is also defined,
4111 the variables can also be restricted to IP address or MAC address.
4113 The format of the list is:
4114 type_attribute = [s|d|x|b|i|m]
4115 access_attribute = [a|r|o|c]
4116 attributes = type_attribute[access_attribute]
4117 entry = variable_name[:attributes]
4120 The type attributes are:
4121 s - String (default)
4124 b - Boolean ([1yYtT|0nNfF])
4128 The access attributes are:
4134 - CONFIG_ENV_FLAGS_LIST_DEFAULT
4135 Define this to a list (string) to define the ".flags"
4136 environment variable in the default or embedded environment.
4138 - CONFIG_ENV_FLAGS_LIST_STATIC
4139 Define this to a list (string) to define validation that
4140 should be done if an entry is not found in the ".flags"
4141 environment variable. To override a setting in the static
4142 list, simply add an entry for the same variable name to the
4145 - CONFIG_ENV_ACCESS_IGNORE_FORCE
4146 If defined, don't allow the -f switch to env set override variable
4149 - CONFIG_SYS_GENERIC_BOARD
4150 This selects the architecture-generic board system instead of the
4151 architecture-specific board files. It is intended to move boards
4152 to this new framework over time. Defining this will disable the
4153 arch/foo/lib/board.c file and use common/board_f.c and
4154 common/board_r.c instead. To use this option your architecture
4155 must support it (i.e. must select HAVE_GENERIC_BOARD in arch/Kconfig).
4156 If you find problems enabling this option on your board please report
4157 the problem and send patches!
4159 - CONFIG_OMAP_PLATFORM_RESET_TIME_MAX_USEC (OMAP only)
4160 This is set by OMAP boards for the max time that reset should
4161 be asserted. See doc/README.omap-reset-time for details on how
4162 the value can be calculated on a given board.
4165 If stdint.h is available with your toolchain you can define this
4166 option to enable it. You can provide option 'USE_STDINT=1' when
4167 building U-Boot to enable this.
4169 The following definitions that deal with the placement and management
4170 of environment data (variable area); in general, we support the
4171 following configurations:
4173 - CONFIG_BUILD_ENVCRC:
4175 Builds up envcrc with the target environment so that external utils
4176 may easily extract it and embed it in final U-Boot images.
4178 - CONFIG_ENV_IS_IN_FLASH:
4180 Define this if the environment is in flash memory.
4182 a) The environment occupies one whole flash sector, which is
4183 "embedded" in the text segment with the U-Boot code. This
4184 happens usually with "bottom boot sector" or "top boot
4185 sector" type flash chips, which have several smaller
4186 sectors at the start or the end. For instance, such a
4187 layout can have sector sizes of 8, 2x4, 16, Nx32 kB. In
4188 such a case you would place the environment in one of the
4189 4 kB sectors - with U-Boot code before and after it. With
4190 "top boot sector" type flash chips, you would put the
4191 environment in one of the last sectors, leaving a gap
4192 between U-Boot and the environment.
4194 - CONFIG_ENV_OFFSET:
4196 Offset of environment data (variable area) to the
4197 beginning of flash memory; for instance, with bottom boot
4198 type flash chips the second sector can be used: the offset
4199 for this sector is given here.
4201 CONFIG_ENV_OFFSET is used relative to CONFIG_SYS_FLASH_BASE.
4205 This is just another way to specify the start address of
4206 the flash sector containing the environment (instead of
4209 - CONFIG_ENV_SECT_SIZE:
4211 Size of the sector containing the environment.
4214 b) Sometimes flash chips have few, equal sized, BIG sectors.
4215 In such a case you don't want to spend a whole sector for
4220 If you use this in combination with CONFIG_ENV_IS_IN_FLASH
4221 and CONFIG_ENV_SECT_SIZE, you can specify to use only a part
4222 of this flash sector for the environment. This saves
4223 memory for the RAM copy of the environment.
4225 It may also save flash memory if you decide to use this
4226 when your environment is "embedded" within U-Boot code,
4227 since then the remainder of the flash sector could be used
4228 for U-Boot code. It should be pointed out that this is
4229 STRONGLY DISCOURAGED from a robustness point of view:
4230 updating the environment in flash makes it always
4231 necessary to erase the WHOLE sector. If something goes
4232 wrong before the contents has been restored from a copy in
4233 RAM, your target system will be dead.
4235 - CONFIG_ENV_ADDR_REDUND
4236 CONFIG_ENV_SIZE_REDUND
4238 These settings describe a second storage area used to hold
4239 a redundant copy of the environment data, so that there is
4240 a valid backup copy in case there is a power failure during
4241 a "saveenv" operation.
4243 BE CAREFUL! Any changes to the flash layout, and some changes to the
4244 source code will make it necessary to adapt <board>/u-boot.lds*
4248 - CONFIG_ENV_IS_IN_NVRAM:
4250 Define this if you have some non-volatile memory device
4251 (NVRAM, battery buffered SRAM) which you want to use for the
4257 These two #defines are used to determine the memory area you
4258 want to use for environment. It is assumed that this memory
4259 can just be read and written to, without any special
4262 BE CAREFUL! The first access to the environment happens quite early
4263 in U-Boot initialization (when we try to get the setting of for the
4264 console baudrate). You *MUST* have mapped your NVRAM area then, or
4267 Please note that even with NVRAM we still use a copy of the
4268 environment in RAM: we could work on NVRAM directly, but we want to
4269 keep settings there always unmodified except somebody uses "saveenv"
4270 to save the current settings.
4273 - CONFIG_ENV_IS_IN_EEPROM:
4275 Use this if you have an EEPROM or similar serial access
4276 device and a driver for it.
4278 - CONFIG_ENV_OFFSET:
4281 These two #defines specify the offset and size of the
4282 environment area within the total memory of your EEPROM.
4284 - CONFIG_SYS_I2C_EEPROM_ADDR:
4285 If defined, specified the chip address of the EEPROM device.
4286 The default address is zero.
4288 - CONFIG_SYS_I2C_EEPROM_BUS:
4289 If defined, specified the i2c bus of the EEPROM device.
4291 - CONFIG_SYS_EEPROM_PAGE_WRITE_BITS:
4292 If defined, the number of bits used to address bytes in a
4293 single page in the EEPROM device. A 64 byte page, for example
4294 would require six bits.
4296 - CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS:
4297 If defined, the number of milliseconds to delay between
4298 page writes. The default is zero milliseconds.
4300 - CONFIG_SYS_I2C_EEPROM_ADDR_LEN:
4301 The length in bytes of the EEPROM memory array address. Note
4302 that this is NOT the chip address length!
4304 - CONFIG_SYS_I2C_EEPROM_ADDR_OVERFLOW:
4305 EEPROM chips that implement "address overflow" are ones
4306 like Catalyst 24WC04/08/16 which has 9/10/11 bits of
4307 address and the extra bits end up in the "chip address" bit
4308 slots. This makes a 24WC08 (1Kbyte) chip look like four 256
4311 Note that we consider the length of the address field to
4312 still be one byte because the extra address bits are hidden
4313 in the chip address.
4315 - CONFIG_SYS_EEPROM_SIZE:
4316 The size in bytes of the EEPROM device.
4318 - CONFIG_ENV_EEPROM_IS_ON_I2C
4319 define this, if you have I2C and SPI activated, and your
4320 EEPROM, which holds the environment, is on the I2C bus.
4322 - CONFIG_I2C_ENV_EEPROM_BUS
4323 if you have an Environment on an EEPROM reached over
4324 I2C muxes, you can define here, how to reach this
4325 EEPROM. For example:
4327 #define CONFIG_I2C_ENV_EEPROM_BUS 1
4329 EEPROM which holds the environment, is reached over
4330 a pca9547 i2c mux with address 0x70, channel 3.
4332 - CONFIG_ENV_IS_IN_DATAFLASH:
4334 Define this if you have a DataFlash memory device which you
4335 want to use for the environment.
4337 - CONFIG_ENV_OFFSET:
4341 These three #defines specify the offset and size of the
4342 environment area within the total memory of your DataFlash placed
4343 at the specified address.
4345 - CONFIG_ENV_IS_IN_SPI_FLASH:
4347 Define this if you have a SPI Flash memory device which you
4348 want to use for the environment.
4350 - CONFIG_ENV_OFFSET:
4353 These two #defines specify the offset and size of the
4354 environment area within the SPI Flash. CONFIG_ENV_OFFSET must be
4355 aligned to an erase sector boundary.
4357 - CONFIG_ENV_SECT_SIZE:
4359 Define the SPI flash's sector size.
4361 - CONFIG_ENV_OFFSET_REDUND (optional):
4363 This setting describes a second storage area of CONFIG_ENV_SIZE
4364 size used to hold a redundant copy of the environment data, so
4365 that there is a valid backup copy in case there is a power failure
4366 during a "saveenv" operation. CONFIG_ENV_OFFSET_RENDUND must be
4367 aligned to an erase sector boundary.
4369 - CONFIG_ENV_SPI_BUS (optional):
4370 - CONFIG_ENV_SPI_CS (optional):
4372 Define the SPI bus and chip select. If not defined they will be 0.
4374 - CONFIG_ENV_SPI_MAX_HZ (optional):
4376 Define the SPI max work clock. If not defined then use 1MHz.
4378 - CONFIG_ENV_SPI_MODE (optional):
4380 Define the SPI work mode. If not defined then use SPI_MODE_3.
4382 - CONFIG_ENV_IS_IN_REMOTE:
4384 Define this if you have a remote memory space which you
4385 want to use for the local device's environment.
4390 These two #defines specify the address and size of the
4391 environment area within the remote memory space. The
4392 local device can get the environment from remote memory
4393 space by SRIO or PCIE links.
4395 BE CAREFUL! For some special cases, the local device can not use
4396 "saveenv" command. For example, the local device will get the
4397 environment stored in a remote NOR flash by SRIO or PCIE link,
4398 but it can not erase, write this NOR flash by SRIO or PCIE interface.
4400 - CONFIG_ENV_IS_IN_NAND:
4402 Define this if you have a NAND device which you want to use
4403 for the environment.
4405 - CONFIG_ENV_OFFSET:
4408 These two #defines specify the offset and size of the environment
4409 area within the first NAND device. CONFIG_ENV_OFFSET must be
4410 aligned to an erase block boundary.
4412 - CONFIG_ENV_OFFSET_REDUND (optional):
4414 This setting describes a second storage area of CONFIG_ENV_SIZE
4415 size used to hold a redundant copy of the environment data, so
4416 that there is a valid backup copy in case there is a power failure
4417 during a "saveenv" operation. CONFIG_ENV_OFFSET_RENDUND must be
4418 aligned to an erase block boundary.
4420 - CONFIG_ENV_RANGE (optional):
4422 Specifies the length of the region in which the environment
4423 can be written. This should be a multiple of the NAND device's
4424 block size. Specifying a range with more erase blocks than
4425 are needed to hold CONFIG_ENV_SIZE allows bad blocks within
4426 the range to be avoided.
4428 - CONFIG_ENV_OFFSET_OOB (optional):
4430 Enables support for dynamically retrieving the offset of the
4431 environment from block zero's out-of-band data. The
4432 "nand env.oob" command can be used to record this offset.
4433 Currently, CONFIG_ENV_OFFSET_REDUND is not supported when
4434 using CONFIG_ENV_OFFSET_OOB.
4436 - CONFIG_NAND_ENV_DST
4438 Defines address in RAM to which the nand_spl code should copy the
4439 environment. If redundant environment is used, it will be copied to
4440 CONFIG_NAND_ENV_DST + CONFIG_ENV_SIZE.
4442 - CONFIG_ENV_IS_IN_UBI:
4444 Define this if you have an UBI volume that you want to use for the
4445 environment. This has the benefit of wear-leveling the environment
4446 accesses, which is important on NAND.
4448 - CONFIG_ENV_UBI_PART:
4450 Define this to a string that is the mtd partition containing the UBI.
4452 - CONFIG_ENV_UBI_VOLUME:
4454 Define this to the name of the volume that you want to store the
4457 - CONFIG_ENV_UBI_VOLUME_REDUND:
4459 Define this to the name of another volume to store a second copy of
4460 the environment in. This will enable redundant environments in UBI.
