platform/kernel/u-boot.git
15 years ago85xx/86xx: Ensure MP boot page is not used
Kumar Gala [Tue, 31 Mar 2009 22:58:13 +0000 (17:58 -0500)]
85xx/86xx: Ensure MP boot page is not used

We had a bug on 86xx in which the boot page used to bring up secondary
cores was being overwritten and used for the malloc region in u-boot.

We need to reserve the region of memory that the boot page is going to
be put at so nothing uses it.

Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Acked-by: Becky Bruce <beckyb@kernel.crashing.org>
15 years ago85xx: Introduce determine_mp_bootpg() helper.
Kumar Gala [Wed, 1 Apr 2009 04:11:05 +0000 (23:11 -0500)]
85xx: Introduce determine_mp_bootpg() helper.

Match determine_mp_bootpg() that was added for 86xx.  We need this to
address a bug introduced in v2009.03 with 86xx MP booting.  We have to
make sure to reserve the region of memory used for the MP bootpg() so
other u-boot code doesn't use it.

Also added a comment about how cpu_reset() is dealing w/an errata on
early 85xx MP HW.

Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
15 years ago86xx: Cleanup MP support
Kumar Gala [Wed, 1 Apr 2009 04:02:38 +0000 (23:02 -0500)]
86xx: Cleanup MP support

* Use CONFIG_MP instead of CONFIG_NUM_CPUS to match 85xx
* Introduce determine_mp_bootpg() helper.  We'll need this to address a
  bug introduced in v2009.03 with 86xx MP booting.  We have to make sure
  to reserve the region of memory used for the MP bootpg() so other
  u-boot code doesn't use it.
* Added dummy versions of cpu_reset(), cpu_status() & cpu_release() to
  allow cmd_mp.c to build and work. In the future we should look at
  implementing all these functions. This could be common w/85xx if we
  use spin tables on 86xx.

Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
15 years agompc8641hpcn/sbc8641d: Add missing board_lmb_reserves
Becky Bruce [Tue, 31 Mar 2009 23:38:37 +0000 (18:38 -0500)]
mpc8641hpcn/sbc8641d: Add missing board_lmb_reserves

We're missing the board_lmb_reserve definitions that allow
cpu_mp_lmb_reserve to be called; this means that Linux
is free to reallocate reserved pages.  Linux currently boots
because we're getting lucky - the page we've reserved is
high enough in memory that it isn't allocated by Linux
while we still need it to be in existence.

Signed-off-by: Becky Bruce <beckyb@kernel.crashing.org>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
15 years agoMPC85xx: Add MPC8569MDS board support
Haiying Wang [Fri, 27 Mar 2009 21:02:45 +0000 (17:02 -0400)]
MPC85xx: Add MPC8569MDS board support

This patch adds MPC8569MDS board support. The UART, QE UEC1 and UEC2, BRD
EEPROM on I2C2 bus, PCI express and DDR3 SPD are supported in this patch.

Signed-off-by: Haiying Wang <Haiying.Wang@freescale.com>
Signed-off-by: Hillel Avni <Hillel.Avni@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
15 years agoMPC85xx: Add MPC8569 CPU support
Haiying Wang [Fri, 27 Mar 2009 21:02:44 +0000 (17:02 -0400)]
MPC85xx: Add MPC8569 CPU support

There is a workaround for MPC8569 CPU Errata, which needs to set Bit 13 of
LBCR in 4K bootpage. We setup a temp TLB for eLBC controller in bootpage,
then invalidate it after LBCR bit 13 is set.

Signed-off-by: Haiying Wang <Haiying.Wang@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
15 years agoMPC85xx: Load and enable QE microcode patch in IRAM
Haiying Wang [Thu, 26 Mar 2009 21:01:49 +0000 (17:01 -0400)]
MPC85xx: Load and enable QE microcode patch in IRAM

For the silicon which doesn't have ROM support in QE, it always needs to load
a pre-built ucode binary to IRAM so that QE can work.

Signed-off-by: Haiying Wang <Haiying.Wang@freescale.com>
Signed-off-by: Hillel Avni <Hillel.Avni@freescale.com>
15 years ago85xx: Add support for additional e500mc features
Kumar Gala [Thu, 19 Mar 2009 14:16:10 +0000 (09:16 -0500)]
85xx: Add support for additional e500mc features

* Enable backside L2
* e500mc no longer has timebase enable in HID (moved to CCSR register)

Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
15 years agofsl-ddr: add the DDR3 SPD infrastructure
Dave Liu [Sat, 14 Mar 2009 04:48:30 +0000 (12:48 +0800)]
fsl-ddr: add the DDR3 SPD infrastructure

- support mirrored DIMMs, not support register DIMMs
- test passed on P2020DS board with MT9JSF12872AY-1G1D1
- test passed on MPC8569MDS board with MT8JSF12864HY-1G1D1

Signed-off-by: Dave Liu <daveliu@freescale.com>
Signed-off-by: Travis Wheatley <travis.wheatley@freescale.com>
15 years agofsl-ddr: Fix two bugs in the ddr infrastructure
Dave Liu [Sat, 14 Mar 2009 04:48:19 +0000 (12:48 +0800)]
fsl-ddr: Fix two bugs in the ddr infrastructure

1. wr_lat
   UM said the total write latency for DDR2 is equal to
   WR_LAT + ADD_LAT, the write latency is CL + ADD_LAT - 1.
   so, the WR_LAT = CL - 1;
2. rd_to_pre
   we missed to add the ADD_LAT for DDR2 case.

