Eugeniu Rosca [Thu, 14 Mar 2019 17:31:39 +0000 (18:31 +0100)]
common: image-android-dt: Fix out-of-bounds access
Currently, 'dtimg' allows users to check indexes equal to
dt_entry_count [1]. Forbid that [2].
[1] Behavior w/o the patch:
=> ext2load mmc 0:1 0x48000000 dtb.img
105695 bytes read in 5 ms (20.2 MiB/s)
=> dtimg dump 0x48000000
dt_table_header:
magic =
d7b7ab1e
total_size = 105695
header_size = 32
dt_entry_size = 32
dt_entry_count = 2
dt_entries_offset = 32
page_size = 4096
version = 0
dt_table_entry[0]:
dt_size = 105599
dt_offset = 96
id =
0b779520
rev =
00000000
custom[0] =
00000000
custom[1] =
00000000
custom[2] =
00000000
custom[3] =
00000000
(FDT)size = 105599
(FDT)compatible = shimafuji,kingfisher
dt_table_entry[1]:
dt_size = 105599
dt_offset = 96
id =
0b779530
rev =
00000000
custom[0] =
00000000
custom[1] =
00000000
custom[2] =
00000000
custom[3] =
00000000
(FDT)size = 105599
(FDT)compatible = shimafuji,kingfisher
=> dtimg size 0x48000000 0 z; print z
z=19c7f
=> dtimg size 0x48000000 1 z; print z
z=19c7f
=> dtimg size 0x48000000 2 z; print z
z=
d00dfeed
=> dtimg size 0x48000000 3 z
Error: index > dt_entry_count (3 > 2)
[2] Behavior with the patch:
=> dtimg size 0x48000000 0 z; print z
z=19c7f
=> dtimg size 0x48000000 1 z; print z
z=19c7f
=> dtimg size 0x48000000 2 z
Error: index >= dt_entry_count (2 >= 2)
Fixes:
c04473345712 ("common: Add support for Android DT image")
Signed-off-by: Eugeniu Rosca <erosca@de.adit-jv.com>
Faiz Abbas [Thu, 14 Mar 2019 14:09:04 +0000 (19:39 +0530)]
configs: am335x_evm: Add CONFIG_BLK
With DM_MMC and DM_USB enabled, enable CONFIG_BLK.
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Masahiro Yamada [Thu, 14 Mar 2019 05:58:36 +0000 (14:58 +0900)]
Revert "Ensure device tree DTS is compiled"
This reverts commit
27cb7300ffda7a3f1581f0f5a2d3bfe59b97ad67.
I am not sure if I correctly understood the log of commit
27cb7300ffda
("Ensure device tree DTS is compiled"), but the code-diff looks like
it was trying to solve the missed re-compilation when .dts was modified.
Recently, commit
2737dfe096b6 ("kbuild: make arch-dtbs target PHONY")
fixed the issue in a more correct and more complete way.
Anyway, since the former commit, we see a clumsy log like this:
make[2]: 'arch/sandbox/dts/sandbox.dtb' is up to date
Another problem is, it created multiple paths to descend into
arch/*/dts/, causing a race in parallel building.
So, let's revert it.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Masahiro Yamada [Thu, 14 Mar 2019 05:58:35 +0000 (14:58 +0900)]
mips: add missing dtb-y to arch/mips/dts/Makefile
Since commit
27cb7300ffda ("Ensure device tree DTS is compiled"),
build succeeds irrespective of the correctness of Makefile.
In fact, you can compile any defconfig without adding any entry in
arch/*/dts/Makefile.
I am going to revert that commit, so device tree must be explicitly
listed in Makefile.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Masahiro Yamada [Thu, 14 Mar 2019 05:58:34 +0000 (14:58 +0900)]
powerpc: fix arch/powerpc/dts/Makefile
Since commit
27cb7300ffda ("Ensure device tree DTS is compiled"),
build succeeds irrespective of the correctness of Makefile.
I am going to revert that commit, so wrong code must be fixed.
CONFIG_MCR3000 is not defined anywhere. CONFIG_TARGET_MCR3000 is the
correct one.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Masahiro Yamada [Thu, 14 Mar 2019 05:58:33 +0000 (14:58 +0900)]
ARM: fix arch/arm/dts/Makefile
Since commit
27cb7300ffda ("Ensure device tree DTS is compiled"),
build succeeds irrespective of the correctness of Makefile.
In fact, you can compile any defconfig without adding any entry in
arch/*/dts/Makefile.
As a result, a lot of wrong code have been merged unnoticed.
I am going to revert that commit, and lots of hidden issues have
come to light:
[1] Typos
armada-3720-uDPU.dts, sun8i-a83t-tbs-a711.dts
use the extension ".dts" instead of ".dtb"
[2] DTB is associated to undefined CONFIG option
For example, mx6sllevk_defconfig defines CONFIG_MX6SLL, but
associates its device tree to CONFIG_MX6SL, which is undefined.
[3] Lots of entries are missing
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Chris Packham <judge.packham@gmail.com>
[trini: add imx6ul pico dtbs]
Signed-off-by: Tom Rini <trini@konsulko.com>
Abel Vesa [Tue, 12 Mar 2019 08:34:32 +0000 (08:34 +0000)]
tools: fit_image: Add the loadable property to configs
When running mkimage with "-f auto", the loadable property
needs to be set in order to allow SPL FIT support to boot.