4461 It is assumed that both volumes are in the same MTD partition.
4463 - CONFIG_UBI_SILENCE_MSG
4464 - CONFIG_UBIFS_SILENCE_MSG
4466 You will probably want to define these to avoid a really noisy system
4467 when storing the env in UBI.
4469 - CONFIG_ENV_IS_IN_FAT:
4470 Define this if you want to use the FAT file system for the environment.
4472 - FAT_ENV_INTERFACE:
4474 Define this to a string that is the name of the block device.
4476 - FAT_ENV_DEV_AND_PART:
4478 Define this to a string to specify the partition of the device. It can
4481 "D:P", "D:0", "D", "D:" or "D:auto" (D, P are integers. And P >= 1)
4482 - "D:P": device D partition P. Error occurs if device D has no
4485 - "D" or "D:": device D partition 1 if device D has partition
4486 table, or the whole device D if has no partition
4488 - "D:auto": first partition in device D with bootable flag set.
4489 If none, first valid partition in device D. If no
4490 partition table then means device D.
4494 It's a string of the FAT file name. This file use to store the
4498 This should be defined. Otherwise it cannot save the environment file.
4500 - CONFIG_ENV_IS_IN_MMC:
4502 Define this if you have an MMC device which you want to use for the
4505 - CONFIG_SYS_MMC_ENV_DEV:
4507 Specifies which MMC device the environment is stored in.
4509 - CONFIG_SYS_MMC_ENV_PART (optional):
4511 Specifies which MMC partition the environment is stored in. If not
4512 set, defaults to partition 0, the user area. Common values might be
4513 1 (first MMC boot partition), 2 (second MMC boot partition).
4515 - CONFIG_ENV_OFFSET:
4518 These two #defines specify the offset and size of the environment
4519 area within the specified MMC device.
4521 If offset is positive (the usual case), it is treated as relative to
4522 the start of the MMC partition. If offset is negative, it is treated
4523 as relative to the end of the MMC partition. This can be useful if
4524 your board may be fitted with different MMC devices, which have
4525 different sizes for the MMC partitions, and you always want the
4526 environment placed at the very end of the partition, to leave the
4527 maximum possible space before it, to store other data.
4529 These two values are in units of bytes, but must be aligned to an
4530 MMC sector boundary.
4532 - CONFIG_ENV_OFFSET_REDUND (optional):
4534 Specifies a second storage area, of CONFIG_ENV_SIZE size, used to
4535 hold a redundant copy of the environment data. This provides a
4536 valid backup copy in case the other copy is corrupted, e.g. due
4537 to a power failure during a "saveenv" operation.
4539 This value may also be positive or negative; this is handled in the
4540 same way as CONFIG_ENV_OFFSET.
4542 This value is also in units of bytes, but must also be aligned to
4543 an MMC sector boundary.
4545 - CONFIG_ENV_SIZE_REDUND (optional):
4547 This value need not be set, even when CONFIG_ENV_OFFSET_REDUND is
4548 set. If this value is set, it must be set to the same value as
4551 - CONFIG_SYS_SPI_INIT_OFFSET
4553 Defines offset to the initial SPI buffer area in DPRAM. The
4554 area is used at an early stage (ROM part) if the environment
4555 is configured to reside in the SPI EEPROM: We need a 520 byte
4556 scratch DPRAM area. It is used between the two initialization
4557 calls (spi_init_f() and spi_init_r()). A value of 0xB00 seems
4558 to be a good choice since it makes it far enough from the
4559 start of the data area as well as from the stack pointer.
4561 Please note that the environment is read-only until the monitor
4562 has been relocated to RAM and a RAM copy of the environment has been
4563 created; also, when using EEPROM you will have to use getenv_f()
4564 until then to read environment variables.
4566 The environment is protected by a CRC32 checksum. Before the monitor
4567 is relocated into RAM, as a result of a bad CRC you will be working
4568 with the compiled-in default environment - *silently*!!! [This is
4569 necessary, because the first environment variable we need is the
4570 "baudrate" setting for the console - if we have a bad CRC, we don't
4571 have any device yet where we could complain.]
4573 Note: once the monitor has been relocated, then it will complain if
4574 the default environment is used; a new CRC is computed as soon as you
4575 use the "saveenv" command to store a valid environment.
4577 - CONFIG_SYS_FAULT_ECHO_LINK_DOWN:
4578 Echo the inverted Ethernet link state to the fault LED.
4580 Note: If this option is active, then CONFIG_SYS_FAULT_MII_ADDR
4581 also needs to be defined.
4583 - CONFIG_SYS_FAULT_MII_ADDR:
4584 MII address of the PHY to check for the Ethernet link state.
4586 - CONFIG_NS16550_MIN_FUNCTIONS:
4587 Define this if you desire to only have use of the NS16550_init
4588 and NS16550_putc functions for the serial driver located at
4589 drivers/serial/ns16550.c. This option is useful for saving
4590 space for already greatly restricted images, including but not
4591 limited to NAND_SPL configurations.
4593 - CONFIG_DISPLAY_BOARDINFO
4594 Display information about the board that U-Boot is running on
4595 when U-Boot starts up. The board function checkboard() is called
4598 - CONFIG_DISPLAY_BOARDINFO_LATE
4599 Similar to the previous option, but display this information
4600 later, once stdio is running and output goes to the LCD, if
4603 - CONFIG_BOARD_SIZE_LIMIT:
4604 Maximum size of the U-Boot image. When defined, the
4605 build system checks that the actual size does not
4608 Low Level (hardware related) configuration options:
4609 ---------------------------------------------------
4611 - CONFIG_SYS_CACHELINE_SIZE:
4612 Cache Line Size of the CPU.
4614 - CONFIG_SYS_DEFAULT_IMMR:
4615 Default address of the IMMR after system reset.
4617 Needed on some 8260 systems (MPC8260ADS, PQ2FADS-ZU,
4618 and RPXsuper) to be able to adjust the position of
4619 the IMMR register after a reset.
4621 - CONFIG_SYS_CCSRBAR_DEFAULT:
4622 Default (power-on reset) physical address of CCSR on Freescale
4625 - CONFIG_SYS_CCSRBAR:
4626 Virtual address of CCSR. On a 32-bit build, this is typically
4627 the same value as CONFIG_SYS_CCSRBAR_DEFAULT.
4629 CONFIG_SYS_DEFAULT_IMMR must also be set to this value,
4630 for cross-platform code that uses that macro instead.
4632 - CONFIG_SYS_CCSRBAR_PHYS:
4633 Physical address of CCSR. CCSR can be relocated to a new
4634 physical address, if desired. In this case, this macro should
4635 be set to that address. Otherwise, it should be set to the
4636 same value as CONFIG_SYS_CCSRBAR_DEFAULT. For example, CCSR
4637 is typically relocated on 36-bit builds. It is recommended
4638 that this macro be defined via the _HIGH and _LOW macros:
4640 #define CONFIG_SYS_CCSRBAR_PHYS ((CONFIG_SYS_CCSRBAR_PHYS_HIGH
4641 * 1ull) << 32 | CONFIG_SYS_CCSRBAR_PHYS_LOW)
4643 - CONFIG_SYS_CCSRBAR_PHYS_HIGH:
4644 Bits 33-36 of CONFIG_SYS_CCSRBAR_PHYS. This value is typically
4645 either 0 (32-bit build) or 0xF (36-bit build). This macro is
4646 used in assembly code, so it must not contain typecasts or
4647 integer size suffixes (e.g. "ULL").
4649 - CONFIG_SYS_CCSRBAR_PHYS_LOW:
4650 Lower 32-bits of CONFIG_SYS_CCSRBAR_PHYS. This macro is
4651 used in assembly code, so it must not contain typecasts or
4652 integer size suffixes (e.g. "ULL").
4654 - CONFIG_SYS_CCSR_DO_NOT_RELOCATE:
4655 If this macro is defined, then CONFIG_SYS_CCSRBAR_PHYS will be
4656 forced to a value that ensures that CCSR is not relocated.
4658 - Floppy Disk Support:
4659 CONFIG_SYS_FDC_DRIVE_NUMBER
4661 the default drive number (default value 0)
4663 CONFIG_SYS_ISA_IO_STRIDE
4665 defines the spacing between FDC chipset registers
4668 CONFIG_SYS_ISA_IO_OFFSET
4670 defines the offset of register from address. It
4671 depends on which part of the data bus is connected to
4672 the FDC chipset. (default value 0)
4674 If CONFIG_SYS_ISA_IO_STRIDE CONFIG_SYS_ISA_IO_OFFSET and
4675 CONFIG_SYS_FDC_DRIVE_NUMBER are undefined, they take their
4678 if CONFIG_SYS_FDC_HW_INIT is defined, then the function
4679 fdc_hw_init() is called at the beginning of the FDC
4680 setup. fdc_hw_init() must be provided by the board
4681 source code. It is used to make hardware-dependent
4685 Most IDE controllers were designed to be connected with PCI
4686 interface. Only few of them were designed for AHB interface.
4687 When software is doing ATA command and data transfer to
4688 IDE devices through IDE-AHB controller, some additional
4689 registers accessing to these kind of IDE-AHB controller
4692 - CONFIG_SYS_IMMR: Physical address of the Internal Memory.
4693 DO NOT CHANGE unless you know exactly what you're
4694 doing! (11-4) [MPC8xx/82xx systems only]
4696 - CONFIG_SYS_INIT_RAM_ADDR:
4698 Start address of memory area that can be used for
4699 initial data and stack; please note that this must be
4700 writable memory that is working WITHOUT special
4701 initialization, i. e. you CANNOT use normal RAM which
4702 will become available only after programming the
4703 memory controller and running certain initialization
4706 U-Boot uses the following memory types:
4707 - MPC8xx and MPC8260: IMMR (internal memory of the CPU)
4708 - MPC824X: data cache
4709 - PPC4xx: data cache
4711 - CONFIG_SYS_GBL_DATA_OFFSET:
4713 Offset of the initial data structure in the memory
4714 area defined by CONFIG_SYS_INIT_RAM_ADDR. Usually
4715 CONFIG_SYS_GBL_DATA_OFFSET is chosen such that the initial
4716 data is located at the end of the available space
4717 (sometimes written as (CONFIG_SYS_INIT_RAM_SIZE -
4718 CONFIG_SYS_INIT_DATA_SIZE), and the initial stack is just
4719 below that area (growing from (CONFIG_SYS_INIT_RAM_ADDR +
4720 CONFIG_SYS_GBL_DATA_OFFSET) downward.
4723 On the MPC824X (or other systems that use the data
4724 cache for initial memory) the address chosen for
4725 CONFIG_SYS_INIT_RAM_ADDR is basically arbitrary - it must
4726 point to an otherwise UNUSED address space between
4727 the top of RAM and the start of the PCI space.