Reported-by: Joakim Tjernlund <Joakim.Tjernlund@transmode.se>
Signed-off-by: Dave Liu <daveliu@freescale.com>
15 years ago83xx: Use common LSDMR defines from asm/fsl_lbc.h
Kumar Gala [Thu, 26 Mar 2009 06:34:39 +0000 (01:34 -0500)]
83xx: Use common LSDMR defines from asm/fsl_lbc.h

Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Acked-by: Kim Phillips <kim.phillips@freescale.com>
15 years ago85xx: Use common LSDMR defines from asm/fsl_lbc.h
Kumar Gala [Thu, 26 Mar 2009 06:34:38 +0000 (01:34 -0500)]
85xx: Use common LSDMR defines from asm/fsl_lbc.h

Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
15 years agoAdd LSDMR (SDRAM Mode Register) definition on localbus
Kumar Gala [Thu, 26 Mar 2009 06:34:37 +0000 (01:34 -0500)]
Add LSDMR (SDRAM Mode Register) definition on localbus

The masks for various bit defines of LSDMR are common and thus we can
define them in one place rather than replicating them in each config.h

Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
15 years agoinka4x0: Use proper accessor macros for memory mapped registers.
Detlev Zundel [Sun, 29 Mar 2009 22:31:36 +0000 (00:31 +0200)]
inka4x0: Use proper accessor macros for memory mapped registers.

Signed-off-by: Detlev Zundel <dzu@denx.de>
15 years agoinka4x0: Add hardware diagnosis and RTC in configuration.
Detlev Zundel [Sun, 29 Mar 2009 22:31:35 +0000 (00:31 +0200)]
inka4x0: Add hardware diagnosis and RTC in configuration.

This patch adds the board specific communication routines needed by
the external 4543 RTC.

Signed-off-by: Detlev Zundel <dzu@denx.de>
Signed-off-by: Andreas Pfefferle <ap@denx.de>
15 years agoinka4x0: Add hardware diagnosis functions for inka4x0
Detlev Zundel [Sun, 29 Mar 2009 22:31:34 +0000 (00:31 +0200)]
inka4x0: Add hardware diagnosis functions for inka4x0

This patch adds advanced diagnosis functions for the inka4x0 board.

Signed-off-by: Andreas Pfefferle <ap@denx.de>
Signed-off-by: Detlev Zundel <dzu@denx.de>
15 years agortc: add support for 4543 RTC (manufactured by e.g. EPSON)
Detlev Zundel [Sun, 29 Mar 2009 22:31:33 +0000 (00:31 +0200)]
rtc: add support for 4543 RTC (manufactured by e.g. EPSON)

Signed-off-by: Detlev Zundel <dzu@denx.de>
Signed-off-by: Andreas Pfefferle <ap@denx.de>
15 years agodrivers/twserial: Add protocol driver for "three wire serial" interface.
Detlev Zundel [Sun, 29 Mar 2009 22:31:32 +0000 (00:31 +0200)]
drivers/twserial: Add protocol driver for "three wire serial" interface.

This pretty unintelligent interface is used on some RTC chips.

Signed-off-by: Detlev Zundel <dzu@denx.de>
15 years agoVCMA9: fix compile errors
Wolfgang Denk [Sat, 28 Mar 2009 23:58:16 +0000 (00:58 +0100)]
VCMA9: fix compile errors

Fix these:
cmd_vcma9.c:82: warning: implicit declaration of function 'eth_getenv_enetaddr'
cmd_vcma9.c:89: error: 'enetaddr' undeclared (first use in this function)

Signed-off-by: Wolfgang Denk <wd@denx.de>
15 years agoARM: fix warning: 'print_eth' defined but not used
Wolfgang Denk [Sat, 28 Mar 2009 23:54:21 +0000 (00:54 +0100)]
ARM: fix warning: 'print_eth' defined but not used

This warning got issued for all ARM systems that don't have
CONFIG_CMD_NET enabled.

Signed-off-by: Wolfgang Denk <wd@denx.de>
15 years agocs8900 compile fix
Ladislav Michl [Mon, 23 Mar 2009 17:16:34 +0000 (18:16 +0100)]
cs8900 compile fix

cs8900.c: In function 'eth_init':
cs8900.c:164: warning: passing argument 2 of 'eth_getenv_enetaddr' from incompatible pointer type
cs8900.c:165: error: invalid operands to binary <<
cs8900.c:166: error: invalid operands to binary <<
cs8900.c:167: error: invalid operands to binary <<

Signed-off-by: Ladislav Michl <ladis@linux-mips.org>
Acked-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
15 years agoFix implicit declaration of function 'eth_[gs]etenv_enetaddr'
Wolfgang Denk [Sat, 28 Mar 2009 19:16:16 +0000 (20:16 +0100)]
Fix implicit declaration of function 'eth_[gs]etenv_enetaddr'

...and some other compile warnings.