Signed-off-by: Abel Vesa <abel.vesa@nxp.com>
Tested-by: Fabio Estevam <festevam@gmail.com>
Abel Vesa [Tue, 12 Mar 2019 08:34:31 +0000 (08:34 +0000)]
common: spl_fit: Default to IH_OS_U_BOOT if FIT_IMAGE_TINY enabled
If FIT_IMAGE_TINY is enabled, spl_fit_image_get_os returns -ENOTSUPP.
In this case, we should default to IH_OS_U_BOOT not to IH_OS_INVALID.
Signed-off-by: Abel Vesa <abel.vesa@nxp.com>
Tested-by: Fabio Estevam <festevam@gmail.com>
Alexander Graf [Wed, 20 Feb 2019 16:14:49 +0000 (17:14 +0100)]
armv8: Disable exception vectors in SPL by default
Commit
1416e2d2253 ("armv8: make SPL exception vectors optional") had a
typo in it which effectively disabled exception handling in SPL code always.
Since nobody complained, I guess we may as well disable exception handling
in SPL always by default.
So fix the bug to make the config option effective, but disable exception
handling in SPL by default. This gets us to the same functionality as before
by default, but with much less code included in the binary.
Signed-off-by: Alexander Graf <agraf@suse.de>
Reviewed-by: Matthias Brugger <mbrugger@suse.com>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Marek Vasut [Wed, 6 Mar 2019 21:04:00 +0000 (22:04 +0100)]
Makefile: Do not pass -E to mkimage when SPL has full fitImage support
When the SPL has full fitImage support, do not generate fitImage with
external data. The full fitImage code assumes the entire fitImage is
loaded in RAM, and the SPL uses fdt_totalsize() to determine the size
of the whole fitImage, which can not work with external data.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Tom Rini <trini@konsulko.com>
Heinrich Schuchardt [Thu, 28 Feb 2019 05:17:56 +0000 (06:17 +0100)]
cmd: set CONFIG_SYS_HELP_CMD_WIDTH = 10
CONFIG_SYS_HELP_CMD_WIDTH is used to format the output of help without any
arguments.
CONFIG_SYS_HELP_CMD_WIDTH = 8 is too narrow to fit all our commands.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Faiz Abbas [Tue, 26 Feb 2019 17:15:44 +0000 (22:45 +0530)]
configs: dra7xx_evm: Remove ENV_IS_IN_FAT
With U-boot supporting environment in multiple places, enable only
ENV_IS_IN_EMMC
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Keerthy [Wed, 20 Feb 2019 12:47:22 +0000 (18:17 +0530)]
arm: lib: bootm: Push the Starting kernel print to the end
Push the Starting kernel print to the end just before the
dm_remove_devices call.
Signed-off-by: Keerthy <j-keerthy@ti.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tom Rini [Thu, 21 Mar 2019 17:11:06 +0000 (13:11 -0400)]
Merge branch 'master' of git://git.denx.de/u-boot-socfpga
- ARM: socfpga: Build sfp image only for Gen5 and Arria10 devices
Tom Rini [Thu, 21 Mar 2019 17:07:42 +0000 (13:07 -0400)]
Merge tag 'efi-2019-04-rc5' of git://git.denx.de/u-boot-efi
Pull request for UEFI system for v2019.04-rc5
A bunch of small fixes. The major ones being
- avoid illegal memory access in efi_allocate_pool() on 32 bit systems
- avoid endless loop in HII protocol
Tom Rini [Thu, 21 Mar 2019 17:04:42 +0000 (13:04 -0400)]
Merge branch 'master' of git://git.denx.de/u-boot-i2c
- i2c: i2c_cdns: Fix below warnings with checker tool
Siva Durga Prasad Paladugu [Thu, 14 Mar 2019 08:18:37 +0000 (09:18 +0100)]
i2c: i2c_cdns: Fix below warnings with checker tool
This patch fixes below warnings found with checker tool.
The variable len in i2c_msg struct is of unsigned type
and it is received as recv_count which is unsigned type
but it is checked with < 0 which is always false, hence
removed it.
The local variable curr_recv_count is declared as signed
type and compared aginst unsigned recv_count which is
incorrect. This is fixed by declaring it as unsigned type.
drivers/i2c/i2c-cdns.c: In function ‘cdns_i2c_read_data’:
drivers/i2c/i2c-cdns.c:317:18: warning: comparison of
unsigned expression < 0 is always false [-Wtype-limits]
if ((recv_count < 0))
^
drivers/i2c/i2c-cdns.c:340:24: warning: comparison of
integer expressions of different signedness:
‘u32’ {aka ‘unsigned int’} and ‘int’ [-Wsign-compare]
updatetx = recv_count > curr_recv_count;
^
drivers/i2c/i2c-cdns.c:361:39: warning: comparison of
integer expressions of different signedness:
‘u32’ {aka ‘unsigned int’} and ‘int’ [-Wsign-compare]
while (readl(®s->transfer_size) !=
Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
Dalon Westergreen [Wed, 20 Mar 2019 20:15:21 +0000 (13:15 -0700)]
ARM: socfpga: Build sfp image only for Gen5 and Arria10 devices
The sfp file is only valid for Gen5 (Cyclone5 & Arria5) and Arria10
devices. The file should only be built for these devices.
Signed-off-by: Dalon Westergreen <dalon.westergreen@intel.com>
Heinrich Schuchardt [Tue, 19 Mar 2019 19:08:46 +0000 (20:08 +0100)]
efi_selftest: fix test_hii_string_get_string()
The check testing the string result of get_string() returned the wrong
result. The result was ignored.