4729 - CONFIG_SYS_SIUMCR: SIU Module Configuration (11-6)
4731 - CONFIG_SYS_SYPCR: System Protection Control (11-9)
4733 - CONFIG_SYS_TBSCR: Time Base Status and Control (11-26)
4735 - CONFIG_SYS_PISCR: Periodic Interrupt Status and Control (11-31)
4737 - CONFIG_SYS_PLPRCR: PLL, Low-Power, and Reset Control Register (15-30)
4739 - CONFIG_SYS_SCCR: System Clock and reset Control Register (15-27)
4741 - CONFIG_SYS_OR_TIMING_SDRAM:
4744 - CONFIG_SYS_MAMR_PTA:
4745 periodic timer for refresh
4747 - CONFIG_SYS_DER: Debug Event Register (37-47)
4749 - FLASH_BASE0_PRELIM, FLASH_BASE1_PRELIM, CONFIG_SYS_REMAP_OR_AM,
4750 CONFIG_SYS_PRELIM_OR_AM, CONFIG_SYS_OR_TIMING_FLASH, CONFIG_SYS_OR0_REMAP,
4751 CONFIG_SYS_OR0_PRELIM, CONFIG_SYS_BR0_PRELIM, CONFIG_SYS_OR1_REMAP, CONFIG_SYS_OR1_PRELIM,
4752 CONFIG_SYS_BR1_PRELIM:
4753 Memory Controller Definitions: BR0/1 and OR0/1 (FLASH)
4755 - SDRAM_BASE2_PRELIM, SDRAM_BASE3_PRELIM, SDRAM_MAX_SIZE,
4756 CONFIG_SYS_OR_TIMING_SDRAM, CONFIG_SYS_OR2_PRELIM, CONFIG_SYS_BR2_PRELIM,
4757 CONFIG_SYS_OR3_PRELIM, CONFIG_SYS_BR3_PRELIM:
4758 Memory Controller Definitions: BR2/3 and OR2/3 (SDRAM)
4760 - CONFIG_SYS_MAMR_PTA, CONFIG_SYS_MPTPR_2BK_4K, CONFIG_SYS_MPTPR_1BK_4K, CONFIG_SYS_MPTPR_2BK_8K,
4761 CONFIG_SYS_MPTPR_1BK_8K, CONFIG_SYS_MAMR_8COL, CONFIG_SYS_MAMR_9COL:
4762 Machine Mode Register and Memory Periodic Timer
4763 Prescaler definitions (SDRAM timing)
4765 - CONFIG_SYS_I2C_UCODE_PATCH, CONFIG_SYS_I2C_DPMEM_OFFSET [0x1FC0]:
4766 enable I2C microcode relocation patch (MPC8xx);
4767 define relocation offset in DPRAM [DSP2]
4769 - CONFIG_SYS_SMC_UCODE_PATCH, CONFIG_SYS_SMC_DPMEM_OFFSET [0x1FC0]:
4770 enable SMC microcode relocation patch (MPC8xx);
4771 define relocation offset in DPRAM [SMC1]
4773 - CONFIG_SYS_SPI_UCODE_PATCH, CONFIG_SYS_SPI_DPMEM_OFFSET [0x1FC0]:
4774 enable SPI microcode relocation patch (MPC8xx);
4775 define relocation offset in DPRAM [SCC4]
4777 - CONFIG_SYS_USE_OSCCLK:
4778 Use OSCM clock mode on MBX8xx board. Be careful,
4779 wrong setting might damage your board. Read
4780 doc/README.MBX before setting this variable!
4782 - CONFIG_SYS_CPM_POST_WORD_ADDR: (MPC8xx, MPC8260 only)
4783 Offset of the bootmode word in DPRAM used by post
4784 (Power On Self Tests). This definition overrides
4785 #define'd default value in commproc.h resp.
4788 - CONFIG_SYS_PCI_SLV_MEM_LOCAL, CONFIG_SYS_PCI_SLV_MEM_BUS, CONFIG_SYS_PICMR0_MASK_ATTRIB,
4789 CONFIG_SYS_PCI_MSTR0_LOCAL, CONFIG_SYS_PCIMSK0_MASK, CONFIG_SYS_PCI_MSTR1_LOCAL,
4790 CONFIG_SYS_PCIMSK1_MASK, CONFIG_SYS_PCI_MSTR_MEM_LOCAL, CONFIG_SYS_PCI_MSTR_MEM_BUS,
4791 CONFIG_SYS_CPU_PCI_MEM_START, CONFIG_SYS_PCI_MSTR_MEM_SIZE, CONFIG_SYS_POCMR0_MASK_ATTRIB,
4792 CONFIG_SYS_PCI_MSTR_MEMIO_LOCAL, CONFIG_SYS_PCI_MSTR_MEMIO_BUS, CPU_PCI_MEMIO_START,
4793 CONFIG_SYS_PCI_MSTR_MEMIO_SIZE, CONFIG_SYS_POCMR1_MASK_ATTRIB, CONFIG_SYS_PCI_MSTR_IO_LOCAL,
4794 CONFIG_SYS_PCI_MSTR_IO_BUS, CONFIG_SYS_CPU_PCI_IO_START, CONFIG_SYS_PCI_MSTR_IO_SIZE,
4795 CONFIG_SYS_POCMR2_MASK_ATTRIB: (MPC826x only)
4796 Overrides the default PCI memory map in arch/powerpc/cpu/mpc8260/pci.c if set.
4798 - CONFIG_PCI_DISABLE_PCIE:
4799 Disable PCI-Express on systems where it is supported but not
4802 - CONFIG_PCI_ENUM_ONLY
4803 Only scan through and get the devices on the buses.
4804 Don't do any setup work, presumably because someone or
4805 something has already done it, and we don't need to do it
4806 a second time. Useful for platforms that are pre-booted
4807 by coreboot or similar.
4809 - CONFIG_PCI_INDIRECT_BRIDGE:
4810 Enable support for indirect PCI bridges.
4813 Chip has SRIO or not
4816 Board has SRIO 1 port available
4819 Board has SRIO 2 port available
4821 - CONFIG_SRIO_PCIE_BOOT_MASTER
4822 Board can support master function for Boot from SRIO and PCIE
4824 - CONFIG_SYS_SRIOn_MEM_VIRT:
4825 Virtual Address of SRIO port 'n' memory region
4827 - CONFIG_SYS_SRIOn_MEM_PHYS:
4828 Physical Address of SRIO port 'n' memory region
4830 - CONFIG_SYS_SRIOn_MEM_SIZE:
4831 Size of SRIO port 'n' memory region
4833 - CONFIG_SYS_NAND_BUSWIDTH_16BIT
4834 Defined to tell the NAND controller that the NAND chip is using
4836 Not all NAND drivers use this symbol.
4837 Example of drivers that use it:
4838 - drivers/mtd/nand/ndfc.c
4839 - drivers/mtd/nand/mxc_nand.c
4841 - CONFIG_SYS_NDFC_EBC0_CFG
4842 Sets the EBC0_CFG register for the NDFC. If not defined
4843 a default value will be used.
4846 Get DDR timing information from an I2C EEPROM. Common
4847 with pluggable memory modules such as SODIMMs
4850 I2C address of the SPD EEPROM
4852 - CONFIG_SYS_SPD_BUS_NUM
4853 If SPD EEPROM is on an I2C bus other than the first
4854 one, specify here. Note that the value must resolve
4855 to something your driver can deal with.
4857 - CONFIG_SYS_DDR_RAW_TIMING
4858 Get DDR timing information from other than SPD. Common with
4859 soldered DDR chips onboard without SPD. DDR raw timing
4860 parameters are extracted from datasheet and hard-coded into
4861 header files or board specific files.
4863 - CONFIG_FSL_DDR_INTERACTIVE
4864 Enable interactive DDR debugging. See doc/README.fsl-ddr.
4866 - CONFIG_FSL_DDR_SYNC_REFRESH
4867 Enable sync of refresh for multiple controllers.
4869 - CONFIG_FSL_DDR_BIST
4870 Enable built-in memory test for Freescale DDR controllers.
4872 - CONFIG_SYS_83XX_DDR_USES_CS0
4873 Only for 83xx systems. If specified, then DDR should
4874 be configured using CS0 and CS1 instead of CS2 and CS3.
4876 - CONFIG_ETHER_ON_FEC[12]
4877 Define to enable FEC[12] on a 8xx series processor.
4879 - CONFIG_FEC[12]_PHY
4880 Define to the hardcoded PHY address which corresponds
4881 to the given FEC; i. e.
4882 #define CONFIG_FEC1_PHY 4
4883 means that the PHY with address 4 is connected to FEC1
4885 When set to -1, means to probe for first available.
4887 - CONFIG_FEC[12]_PHY_NORXERR
4888 The PHY does not have a RXERR line (RMII only).
4889 (so program the FEC to ignore it).
4892 Enable RMII mode for all FECs.
4893 Note that this is a global option, we can't
4894 have one FEC in standard MII mode and another in RMII mode.
4896 - CONFIG_CRC32_VERIFY
4897 Add a verify option to the crc32 command.
4900 => crc32 -v <address> <count> <crc32>
4902 Where address/count indicate a memory area
4903 and crc32 is the correct crc32 which the
4907 Add the "loopw" memory command. This only takes effect if
4908 the memory commands are activated globally (CONFIG_CMD_MEM).
4911 Add the "mdc" and "mwc" memory commands. These are cyclic
4916 This command will print 4 bytes (10,11,12,13) each 500 ms.
4918 => mwc.l 100 12345678 10
4919 This command will write 12345678 to address 100 all 10 ms.
4921 This only takes effect if the memory commands are activated
4922 globally (CONFIG_CMD_MEM).
4924 - CONFIG_SKIP_LOWLEVEL_INIT
4925 [ARM, NDS32, MIPS only] If this variable is defined, then certain
4926 low level initializations (like setting up the memory
4927 controller) are omitted and/or U-Boot does not
4928 relocate itself into RAM.
4930 Normally this variable MUST NOT be defined. The only
4931 exception is when U-Boot is loaded (to RAM) by some
4932 other boot loader or by a debugger which performs
4933 these initializations itself.
4936 Modifies the behaviour of start.S when compiling a loader
4937 that is executed before the actual U-Boot. E.g. when
4938 compiling a NAND SPL.
4941 Modifies the behaviour of start.S when compiling a loader
4942 that is executed after the SPL and before the actual U-Boot.
4943 It is loaded by the SPL.
4945 - CONFIG_SYS_MPC85XX_NO_RESETVEC
4946 Only for 85xx systems. If this variable is specified, the section
4947 .resetvec is not kept and the section .bootpg is placed in the
4948 previous 4k of the .text section.
4950 - CONFIG_ARCH_MAP_SYSMEM
4951 Generally U-Boot (and in particular the md command) uses
4952 effective address. It is therefore not necessary to regard
4953 U-Boot address as virtual addresses that need to be translated
4954 to physical addresses. However, sandbox requires this, since
4955 it maintains its own little RAM buffer which contains all
4956 addressable memory. This option causes some memory accesses
4957 to be mapped through map_sysmem() / unmap_sysmem().
4959 - CONFIG_USE_ARCH_MEMCPY
4960 CONFIG_USE_ARCH_MEMSET
4961 If these options are used a optimized version of memcpy/memset will
4962 be used if available. These functions may be faster under some
4963 conditions but may increase the binary size.
4965 - CONFIG_X86_RESET_VECTOR
4966 If defined, the x86 reset vector code is included. This is not
4967 needed when U-Boot is running from Coreboot.
4970 Defines the MPU clock speed (in MHz).
4972 NOTE : currently only supported on AM335x platforms.
4974 - CONFIG_SPL_AM33XX_ENABLE_RTC32K_OSC:
4975 Enables the RTC32K OSC on AM33xx based plattforms
4977 - CONFIG_SYS_NAND_NO_SUBPAGE_WRITE
4978 Option to disable subpage write in NAND driver
4979 driver that uses this:
4980 drivers/mtd/nand/davinci_nand.c
4982 Freescale QE/FMAN Firmware Support:
4983 -----------------------------------
4985 The Freescale QUICCEngine (QE) and Frame Manager (FMAN) both support the
4986 loading of "firmware", which is encoded in the QE firmware binary format.
4987 This firmware often needs to be loaded during U-Boot booting, so macros
4988 are used to identify the storage device (NOR flash, SPI, etc) and the address
4991 - CONFIG_SYS_FMAN_FW_ADDR
4992 The address in the storage device where the FMAN microcode is located. The
4993 meaning of this address depends on which CONFIG_SYS_QE_FW_IN_xxx macro
4996 - CONFIG_SYS_QE_FW_ADDR
4997 The address in the storage device where the QE microcode is located. The
4998 meaning of this address depends on which CONFIG_SYS_QE_FW_IN_xxx macro
5001 - CONFIG_SYS_QE_FMAN_FW_LENGTH
5002 The maximum possible size of the firmware. The firmware binary format
5003 has a field that specifies the actual size of the firmware, but it
5004 might not be possible to read any part of the firmware unless some
5005 local storage is allocated to hold the entire firmware first.
5007 - CONFIG_SYS_QE_FMAN_FW_IN_NOR
5008 Specifies that QE/FMAN firmware is located in NOR flash, mapped as
5009 normal addressable memory via the LBC. CONFIG_SYS_FMAN_FW_ADDR is the
5010 virtual address in NOR flash.