Signed-off-by: Wolfgang Denk <wd@denx.de>
15 years agompc8xx/ether.c: fix warning: unused variable 'bd'
Wolfgang Denk [Sat, 28 Mar 2009 15:17:29 +0000 (16:17 +0100)]
mpc8xx/ether.c: fix warning: unused variable 'bd'

Also minor coding style cleanup.

Signed-off-by: Wolfgang Denk <wd@denx.de>
15 years agocommand.c: Expose the core of do_help as _do_help to the rest of u-boot.
Detlev Zundel [Wed, 25 Mar 2009 16:27:52 +0000 (17:27 +0100)]
command.c: Expose the core of do_help as _do_help to the rest of u-boot.

Other commands implementing subcommands can reuse this code nicely.

Signed-off-by: Detlev Zundel <dzu@denx.de>
Signed-off-by: Andreas Pfefferle <ap@denx.de>
15 years agompc5xxx: Add structure definition for several more register blocks.
Detlev Zundel [Tue, 24 Mar 2009 17:02:33 +0000 (18:02 +0100)]
mpc5xxx: Add structure definition for several more register blocks.

Signed-off-by: Detlev Zundel <dzu@denx.de>
15 years agoMAINTAINERS: Add entry for 'inka4x0' board.
Detlev Zundel [Fri, 27 Mar 2009 14:03:55 +0000 (15:03 +0100)]
MAINTAINERS: Add entry for 'inka4x0' board.

Signed-off-by: Detlev Zundel <dzu@denx.de>
15 years agoMAINTAINERS: Keep list sorted.
Detlev Zundel [Fri, 27 Mar 2009 14:03:54 +0000 (15:03 +0100)]
MAINTAINERS: Keep list sorted.

Signed-off-by: Detlev Zundel <dzu@denx.de>
15 years agokaref/metrobox/xpedite1k: fix eth_setenv_enetaddr typos
Mike Frysinger [Thu, 26 Mar 2009 15:17:41 +0000 (11:17 -0400)]
karef/metrobox/xpedite1k: fix eth_setenv_enetaddr typos

The function is called "eth_setenv_enetaddr", not "eth_putenv_enetaddr".

Signed-off-by: Mike Frysinger <vapier@gentoo.org>
CC: Ben Warren <biggerbadderben@gmail.com>
15 years agoppc: cleanup compiler errors/warnings
Heiko Schocher [Thu, 26 Mar 2009 06:33:59 +0000 (07:33 +0100)]
ppc: cleanup compiler errors/warnings

Current u-boot top of tree builds with warnings/errors for
the following boards:

ads5121 cpci5200 mecp5200 v38b IAD210 MBX MBX860T NX823
RPXClassic debris PN62

following patch solves this.

Signed-off-by: Heiko Schocher <hs@denx.de>
Acked-by: Mike Frysinger <vapier@gentoo.org>
15 years agoMerge branch 'master' of git://git.denx.de/u-boot-ppc4xx
Wolfgang Denk [Thu, 26 Mar 2009 21:28:52 +0000 (22:28 +0100)]
Merge branch 'master' of git://git.denx.de/u-boot-ppc4xx

15 years agoMerge branch 'master' of git://git.denx.de/u-boot-at91
Wolfgang Denk [Thu, 26 Mar 2009 21:27:45 +0000 (22:27 +0100)]
Merge branch 'master' of git://git.denx.de/u-boot-at91

15 years agoMerge branch 'master' of git://git.denx.de/u-boot-arm
Wolfgang Denk [Thu, 26 Mar 2009 21:21:48 +0000 (22:21 +0100)]
Merge branch 'master' of git://git.denx.de/u-boot-arm

15 years agoppc4xx: Sequoia: Fix TLB reassignment in NAND booting code
Stefan Roese [Thu, 26 Mar 2009 15:14:13 +0000 (16:14 +0100)]
ppc4xx: Sequoia: Fix TLB reassignment in NAND booting code

This patch fixes a bug in the Sequoia TLB init code to reconfigure
the correct TLB (boot space) after running from RAM. This bug was
introduced with patch 4d332dbeb08f5863d1ea69d91a00c5499d3a87ed
[ppc4xx: Make Sequoia boot vxWorks] which changed the order of the
TLB in the Sequoia init.S file.

Signed-off-by: Stefan Roese <sr@denx.de>
15 years agoads5121: enable instruction cache
Wolfgang Denk [Thu, 26 Mar 2009 09:00:57 +0000 (10:00 +0100)]
ads5121: enable instruction cache

Enabling the instruction cache significantly accelerates U-Boot
operations like CRC checking, image uncompression, etc.

Kudos to Andrea Scian for pointing out.

Signed-off-by: Wolfgang Denk <wd@denx.de>
15 years agompc5200: suppress printf until console initialized
Jon Smirl [Mon, 23 Mar 2009 02:55:45 +0000 (22:55 -0400)]
mpc5200: suppress printf until console initialized

On boards which have the environment in eeprom, i2c_init() is called
before the console and RAM are initialized.
Suppress printfs until the console is initialized.