Use efi_st_strcmp_16_8() for the string comparison.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Heinrich Schuchardt [Tue, 19 Mar 2019 18:16:23 +0000 (19:16 +0100)]
efi_loader: superfluous conversion in efi_file_open()
printf("%ls", ..) expects u16 * as argument to print. There is not need for
a conversion to wchar_t *.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Heinrich Schuchardt [Tue, 19 Mar 2019 17:58:58 +0000 (18:58 +0100)]
efi_loader: remove superfluous check in efi_setup_loaded_image()
It does not make any sense to check if a pointer is NULL if we have
dereferenced it before.
Reported-by: Coverity (CID 185827)
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Heinrich Schuchardt [Tue, 19 Mar 2019 17:44:05 +0000 (18:44 +0100)]
efi_loader: memory leak in efi_dump_single_var()
A misplaced return statement lead to a memory leak in
efi_dump_single_var().
Reported-by: Coverity (CID 185829)
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Heinrich Schuchardt [Tue, 19 Mar 2019 17:36:21 +0000 (18:36 +0100)]
efi_loader: missing return in efi_get_next_variable_name()
Add a missing return statement in efi_get_next_variable_name().
Reported-by: Coverity (CID 185834)
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Heinrich Schuchardt [Tue, 19 Mar 2019 11:30:27 +0000 (12:30 +0100)]
efi_loader: endless loop in add_strings_package()
Avoid an endless loop in add_strings_package().
Suggested-by: Takahiro Akashi <takahiro.akashi@linaro.org>
Reported-by: Coverity (CID 185833)
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Heinrich Schuchardt [Mon, 18 Mar 2019 19:01:59 +0000 (20:01 +0100)]
efi_loader: correct parameter size in efi_allocate_pool
efi_allocate_pages() expects a (uint64_t *) pointer to pass the address of
the assigned memory. If we pass the address of a pointer here, an illegal
memory access occurs on 32bit systems.
Fixes:
282a06cbcae8 ("efi_loader: Expose U-Boot addresses in memory map
for sandbox")
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Tom Rini [Tue, 19 Mar 2019 23:58:48 +0000 (19:58 -0400)]
Merge git://git.denx.de/u-boot-marvell
- Enable network interface on clearfog_gt_8k (Baruch)
- Fix dreamplug boot by adding an spi0 alias to the DT (Chris)
- Fix / enhance Marvell ddr3 setup / parameters (Chris)
- Change CONFIG_SYS_MALLOC_F_LEN to 0x2000 on db-88f6820-amc (Chris)
- Enable SPL_FLASH_BAR on db-88f6820-amc (Chris)
- Use correct pcie controller name in Armada-38x dts files (Chris)
- Disable d-cache on Kirkwood platforms as currently needed (Chris)
- Add a more descriptive comment to pci_mvebu.c (Stefan)
- Update Marvell maintainers entry (Stefan)
Tom Rini [Tue, 19 Mar 2019 11:13:23 +0000 (07:13 -0400)]
Merge branch 'master' of git://git.denx.de/u-boot-socfpga
Tom Rini [Tue, 19 Mar 2019 11:13:03 +0000 (07:13 -0400)]
Merge branch 'master' of git://git.denx.de/u-boot-usb
- Fastboot fixes
Chris Packham [Mon, 18 Mar 2019 07:51:58 +0000 (20:51 +1300)]
ARM: kirkwood: disable dcache for Kirkwood boards
Prior to commit
93b283d49f93 ("ARM: CPU: arm926ejs: Consolidate cache
routines to common file") the kirkwood boards didn't have and dcache
support. The network and usb drivers rely on this. Set
CONFIG_SYS_DCACHE_OFF in the Kirkwood specific config.h.
Reported-by: Leigh Brown <leigh@solinno.co.uk>
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>
Chris Packham [Sat, 16 Mar 2019 07:46:20 +0000 (20:46 +1300)]
ARM: mvebu: use correct name for pcie controller
When armada-385.dtsi was sync'd from Linux the name of the node
describing the pcie controller was changed from pcie-controller to pcie.
Some of the boards that include armada-385.dtsi were missed in the
update retaining the old name. This updates the affected boards.
Reported-by: Влад Мао <vlaomao@gmail.com>
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Chris Packham [Sat, 2 Mar 2019 07:45:35 +0000 (20:45 +1300)]
ARM: mvebu: db-88f6820-amc: enable SPI_FLASH_BAR
This board uses Micron N25Q256A SPI flash. Enable SPI_FLASH_BAR to allow
us to access the whole chip.
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Cc: Vignesh R <vigneshr@ti.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Chris Packham [Fri, 1 Mar 2019 01:30:03 +0000 (14:30 +1300)]
ARM: mvebu: set CONFIG_SYS_MALLOC_F_LEN to 0x2000
Set CONFIG_SYS_MALLOC_F_LEN to match the rest of the mvebu boards. The
default of 0x400 is not enough when booting from SPI.
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Chris Packham [Thu, 28 Feb 2019 21:11:14 +0000 (10:11 +1300)]
mv_ddr: ddr3: only use active chip-selects when tuning ODT
Inactive chip-selects will give invalid values for read_sample so don't
consider them when trying to determine the overall min/max read sample.
Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
[https://github.com/MarvellEmbeddedProcessors/mv-ddr-marvell/pull/18]
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Chris Packham [Thu, 28 Feb 2019 21:11:13 +0000 (10:11 +1300)]
mv_ddr: ddr3: fix tRAS timimg parameter
Based on the JEDEC standard JESD79-3F. The tRAS timings should include
the highest speed bins at a given frequency. This is similar to commit
683c67b ("mv_ddr: ddr3: fix tfaw timimg parameter") where the wrong
comparison was used in the initial implementation.
Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
[https://github.com/MarvellEmbeddedProcessors/mv-ddr-marvell/pull/15]
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Chris Packham [Thu, 28 Feb 2019 07:53:23 +0000 (20:53 +1300)]
ARM: kirkwood: add spi0 alias for dreamplug
The conversion to DM_SPI managed to break accessing the environment on
dreamplug. This is because the environment code relies on being to able
to select the SPI device based on the sequence number. Add an alias so
that the spi0 bus gets sequence number 0.
Reported-by: Leigh Brown <leigh@solinno.co.uk>
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Tested-by: Leigh Brown <leigh@solinno.co.uk>
Signed-off-by: Stefan Roese <sr@denx.de>
Stefan Roese [Fri, 15 Feb 2019 12:56:56 +0000 (13:56 +0100)]
MAINTAINERS: Update u-boot-marvell entry
This patch does the following changes to the u-boot-marvell maintainers
entry:
- Add Armada-7k/8k to the list
- Remove Prafulla and Luka since they have been silent on the list for
a long time. Please speak up, if you would like to continue or better
start maintaining.
- Add multiple Marvell / MVEBU related driver directories and files
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Prafulla Wadaskar <prafulla@marvell.com>
Cc: Luka Perkov <luka.perkov@sartura.hr>
Cc: Tom Rini <trini@konsulko.com>
Acked-by: Luka Perkov <luka.perkov@sartura.hr>
Signed-off-by: Stefan Roese <sr@denx.de>
Baruch Siach [Mon, 11 Feb 2019 12:19:55 +0000 (14:19 +0200)]
configs/clearfog_gt_8k: add network interface support
Enable the mvpp2 network driver for the Armada 8K SoC.
Enable the Marvell PHY driver for the on-board 1512 PHY.
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>
Stefan Roese [Mon, 11 Feb 2019 06:53:34 +0000 (07:53 +0100)]
pci: pci_mvebu: Add comment about missing of_n_addr_cells() call
This patch adds a comment to explain the use of the hardcoded value for
the number of address cells in mvebu_get_tgt_attr(). This should help to
rework this function, once CONFIG_OF_LIVE is enabled for MVEBU in
general.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Bin Meng <bmeng.cn@gmail.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Tom Rini [Tue, 19 Mar 2019 01:14:02 +0000 (21:14 -0400)]
Prepare v2019.04-rc4
Signed-off-by: Tom Rini <trini@konsulko.com>
Simon Goldschmidt [Fri, 15 Mar 2019 19:44:32 +0000 (20:44 +0100)]
arm: socfpga: make SPL_TEXT_BASE overridable
To boot from fpga on socfpga gen5, we need to set CONFIG_SPL_TEXT_BASE to
0xC0000000 (hps2fpgaslaves base address).
Since converting CONFIG_SPL_TEXT_BASE to Kconfig hasn't been successful so
far, let's make this value overridable in socfpga_common.h, so that we can
have different board configs override this in socfpga_common.h.
Signed-off-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Ley Foon Tan [Wed, 13 Mar 2019 03:03:35 +0000 (11:03 +0800)]
ARM: dts: socfpga: Add missing altr,sysmgr-syscon for EMAC
Syscon register is required in dts to select correct
PHY interface.
Fix error below:
Net: Failed to get syscon: -2
Signed-off-by: Ley Foon Tan <ley.foon.tan@intel.com>
Neil Armstrong [Wed, 20 Feb 2019 10:36:12 +0000 (11:36 +0100)]
fastboot: common: fix default fastboot_boot on 64-bit
When booting on a 64-bit system, the boot_addr_start buffer is not
large enough to contain a 64-bit number, thus leading to a crash
even if fastboot_buf_addr is valid, only the high part of the address
will be printed to boot_addr_start :
fastboot with fastboot_buf_addr = 0x0000000006000000:
downloading of
92239872 bytes finished
Booting kernel at 0x00000000...
"Synchronous Abort" handler, esr 0x96000004
elr:
00000000010561f4 lr :
0000000001056fac (reloc)
<snip>
x28:
000000007df2d38f x29:
000000007df2d1b0
Resetting CPU ...
With this fix, boot_addr_start can have the full 64-bit address passed
to bootm.
Fixes:
f73a7df984a9 ("net: fastboot: Merge AOSP UDP fastboot")
Cc: Simon Glass <sjg@chromium.org>
Cc: Alex Kiernan <alex.kiernan@gmail.com>
Cc: Sam Protsenko <semen.protsenko@linaro.org>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Jean-Jacques Hiblot [Thu, 24 Jan 2019 14:44:53 +0000 (15:44 +0100)]
usb: udc-uclass: Fixed problem when no alias is defined in DT
commit
801f1fa442 "dm: usb: udc: Use SEQ_ALIAS to index the USB gadget
ports" changed the way the udevice if found. It uses the alias to find
a udevice for a given USB port number. In the commit log it was stated
that if no alias is provided, the bind order will be used instead. However
it doesn't work. Fixing this by adding a call to uclass_get_device() if
uclass_get_device_by_seq() fails.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Tested-by: Vignesh R <vigneshr@ti.com>
Sean Nyekjaer [Thu, 24 Jan 2019 14:17:21 +0000 (15:17 +0100)]
cmd: fastboot: handle watchdog while waiting for fastboot commands.
Watchdog is not handled while waiting for fastboot commands.
Tested on a i.MX6 ULL EVK board.
