#include "xhci.h"
#include "xhci-mvebu.h"
+#include "xhci-rcar.h"
static void xhci_plat_quirks(struct device *dev, struct xhci_hcd *xhci)
{
/* called during probe() after chip reset completes */
static int xhci_plat_setup(struct usb_hcd *hcd)
{
+ struct device_node *of_node = hcd->self.controller->of_node;
+ int ret;
+
+ if (of_device_is_compatible(of_node, "renesas,xhci-r8a7790") ||
+ of_device_is_compatible(of_node, "renesas,xhci-r8a7791")) {
+ ret = xhci_rcar_init_quirk(hcd);
+ if (ret)
+ return ret;
+ }
+
return xhci_gen_setup(hcd, xhci_plat_quirks);
}
static int xhci_plat_start(struct usb_hcd *hcd)
{
+ struct device_node *of_node = hcd->self.controller->of_node;
+
+ if (of_device_is_compatible(of_node, "renesas,xhci-r8a7790") ||
+ of_device_is_compatible(of_node, "renesas,xhci-r8a7791"))
+ xhci_rcar_start(hcd);
+
return xhci_run(hcd);
}
{ .compatible = "xhci-platform" },
{ .compatible = "marvell,armada-375-xhci"},
{ .compatible = "marvell,armada-380-xhci"},
+ { .compatible = "renesas,xhci-r8a7790"},
+ { .compatible = "renesas,xhci-r8a7791"},
{ },
};
MODULE_DEVICE_TABLE(of, usb_xhci_of_match);
--- /dev/null
+/*
+ * xHCI host controller driver for R-Car SoCs
+ *
+ * Copyright (C) 2014 Renesas Electronics Corporation
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License
+ * version 2 as published by the Free Software Foundation.
+ */
+
+#include <linux/firmware.h>
+#include <linux/module.h>
+#include <linux/platform_device.h>
+#include <linux/usb/phy.h>
+
+#include "xhci.h"
+#include "xhci-rcar.h"
+
+#define FIRMWARE_NAME "r8a779x_usb3_v1.dlmem"
+MODULE_FIRMWARE(FIRMWARE_NAME);
+
+/*** Register Offset ***/
+#define RCAR_USB3_INT_ENA 0x224 /* Interrupt Enable */
+#define RCAR_USB3_DL_CTRL 0x250 /* FW Download Control & Status */
+#define RCAR_USB3_FW_DATA0 0x258 /* FW Data0 */
+
+#define RCAR_USB3_LCLK 0xa44 /* LCLK Select */
+#define RCAR_USB3_CONF1 0xa48 /* USB3.0 Configuration1 */
+#define RCAR_USB3_CONF2 0xa5c /* USB3.0 Configuration2 */
+#define RCAR_USB3_CONF3 0xaa8 /* USB3.0 Configuration3 */
+#define RCAR_USB3_RX_POL 0xab0 /* USB3.0 RX Polarity */
+#define RCAR_USB3_TX_POL 0xab8 /* USB3.0 TX Polarity */
+
+/*** Register Settings ***/
+/* Interrupt Enable */
+#define RCAR_USB3_INT_XHC_ENA 0x00000001
+#define RCAR_USB3_INT_PME_ENA 0x00000002
+#define RCAR_USB3_INT_HSE_ENA 0x00000004
+#define RCAR_USB3_INT_ENA_VAL (RCAR_USB3_INT_XHC_ENA | \
+ RCAR_USB3_INT_PME_ENA | RCAR_USB3_INT_HSE_ENA)
+
+/* FW Download Control & Status */
+#define RCAR_USB3_DL_CTRL_ENABLE 0x00000001
+#define RCAR_USB3_DL_CTRL_FW_SUCCESS 0x00000010
+#define RCAR_USB3_DL_CTRL_FW_SET_DATA0 0x00000100
+
+/* LCLK Select */
+#define RCAR_USB3_LCLK_ENA_VAL 0x01030001
+
+/* USB3.0 Configuration */