Signed-off-by: Jon Smirl <jonsmirl@gmail.com>
Acked-by: Heiko Schocher <hs@denx.de>
15 years agoMerge branch 'master' of git://git.denx.de/u-boot-blackfin
Wolfgang Denk [Wed, 25 Mar 2009 21:43:25 +0000 (22:43 +0100)]
Merge branch 'master' of git://git.denx.de/u-boot-blackfin

15 years agoARM: Add the imx31_phycore_eet board to MAKEALL
Guennadi Liakhovetski [Wed, 25 Mar 2009 10:36:50 +0000 (11:36 +0100)]
ARM: Add the imx31_phycore_eet board to MAKEALL

Signed-off-by: Guennadi Liakhovetski <lg@denx.de>
15 years agoOMAP3:Beagle: Enable mtdparts
Nishanth Menon [Wed, 25 Mar 2009 21:13:56 +0000 (22:13 +0100)]
OMAP3:Beagle: Enable mtdparts

http://www.denx.de/wiki/DULG/UBootCmdGroupFlash#UBootCmdFlMtdparts
provides a flexible way to create and maintain u-boot mtd
partitions. This allows commands such as "nand erase fs"
to work and the user no longer needs to decode the absolute
nand offsets. This patch enables this function for beagleboard

Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
15 years agoBlackfin: bf537-stamp: split post code out into dedicated post.c
Mike Frysinger [Sun, 22 Feb 2009 21:26:35 +0000 (16:26 -0500)]
Blackfin: bf537-stamp: split post code out into dedicated post.c

Signed-off-by: Mike Frysinger <vapier@gentoo.org>
15 years agoBlackfin: add support for S25FL128 parts
Mike Frysinger [Sun, 12 Oct 2008 02:51:56 +0000 (22:51 -0400)]
Blackfin: add support for S25FL128 parts

Signed-off-by: Mike Frysinger <vapier@gentoo.org>
15 years agoBlackfin: overhaul SPI flash handling to speed things up
Mike Frysinger [Sun, 12 Oct 2008 02:51:23 +0000 (22:51 -0400)]
Blackfin: overhaul SPI flash handling to speed things up

Signed-off-by: Mike Frysinger <vapier@gentoo.org>
15 years agoBlackfin: add support for SST SPI flashes
Mike Frysinger [Sun, 12 Oct 2008 02:51:05 +0000 (22:51 -0400)]
Blackfin: add support for SST SPI flashes

Signed-off-by: Mike Frysinger <vapier@gentoo.org>
15 years agoBlackfin: add hack for crappy m25p80
Mike Frysinger [Sun, 12 Oct 2008 02:50:10 +0000 (22:50 -0400)]
Blackfin: add hack for crappy m25p80

Signed-off-by: Mike Frysinger <vapier@gentoo.org>
15 years agoBlackfin: bf537-stamp: increase monitor size
Mike Frysinger [Thu, 22 Jan 2009 01:47:12 +0000 (20:47 -0500)]
Blackfin: bf537-stamp: increase monitor size

The new jffs2 code pushed the code size just over the limit, so increase
the limit a bit more.

Signed-off-by: Mike Frysinger <vapier@gentoo.org>
15 years agoBlackfin: bf537-stamp: bump default SCLK up to 125MHz
Mike Frysinger [Mon, 8 Dec 2008 21:16:11 +0000 (16:16 -0500)]
Blackfin: bf537-stamp: bump default SCLK up to 125MHz

Since all of the bf537-stamp and bf537-ezkit boards out there can handle it,
increase the speed of SCLK to 125MHz rather than 100MHz.

Signed-off-by: Mike Frysinger <vapier@gentoo.org>
15 years agoBlackfin: bf537-stamp: rewrite MAC-in-flash handling
Mike Frysinger [Sun, 12 Oct 2008 02:44:14 +0000 (22:44 -0400)]
Blackfin: bf537-stamp: rewrite MAC-in-flash handling

Use the common net eth functions to setup the env/global data with the MAC
address, and properly handle the case where CONFIG_SYS_NO_FLASH is defined.

Signed-off-by: Mike Frysinger <vapier@gentoo.org>
15 years agoBlackfin: add clkin_hz= to default kernel command line for ADI boards
Mike Frysinger [Tue, 9 Dec 2008 18:47:39 +0000 (13:47 -0500)]
Blackfin: add clkin_hz= to default kernel command line for ADI boards

Signed-off-by: Mike Frysinger <vapier@gentoo.org>
15 years agoBlackfin: bf533-stamp: bump up default clocks
Mike Frysinger [Mon, 13 Oct 2008 03:49:13 +0000 (23:49 -0400)]
Blackfin: bf533-stamp: bump up default clocks

Since the hardware can handle it, bump the default clocks from 80mhz SCLK
and 398mhz CCLK to 100mhz SCLK and 498mhz CCLK.

Signed-off-by: Mike Frysinger <vapier@gentoo.org>
15 years agoBlackfin: bf533-stamp: rewrite startup LED notifications
Mike Frysinger [Sun, 12 Oct 2008 02:40:22 +0000 (22:40 -0400)]
Blackfin: bf533-stamp: rewrite startup LED notifications

Again, don't clobber pins that we aren't actually using, and use the common
LED framework rather than our own hob-job-but-not-really-working.