5012 - CONFIG_SYS_QE_FMAN_FW_IN_NAND
5013 Specifies that QE/FMAN firmware is located in NAND flash.
5014 CONFIG_SYS_FMAN_FW_ADDR is the offset within NAND flash.
5016 - CONFIG_SYS_QE_FMAN_FW_IN_MMC
5017 Specifies that QE/FMAN firmware is located on the primary SD/MMC
5018 device. CONFIG_SYS_FMAN_FW_ADDR is the byte offset on that device.
5020 - CONFIG_SYS_QE_FMAN_FW_IN_SPIFLASH
5021 Specifies that QE/FMAN firmware is located on the primary SPI
5022 device. CONFIG_SYS_FMAN_FW_ADDR is the byte offset on that device.
5024 - CONFIG_SYS_QE_FMAN_FW_IN_REMOTE
5025 Specifies that QE/FMAN firmware is located in the remote (master)
5026 memory space. CONFIG_SYS_FMAN_FW_ADDR is a virtual address which
5027 can be mapped from slave TLB->slave LAW->slave SRIO or PCIE outbound
5028 window->master inbound window->master LAW->the ucode address in
5029 master's memory space.
5031 Freescale Layerscape Management Complex Firmware Support:
5032 ---------------------------------------------------------
5033 The Freescale Layerscape Management Complex (MC) supports the loading of
5035 This firmware often needs to be loaded during U-Boot booting, so macros
5036 are used to identify the storage device (NOR flash, SPI, etc) and the address
5039 - CONFIG_FSL_MC_ENET
5040 Enable the MC driver for Layerscape SoCs.
5042 - CONFIG_SYS_LS_MC_FW_ADDR
5043 The address in the storage device where the firmware is located. The
5044 meaning of this address depends on which CONFIG_SYS_LS_MC_FW_IN_xxx macro
5047 - CONFIG_SYS_LS_MC_FW_LENGTH
5048 The maximum possible size of the firmware. The firmware binary format
5049 has a field that specifies the actual size of the firmware, but it
5050 might not be possible to read any part of the firmware unless some
5051 local storage is allocated to hold the entire firmware first.
5053 - CONFIG_SYS_LS_MC_FW_IN_NOR
5054 Specifies that MC firmware is located in NOR flash, mapped as
5055 normal addressable memory via the LBC. CONFIG_SYS_LS_MC_FW_ADDR is the
5056 virtual address in NOR flash.
5058 Building the Software:
5059 ======================
5061 Building U-Boot has been tested in several native build environments
5062 and in many different cross environments. Of course we cannot support
5063 all possibly existing versions of cross development tools in all
5064 (potentially obsolete) versions. In case of tool chain problems we
5065 recommend to use the ELDK (see http://www.denx.de/wiki/DULG/ELDK)
5066 which is extensively used to build and test U-Boot.
5068 If you are not using a native environment, it is assumed that you
5069 have GNU cross compiling tools available in your path. In this case,
5070 you must set the environment variable CROSS_COMPILE in your shell.
5071 Note that no changes to the Makefile or any other source files are
5072 necessary. For example using the ELDK on a 4xx CPU, please enter:
5074 $ CROSS_COMPILE=ppc_4xx-
5075 $ export CROSS_COMPILE
5077 Note: If you wish to generate Windows versions of the utilities in
5078 the tools directory you can use the MinGW toolchain
5079 (http://www.mingw.org). Set your HOST tools to the MinGW
5080 toolchain and execute 'make tools'. For example:
5082 $ make HOSTCC=i586-mingw32msvc-gcc HOSTSTRIP=i586-mingw32msvc-strip tools
5084 Binaries such as tools/mkimage.exe will be created which can
5085 be executed on computers running Windows.
5087 U-Boot is intended to be simple to build. After installing the
5088 sources you must configure U-Boot for one specific board type. This
5093 where "NAME_defconfig" is the name of one of the existing configu-
5094 rations; see boards.cfg for supported names.
5096 Note: for some board special configuration names may exist; check if
5097 additional information is available from the board vendor; for
5098 instance, the TQM823L systems are available without (standard)
5099 or with LCD support. You can select such additional "features"
5100 when choosing the configuration, i. e.
5102 make TQM823L_defconfig
5103 - will configure for a plain TQM823L, i. e. no LCD support
5105 make TQM823L_LCD_defconfig
5106 - will configure for a TQM823L with U-Boot console on LCD
5111 Finally, type "make all", and you should get some working U-Boot
5112 images ready for download to / installation on your system:
5114 - "u-boot.bin" is a raw binary image
5115 - "u-boot" is an image in ELF binary format
5116 - "u-boot.srec" is in Motorola S-Record format
5118 By default the build is performed locally and the objects are saved
5119 in the source directory. One of the two methods can be used to change
5120 this behavior and build U-Boot to some external directory:
5122 1. Add O= to the make command line invocations:
5124 make O=/tmp/build distclean
5125 make O=/tmp/build NAME_defconfig
5126 make O=/tmp/build all
5128 2. Set environment variable KBUILD_OUTPUT to point to the desired location:
5130 export KBUILD_OUTPUT=/tmp/build
5135 Note that the command line "O=" setting overrides the KBUILD_OUTPUT environment
5139 Please be aware that the Makefiles assume you are using GNU make, so
5140 for instance on NetBSD you might need to use "gmake" instead of
5144 If the system board that you have is not listed, then you will need
5145 to port U-Boot to your hardware platform. To do this, follow these
5148 1. Add a new configuration option for your board to the toplevel
5149 "boards.cfg" file, using the existing entries as examples.
5150 Follow the instructions there to keep the boards in order.
5151 2. Create a new directory to hold your board specific code. Add any
5152 files you need. In your board directory, you will need at least
5153 the "Makefile", a "<board>.c", "flash.c" and "u-boot.lds".
5154 3. Create a new configuration file "include/configs/<board>.h" for
5156 3. If you're porting U-Boot to a new CPU, then also create a new
5157 directory to hold your CPU specific code. Add any files you need.
5158 4. Run "make <board>_defconfig" with your new name.
5159 5. Type "make", and you should get a working "u-boot.srec" file
5160 to be installed on your target system.
5161 6. Debug and solve any problems that might arise.
5162 [Of course, this last step is much harder than it sounds.]
5165 Testing of U-Boot Modifications, Ports to New Hardware, etc.:
5166 ==============================================================
5168 If you have modified U-Boot sources (for instance added a new board
5169 or support for new devices, a new CPU, etc.) you are expected to
5170 provide feedback to the other developers. The feedback normally takes
5171 the form of a "patch", i. e. a context diff against a certain (latest
5172 official or latest in the git repository) version of U-Boot sources.
5174 But before you submit such a patch, please verify that your modifi-
5175 cation did not break existing code. At least make sure that *ALL* of
5176 the supported boards compile WITHOUT ANY compiler warnings. To do so,
5177 just run the "MAKEALL" script, which will configure and build U-Boot
5178 for ALL supported system. Be warned, this will take a while. You can
5179 select which (cross) compiler to use by passing a `CROSS_COMPILE'
5180 environment variable to the script, i. e. to use the ELDK cross tools
5183 CROSS_COMPILE=ppc_8xx- MAKEALL
5185 or to build on a native PowerPC system you can type
5187 CROSS_COMPILE=' ' MAKEALL
5189 When using the MAKEALL script, the default behaviour is to build
5190 U-Boot in the source directory. This location can be changed by
5191 setting the BUILD_DIR environment variable. Also, for each target
5192 built, the MAKEALL script saves two log files (<target>.ERR and
5193 <target>.MAKEALL) in the <source dir>/LOG directory. This default
5194 location can be changed by setting the MAKEALL_LOGDIR environment
5195 variable. For example:
5197 export BUILD_DIR=/tmp/build
5198 export MAKEALL_LOGDIR=/tmp/log
5199 CROSS_COMPILE=ppc_8xx- MAKEALL
5201 With the above settings build objects are saved in the /tmp/build,
5202 log files are saved in the /tmp/log and the source tree remains clean
5203 during the whole build process.
5206 See also "U-Boot Porting Guide" below.
5209 Monitor Commands - Overview:
5210 ============================
5212 go - start application at address 'addr'
5213 run - run commands in an environment variable
5214 bootm - boot application image from memory
5215 bootp - boot image via network using BootP/TFTP protocol
5216 bootz - boot zImage from memory
5217 tftpboot- boot image via network using TFTP protocol
5218 and env variables "ipaddr" and "serverip"
5219 (and eventually "gatewayip")
5220 tftpput - upload a file via network using TFTP protocol
5221 rarpboot- boot image via network using RARP/TFTP protocol
5222 diskboot- boot from IDE devicebootd - boot default, i.e., run 'bootcmd'
5223 loads - load S-Record file over serial line
5224 loadb - load binary file over serial line (kermit mode)
5226 mm - memory modify (auto-incrementing)
5227 nm - memory modify (constant address)
5228 mw - memory write (fill)
5230 cmp - memory compare
5231 crc32 - checksum calculation
5232 i2c - I2C sub-system
5233 sspi - SPI utility commands
5234 base - print or set address offset
5235 printenv- print environment variables
5236 setenv - set environment variables
5237 saveenv - save environment variables to persistent storage
5238 protect - enable or disable FLASH write protection
5239 erase - erase FLASH memory
5240 flinfo - print FLASH memory information
5241 nand - NAND memory operations (see doc/README.nand)
5242 bdinfo - print Board Info structure
5243 iminfo - print header information for application image
5244 coninfo - print console devices and informations
5245 ide - IDE sub-system
5246 loop - infinite loop on address range
5247 loopw - infinite write loop on address range
5248 mtest - simple RAM test
5249 icache - enable or disable instruction cache
5250 dcache - enable or disable data cache
5251 reset - Perform RESET of the CPU
5252 echo - echo args to console
5253 version - print monitor version
5254 help - print online help
5255 ? - alias for 'help'
5258 Monitor Commands - Detailed Description:
5259 ========================================
5263 For now: just type "help <command>".
5266 Environment Variables:
5267 ======================
5269 U-Boot supports user configuration using Environment Variables which
5270 can be made persistent by saving to Flash memory.
5272 Environment Variables are set using "setenv", printed using
5273 "printenv", and saved to Flash using "saveenv". Using "setenv"
5274 without a value can be used to delete a variable from the
5275 environment. As long as you don't save the environment you are
5276 working with an in-memory copy. In case the Flash area containing the
5277 environment is erased by accident, a default environment is provided.
5279 Some configuration options can be set using Environment Variables.
5281 List of environment variables (most likely not complete):
5283 baudrate - see CONFIG_BAUDRATE
5285 bootdelay - see CONFIG_BOOTDELAY
5287 bootcmd - see CONFIG_BOOTCOMMAND
5289 bootargs - Boot arguments when booting an RTOS image
5291 bootfile - Name of the image to load with TFTP
5293 bootm_low - Memory range available for image processing in the bootm
5294 command can be restricted. This variable is given as
5295 a hexadecimal number and defines lowest address allowed
5296 for use by the bootm command. See also "bootm_size"
5297 environment variable. Address defined by "bootm_low" is
5298 also the base of the initial memory mapping for the Linux
5299 kernel -- see the description of CONFIG_SYS_BOOTMAPSZ and
5302 bootm_mapsize - Size of the initial memory mapping for the Linux kernel.
5303 This variable is given as a hexadecimal number and it
5304 defines the size of the memory region starting at base
5305 address bootm_low that is accessible by the Linux kernel
5306 during early boot. If unset, CONFIG_SYS_BOOTMAPSZ is used
5307 as the default value if it is defined, and bootm_size is
5310 bootm_size - Memory range available for image processing in the bootm
5311 command can be restricted. This variable is given as
5312 a hexadecimal number and defines the size of the region
5313 allowed for use by the bootm command. See also "bootm_low"
5314 environment variable.
5316 updatefile - Location of the software update file on a TFTP server, used
5317 by the automatic software update feature. Please refer to
5318 documentation in doc/README.update for more details.
5320 autoload - if set to "no" (any string beginning with 'n'),
5321 "bootp" will just load perform a lookup of the
5322 configuration from the BOOTP server, but not try to
5323 load any image using TFTP
5325 autostart - if set to "yes", an image loaded using the "bootp",
5326 "rarpboot", "tftpboot" or "diskboot" commands will
5327 be automatically started (by internally calling
5330 If set to "no", a standalone image passed to the
5331 "bootm" command will be copied to the load address
5332 (and eventually uncompressed), but NOT be started.