Signed-off-by: Sean Nyekjaer <sean@geanix.com>
Tom Rini [Fri, 15 Mar 2019 15:58:17 +0000 (11:58 -0400)]
Merge git://git.denx.de/u-boot-fsl-qoriq
- DPAA2 fixes and DDR errata workaround for LS1021A
Tom Rini [Fri, 15 Mar 2019 15:58:08 +0000 (11:58 -0400)]
Merge tag 'efi-2019-04-rc4-3' of https://github.com/xypron2/u-boot
Pull request for UEFI system for v2019.04-rc4
Fix an error with the serial communication on boards with a very small
UART buffer which leads to a stalled system.
Provide an X86 reset driver for the UEFI runtime.
Fix a problem with parallel builds.
Alison Wang [Wed, 6 Mar 2019 06:49:14 +0000 (14:49 +0800)]
armv7: ls102xa: Add workaround for DDR erratum A-008850
Barrier transactions from CCI400 need to be disabled till
the DDR is configured, otherwise it may lead to system hang.
The patch adds workaround to fix the erratum.
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@nxp.com>
Signed-off-by: Alison Wang <alison.wang@nxp.com>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Pramod Kumar [Thu, 28 Feb 2019 09:06:40 +0000 (09:06 +0000)]
drivers: net: ls1088ardb: Fix EC1 and EC2 RCW offset
Fix EC1 and EC2 read from correct offset 26, instead of 25
Signed-off-by: Pramod Kumar <pramod.kumar_1@nxp.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Pankaj Bansal [Thu, 28 Feb 2019 08:12:55 +0000 (08:12 +0000)]
board: fsl: lx2160aqds: modify the phy fixup code
Now that we are representing the MDIO mux in LX2160AQDS board in
producer/consumer terms, the consumer nodes' has been changed.
Therefore, modify the device tree fixups according to change in device
tree.
Signed-off-by: Pankaj Bansal <pankaj.bansal@nxp.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Meenakshi Aggarwal [Wed, 27 Feb 2019 09:11:02 +0000 (14:41 +0530)]
mc : Reduce MC memory size to 128M
ls2088, ls1088 : minimum MC Memory size is 128 MB
lx2 : minimum MC memory size is 256 MB
Signed-off-by: Meenakshi Aggarwal <meenakshi.aggarwal@nxp.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Ioana Ciocoi Radulescu [Tue, 26 Feb 2019 15:50:07 +0000 (15:50 +0000)]
driver: net: fsl-mc: Fix DPC MAC address fixup
If node /board_info/ports does not exist in the DPC file,
function mc_fixup_dpc() will skip not only MAC address fixup,
but also the cache flush at the end. This may cause the other
fixup changes (e.g. ICID related ones) to be ignored by MC.
Fixes:
1161dbcc0a36 ("drivers: net: fsl-mc: Include MAC addr fixup to DPL")
Signed-off-by: Ioana Radulescu <ruxandra.radulescu@nxp.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Pankaj Bansal [Fri, 8 Feb 2019 08:59:24 +0000 (08:59 +0000)]
drivers: net: ldpaa_eth: check if the dpmac is enabled
some dpmacs in armv8a based freescale layerscape SOCs can be
configured via both serdes(sgmii, xfi, xlaui etc) bits and via
EC*_PMUX(rgmii) bits in RCW.
e.g. dpmac 17 and 18 in LX2160A can be configured as SGMII from
serdes bits and as RGMII via EC1_PMUX/EC2_PMUX bits
Now if a dpmac is enabled by serdes bits then it takes precedence
over EC*_PMUX bits. i.e. in LX2160A if we select serdes protocol
that configures dpmac17 as SGMII and set the EC1_PMUX as RGMII,
then the dpmac is SGMII and not RGMII.
Therefore, in fsl_rgmii_init function of SOC, we will check if the
dpmac is enabled or not? if it is (fsl_serdes_init has already enabled
the dpmac), then don't enable it.
Signed-off-by: Pankaj Bansal <pankaj.bansal@nxp.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Heinrich Schuchardt [Mon, 11 Mar 2019 21:04:51 +0000 (22:04 +0100)]
efi_loader: fix build error for freestanding.o
Since commit
f51a226436a87 ("efi_loader: provide freestanding library") in
parallel builds errors
lib/efi_selftest/../efi_loader/efi_freestanding.o:
file not recognized: File truncated
occur. Obviously make cannot correctly sequence parallel builds with a
dependency like ../efi_loader/efi_freestanding.o.
Fixes:
f51a226436a87 ("efi_loader: provide freestanding library")
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Tom Rini [Thu, 14 Mar 2019 15:37:11 +0000 (11:37 -0400)]
Merge branch 'master' of git://git.denx.de/u-boot-samsung
Krzysztof Kozlowski [Thu, 14 Mar 2019 09:53:10 +0000 (10:53 +0100)]
MAINTAINERS: Remove unsupported statuses - Odd Fixes and Obsolete
The MAINTAINERS file was copied from Linux Kernel along with all its
statuses of maintainership. However tools/genboardscfg.py accepts only
Maintained, Supported and Orphan. Remove then the Odd Fixes and
Obsolete from MAINTAINERS file to avoid confusion.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Minkyu Kang [Thu, 14 Mar 2019 00:38:41 +0000 (09:38 +0900)]
arndale: fix unknown status
set status to Maintained
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Cc: Krzysztof Kozlowski <krzk@kernel.org>
Heiko Schocher [Wed, 13 Mar 2019 11:15:45 +0000 (12:15 +0100)]
Revert "env: add spi_flash_read_env function"
This reverts commit
9a9d66f5eff0f443de4c2c6ca3e27771ed14b1b4.
because it breaks fw_setenv and U-Boot interworking, if
U-Boot environment is stored in a SPI-NOR.