Signed-off-by: Mike Frysinger <vapier@gentoo.org>
15 years agoBlackfin: unify common ADI board settings
Mike Frysinger [Sun, 1 Jun 2008 13:09:48 +0000 (09:09 -0400)]
Blackfin: unify common ADI board settings

Rather than duplicate the same ADI settings in every ADI board, create a
common ADI config header and have all ADI boards start using that.  This
will also make merging the ~10 boards I have to forward port a lot easier.

Signed-off-by: Mike Frysinger <vapier@gentoo.org>
15 years agoReduce OneNAND IPL common code
Kyungmin Park [Tue, 3 Mar 2009 00:05:53 +0000 (09:05 +0900)]
Reduce OneNAND IPL common code

OneNAND IPL has common codes for RAM init, load data, and jump to 2nd
bootloader, but it's common code used about 300~400 bytes. So board
specific codes, such as lowlevel_init, can't has enough code. It make
a difficult to implement OneNAND IPL.

his patch make this common code as small as possible. and give
lowlevel_init can have more codes.

Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
15 years agoAdd multi-chip NAND support for the TQM8548 modules
Wolfgang Grandegger [Wed, 11 Feb 2009 17:38:24 +0000 (18:38 +0100)]
Add multi-chip NAND support for the TQM8548 modules

This patches configures the NAND UPM-FSL driver with multi-chip
support for the Micron MT29F8G08FAB NAND flash memory on the
TQM8548 modules.

Signed-off-by: Wolfgang Grandegger <wg@grandegger.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
15 years agoAdd wait flags to support board/chip specific delays
Wolfgang Grandegger [Wed, 11 Feb 2009 17:38:23 +0000 (18:38 +0100)]
Add wait flags to support board/chip specific delays

The NAND flash on the TQM8548_BE modules requires a short delay after
running the UPM pattern like the MPC8360ERDK board does. The TQM8548_BE
requires a further short delay after writing out a buffer. Normally the
R/B pin should be checked, but it's not connected on the TQM8548_BE.
The corresponding Linux FSL UPM driver uses similar delay points at the
same locations. To manage these extra delays in a more general way, I
introduced the "wait_flags" field allowing the board-specific driver to
specify various types of extra delay.

Signed-off-by: Wolfgang Grandegger <wg@grandegger.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
15 years agoAdd support for TQM-specific chip select logic to FSL-UPM
Wolfgang Grandegger [Wed, 11 Feb 2009 17:38:22 +0000 (18:38 +0100)]
Add support for TQM-specific chip select logic to FSL-UPM

For the NAND chips on the TQM8548 modules, a special chip-select logic is
used. It uses dedicated address lines to be set via UPM machine address
register (mar). This patch adds such support to the FSL-UPM driver.

Signed-off-by: Wolfgang Grandegger <wg@grandegger.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
15 years agoAdd multi chip support to the FSL-UPM driver
Wolfgang Grandegger [Wed, 11 Feb 2009 17:38:21 +0000 (18:38 +0100)]
Add multi chip support to the FSL-UPM driver

This patch adds support for multi-chip NAND devices to the FSL-UPM
driver. The "dev_ready" callback of the "struct fsl_upm_nand" is now
called with the argument "chip_nr" to allow testing the proper chip
select line. The NAND support of the MPC8360ERDK is updated as well.
No other boards are currently using the FSL UPM driver.

Signed-off-by: Wolfgang Grandegger <wg@grandegger.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
15 years agoEnable multi chip support in the NAND layer
Wolfgang Grandegger [Wed, 11 Feb 2009 17:38:20 +0000 (18:38 +0100)]
Enable multi chip support in the NAND layer

This patch adds support for NAND_MAX_CHIPS to the MTD NAND layer.
Multi-chips devices are displayed as shown:

  Device 0: 2x NAND 512MiB 3,3V 8-bit, sector size 128 KiB

Signed-off-by: Wolfgang Grandegger <wg@grandegger.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
15 years agoBlackfin: put memory into self-refresh before/after programming clocks
Mike Frysinger [Sun, 12 Oct 2008 01:58:33 +0000 (21:58 -0400)]
Blackfin: put memory into self-refresh before/after programming clocks

When initializing the core clocks, stick external memory into self-refresh.
This gains us a few cool things:
 - support suspend-to-RAM with Linux
 - reprogram clocks automatically when doing "go" on u-boot.bin in RAM
 - make sure settings are stable before flashing new version
 - finally fully unify initialize startup code path between LDR/non-LDR

Signed-off-by: Mike Frysinger <vapier@gentoo.org>
15 years agoBlackfin: do not program voltage regulator on parts that do not have one
Mike Frysinger [Sun, 12 Oct 2008 01:56:08 +0000 (21:56 -0400)]
Blackfin: do not program voltage regulator on parts that do not have one

Some newer Blackfins (like the BF51x) do not have an on-chip voltage
regulator, so do not attempt to program the memory as if it does.

Signed-off-by: Mike Frysinger <vapier@gentoo.org>
15 years agoBlackfin: setup a sane default EBIU_SDBCTL for SDRAM controllers
Mike Frysinger [Sun, 1 Jun 2008 05:28:24 +0000 (01:28 -0400)]
Blackfin: setup a sane default EBIU_SDBCTL for SDRAM controllers

If the board config does not specify an explicit EBIU_SDBCTL value, set it
up with sane values based on other configuration options.

