Tom Rini [Sat, 1 Apr 2023 14:55:06 +0000 (10:55 -0400)]
Merge tag 'efi-2023-04-rc6' of https://source.denx.de/u-boot/custodians/u-boot-efi
Pull request for efi-2023-04-rc6
Documentation:
* describe skipping triggering a pipeline in Gitlab
UEFI:
* correct shortening of device-paths for boot options
Heinrich Schuchardt [Sat, 1 Apr 2023 05:21:55 +0000 (07:21 +0200)]
efi_loader: remove duplicate assignment
Assigning the value of a variable to itself should be avoided.
Addresses-Coverity-ID: 451089 ("Evaluation order violation")
Fixes:
180b7118bed8 ("efi_loader: fix device-path for USB devices")
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Heinrich Schuchardt [Sun, 26 Mar 2023 10:22:40 +0000 (12:22 +0200)]
efi_loader: correct shortening of device-paths
We use short device-paths in boot options so that a file on a block device
can be found independent of the port into which the device is plugged.
Usb() device-path nodes only contain port and interface information and
therefore cannot identify a block device.
UsbWwi() device-path nodes contain the serial number of USB devices.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Heinrich Schuchardt [Sun, 26 Mar 2023 02:55:12 +0000 (02:55 +0000)]
doc: describe skipping triggering a pipeline in Gitlab
'git push -o ci.skip' can be used to push to Gitlab without triggering a
pipeline.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Heinrich Schuchardt [Sun, 26 Mar 2023 15:08:03 +0000 (17:08 +0200)]
scsi: typo supporedt
%s/supporedt/supported/
Fixes:
edca8cf72130 ("Convert CONFIG_SCSI_AHCI_PLAT et al to Kconfig")
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tom Rini [Fri, 31 Mar 2023 16:02:41 +0000 (12:02 -0400)]
Merge tag 'dm-pull-31mar23' of https://source.denx.de/u-boot/custodians/u-boot-dm
Fixes for buildman and sysreset
Jonathan Liu [Tue, 28 Mar 2023 06:44:23 +0000 (17:44 +1100)]
sysreset: gpio: fix gpio_reboot_request return value
It should return -EINPROGRESS if successful otherwise sysreset-uclass
will continue to the next sysreset device.
Signed-off-by: Jonathan Liu <net147@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Simon Glass [Mon, 27 Mar 2023 21:47:37 +0000 (10:47 +1300)]
buildman: Correct overwriting of settings file
The toolchain test causes the settings file to be overwritten, which is
annoying for local development. Fix it by passing None as the filename.
Signed-off-by: Simon Glass <sjg@chromium.org>
Fabio Estevam [Wed, 22 Mar 2023 19:59:31 +0000 (16:59 -0300)]
imx6sx-udoo-neo-basic: Introduce the u-boot.dtsi
After the conversion to DM_SERIAL in commit
01f372d8d62b ("udoo_neo:
Select DM_SERIAL and drop iomux board level init") the SPL log is gone
and the U-Boot proper log becomes incomplete:
Core: 80 devices, 18 uclasses, devicetree: separate
MMC: FSL_SDHC: 1, FSL_SDHC: 2
Loading Environment from MMC... OK
In: serial@2020000
Out: serial@2020000
Err: serial@2020000
Net: eth0: ethernet@2188000
Hit any key to stop autoboot: 0
Introduce the u-boot.dtsi file that passes the u-boot,dm-pre-reloc
properties to the relevant nodes so that UART can be used early in SPL.
With this change, the complete SPL and U-Boot messages are seen again.
Signed-off-by: Fabio Estevam <festevam@denx.de>
Tom Rini [Tue, 28 Mar 2023 14:57:34 +0000 (10:57 -0400)]
Merge branch '2023-03-28-correct-several-cli_getch-bugs'
- Merge a regression fix (for an issue that we raised post v2023.01)
with cli_getch(), and include a test now.
Simon Glass [Mon, 27 Mar 2023 19:34:14 +0000 (08:34 +1300)]
cli: Correct handling of invalid escape sequences in cread_line()
The second call to cli_ch_process() is in the wrong place, meaning that
the one of the characters of an invalid escape sequence is swallowed
instead of being returned.
Fix the bug and add a test to cover this.
This behaviour matches that of the code before cli_getch() was
introduced. This was verified on the commit before
b08e9d4b66 i.e.:
7d850f85aad ("sandbox: Enable mmc command and legacy images")
Signed-off-by: Simon Glass <sjg@chromium.org>
Reported-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Simon Glass [Mon, 27 Mar 2023 19:34:13 +0000 (08:34 +1300)]
cli: Correct several bugs in cli_getch()
This function does not behave as expected when unknown escape sequences
are sent to it:
- it fails to store (and thus echo) the last character of the invalid
sequence
- it fails to set esc_len to 0 when it finishes emitting the invalid
sequence, meaning that the following character will appear to be part
of a new escape sequence
- it processes the first character of the rejected sequence as a valid
character, just starting the sequence all over again
The last two bugs conspire to produce an "impossible condition #876"
message which is the main symptom of this behaviour.