Reproduce it with:
boot linux with empty Environment and store a variable
with fw_setenv into it, the Environment is now filled
with 0xff:
root@ckey5e:10:8e:~# hexdump -C /dev/mtd4
00000000 e9 e8 07 fa 01 62 6f 6f 74 63 6d 64 3d 72 75 6e |.....bootcmd=run|
[...]
00000f30 7d 00 75 62 69 62 6f 6f 74 76 6f 6c 3d 32 00 00 |}.ubibootvol=2..|
00000f40 00 ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff |................|
Boot now U-Boot prints:
Loading Environment from SPI Flash... SF: Detected s25fl128l with page size 256 Bytes, erase size 4 KiB, total 16 MiB
*** Warning - bad CRC, using default environment
Reason is the above commit, as it only reads until \0\0
is found, and assumes the rest of the Environment
space is filled with 0x00, which is not the case when
saving an Environment under linux with fw_setenv.
Signed-off-by: Heiko Schocher <hs@denx.de>
Acked-by: Stefano Babic <sbabic@denx.de>
Tom Rini [Wed, 13 Mar 2019 20:07:41 +0000 (16:07 -0400)]
Merge tag 'u-boot-imx-
20190313' of git://git.denx.de/u-boot-imx
Small fixes in several i.MX boards
----------------------------------
- imx8: add pinctrl driveri (mx8m), fix documentation and
fix reported CPU frequency. Fabio is co-maintainer
- pico-imx6ul: switch to DM
- local fixes for ventana, mx6ul_14x14_evk, engicam,
imx6(q)_logic, liteboard
Hannes Schmelzer [Fri, 15 Feb 2019 09:30:18 +0000 (10:30 +0100)]
drivers/net/fec: phy_init: remove redundant logic
The phy_connect_dev(...) function from phy.c does all the handling
(inclusive catching fixed-link).
So we drop here the single steps and call just phy_connect_dev(...).
Signed-off-by: Hannes Schmelzer <hannes.schmelzer@br-automation.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Adam Ford [Mon, 18 Feb 2019 23:58:17 +0000 (17:58 -0600)]
MTD: mxs_nand_spl: Redo the way nand_init initializes
Currently the spl system calls nand_init which does nothing.
It isn't until an attempt to load from NAND that it gets initialized.
Subsequent attempts to load just skip the initialization because
NAND is already initialized.
This moves the contents of mxs_nand_init to nand_init. In the event
of an error, it clears the number of nand chips found. Any
attempts to use nand will check if there are nand chips available
instead of actually doing the initialization at that time. If there
are none, it will return an error to the higher level calls.
Signed-off-by: Adam Ford <aford173@gmail.com>
Adam Ford [Wed, 20 Feb 2019 14:53:56 +0000 (08:53 -0600)]
arm: dts: imx6qdl-u-boot: Enable spba-bus@2000000 simple bus
spba-bus has a few nodes under it including the UART1 and
some ESPI buses. In order to use them in SPL, the
u-boot,dm-spl flag needs to be added to the spba-bus@2000000
container.
Signed-off-by: Adam Ford <aford173@gmail.com>
Adam Ford [Wed, 20 Feb 2019 04:07:22 +0000 (22:07 -0600)]
imx: serial_mxc: use CONFIG_IS_ENABLED instead of ifdef
Kconfig allows boards to configured with DM_SERIAL and still
have SPL_DM_SERIAL disabled. This patch changes the ifdef's
to CONFIG_IS_ENABLED to allow the modes to differ between
SPL and U-Boot.
Signed-off-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Adam Ford [Sun, 17 Feb 2019 14:56:00 +0000 (08:56 -0600)]
ARM: imx6q_logic: Enable MTD and NAND_MXS_DT
This patch supports enabling MTD, and the corresponding CMD_MTD
along with enabling the MXS NAND Controller with device tree
support.
Signed-off-by: Adam Ford <aford173@gmail.com>
Adam Ford [Sat, 16 Feb 2019 20:09:45 +0000 (14:09 -0600)]
ARM: imx6_logic: Fix typo in FDT address
A few scripts reference 'fdt_addr' when they should reference
'fdt_addr_r' so this patch fixes those broken references.
Signed-off-by: Adam Ford <aford173@gmail.com>
Shyam Saini [Wed, 6 Feb 2019 07:53:37 +0000 (13:23 +0530)]
include: configs: imx6-engicam: Add recovery boot option
Combined with watchdog board reset mechanism, this can be used as recovery
boot option after bootlimit exceeds the configured value.
Signed-off-by: Shyam Saini <shyam.saini@amarulasolutions.com>
Shyam Saini [Wed, 6 Feb 2019 07:53:36 +0000 (13:23 +0530)]
configs: imx6qdl_icore_mmc: Enable watchdog and bootcounter
Enable watchdog and bootcounter support on imx6qdl board
Signed-off-by: Shyam Saini <shyam.saini@amarulasolutions.com>
Shyam Saini [Wed, 6 Feb 2019 07:53:35 +0000 (13:23 +0530)]
board: engicam: Add watchdog support on Engicam
This patch adds watchdog support for engicam imx6 family
of boards.
Signed-off-by: Shyam Saini <shyam.saini@amarulasolutions.com>
Fabio Estevam [Tue, 5 Feb 2019 12:43:26 +0000 (10:43 -0200)]
imx8qxp: Fix the reported CPU frequency
Currently the CPU frequency is incorrectly reported:
CPU: NXP i.MX8QXP RevB A35 at 147228 MHz
Fix this problem by using a direct call to the SCU firmware to
retrieve the Cortex A35 CPU frequency.