Signed-off-by: Mike Frysinger <vapier@gentoo.org>
15 years agoBlackfin: handle reboot anomaly 432
Mike Frysinger [Sat, 6 Dec 2008 23:06:58 +0000 (18:06 -0500)]
Blackfin: handle reboot anomaly 432

Workaround anomaly 432:
The bfrom_SysControl() firmware function does not clear the SIC_IWR1
register before executing the PLL programming sequence.  Therefore, any
interrupt enabled in the SIC_IWR1 register prior to the call to
bfrom_SysControl() can prematurely terminate the idle sequence required
for the PLL to relock properly. SIC_IWR0 is properly handled.

Signed-off-by: Mike Frysinger <vapier@gentoo.org>
15 years agoBlackfin: kill off LDR jump block
Mike Frysinger [Sat, 18 Oct 2008 08:04:49 +0000 (04:04 -0400)]
Blackfin: kill off LDR jump block

The Boot ROM uses EVT1 as the entry point so set that rather than having
to use a tiny jump block in the default EVT1 location.

Signed-off-by: Mike Frysinger <vapier@gentoo.org>
15 years agoBlackfin: simplify symbol_lookup() a bit
Mike Frysinger [Tue, 6 Jan 2009 15:00:48 +0000 (10:00 -0500)]
Blackfin: simplify symbol_lookup() a bit

No need to skip a byte as the symbol table handles this.

Signed-off-by: Mike Frysinger <vapier@gentoo.org>
15 years agoBlackfin: fix SIC_RVECT definition: it is 16bits, not 32bits
Mike Frysinger [Sat, 7 Feb 2009 10:43:21 +0000 (05:43 -0500)]
Blackfin: fix SIC_RVECT definition: it is 16bits, not 32bits

Signed-off-by: Mike Frysinger <vapier@gentoo.org>
15 years agoBlackfin: drop SPORT_TX read helper macros
Mike Frysinger [Sat, 7 Feb 2009 10:41:17 +0000 (05:41 -0500)]
Blackfin: drop SPORT_TX read helper macros

The SPORT_TX registers cannot be read (the hardware will trigger an error),
so drop the read helper macros.

Signed-off-by: Mike Frysinger <vapier@gentoo.org>
15 years agoBlackfin: unify duplicate CPU port definitions
Mike Frysinger [Sat, 7 Feb 2009 10:25:35 +0000 (05:25 -0500)]
Blackfin: unify duplicate CPU port definitions

Signed-off-by: Mike Frysinger <vapier@gentoo.org>
15 years agoBlackfin: drop now-unused CONFIG_SYS_BFIN_CMD_XXX
Mike Frysinger [Fri, 6 Feb 2009 05:59:50 +0000 (00:59 -0500)]
Blackfin: drop now-unused CONFIG_SYS_BFIN_CMD_XXX

With the new CONFIG_XXX system and CONFIG_CMD_XXX handling, these defines
are no longer used/needed.

Signed-off-by: Mike Frysinger <vapier@gentoo.org>
15 years agoBlackfin: print out Flash: before checking it
Mike Frysinger [Mon, 6 Oct 2008 08:01:26 +0000 (04:01 -0400)]
Blackfin: print out Flash: before checking it

If there is some problem in the flash init/checking code, it's nicer to see
the message "Flash:" before crashing.  This way the source of the problem
is a bit more straightforward.

Signed-off-by: Mike Frysinger <vapier@gentoo.org>
15 years agoBlackfin: safely flush data caches when in writeback mode
Mike Frysinger [Thu, 7 Aug 2008 19:33:09 +0000 (15:33 -0400)]
Blackfin: safely flush data caches when in writeback mode

Signed-off-by: Mike Frysinger <vapier@gentoo.org>
15 years agoBlackfin: update lockbox api according to latest documentation
Mike Frysinger [Thu, 7 Aug 2008 17:21:48 +0000 (13:21 -0400)]
Blackfin: update lockbox api according to latest documentation

Signed-off-by: Mike Frysinger <vapier@gentoo.org>
15 years agoBlackfin: mark bfin_reset static
Mike Frysinger [Sun, 12 Oct 2008 01:49:06 +0000 (21:49 -0400)]
Blackfin: mark bfin_reset static

The function is only used locally, so mark it static.

Signed-off-by: Mike Frysinger <vapier@gentoo.org>
15 years agoBlackfin: spi: there is no PORTJ_FER MMR on BF537
Sonic Zhang [Fri, 20 Mar 2009 23:28:20 +0000 (19:28 -0400)]
Blackfin: spi: there is no PORTJ_FER MMR on BF537

Since the PORTJ on the BF537 is peripheral-only (no GPIO functionality),
then there is no PORTJ_FER register for us to worry about.