5333 This can be used to load and uncompress arbitrary
5336 fdt_high - if set this restricts the maximum address that the
5337 flattened device tree will be copied into upon boot.
5338 For example, if you have a system with 1 GB memory
5339 at physical address 0x10000000, while Linux kernel
5340 only recognizes the first 704 MB as low memory, you
5341 may need to set fdt_high as 0x3C000000 to have the
5342 device tree blob be copied to the maximum address
5343 of the 704 MB low memory, so that Linux kernel can
5344 access it during the boot procedure.
5346 If this is set to the special value 0xFFFFFFFF then
5347 the fdt will not be copied at all on boot. For this
5348 to work it must reside in writable memory, have
5349 sufficient padding on the end of it for u-boot to
5350 add the information it needs into it, and the memory
5351 must be accessible by the kernel.
5353 fdtcontroladdr- if set this is the address of the control flattened
5354 device tree used by U-Boot when CONFIG_OF_CONTROL is
5357 i2cfast - (PPC405GP|PPC405EP only)
5358 if set to 'y' configures Linux I2C driver for fast
5359 mode (400kHZ). This environment variable is used in
5360 initialization code. So, for changes to be effective
5361 it must be saved and board must be reset.
5363 initrd_high - restrict positioning of initrd images:
5364 If this variable is not set, initrd images will be
5365 copied to the highest possible address in RAM; this
5366 is usually what you want since it allows for
5367 maximum initrd size. If for some reason you want to
5368 make sure that the initrd image is loaded below the
5369 CONFIG_SYS_BOOTMAPSZ limit, you can set this environment
5370 variable to a value of "no" or "off" or "0".
5371 Alternatively, you can set it to a maximum upper
5372 address to use (U-Boot will still check that it
5373 does not overwrite the U-Boot stack and data).
5375 For instance, when you have a system with 16 MB
5376 RAM, and want to reserve 4 MB from use by Linux,
5377 you can do this by adding "mem=12M" to the value of
5378 the "bootargs" variable. However, now you must make
5379 sure that the initrd image is placed in the first
5380 12 MB as well - this can be done with
5382 setenv initrd_high 00c00000
5384 If you set initrd_high to 0xFFFFFFFF, this is an
5385 indication to U-Boot that all addresses are legal
5386 for the Linux kernel, including addresses in flash
5387 memory. In this case U-Boot will NOT COPY the
5388 ramdisk at all. This may be useful to reduce the
5389 boot time on your system, but requires that this
5390 feature is supported by your Linux kernel.
5392 ipaddr - IP address; needed for tftpboot command
5394 loadaddr - Default load address for commands like "bootp",
5395 "rarpboot", "tftpboot", "loadb" or "diskboot"
5397 loads_echo - see CONFIG_LOADS_ECHO
5399 serverip - TFTP server IP address; needed for tftpboot command
5401 bootretry - see CONFIG_BOOT_RETRY_TIME
5403 bootdelaykey - see CONFIG_AUTOBOOT_DELAY_STR
5405 bootstopkey - see CONFIG_AUTOBOOT_STOP_STR
5407 ethprime - controls which interface is used first.
5409 ethact - controls which interface is currently active.
5410 For example you can do the following
5412 => setenv ethact FEC
5413 => ping 192.168.0.1 # traffic sent on FEC
5414 => setenv ethact SCC
5415 => ping 10.0.0.1 # traffic sent on SCC
5417 ethrotate - When set to "no" U-Boot does not go through all
5418 available network interfaces.
5419 It just stays at the currently selected interface.
5421 netretry - When set to "no" each network operation will
5422 either succeed or fail without retrying.
5423 When set to "once" the network operation will
5424 fail when all the available network interfaces
5425 are tried once without success.
5426 Useful on scripts which control the retry operation
5429 npe_ucode - set load address for the NPE microcode
5431 silent_linux - If set then Linux will be told to boot silently, by
5432 changing the console to be empty. If "yes" it will be
5433 made silent. If "no" it will not be made silent. If
5434 unset, then it will be made silent if the U-Boot console
5437 tftpsrcport - If this is set, the value is used for TFTP's
5440 tftpdstport - If this is set, the value is used for TFTP's UDP
5441 destination port instead of the Well Know Port 69.
5443 tftpblocksize - Block size to use for TFTP transfers; if not set,
5444 we use the TFTP server's default block size
5446 tftptimeout - Retransmission timeout for TFTP packets (in milli-
5447 seconds, minimum value is 1000 = 1 second). Defines
5448 when a packet is considered to be lost so it has to
5449 be retransmitted. The default is 5000 = 5 seconds.
5450 Lowering this value may make downloads succeed
5451 faster in networks with high packet loss rates or
5452 with unreliable TFTP servers.
5454 vlan - When set to a value < 4095 the traffic over
5455 Ethernet is encapsulated/received over 802.1q
5458 The following image location variables contain the location of images
5459 used in booting. The "Image" column gives the role of the image and is
5460 not an environment variable name. The other columns are environment
5461 variable names. "File Name" gives the name of the file on a TFTP
5462 server, "RAM Address" gives the location in RAM the image will be
5463 loaded to, and "Flash Location" gives the image's address in NOR
5464 flash or offset in NAND flash.
5466 *Note* - these variables don't have to be defined for all boards, some
5467 boards currently use other variables for these purposes, and some
5468 boards use these variables for other purposes.
5470 Image File Name RAM Address Flash Location
5471 ----- --------- ----------- --------------
5472 u-boot u-boot u-boot_addr_r u-boot_addr
5473 Linux kernel bootfile kernel_addr_r kernel_addr
5474 device tree blob fdtfile fdt_addr_r fdt_addr
5475 ramdisk ramdiskfile ramdisk_addr_r ramdisk_addr
5477 The following environment variables may be used and automatically
5478 updated by the network boot commands ("bootp" and "rarpboot"),
5479 depending the information provided by your boot server:
5481 bootfile - see above
5482 dnsip - IP address of your Domain Name Server
5483 dnsip2 - IP address of your secondary Domain Name Server
5484 gatewayip - IP address of the Gateway (Router) to use
5485 hostname - Target hostname
5487 netmask - Subnet Mask
5488 rootpath - Pathname of the root filesystem on the NFS server
5489 serverip - see above
5492 There are two special Environment Variables:
5494 serial# - contains hardware identification information such
5495 as type string and/or serial number
5496 ethaddr - Ethernet address
5498 These variables can be set only once (usually during manufacturing of
5499 the board). U-Boot refuses to delete or overwrite these variables
5500 once they have been set once.
5503 Further special Environment Variables:
5505 ver - Contains the U-Boot version string as printed
5506 with the "version" command. This variable is
5507 readonly (see CONFIG_VERSION_VARIABLE).
5510 Please note that changes to some configuration parameters may take
5511 only effect after the next boot (yes, that's just like Windoze :-).
5514 Callback functions for environment variables:
5515 ---------------------------------------------
5517 For some environment variables, the behavior of u-boot needs to change
5518 when their values are changed. This functionality allows functions to
5519 be associated with arbitrary variables. On creation, overwrite, or
5520 deletion, the callback will provide the opportunity for some side
5521 effect to happen or for the change to be rejected.
5523 The callbacks are named and associated with a function using the
5524 U_BOOT_ENV_CALLBACK macro in your board or driver code.
5526 These callbacks are associated with variables in one of two ways. The
5527 static list can be added to by defining CONFIG_ENV_CALLBACK_LIST_STATIC
5528 in the board configuration to a string that defines a list of
5529 associations. The list must be in the following format:
5531 entry = variable_name[:callback_name]
5534 If the callback name is not specified, then the callback is deleted.
5535 Spaces are also allowed anywhere in the list.
5537 Callbacks can also be associated by defining the ".callbacks" variable
5538 with the same list format above. Any association in ".callbacks" will
5539 override any association in the static list. You can define
5540 CONFIG_ENV_CALLBACK_LIST_DEFAULT to a list (string) to define the
5541 ".callbacks" environment variable in the default or embedded environment.
5544 Command Line Parsing:
5545 =====================
5547 There are two different command line parsers available with U-Boot:
5548 the old "simple" one, and the much more powerful "hush" shell:
5550 Old, simple command line parser:
5551 --------------------------------
5553 - supports environment variables (through setenv / saveenv commands)
5554 - several commands on one line, separated by ';'
5555 - variable substitution using "... ${name} ..." syntax
5556 - special characters ('$', ';') can be escaped by prefixing with '\',
5558 setenv bootcmd bootm \${address}
5559 - You can also escape text by enclosing in single apostrophes, for example:
5560 setenv addip 'setenv bootargs $bootargs ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname::off'
5565 - similar to Bourne shell, with control structures like
5566 if...then...else...fi, for...do...done; while...do...done,
5567 until...do...done, ...
5568 - supports environment ("global") variables (through setenv / saveenv
5569 commands) and local shell variables (through standard shell syntax
5570 "name=value"); only environment variables can be used with "run"
5576 (1) If a command line (or an environment variable executed by a "run"
5577 command) contains several commands separated by semicolon, and
5578 one of these commands fails, then the remaining commands will be
5581 (2) If you execute several variables with one call to run (i. e.
5582 calling run with a list of variables as arguments), any failing
5583 command will cause "run" to terminate, i. e. the remaining
5584 variables are not executed.
5586 Note for Redundant Ethernet Interfaces:
5587 =======================================
5589 Some boards come with redundant Ethernet interfaces; U-Boot supports
5590 such configurations and is capable of automatic selection of a
5591 "working" interface when needed. MAC assignment works as follows:
5593 Network interfaces are numbered eth0, eth1, eth2, ... Corresponding
5594 MAC addresses can be stored in the environment as "ethaddr" (=>eth0),
5595 "eth1addr" (=>eth1), "eth2addr", ...
5597 If the network interface stores some valid MAC address (for instance
5598 in SROM), this is used as default address if there is NO correspon-
5599 ding setting in the environment; if the corresponding environment
5600 variable is set, this overrides the settings in the card; that means:
5602 o If the SROM has a valid MAC address, and there is no address in the
5603 environment, the SROM's address is used.
5605 o If there is no valid address in the SROM, and a definition in the
5606 environment exists, then the value from the environment variable is
5609 o If both the SROM and the environment contain a MAC address, and
5610 both addresses are the same, this MAC address is used.
5612 o If both the SROM and the environment contain a MAC address, and the
5613 addresses differ, the value from the environment is used and a
5616 o If neither SROM nor the environment contain a MAC address, an error
5617 is raised. If CONFIG_NET_RANDOM_ETHADDR is defined, then in this case
5618 a random, locally-assigned MAC is used.
5620 If Ethernet drivers implement the 'write_hwaddr' function, valid MAC addresses
5621 will be programmed into hardware as part of the initialization process. This
5622 may be skipped by setting the appropriate 'ethmacskip' environment variable.
5623 The naming convention is as follows:
5624 "ethmacskip" (=>eth0), "eth1macskip" (=>eth1) etc.