With this change applied the CPU frequency is displayed correctly:
CPU: NXP i.MX8QXP RevB A35 at 1200 MHz
Tested-by: Marcelo Macedo <marcelo.macedo@nxp.com>
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Tested-by: Andrejs Cainikovs <andrejs.cainikovs@netmodule.com>
Fabio Estevam [Thu, 28 Feb 2019 11:46:15 +0000 (08:46 -0300)]
imx8mq_evk: Add myself as a co-maintainer
I would like to help maintaining this board.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Acked-by: Peng Fan <peng.fan@nxp.com>
Fabio Estevam [Thu, 28 Feb 2019 11:46:14 +0000 (08:46 -0300)]
imx8mq_evk: Move CONFIG_ENV_IS_IN_MMC to Kconfig
Currently the command "saveenv" is not available.
The CONFIG_ENV_IS_IN_MMC symbol has been converted to Kconfig,
so fix the problem by moving it to the defconfig.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Fabio Estevam [Tue, 26 Feb 2019 12:36:07 +0000 (09:36 -0300)]
mx6sabreauto: README: Adjust the binary name after DM conversion
After the conversion to DM the U-Boot binary is called u-boot-dtb.imx,
so fix the README file accordingly.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Acked-by: Peng Fan <peng.fan@nxp.com>
Fabio Estevam [Tue, 26 Feb 2019 12:36:06 +0000 (09:36 -0300)]
mx6sabresd: README: Adjust the binary name after DM conversion
After the conversion to DM the U-Boot binary is called u-boot-dtb.imx,
so fix the README file accordingly.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Acked-by: Peng Fan <peng.fan@nxp.com>
Martyn Welch [Fri, 22 Feb 2019 19:05:48 +0000 (19:05 +0000)]
imx: mx6qsabrelite: Update the SabreLite README
The information in the SabreLite README is inaccurate and sparse. The
upstream U-Boot can boot the SabreLite from SPI-NOR. Additionally, the
freely available imx_loader tool can be easily used to boot a board with a
corrupted SPI, the official Freescale/NXP manufacturing tools are not
required.
Reformat the document, adding a description of how to boot from SPI-NOR
and adding a brief description of how to recover the board should the
SPI-NOR be corrupted using imx_loader.
Signed-off-by: Martyn Welch <martyn.welch@collabora.com>
Acked-by: Troy Kisky <troy.kisky@boundarydevices.com>
Baruch Siach [Thu, 28 Feb 2019 11:51:05 +0000 (13:51 +0200)]
imx8mq_evk/README: fix DDR training firmware path
Remove a redundant directory level.
Reported-by: Ofer Heifetz <ofer.heifetz@valens.com>
Tested-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Baruch Siach [Thu, 28 Feb 2019 11:51:04 +0000 (13:51 +0200)]
imx8mq_evk/README: add missing firmware extract step
Tested-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Fabio Estevam [Thu, 14 Feb 2019 13:37:51 +0000 (11:37 -0200)]
warp7: Fix the write to the LDOGCTL PMIC register
The third parameter of the pmic_clrsetbits() function is the mask
to the register and the correct mask is 1 not 0.
Since the LDOGCTL only contains a single valid bit (bit 0),
we can use pmic_reg_write() and write 1 directly, which fixes
the problem in a simpler way and use the original pmic function
that was used prior to the DM PMIC conversion.
Fixes:
8ba377321c86 ("arm: imx7s-warp: Convert to DM PMIC")
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Fabio Estevam [Thu, 14 Feb 2019 13:35:46 +0000 (11:35 -0200)]
mx6ul_14x14_evk: Simplify the PMIC register writes
There is no need to store the values written to the PMIC inside the
'reg' variable. Make it simpler by writing the values directly.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Fabio Estevam [Thu, 14 Feb 2019 12:36:27 +0000 (10:36 -0200)]
warp7: Remove unneeded headers after DM conversion
After DM conversion the I2C and MMC related board codes have been
removed, so remove the corresponding header files as well.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Fabio Estevam [Sat, 9 Feb 2019 14:01:59 +0000 (12:01 -0200)]
warp7: README: Adjust the binary name after DM conversion
After the conversion to DM the U-Boot binary is called u-boot-dtb.imx,
so fix the README file accordingly.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Reviewed-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Tim Harvey [Thu, 21 Feb 2019 16:51:16 +0000 (08:51 -0800)]
imx: ventana: added support for 16bit 8Gb density (1GiB) DRAM
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Tim Harvey [Thu, 21 Feb 2019 16:48:48 +0000 (08:48 -0800)]
imx: ventana: hexdump invalid EEPROM data
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Marcin Niestroj [Sat, 19 Jan 2019 16:06:47 +0000 (17:06 +0100)]
ARM: liteboard: use random ethaddr
There is no ethaddr assigned to each board, so we need to use random
value in order to use network.
Signed-off-by: Marcin Niestroj <m.niestroj@grinn-global.com>
Marcin Niestroj [Sat, 19 Jan 2019 16:06:46 +0000 (17:06 +0100)]
ARM: liteboard: move towards driver model and device-tree boot
This patch mostly enables DM drivers in board defconfig and all their
dependencies. Additionally we remove USB code that is on longer
executed after enabling CONFIG_DM_USB. Enable CONFIG_PINCTRL, so we
can get rid of ethernet pin configuration.