Signed-off-by: Sonic Zhang <Sonic.Zhang@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
15 years agoBlackfin: fix jtag console tstc
Mike Frysinger [Tue, 17 Mar 2009 17:58:23 +0000 (13:58 -0400)]
Blackfin: fix jtag console tstc

The jtag tstc operation was checking the hardware to see if data is
available from it (which is fine for the jtag getc operation), but the
higher layers need to know whether any data is available.  Since we have
to read up to 4 bytes at a time from the hardware, the higher layers need
to know they can consume the cached bytes as well.

Signed-off-by: Mike Frysinger <vapier@gentoo.org>
15 years agoBlackfin: bf537-stamp: move CONFIG_POST handling to COBJS-$(...)
Mike Frysinger [Sun, 22 Feb 2009 21:23:41 +0000 (16:23 -0500)]
Blackfin: bf537-stamp: move CONFIG_POST handling to COBJS-$(...)

Signed-off-by: Mike Frysinger <vapier@gentoo.org>
15 years agoBlackfin: unify net-related init code
Mike Frysinger [Sun, 22 Feb 2009 21:02:27 +0000 (16:02 -0500)]
Blackfin: unify net-related init code

Unify all of the net-related init code in the common Blackfin board init
code to clean up the ifdef mess a bit.

Signed-off-by: Mike Frysinger <vapier@gentoo.org>
15 years agoBlackfin: fix SWRST/SYSCR register sizes
Mike Frysinger [Wed, 18 Feb 2009 17:51:48 +0000 (12:51 -0500)]
Blackfin: fix SWRST/SYSCR register sizes

Signed-off-by: Mike Frysinger <vapier@gentoo.org>
15 years agoBlackfin: update anomaly lists
Mike Frysinger [Wed, 18 Feb 2009 17:51:31 +0000 (12:51 -0500)]
Blackfin: update anomaly lists

Signed-off-by: Mike Frysinger <vapier@gentoo.org>
15 years agoMerge branch 'master' of git://git.denx.de/u-boot-avr32
Wolfgang Denk [Mon, 23 Mar 2009 09:41:46 +0000 (10:41 +0100)]
Merge branch 'master' of git://git.denx.de/u-boot-avr32

15 years agoMerge branch 'master' of git://git.denx.de/u-boot-cfi-flash
Wolfgang Denk [Mon, 23 Mar 2009 09:29:19 +0000 (10:29 +0100)]
Merge branch 'master' of git://git.denx.de/u-boot-cfi-flash

15 years agoMerge branch 'evk1100-prep'
Haavard Skinnemoen [Mon, 23 Mar 2009 09:22:47 +0000 (10:22 +0100)]
Merge branch 'evk1100-prep'

15 years agoMerge branch 'mimc200'
Haavard Skinnemoen [Mon, 23 Mar 2009 09:22:41 +0000 (10:22 +0100)]
Merge branch 'mimc200'

15 years agoavr32: fix cacheflush.h location introducted by d8f2aa3298610b
Jean-Christophe PLAGNIOL-VILLARD [Thu, 19 Mar 2009 17:31:38 +0000 (18:31 +0100)]
avr32: fix cacheflush.h location introducted by d8f2aa3298610b

Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
15 years agoMake flash protection work, when the environment is in EEPROM
Eric Schumann [Sat, 21 Mar 2009 13:59:34 +0000 (09:59 -0400)]
Make flash protection work, when the environment is in EEPROM

On the pcm030 the environment is located in the onboard EEPROM. But we want
to handle flash sector protection in a safe manner. So we must read the
unlock environment variable from EEPROM instead from flash.

This patch is required as long the evironment is saved into the EEPROM.

Stefan: Additional change as suggested by Wolfgang, use bigger char array
(instead of 4).

Signed-off-by: Eric Schumann <E.Schumann@phytec.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Acked-by: Wolfgang Denk <wd@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>
15 years agoAdd define for mpc5200 CDM_CLK_ENA
Jon Smirl [Sat, 21 Mar 2009 15:17:56 +0000 (11:17 -0400)]
Add define for mpc5200 CDM_CLK_ENA

Signed-off-by: Jon Smirl <jonsmirl@gmail.com>
15 years agoat91: Support for the at91sam9g20 : Atmel 400Mhz ARM 926ej-s SOC.
Nicolas Ferre [Sun, 22 Mar 2009 13:48:16 +0000 (14:48 +0100)]
at91: Support for the at91sam9g20 : Atmel 400Mhz ARM 926ej-s SOC.

AT91sam9g20 is an evolution of the at91sam9260 with a faster clock speed.

The AT91SAM9G20-EK board is an updated revision of the AT91SAM9260-EK board.
It is essentially the same, with a few minor differences.