+#define RCAR_USB3_CONF1_VAL 0x00030204
+#define RCAR_USB3_CONF2_VAL 0x00030300
+#define RCAR_USB3_CONF3_VAL 0x13802007
+
+/* USB3.0 Polarity */
+#define RCAR_USB3_RX_POL_VAL BIT(21)
+#define RCAR_USB3_TX_POL_VAL BIT(4)
+
+void xhci_rcar_start(struct usb_hcd *hcd)
+{
+ u32 temp;
+
+ if (hcd->regs != NULL) {
+ /* Interrupt Enable */
+ temp = readl(hcd->regs + RCAR_USB3_INT_ENA);
+ temp |= RCAR_USB3_INT_ENA_VAL;
+ writel(temp, hcd->regs + RCAR_USB3_INT_ENA);
+ /* LCLK Select */
+ writel(RCAR_USB3_LCLK_ENA_VAL, hcd->regs + RCAR_USB3_LCLK);
+ /* USB3.0 Configuration */
+ writel(RCAR_USB3_CONF1_VAL, hcd->regs + RCAR_USB3_CONF1);
+ writel(RCAR_USB3_CONF2_VAL, hcd->regs + RCAR_USB3_CONF2);
+ writel(RCAR_USB3_CONF3_VAL, hcd->regs + RCAR_USB3_CONF3);
+ /* USB3.0 Polarity */
+ writel(RCAR_USB3_RX_POL_VAL, hcd->regs + RCAR_USB3_RX_POL);
+ writel(RCAR_USB3_TX_POL_VAL, hcd->regs + RCAR_USB3_TX_POL);
+ }
+}
+
+static int xhci_rcar_download_firmware(struct device *dev, void __iomem *regs)
+{
+ const struct firmware *fw;
+ int retval, index, j, time;
+ int timeout = 10000;
+ u32 data, val, temp;
+
+ /* request R-Car USB3.0 firmware */
+ retval = request_firmware(&fw, FIRMWARE_NAME, dev);
+ if (retval)
+ return retval;
+
+ /* download R-Car USB3.0 firmware */
+ temp = readl(regs + RCAR_USB3_DL_CTRL);
+ temp |= RCAR_USB3_DL_CTRL_ENABLE;
+ writel(temp, regs + RCAR_USB3_DL_CTRL);
+
+ for (index = 0; index < fw->size; index += 4) {
+ /* to avoid reading beyond the end of the buffer */
+ for (data = 0, j = 3; j >= 0; j--) {
+ if ((j + index) < fw->size)
+ data |= fw->data[index + j] << (8 * j);
+ }
+ writel(data, regs + RCAR_USB3_FW_DATA0);
+ temp = readl(regs + RCAR_USB3_DL_CTRL);
+ temp |= RCAR_USB3_DL_CTRL_FW_SET_DATA0;
+ writel(temp, regs + RCAR_USB3_DL_CTRL);
+
+ for (time = 0; time < timeout; time++) {
+ val = readl(regs + RCAR_USB3_DL_CTRL);
+ if ((val & RCAR_USB3_DL_CTRL_FW_SET_DATA0) == 0)
+ break;
+ udelay(1);
+ }
+ if (time == timeout) {
+ retval = -ETIMEDOUT;
+ break;
+ }
+ }
+
+ temp = readl(regs + RCAR_USB3_DL_CTRL);
+ temp &= ~RCAR_USB3_DL_CTRL_ENABLE;
+ writel(temp, regs + RCAR_USB3_DL_CTRL);
+
+ for (time = 0; time < timeout; time++) {
+ val = readl(regs + RCAR_USB3_DL_CTRL);
+ if (val & RCAR_USB3_DL_CTRL_FW_SUCCESS) {
+ retval = 0;
+ break;
+ }
+ udelay(1);
+ }
+ if (time == timeout)
+ retval = -ETIMEDOUT;
+
+ release_firmware(fw);
+
+ return retval;
+}
+
+/* This function needs to initialize a "phy" of usb before */
+int xhci_rcar_init_quirk(struct usb_hcd *hcd)
+{
+ /* If hcd->regs is NULL, we don't just call the following function */
+ if (!hcd->regs)
+ return 0;
+
+ return xhci_rcar_download_firmware(hcd->self.controller, hcd->regs);
+}
projects / platform / kernel / linux-stable.git / commitdiff