Signed-off-by: Marcin Niestroj <m.niestroj@grinn-global.com>
Fabio Estevam [Thu, 14 Feb 2019 12:01:51 +0000 (10:01 -0200)]
pico-imx6ul: README: Adjust the binary name after DM conversion
After the conversion to DM the U-Boot binary is called u-boot-dtb.imx,
so fix the README file accordingly.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Acked-by: Otavio Salvador <otavio@ossystems.com.br>
Fabio Estevam [Thu, 14 Feb 2019 12:01:50 +0000 (10:01 -0200)]
pico-imx6ul: Convert to DM_PMIC
Convert to use DM_PMIC for the PFUZE3000. Since this PMIC is
under an I2C bus, conver to DM_I2C as well.
Also, since I2C is not used in SPL, remove CONFIG_SPL_I2C_SUPPORT
to avoid build warnings.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Acked-by: Otavio Salvador <otavio@ossystems.com.br>
Fabio Estevam [Thu, 14 Feb 2019 12:01:49 +0000 (10:01 -0200)]
pico-imx6ul: Convert to CONFIG_DM_GPIO
Convert to CONFIG_DM_GPIO.
Also, DM GPIO requires gpio_request() to be called explicitly before
doing any gpio operation, so do as requested.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Acked-by: Otavio Salvador <otavio@ossystems.com.br>
Fabio Estevam [Thu, 14 Feb 2019 12:01:48 +0000 (10:01 -0200)]
pico-imx6ul: Convert to DM MMC
Select CONFIG_DM_MMC=y in order to support MMC driver model.
This allows the MMC board related code to be removed.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Acked-by: Otavio Salvador <otavio@ossystems.com.br>
Fabio Estevam [Thu, 14 Feb 2019 12:01:47 +0000 (10:01 -0200)]
pico-imx6ul: Select CONFIG_OF_CONTROL
Select CONFIG_OF_CONTROL and the appropriate device tree files
in preparation for converting to driver model.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Acked-by: Otavio Salvador <otavio@ossystems.com.br>
Fabio Estevam [Thu, 14 Feb 2019 12:01:46 +0000 (10:01 -0200)]
pico-imx6ul: Import dts files from kernel
Import the device tree files from kernel 5.0-rc6 in preparation
for driver model conversion.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Acked-by: Otavio Salvador <otavio@ossystems.com.br>
Chris Spencer [Mon, 4 Feb 2019 10:05:34 +0000 (10:05 +0000)]
imx8mq_evk_defconfig: Enable pinctrl driver
The Ethernet controller is not able to initialise correctly without the
pinctrl driver.
This config setting was enabled in the initial version of this file,
but was removed by a savedefconfig resync because the parameter did not
actually exist at that point.
Fixes:
1bac199e8c87 ("configs: Resync with savedefconfig")
Signed-off-by: Chris Spencer <christopher.spencer@sea.co.uk>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Peng Fan [Mon, 28 Jan 2019 09:43:42 +0000 (09:43 +0000)]
pinctrl: add imx8m driver
Add i.mx8m pinctrl driver.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Tom Rini [Tue, 12 Mar 2019 14:56:02 +0000 (10:56 -0400)]
Merge tag 'efi-2019-04-rc4-2' of https://github.com/xypron2/u-boot
Pull request for UEFI system for v2019.04-rc4
Fix an error with the serial communication on boards with a very small
UART buffer which leads to a stalled system.
Provide an X86 reset driver for the UEFI runtime.
Anand Moon [Sun, 24 Feb 2019 12:41:34 +0000 (18:11 +0530)]
ARM: Odroid XU3: Enable driver I2C support for OdroidXU3
This commit enables support for I2C S3C424X0 driver.
Signed-off-by: Anand Moon <linux.amoon@gmail.com>
Acked-by: Lukasz Majewski <lukma@denx.de>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Tom Rini [Mon, 11 Mar 2019 19:48:57 +0000 (15:48 -0400)]
Merge branch 'master' of git://git.denx.de/u-boot-sunxi
- axp818 fix
- fix warnings for ethernet clock code
Tom Rini [Mon, 11 Mar 2019 15:24:20 +0000 (11:24 -0400)]
Merge git://git.denx.de/u-boot-x86
- ACPI changes and fixes to Intel Tangier/Edison
- i8254 beeper fixes
Bin Meng [Tue, 26 Feb 2019 09:52:22 +0000 (01:52 -0800)]
x86: crownbay: Enable the beeper sound driver
Use the i8254 sound driver to support creating simple beeps.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Bin Meng [Tue, 26 Feb 2019 09:52:21 +0000 (01:52 -0800)]
x86: coreboot: Add the missing pc speaker node in the device tree
This is currently missing and without it the i8254 beeper driver
won't work.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Bin Meng [Tue, 26 Feb 2019 09:52:20 +0000 (01:52 -0800)]
x86: Add a dtsi file for the pc speaker
The pc speaker driven by the i8254 is generic enough to deserve
a single dtsi file to be included by boards that use it.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Bin Meng [Tue, 26 Feb 2019 09:52:19 +0000 (01:52 -0800)]
x86: Make sure i8254 is setup correctly before generating beeps
The i8254 timer control IO port (0x43) should be setup correctly
by using PIT counter 2 to generate beeps, however in U-Boot other
codes like TSC driver utilizes PIT for TSC frequency calibration
and configures the counter 2 to a different mode that does not
beep. Fix this by always ensuring the PIT counter 2 is correctly
initialized so that the i8254 beeper driver works as expected.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Minkyu Kang [Thu, 7 Mar 2019 08:03:03 +0000 (17:03 +0900)]
espresso7420: remove duplicated config
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>