Here is the chip page on Atmel website:
http://www.atmel.com/dyn/products/product_card.asp?part_id=4337

Signed-off-by: Justin Waters <justin.waters@timesys.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
15 years agocmc_pu2: fix implicit declaration of function 'eth_setenv_enetaddr'
Jean-Christophe PLAGNIOL-VILLARD [Sun, 22 Mar 2009 13:28:14 +0000 (14:28 +0100)]
cmc_pu2: fix implicit declaration of function 'eth_setenv_enetaddr'

Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
15 years agocmc_pu2: fix misc_init_r prototype
Jean-Christophe PLAGNIOL-VILLARD [Sun, 22 Mar 2009 13:28:13 +0000 (14:28 +0100)]
cmc_pu2: fix misc_init_r prototype

Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
15 years agoat91sam9xeek: fix soc name
Jean-Christophe PLAGNIOL-VILLARD [Sun, 11 Jan 2009 02:32:01 +0000 (03:32 +0100)]
at91sam9xeek: fix soc name

Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
15 years agoat91sam9/at91cap: move nand drivers to drivers/mtd/nand
Jean-Christophe PLAGNIOL-VILLARD [Sun, 22 Mar 2009 09:22:34 +0000 (10:22 +0100)]
at91sam9/at91cap: move nand drivers to drivers/mtd/nand

Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
15 years agoatmel/at91/boards: compile dataflash partition only when dataflash is
Jean-Christophe PLAGNIOL-VILLARD [Sat, 21 Mar 2009 20:08:01 +0000 (21:08 +0100)]
atmel/at91/boards: compile dataflash partition only when dataflash is

Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
15 years agoat91sam9/at91cap: move common macb initialisation to cpu
Jean-Christophe PLAGNIOL-VILLARD [Sat, 21 Mar 2009 20:08:00 +0000 (21:08 +0100)]
at91sam9/at91cap: move common macb initialisation to cpu

Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
15 years agoat91sam9/at91cap: move common usb host initialisation to cpu
Jean-Christophe PLAGNIOL-VILLARD [Sat, 21 Mar 2009 20:08:00 +0000 (21:08 +0100)]
at91sam9/at91cap: move common usb host initialisation to cpu

Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
15 years agoat91sam9/at91cap: move common led management to cpu
Jean-Christophe PLAGNIOL-VILLARD [Sat, 21 Mar 2009 20:08:00 +0000 (21:08 +0100)]
at91sam9/at91cap: move common led management to cpu

Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
15 years agoat91sam9/at91cap: move common spi initialisation to cpu
Jean-Christophe PLAGNIOL-VILLARD [Sat, 21 Mar 2009 20:07:59 +0000 (21:07 +0100)]
at91sam9/at91cap: move common spi initialisation to cpu

Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
15 years agoat91sam9/at91cap: move common serial initialisation to cpu
Jean-Christophe PLAGNIOL-VILLARD [Sat, 21 Mar 2009 20:07:59 +0000 (21:07 +0100)]
at91sam9/at91cap: move common serial initialisation to cpu

Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
15 years agoMerge branch 'next' of ../next
Wolfgang Denk [Sat, 21 Mar 2009 21:15:49 +0000 (22:15 +0100)]
Merge branch 'next' of ../next

15 years agoPrepare 2009.03 v2009.03
Wolfgang Denk [Sat, 21 Mar 2009 21:04:41 +0000 (22:04 +0100)]
Prepare 2009.03

Update CHANGELOG

Signed-off-by: Wolfgang Denk <wd@denx.de>
15 years agoReplaced endpoint numbers with appropriate macros in usbtty.c.
Vivek Kutal [Mon, 23 Feb 2009 16:05:11 +0000 (21:35 +0530)]
Replaced endpoint numbers with appropriate macros in usbtty.c.

Signed-off-by: Vivek Kutal <vivek.kutal@azingo.com>
Signed-off-by: Remy Bohmer <linux@bohmer.net>
15 years agoUBIFS: Missing offset relocation for compressor 'none'
Michael Lawnick [Thu, 19 Mar 2009 09:06:41 +0000 (10:06 +0100)]
UBIFS: Missing offset relocation for compressor 'none'

On systems where U-Boot is linked to another address than it really lays
(e.g. backup image), calls via function pointers must be fixed with a
'+= gd->reloc_off'.
This was not done for none_compr in ubifs_compressors_init() what leads
to system crash on ubifsmount command.

Signed-off-by: Michael Lawnick <ml.lawnick@gmx.de>
Acked-by: Stefan Roese <sr@denx.de>
15 years agoUBIFS: Add UBIFS commands
Stefan Roese [Thu, 19 Mar 2009 14:35:50 +0000 (15:35 +0100)]
UBIFS: Add UBIFS commands

This patchset adds these UBIFS related commands:

- ubifsmount
  Mount an UBIFS volume

- ubifsls
  List a directory of the mounted UBIFS volume

- ubifsload
  Load a file from the mounted UBIFS volume to memory

Signed-off-by: Stefan Roese <sr@denx.de>
15 years agoUBIFS: Implement read-only UBIFS support in U-Boot
Stefan Roese [Thu, 19 Mar 2009 14:35:05 +0000 (15:35 +0100)]
UBIFS: Implement read-only UBIFS support in U-Boot

The U-Boot UBIFS implementation is largely a direct copy from the current
Linux version (2.6.29-rc6). As already done in the UBI version we have an
"abstraction layer" to redefine or remove some OS calls (e.g. mutex_lock()
...). This makes it possible to use the original Linux code with very
little changes. And by this we can better update to later Linux versions.

I removed some of the Linux features that are not used in the U-Boot
version (e.g. garbage-collection, write support).

Signed-off-by: Stefan Roese <sr@denx.de>
CC: Artem Bityutskiy <dedekind@infradead.org>
CC: Adrian Hunter <ext-Adrian.Hunter@nokia.com>