5629 U-Boot is capable of booting (and performing other auxiliary operations on)
5630 images in two formats:
5632 New uImage format (FIT)
5633 -----------------------
5635 Flexible and powerful format based on Flattened Image Tree -- FIT (similar
5636 to Flattened Device Tree). It allows the use of images with multiple
5637 components (several kernels, ramdisks, etc.), with contents protected by
5638 SHA1, MD5 or CRC32. More details are found in the doc/uImage.FIT directory.
5644 Old image format is based on binary files which can be basically anything,
5645 preceded by a special header; see the definitions in include/image.h for
5646 details; basically, the header defines the following image properties:
5648 * Target Operating System (Provisions for OpenBSD, NetBSD, FreeBSD,
5649 4.4BSD, Linux, SVR4, Esix, Solaris, Irix, SCO, Dell, NCR, VxWorks,
5650 LynxOS, pSOS, QNX, RTEMS, INTEGRITY;
5651 Currently supported: Linux, NetBSD, VxWorks, QNX, RTEMS, LynxOS,
5653 * Target CPU Architecture (Provisions for Alpha, ARM, AVR32, Intel x86,
5654 IA64, MIPS, NDS32, Nios II, PowerPC, IBM S390, SuperH, Sparc, Sparc 64 Bit;
5655 Currently supported: ARM, AVR32, Intel x86, MIPS, NDS32, Nios II, PowerPC).
5656 * Compression Type (uncompressed, gzip, bzip2)
5662 The header is marked by a special Magic Number, and both the header
5663 and the data portions of the image are secured against corruption by
5670 Although U-Boot should support any OS or standalone application
5671 easily, the main focus has always been on Linux during the design of
5674 U-Boot includes many features that so far have been part of some
5675 special "boot loader" code within the Linux kernel. Also, any
5676 "initrd" images to be used are no longer part of one big Linux image;
5677 instead, kernel and "initrd" are separate images. This implementation
5678 serves several purposes:
5680 - the same features can be used for other OS or standalone
5681 applications (for instance: using compressed images to reduce the
5682 Flash memory footprint)
5684 - it becomes much easier to port new Linux kernel versions because
5685 lots of low-level, hardware dependent stuff are done by U-Boot
5687 - the same Linux kernel image can now be used with different "initrd"
5688 images; of course this also means that different kernel images can
5689 be run with the same "initrd". This makes testing easier (you don't
5690 have to build a new "zImage.initrd" Linux image when you just
5691 change a file in your "initrd"). Also, a field-upgrade of the
5692 software is easier now.
5698 Porting Linux to U-Boot based systems:
5699 ---------------------------------------
5701 U-Boot cannot save you from doing all the necessary modifications to
5702 configure the Linux device drivers for use with your target hardware
5703 (no, we don't intend to provide a full virtual machine interface to
5706 But now you can ignore ALL boot loader code (in arch/powerpc/mbxboot).
5708 Just make sure your machine specific header file (for instance
5709 include/asm-ppc/tqm8xx.h) includes the same definition of the Board
5710 Information structure as we define in include/asm-<arch>/u-boot.h,
5711 and make sure that your definition of IMAP_ADDR uses the same value
5712 as your U-Boot configuration in CONFIG_SYS_IMMR.
5714 Note that U-Boot now has a driver model, a unified model for drivers.
5715 If you are adding a new driver, plumb it into driver model. If there
5716 is no uclass available, you are encouraged to create one. See
5720 Configuring the Linux kernel:
5721 -----------------------------
5723 No specific requirements for U-Boot. Make sure you have some root
5724 device (initial ramdisk, NFS) for your target system.
5727 Building a Linux Image:
5728 -----------------------
5730 With U-Boot, "normal" build targets like "zImage" or "bzImage" are
5731 not used. If you use recent kernel source, a new build target
5732 "uImage" will exist which automatically builds an image usable by
5733 U-Boot. Most older kernels also have support for a "pImage" target,
5734 which was introduced for our predecessor project PPCBoot and uses a
5735 100% compatible format.
5739 make TQM850L_defconfig
5744 The "uImage" build target uses a special tool (in 'tools/mkimage') to
5745 encapsulate a compressed Linux kernel image with header information,
5746 CRC32 checksum etc. for use with U-Boot. This is what we are doing:
5748 * build a standard "vmlinux" kernel image (in ELF binary format):
5750 * convert the kernel into a raw binary image:
5752 ${CROSS_COMPILE}-objcopy -O binary \
5753 -R .note -R .comment \
5754 -S vmlinux linux.bin
5756 * compress the binary image:
5760 * package compressed binary image for U-Boot:
5762 mkimage -A ppc -O linux -T kernel -C gzip \
5763 -a 0 -e 0 -n "Linux Kernel Image" \
5764 -d linux.bin.gz uImage
5767 The "mkimage" tool can also be used to create ramdisk images for use
5768 with U-Boot, either separated from the Linux kernel image, or
5769 combined into one file. "mkimage" encapsulates the images with a 64
5770 byte header containing information about target architecture,
5771 operating system, image type, compression method, entry points, time
5772 stamp, CRC32 checksums, etc.
5774 "mkimage" can be called in two ways: to verify existing images and
5775 print the header information, or to build new images.
5777 In the first form (with "-l" option) mkimage lists the information
5778 contained in the header of an existing U-Boot image; this includes
5779 checksum verification:
5781 tools/mkimage -l image
5782 -l ==> list image header information
5784 The second form (with "-d" option) is used to build a U-Boot image
5785 from a "data file" which is used as image payload:
5787 tools/mkimage -A arch -O os -T type -C comp -a addr -e ep \
5788 -n name -d data_file image
5789 -A ==> set architecture to 'arch'
5790 -O ==> set operating system to 'os'
5791 -T ==> set image type to 'type'
5792 -C ==> set compression type 'comp'
5793 -a ==> set load address to 'addr' (hex)
5794 -e ==> set entry point to 'ep' (hex)
5795 -n ==> set image name to 'name'
5796 -d ==> use image data from 'datafile'
5798 Right now, all Linux kernels for PowerPC systems use the same load
5799 address (0x00000000), but the entry point address depends on the
5802 - 2.2.x kernels have the entry point at 0x0000000C,
5803 - 2.3.x and later kernels have the entry point at 0x00000000.
5805 So a typical call to build a U-Boot image would read:
5807 -> tools/mkimage -n '2.4.4 kernel for TQM850L' \
5808 > -A ppc -O linux -T kernel -C gzip -a 0 -e 0 \
5809 > -d /opt/elsk/ppc_8xx/usr/src/linux-2.4.4/arch/powerpc/coffboot/vmlinux.gz \
5810 > examples/uImage.TQM850L
5811 Image Name: 2.4.4 kernel for TQM850L
5812 Created: Wed Jul 19 02:34:59 2000
5813 Image Type: PowerPC Linux Kernel Image (gzip compressed)
5814 Data Size: 335725 Bytes = 327.86 kB = 0.32 MB
5815 Load Address: 0x00000000
5816 Entry Point: 0x00000000
5818 To verify the contents of the image (or check for corruption):
5820 -> tools/mkimage -l examples/uImage.TQM850L
5821 Image Name: 2.4.4 kernel for TQM850L
5822 Created: Wed Jul 19 02:34:59 2000
5823 Image Type: PowerPC Linux Kernel Image (gzip compressed)
5824 Data Size: 335725 Bytes = 327.86 kB = 0.32 MB
5825 Load Address: 0x00000000
5826 Entry Point: 0x00000000
5828 NOTE: for embedded systems where boot time is critical you can trade
5829 speed for memory and install an UNCOMPRESSED image instead: this
5830 needs more space in Flash, but boots much faster since it does not
5831 need to be uncompressed:
5833 -> gunzip /opt/elsk/ppc_8xx/usr/src/linux-2.4.4/arch/powerpc/coffboot/vmlinux.gz
5834 -> tools/mkimage -n '2.4.4 kernel for TQM850L' \
5835 > -A ppc -O linux -T kernel -C none -a 0 -e 0 \
5836 > -d /opt/elsk/ppc_8xx/usr/src/linux-2.4.4/arch/powerpc/coffboot/vmlinux \
5837 > examples/uImage.TQM850L-uncompressed
5838 Image Name: 2.4.4 kernel for TQM850L
5839 Created: Wed Jul 19 02:34:59 2000
5840 Image Type: PowerPC Linux Kernel Image (uncompressed)
5841 Data Size: 792160 Bytes = 773.59 kB = 0.76 MB
5842 Load Address: 0x00000000
5843 Entry Point: 0x00000000
5846 Similar you can build U-Boot images from a 'ramdisk.image.gz' file
5847 when your kernel is intended to use an initial ramdisk:
5849 -> tools/mkimage -n 'Simple Ramdisk Image' \
5850 > -A ppc -O linux -T ramdisk -C gzip \
5851 > -d /LinuxPPC/images/SIMPLE-ramdisk.image.gz examples/simple-initrd
5852 Image Name: Simple Ramdisk Image
5853 Created: Wed Jan 12 14:01:50 2000
5854 Image Type: PowerPC Linux RAMDisk Image (gzip compressed)
5855 Data Size: 566530 Bytes = 553.25 kB = 0.54 MB
5856 Load Address: 0x00000000
5857 Entry Point: 0x00000000
5859 The "dumpimage" is a tool to disassemble images built by mkimage. Its "-i"
5860 option performs the converse operation of the mkimage's second form (the "-d"
5861 option). Given an image built by mkimage, the dumpimage extracts a "data file"
5864 tools/dumpimage -i image -T type -p position data_file
5865 -i ==> extract from the 'image' a specific 'data_file'
5866 -T ==> set image type to 'type'
5867 -p ==> 'position' (starting at 0) of the 'data_file' inside the 'image'
5870 Installing a Linux Image:
5871 -------------------------
5873 To downloading a U-Boot image over the serial (console) interface,
5874 you must convert the image to S-Record format:
5876 objcopy -I binary -O srec examples/image examples/image.srec
5878 The 'objcopy' does not understand the information in the U-Boot
5879 image header, so the resulting S-Record file will be relative to
5880 address 0x00000000. To load it to a given address, you need to
5881 specify the target address as 'offset' parameter with the 'loads'
5884 Example: install the image to address 0x40100000 (which on the
5885 TQM8xxL is in the first Flash bank):
5887 => erase 40100000 401FFFFF
5893 ## Ready for S-Record download ...
5894 ~>examples/image.srec
5895 1 2 3 4 5 6 7 8 9 10 11 12 13 ...
5897 15989 15990 15991 15992
5898 [file transfer complete]
5900 ## Start Addr = 0x00000000
5903 You can check the success of the download using the 'iminfo' command;
5904 this includes a checksum verification so you can be sure no data
5905 corruption happened:
5909 ## Checking Image at 40100000 ...
5910 Image Name: 2.2.13 for initrd on TQM850L
5911 Image Type: PowerPC Linux Kernel Image (gzip compressed)
5912 Data Size: 335725 Bytes = 327 kB = 0 MB
5913 Load Address: 00000000
5914 Entry Point: 0000000c
5915 Verifying Checksum ... OK
5921 The "bootm" command is used to boot an application that is stored in
5922 memory (RAM or Flash). In case of a Linux kernel image, the contents
5923 of the "bootargs" environment variable is passed to the kernel as
5924 parameters. You can check and modify this variable using the
5925 "printenv" and "setenv" commands:
5928 => printenv bootargs
5929 bootargs=root=/dev/ram
5931 => setenv bootargs root=/dev/nfs rw nfsroot=10.0.0.2:/LinuxPPC nfsaddrs=10.0.0.99:10.0.0.2
5933 => printenv bootargs
5934 bootargs=root=/dev/nfs rw nfsroot=10.0.0.2:/LinuxPPC nfsaddrs=10.0.0.99:10.0.0.2
5937 ## Booting Linux kernel at 40020000 ...
5938 Image Name: 2.2.13 for NFS on TQM850L
5939 Image Type: PowerPC Linux Kernel Image (gzip compressed)
5940 Data Size: 381681 Bytes = 372 kB = 0 MB
5941 Load Address: 00000000
5942 Entry Point: 0000000c
5943 Verifying Checksum ... OK
5944 Uncompressing Kernel Image ... OK
5945 Linux version 2.2.13 (wd@denx.local.net) (gcc version 2.95.2 19991024 (release)) #1 Wed Jul 19 02:35:17 MEST 2000
5946 Boot arguments: root=/dev/nfs rw nfsroot=10.0.0.2:/LinuxPPC nfsaddrs=10.0.0.99:10.0.0.2
5947 time_init: decrementer frequency = 187500000/60
5948 Calibrating delay loop... 49.77 BogoMIPS
5949 Memory: 15208k available (700k kernel code, 444k data, 32k init) [c0000000,c1000000]
5952 If you want to boot a Linux kernel with initial RAM disk, you pass
5953 the memory addresses of both the kernel and the initrd image (PPBCOOT
5954 format!) to the "bootm" command:
5956 => imi 40100000 40200000
5958 ## Checking Image at 40100000 ...
5959 Image Name: 2.2.13 for initrd on TQM850L
5960 Image Type: PowerPC Linux Kernel Image (gzip compressed)
5961 Data Size: 335725 Bytes = 327 kB = 0 MB
5962 Load Address: 00000000
5963 Entry Point: 0000000c
5964 Verifying Checksum ... OK
5966 ## Checking Image at 40200000 ...