Fix these bugs and add a test to verify the behaviour.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reported-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Tom Rini [Mon, 27 Mar 2023 18:23:26 +0000 (14:23 -0400)]
Prepare v2023.04-rc5
Signed-off-by: Tom Rini <trini@konsulko.com>
Tom Rini [Mon, 27 Mar 2023 17:39:17 +0000 (13:39 -0400)]
configs: Resync with savedefconfig
Rsync all defconfig files using moveconfig.py
Signed-off-by: Tom Rini <trini@konsulko.com>
Tom Rini [Mon, 27 Mar 2023 15:16:51 +0000 (11:16 -0400)]
Merge branch '2023-03-27-rockchip-rk3399-fixes'
- A series of minor cleanups to DISTRO_DEFAULTS and BOOTSTD so that the
rk3399 bootstd migration can be complete and functional now, and make
future migrations easier.
Tom Rini [Fri, 24 Mar 2023 20:58:16 +0000 (16:58 -0400)]
rockchip: rk3399: Drop altbootcmd
The defined altbootcmd was specific to distro_bootcmd which is not
longer in use on these platforms, so drop it.
Tested-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Jonas Karlman <jonas@kwiboo.se>
Signed-off-by: Tom Rini <trini@konsulko.com>
Tom Rini [Fri, 24 Mar 2023 20:58:15 +0000 (16:58 -0400)]
rockchip: Use BOOTSTD_DEFAULTS if not DISTRO_DEFAULTS
When we do not enable DISTRO_DEFAULTS (generally, to get distro_bootcmd)
we instea do want to imply BOOTSTD_DEFAULTS so that when using bootstd
the general distro boot functionality will still work.
Signed-off-by: Tom Rini <trini@konsulko.com>
Simon Glass [Fri, 24 Mar 2023 20:58:14 +0000 (16:58 -0400)]
rockchip: Disable DISTRO_DEFAULTS for rk3399 boards
These board have moved to standard boot but the old 'distro_bootcmd'
command is still active. Disable DISTRO_DEFAULTS to fix this.
Signed-off-by: Simon Glass <sjg@chromium.org>
Tested-by: Vagrant Cascadian <vagrant@debian.org>
Simon Glass [Fri, 24 Mar 2023 20:58:13 +0000 (16:58 -0400)]
boot: Create a common BOOT_DEFAULTS for distro and bootstd
These two features use a lot of common options. Move them into a common
CONFIG to reduce duplication.
Use 'select' for most options since these are things that boards aren't
supposed to override. For now it is not possible to disable
BOOT_DEFAULTS but we may take another look later.
Note that five options use 'imply' to match existing behaviour.
Signed-off-by: Simon Glass <sjg@chromium.org>
[trini: Rework a bit so we don't grow so many platforms unintentionally]
Signed-off-by: Tom Rini <trini@konsulko.com>
Simon Glass [Fri, 24 Mar 2023 20:58:12 +0000 (16:58 -0400)]
lmb: Enable LMB if SYS_BOOT_RAMDISK_HIGH
Ramdisk relocation requires LMB, so enable it automatically to avoid
build errors.
Signed-off-by: Simon Glass <sjg@chromium.org>
Simon Glass [Fri, 24 Mar 2023 20:58:11 +0000 (16:58 -0400)]
Move DISTRO_DEFAULTS into boot/
This relates to booting so move it in to that Kconfig file, before
changing it.
Signed-off-by: Simon Glass <sjg@chromium.org>
Simon Glass [Fri, 24 Mar 2023 20:58:10 +0000 (16:58 -0400)]
rockchip: Drop bootstage stash in TPL and SPL for rockpro64
Unfortunately the IRAM used to stash the bootstage records in TPL
becomes inaccessible after SPL runs. Presumably this is because of ATF
taking it over.
We could move the stash to another address in SPL, before passing it to
U-Boot proper. But it seems easier to wait until we have support for
standard passage[1] which should not be too far away.
For now, disable it in TPL and SPL.
[1] https://patchwork.ozlabs.org/project/uboot/cover/
20220117150428.1580273-1-sjg@chromium.org/
Signed-off-by: Simon Glass <sjg@chromium.org>
Tested-by: Vagrant Cascadian <vagrant@debian.org>
Tom Rini [Mon, 27 Mar 2023 15:05:40 +0000 (11:05 -0400)]
Merge https://source.denx.de/u-boot/custodians/u-boot-x86
- x86: Bug fixes of previous BayTrail platform CONFIG_TEXT_BASE changes
Simon Glass [Tue, 14 Mar 2023 23:59:55 +0000 (17:59 -0600)]
x86: som-db5800-som-6867: Fix up adjustment of CONFIG_TEXT_BASE
With recent CONFIG_TEXT_BASE changes, there are inconsistencies between
several settings.
Adjust CONFIG_SYS_MONITOR_LEN to allow more code space. Move the MRC
cache out of the way too.