5967 Image Name: Simple Ramdisk Image
5968 Image Type: PowerPC Linux RAMDisk Image (gzip compressed)
5969 Data Size: 566530 Bytes = 553 kB = 0 MB
5970 Load Address: 00000000
5971 Entry Point: 00000000
5972 Verifying Checksum ... OK
5974 => bootm 40100000 40200000
5975 ## Booting Linux kernel at 40100000 ...
5976 Image Name: 2.2.13 for initrd on TQM850L
5977 Image Type: PowerPC Linux Kernel Image (gzip compressed)
5978 Data Size: 335725 Bytes = 327 kB = 0 MB
5979 Load Address: 00000000
5980 Entry Point: 0000000c
5981 Verifying Checksum ... OK
5982 Uncompressing Kernel Image ... OK
5983 ## Loading RAMDisk Image at 40200000 ...
5984 Image Name: Simple Ramdisk Image
5985 Image Type: PowerPC Linux RAMDisk Image (gzip compressed)
5986 Data Size: 566530 Bytes = 553 kB = 0 MB
5987 Load Address: 00000000
5988 Entry Point: 00000000
5989 Verifying Checksum ... OK
5990 Loading Ramdisk ... OK
5991 Linux version 2.2.13 (wd@denx.local.net) (gcc version 2.95.2 19991024 (release)) #1 Wed Jul 19 02:32:08 MEST 2000
5992 Boot arguments: root=/dev/ram
5993 time_init: decrementer frequency = 187500000/60
5994 Calibrating delay loop... 49.77 BogoMIPS
5996 RAMDISK: Compressed image found at block 0
5997 VFS: Mounted root (ext2 filesystem).
6001 Boot Linux and pass a flat device tree:
6004 First, U-Boot must be compiled with the appropriate defines. See the section
6005 titled "Linux Kernel Interface" above for a more in depth explanation. The
6006 following is an example of how to start a kernel and pass an updated
6012 oft=oftrees/mpc8540ads.dtb
6013 => tftp $oftaddr $oft
6014 Speed: 1000, full duplex
6016 TFTP from server 192.168.1.1; our IP address is 192.168.1.101
6017 Filename 'oftrees/mpc8540ads.dtb'.
6018 Load address: 0x300000
6021 Bytes transferred = 4106 (100a hex)
6022 => tftp $loadaddr $bootfile
6023 Speed: 1000, full duplex
6025 TFTP from server 192.168.1.1; our IP address is 192.168.1.2
6027 Load address: 0x200000
6028 Loading:############
6030 Bytes transferred = 1029407 (fb51f hex)
6035 => bootm $loadaddr - $oftaddr
6036 ## Booting image at 00200000 ...
6037 Image Name: Linux-2.6.17-dirty
6038 Image Type: PowerPC Linux Kernel Image (gzip compressed)
6039 Data Size: 1029343 Bytes = 1005.2 kB
6040 Load Address: 00000000
6041 Entry Point: 00000000
6042 Verifying Checksum ... OK
6043 Uncompressing Kernel Image ... OK
6044 Booting using flat device tree at 0x300000
6045 Using MPC85xx ADS machine description
6046 Memory CAM mapping: CAM0=256Mb, CAM1=256Mb, CAM2=0Mb residual: 0Mb
6050 More About U-Boot Image Types:
6051 ------------------------------
6053 U-Boot supports the following image types:
6055 "Standalone Programs" are directly runnable in the environment
6056 provided by U-Boot; it is expected that (if they behave
6057 well) you can continue to work in U-Boot after return from
6058 the Standalone Program.
6059 "OS Kernel Images" are usually images of some Embedded OS which
6060 will take over control completely. Usually these programs
6061 will install their own set of exception handlers, device
6062 drivers, set up the MMU, etc. - this means, that you cannot
6063 expect to re-enter U-Boot except by resetting the CPU.
6064 "RAMDisk Images" are more or less just data blocks, and their
6065 parameters (address, size) are passed to an OS kernel that is
6067 "Multi-File Images" contain several images, typically an OS
6068 (Linux) kernel image and one or more data images like
6069 RAMDisks. This construct is useful for instance when you want
6070 to boot over the network using BOOTP etc., where the boot
6071 server provides just a single image file, but you want to get
6072 for instance an OS kernel and a RAMDisk image.
6074 "Multi-File Images" start with a list of image sizes, each
6075 image size (in bytes) specified by an "uint32_t" in network
6076 byte order. This list is terminated by an "(uint32_t)0".
6077 Immediately after the terminating 0 follow the images, one by
6078 one, all aligned on "uint32_t" boundaries (size rounded up to
6079 a multiple of 4 bytes).
6081 "Firmware Images" are binary images containing firmware (like
6082 U-Boot or FPGA images) which usually will be programmed to
6085 "Script files" are command sequences that will be executed by
6086 U-Boot's command interpreter; this feature is especially
6087 useful when you configure U-Boot to use a real shell (hush)
6088 as command interpreter.
6090 Booting the Linux zImage:
6091 -------------------------
6093 On some platforms, it's possible to boot Linux zImage. This is done
6094 using the "bootz" command. The syntax of "bootz" command is the same
6095 as the syntax of "bootm" command.
6097 Note, defining the CONFIG_SUPPORT_RAW_INITRD allows user to supply
6098 kernel with raw initrd images. The syntax is slightly different, the
6099 address of the initrd must be augmented by it's size, in the following
6100 format: "<initrd addres>:<initrd size>".
6106 One of the features of U-Boot is that you can dynamically load and
6107 run "standalone" applications, which can use some resources of
6108 U-Boot like console I/O functions or interrupt services.
6110 Two simple examples are included with the sources:
6115 'examples/hello_world.c' contains a small "Hello World" Demo
6116 application; it is automatically compiled when you build U-Boot.
6117 It's configured to run at address 0x00040004, so you can play with it
6121 ## Ready for S-Record download ...
6122 ~>examples/hello_world.srec
6123 1 2 3 4 5 6 7 8 9 10 11 ...
6124 [file transfer complete]
6126 ## Start Addr = 0x00040004
6128 => go 40004 Hello World! This is a test.
6129 ## Starting application at 0x00040004 ...
6140 Hit any key to exit ...
6142 ## Application terminated, rc = 0x0
6144 Another example, which demonstrates how to register a CPM interrupt
6145 handler with the U-Boot code, can be found in 'examples/timer.c'.
6146 Here, a CPM timer is set up to generate an interrupt every second.
6147 The interrupt service routine is trivial, just printing a '.'
6148 character, but this is just a demo program. The application can be
6149 controlled by the following keys:
6151 ? - print current values og the CPM Timer registers
6152 b - enable interrupts and start timer
6153 e - stop timer and disable interrupts
6154 q - quit application
6157 ## Ready for S-Record download ...
6158 ~>examples/timer.srec
6159 1 2 3 4 5 6 7 8 9 10 11 ...
6160 [file transfer complete]
6162 ## Start Addr = 0x00040004
6165 ## Starting application at 0x00040004 ...
6168 tgcr @ 0xfff00980, tmr @ 0xfff00990, trr @ 0xfff00994, tcr @ 0xfff00998, tcn @ 0xfff0099c, ter @ 0xfff009b0
6171 [q, b, e, ?] Set interval 1000000 us
6174 [q, b, e, ?] ........
6175 tgcr=0x1, tmr=0xff1c, trr=0x3d09, tcr=0x0, tcn=0xef6, ter=0x0
6178 tgcr=0x1, tmr=0xff1c, trr=0x3d09, tcr=0x0, tcn=0x2ad4, ter=0x0
6181 tgcr=0x1, tmr=0xff1c, trr=0x3d09, tcr=0x0, tcn=0x1efc, ter=0x0
6184 tgcr=0x1, tmr=0xff1c, trr=0x3d09, tcr=0x0, tcn=0x169d, ter=0x0
6186 [q, b, e, ?] ...Stopping timer
6188 [q, b, e, ?] ## Application terminated, rc = 0x0
6194 Over time, many people have reported problems when trying to use the
6195 "minicom" terminal emulation program for serial download. I (wd)
6196 consider minicom to be broken, and recommend not to use it. Under
6197 Unix, I recommend to use C-Kermit for general purpose use (and
6198 especially for kermit binary protocol download ("loadb" command), and
6199 use "cu" for S-Record download ("loads" command). See
6200 http://www.denx.de/wiki/view/DULG/SystemSetup#Section_4.3.
6201 for help with kermit.
6204 Nevertheless, if you absolutely want to use it try adding this
6205 configuration to your "File transfer protocols" section:
6207 Name Program Name U/D FullScr IO-Red. Multi
6208 X kermit /usr/bin/kermit -i -l %l -s Y U Y N N
6209 Y kermit /usr/bin/kermit -i -l %l -r N D Y N N
6215 Starting at version 0.9.2, U-Boot supports NetBSD both as host
6216 (build U-Boot) and target system (boots NetBSD/mpc8xx).
6218 Building requires a cross environment; it is known to work on
6219 NetBSD/i386 with the cross-powerpc-netbsd-1.3 package (you will also
6220 need gmake since the Makefiles are not compatible with BSD make).
6221 Note that the cross-powerpc package does not install include files;
6222 attempting to build U-Boot will fail because <machine/ansi.h> is
6223 missing. This file has to be installed and patched manually:
6225 # cd /usr/pkg/cross/powerpc-netbsd/include
6227 # ln -s powerpc machine
6228 # cp /usr/src/sys/arch/powerpc/include/ansi.h powerpc/ansi.h
6229 # ${EDIT} powerpc/ansi.h ## must remove __va_list, _BSD_VA_LIST
6231 Native builds *don't* work due to incompatibilities between native
6232 and U-Boot include files.
6234 Booting assumes that (the first part of) the image booted is a
6235 stage-2 loader which in turn loads and then invokes the kernel
6236 proper. Loader sources will eventually appear in the NetBSD source
6237 tree (probably in sys/arc/mpc8xx/stand/u-boot_stage2/); in the
6238 meantime, see ftp://ftp.denx.de/pub/u-boot/ppcboot_stage2.tar.gz
6241 Implementation Internals:
6242 =========================
6244 The following is not intended to be a complete description of every
6245 implementation detail. However, it should help to understand the
6246 inner workings of U-Boot and make it easier to port it to custom
6250 Initial Stack, Global Data:
6251 ---------------------------
6253 The implementation of U-Boot is complicated by the fact that U-Boot
6254 starts running out of ROM (flash memory), usually without access to
6255 system RAM (because the memory controller is not initialized yet).
6256 This means that we don't have writable Data or BSS segments, and BSS
6257 is not initialized as zero. To be able to get a C environment working
6258 at all, we have to allocate at least a minimal stack. Implementation
6259 options for this are defined and restricted by the CPU used: Some CPU
6260 models provide on-chip memory (like the IMMR area on MPC8xx and
6261 MPC826x processors), on others (parts of) the data cache can be
6262 locked as (mis-) used as memory, etc.
6264 Chris Hallinan posted a good summary of these issues to the
6265 U-Boot mailing list:
6267 Subject: RE: [U-Boot-Users] RE: More On Memory Bank x (nothingness)?
6268 From: "Chris Hallinan" <clh@net1plus.com>
6269 Date: Mon, 10 Feb 2003 16:43:46 -0500 (22:43 MET)
6272 Correct me if I'm wrong, folks, but the way I understand it
6273 is this: Using DCACHE as initial RAM for Stack, etc, does not
6274 require any physical RAM backing up the cache. The cleverness
6275 is that the cache is being used as a temporary supply of
6276 necessary storage before the SDRAM controller is setup. It's
6277 beyond the scope of this list to explain the details, but you
6278 can see how this works by studying the cache architecture and
6279 operation in the architecture and processor-specific manuals.
6281 OCM is On Chip Memory, which I believe the 405GP has 4K. It
6282 is another option for the system designer to use as an
6283 initial stack/RAM area prior to SDRAM being available. Either
6284 option should work for you. Using CS 4 should be fine if your
6285 board designers haven't used it for something that would
6286 cause you grief during the initial boot! It is frequently not
6289 CONFIG_SYS_INIT_RAM_ADDR should be somewhere that won't interfere
6290 with your processor/board/system design. The default value
6291 you will find in any recent u-boot distribution in
6292 walnut.h should work for you. I'd set it to a value larger
6293 than your SDRAM module. If you have a 64MB SDRAM module, set
6294 it above 400_0000. Just make sure your board has no resources
6295 that are supposed to respond to that address! That code in
6296 start.S has been around a while and should work as is when
6297 you get the config right.
6302 It is essential to remember this, since it has some impact on the C
6303 code for the initialization procedures:
6305 * Initialized global data (data segment) is read-only. Do not attempt
6308 * Do not use any uninitialized global data (or implicitly initialized
6309 as zero data - BSS segment) at all - this is undefined, initiali-
6310 zation is performed later (when relocating to RAM).
6312 * Stack space is very limited. Avoid big data buffers or things like
6315 Having only the stack as writable memory limits means we cannot use
6316 normal global data to share information between the code. But it
6317 turned out that the implementation of U-Boot can be greatly
6318 simplified by making a global data structure (gd_t) available to all
6319 functions. We could pass a pointer to this data as argument to _all_
6320 functions, but this would bloat the code. Instead we use a feature of
6321 the GCC compiler (Global Register Variables) to share the data: we
6322 place a pointer (gd) to the global data into a register which we
6323 reserve for this purpose.
6325 When choosing a register for such a purpose we are restricted by the
6326 relevant (E)ABI specifications for the current architecture, and by
6327 GCC's implementation.
6329 For PowerPC, the following registers have specific use:
6331 R2: reserved for system use
6332 R3-R4: parameter passing and return values
6333 R5-R10: parameter passing
6334 R13: small data area pointer
6338 (U-Boot also uses R12 as internal GOT pointer. r12
6339 is a volatile register so r12 needs to be reset when
6340 going back and forth between asm and C)
6342 ==> U-Boot will use R2 to hold a pointer to the global data
6344 Note: on PPC, we could use a static initializer (since the
6345 address of the global data structure is known at compile time),
6346 but it turned out that reserving a register results in somewhat
6347 smaller code - although the code savings are not that big (on
6348 average for all boards 752 bytes for the whole U-Boot image,
6349 624 text + 127 data).
6351 On Blackfin, the normal C ABI (except for P3) is followed as documented here:
6352 http://docs.blackfin.uclinux.org/doku.php?id=application_binary_interface
6354 ==> U-Boot will use P3 to hold a pointer to the global data
6356 On ARM, the following registers are used:
6358 R0: function argument word/integer result
6359 R1-R3: function argument word
6360 R9: platform specific
6361 R10: stack limit (used only if stack checking is enabled)
6362 R11: argument (frame) pointer
6363 R12: temporary workspace
6366 R15: program counter
6368 ==> U-Boot will use R9 to hold a pointer to the global data
6370 Note: on ARM, only R_ARM_RELATIVE relocations are supported.
6372 On Nios II, the ABI is documented here:
6373 http://www.altera.com/literature/hb/nios2/n2cpu_nii51016.pdf
6375 ==> U-Boot will use gp to hold a pointer to the global data
6377 Note: on Nios II, we give "-G0" option to gcc and don't use gp
6378 to access small data sections, so gp is free.
6380 On NDS32, the following registers are used:
6382 R0-R1: argument/return
6384 R15: temporary register for assembler
6385 R16: trampoline register
6386 R28: frame pointer (FP)
6387 R29: global pointer (GP)
6388 R30: link register (LP)
6389 R31: stack pointer (SP)
6390 PC: program counter (PC)
6392 ==> U-Boot will use R10 to hold a pointer to the global data
6394 NOTE: DECLARE_GLOBAL_DATA_PTR must be used with file-global scope,
6395 or current versions of GCC may "optimize" the code too much.
6400 U-Boot runs in system state and uses physical addresses, i.e. the
6401 MMU is not used either for address mapping nor for memory protection.
6403 The available memory is mapped to fixed addresses using the memory
6404 controller. In this process, a contiguous block is formed for each
6405 memory type (Flash, SDRAM, SRAM), even when it consists of several
6406 physical memory banks.
6408 U-Boot is installed in the first 128 kB of the first Flash bank (on
6409 TQM8xxL modules this is the range 0x40000000 ... 0x4001FFFF). After
6410 booting and sizing and initializing DRAM, the code relocates itself
6411 to the upper end of DRAM. Immediately below the U-Boot code some
6412 memory is reserved for use by malloc() [see CONFIG_SYS_MALLOC_LEN
6413 configuration setting]. Below that, a structure with global Board
6414 Info data is placed, followed by the stack (growing downward).
6416 Additionally, some exception handler code is copied to the low 8 kB
6417 of DRAM (0x00000000 ... 0x00001FFF).
6419 So a typical memory configuration with 16 MB of DRAM could look like
6422 0x0000 0000 Exception Vector code
6425 0x0000 2000 Free for Application Use
6431 0x00FB FF20 Monitor Stack (Growing downward)
6432 0x00FB FFAC Board Info Data and permanent copy of global data
6433 0x00FC 0000 Malloc Arena
6436 0x00FE 0000 RAM Copy of Monitor Code
6437 ... eventually: LCD or video framebuffer
6438 ... eventually: pRAM (Protected RAM - unchanged by reset)
6439 0x00FF FFFF [End of RAM]
6442 System Initialization:
6443 ----------------------
6445 In the reset configuration, U-Boot starts at the reset entry point
6446 (on most PowerPC systems at address 0x00000100). Because of the reset
6447 configuration for CS0# this is a mirror of the on board Flash memory.
6448 To be able to re-map memory U-Boot then jumps to its link address.
6449 To be able to implement the initialization code in C, a (small!)
6450 initial stack is set up in the internal Dual Ported RAM (in case CPUs
6451 which provide such a feature like MPC8xx or MPC8260), or in a locked
6452 part of the data cache. After that, U-Boot initializes the CPU core,
6453 the caches and the SIU.
6455 Next, all (potentially) available memory banks are mapped using a
6456 preliminary mapping. For example, we put them on 512 MB boundaries
6457 (multiples of 0x20000000: SDRAM on 0x00000000 and 0x20000000, Flash
6458 on 0x40000000 and 0x60000000, SRAM on 0x80000000). Then UPM A is
6459 programmed for SDRAM access. Using the temporary configuration, a
6460 simple memory test is run that determines the size of the SDRAM
6463 When there is more than one SDRAM bank, and the banks are of
6464 different size, the largest is mapped first. For equal size, the first
6465 bank (CS2#) is mapped first. The first mapping is always for address
6466 0x00000000, with any additional banks following immediately to create
6467 contiguous memory starting from 0.
6469 Then, the monitor installs itself at the upper end of the SDRAM area
6470 and allocates memory for use by malloc() and for the global Board
6471 Info data; also, the exception vector code is copied to the low RAM
6472 pages, and the final stack is set up.
6474 Only after this relocation will you have a "normal" C environment;
6475 until that you are restricted in several ways, mostly because you are
6476 running from ROM, and because the code will have to be relocated to a
6480 U-Boot Porting Guide:
6481 ----------------------
6483 [Based on messages by Jerry Van Baren in the U-Boot-Users mailing
6487 int main(int argc, char *argv[])
6489 sighandler_t no_more_time;
6491 signal(SIGALRM, no_more_time);
6492 alarm(PROJECT_DEADLINE - toSec (3 * WEEK));
6494 if (available_money > available_manpower) {
6495 Pay consultant to port U-Boot;
6499 Download latest U-Boot source;
6501 Subscribe to u-boot mailing list;
6504 email("Hi, I am new to U-Boot, how do I get started?");
6507 Read the README file in the top level directory;
6508 Read http://www.denx.de/twiki/bin/view/DULG/Manual;
6509 Read applicable doc/*.README;
6510 Read the source, Luke;
6511 /* find . -name "*.[chS]" | xargs grep -i <keyword> */
6514 if (available_money > toLocalCurrency ($2500))
6517 Add a lot of aggravation and time;
6519 if (a similar board exists) { /* hopefully... */
6520 cp -a board/<similar> board/<myboard>
6521 cp include/configs/<similar>.h include/configs/<myboard>.h
6523 Create your own board support subdirectory;
6524 Create your own board include/configs/<myboard>.h file;
6526 Edit new board/<myboard> files
6527 Edit new include/configs/<myboard>.h
6532 Add / modify source code;
6536 email("Hi, I am having problems...");
6538 Send patch file to the U-Boot email list;
6539 if (reasonable critiques)
6540 Incorporate improvements from email list code review;
6542 Defend code as written;
6548 void no_more_time (int sig)
6557 All contributions to U-Boot should conform to the Linux kernel
6558 coding style; see the file "Documentation/CodingStyle" and the script
6559 "scripts/Lindent" in your Linux kernel source directory.
6561 Source files originating from a different project (for example the
6562 MTD subsystem) are generally exempt from these guidelines and are not
6563 reformatted to ease subsequent migration to newer versions of those
6566 Please note that U-Boot is implemented in C (and to some small parts in
6567 Assembler); no C++ is used, so please do not use C++ style comments (//)
6570 Please also stick to the following formatting rules:
6571 - remove any trailing white space
6572 - use TAB characters for indentation and vertical alignment, not spaces
6573 - make sure NOT to use DOS '\r\n' line feeds
6574 - do not add more than 2 consecutive empty lines to source files
6575 - do not add trailing empty lines to source files
6577 Submissions which do not conform to the standards may be returned
6578 with a request to reformat the changes.
6584 Since the number of patches for U-Boot is growing, we need to
6585 establish some rules. Submissions which do not conform to these rules
6586 may be rejected, even when they contain important and valuable stuff.
6588 Please see http://www.denx.de/wiki/U-Boot/Patches for details.
6590 Patches shall be sent to the u-boot mailing list <u-boot@lists.denx.de>;
6591 see http://lists.denx.de/mailman/listinfo/u-boot
6593 When you send a patch, please include the following information with
6596 * For bug fixes: a description of the bug and how your patch fixes
6597 this bug. Please try to include a way of demonstrating that the
6598 patch actually fixes something.
6600 * For new features: a description of the feature and your
6603 * A CHANGELOG entry as plaintext (separate from the patch)
6605 * For major contributions, your entry to the CREDITS file
6607 * When you add support for a new board, don't forget to add a
6608 maintainer e-mail address to the boards.cfg file, too.
6610 * If your patch adds new configuration options, don't forget to
6611 document these in the README file.
6613 * The patch itself. If you are using git (which is *strongly*
6614 recommended) you can easily generate the patch using the
6615 "git format-patch". If you then use "git send-email" to send it to
6616 the U-Boot mailing list, you will avoid most of the common problems
6617 with some other mail clients.
6619 If you cannot use git, use "diff -purN OLD NEW". If your version of
6620 diff does not support these options, then get the latest version of
6623 The current directory when running this command shall be the parent
6624 directory of the U-Boot source tree (i. e. please make sure that
6625 your patch includes sufficient directory information for the
6628 We prefer patches as plain text. MIME attachments are discouraged,
6629 and compressed attachments must not be used.
6631 * If one logical set of modifications affects or creates several
6632 files, all these changes shall be submitted in a SINGLE patch file.
6634 * Changesets that contain different, unrelated modifications shall be
6635 submitted as SEPARATE patches, one patch per changeset.
6640 * Before sending the patch, run the MAKEALL script on your patched
6641 source tree and make sure that no errors or warnings are reported
6642 for any of the boards.
6644 * Keep your modifications to the necessary minimum: A patch
6645 containing several unrelated changes or arbitrary reformats will be
6646 returned with a request to re-formatting / split it.
6648 * If you modify existing code, make sure that your new code does not
6649 add to the memory footprint of the code ;-) Small is beautiful!
6650 When adding new features, these should compile conditionally only
6651 (using #ifdef), and the resulting code with the new feature
6652 disabled must not need more memory than the old code without your
6655 * Remember that there is a size limit of 100 kB per message on the
6656 u-boot mailing list. Bigger patches will be moderated. If they are
6657 reasonable and not too big, they will be acknowledged. But patches
6658 bigger than the size limit should be avoided.
projects / platform / kernel / u-boot.git / blob