Fixes:
e23cae30801f ("x86: som-db5800-som-6867: Adjust CONFIG_TEXT_BASE")
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Simon Glass [Tue, 14 Mar 2023 23:59:54 +0000 (17:59 -0600)]
x86: dfi-bt700: Fix up adjustment of CONFIG_TEXT_BASE
With recent CONFIG_TEXT_BASE changes, there are inconsistencies between
several settings.
Adjust CONFIG_SYS_MONITOR_LEN to allow more code space. Move the MRC
cache out of the way too.
Fixes:
5d1c8342aeaa ("x86: dfi-bt700: Adjust CONFIG_TEXT_BASE")
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Simon Glass [Tue, 14 Mar 2023 23:59:53 +0000 (17:59 -0600)]
x86: conga-qeval20-qa3-e3845: Fix up adjustment of CONFIG_TEXT_BASE
With recent CONFIG_TEXT_BASE changes, there are inconsistencies between
several settings.
Adjust CONFIG_SYS_MONITOR_LEN to allow more code space. Move the MRC
cache out of the way too.
Fixes:
388f93f96354 ("x86: conga-qeval20-qa3-e3845: Adjust CONFIG_TEXT_BASE")
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Simon Glass [Tue, 14 Mar 2023 23:59:52 +0000 (17:59 -0600)]
x86: bayleybay: Fix up adjustment of CONFIG_TEXT_BASE
With recent CONFIG_TEXT_BASE changes, there are inconsistencies between
several settings.
Adjust CONFIG_SYS_MONITOR_LEN to allow more code space. Move the MRC
cache out of the way too.
Fixes:
f38be3086837 ("x86: bayleybay: Adjust CONFIG_TEXT_BASE")
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Simon Glass [Tue, 14 Mar 2023 23:59:51 +0000 (17:59 -0600)]
x86: minnowmax: Fix up adjustment of CONFIG_TEXT_BASE
With recent CONFIG_TEXT_BASE changes, there are inconsistencies between
several settings.
Adjust CONFIG_SYS_MONITOR_LEN to allow more code space. Move the MRC
cache out of the way too.
Add documentation on how to make this change safely.
Fixes:
66e2c665f3b6 ("x86: minnowmax: Adjust CONFIG_TEXT_BASE")
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tom Rini [Sat, 25 Mar 2023 13:40:19 +0000 (09:40 -0400)]
Merge tag 'efi-2023.04-rc5' of https://source.denx.de/u-boot/custodians/u-boot-efi
Pull request for efi-2023.04-rc5
UEFI:
* Create unique device paths for USB devices with the same vendor
and product id.
Heinrich Schuchardt [Sun, 19 Mar 2023 15:18:09 +0000 (16:18 +0100)]
efi_loader: fix device-path for USB devices
EFI device paths for block devices must be unique. If a non-unique device
path is discovered, probing of the block device fails.
Currently we use UsbClass() device path nodes. As multiple devices may
have the same vendor and product id these are non-unique. Instead we
should use Usb() device path nodes. They include the USB port on the
parent hub. Hence they are unique.
A USB storage device may contain multiple logical units. These can be
modeled as Ctrl() nodes.
Reported-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Heinrich Schuchardt [Sun, 19 Mar 2023 15:18:08 +0000 (16:18 +0100)]
efi_loader: support for Ctrl() device path node
* Add the definitions for Ctrl() device path nodes.
* Implement Ctrl() nodes in the device path to text protocol.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Tom Rini [Fri, 24 Mar 2023 21:00:41 +0000 (17:00 -0400)]
Merge branch 'rpi-2023.04' of https://source.denx.de/u-boot/custodians/u-boot-raspberrypi
- Fixes for booting newer revs of the SoC in the Raspberry Pi 4
- Propagate some firmware DT properties to the loaded DT
- Update the Zero2W upstream DT name
Vincent Fazio [Tue, 14 Sep 2021 18:19:19 +0000 (13:19 -0500)]
mmc: bcm2835-host: let firmware manage the clock divisor
Newer firmware can manage the SDCDIV clock divisor register, allowing
the divisor to scale with the core as necessary.
Leverage this ability if the firmware supports it.
Adapted from the following raspberrypi Linux kernel commit:
bcm2835-sdhost: Firmware manages the clock divisor
https://github.com/raspberrypi/linux/commit/
08532d242d7702ae0add95096aa49c5e96e066e2
Signed-off-by: Vincent Fazio <vfazio@xes-inc.com>
Signed-off-by: Peter Robinson <pbrobinson@gmail.com>
Vincent Fazio [Tue, 14 Sep 2021 18:19:18 +0000 (13:19 -0500)]
arm: rpi: fallback to max clock rate for MMC clock
In rpi-firmware
25e2b597ebfb2495eab4816a276758dcc6ea21f1,
the GET_CLOCK_RATE mailbox property was changed to return the last
value set by SET_CLOCK_RATE.
https://github.com/raspberrypi/firmware/issues/1619#issuecomment-
917025502
Due to this change in firmware behavior, bcm2835_get_mmc_clock now
returns a clock rate of zero since we do not issue SET_CLOCK_RATE.
This results in degraded MMC performance.
SET_CLOCK_RATE fixes the clock to a specific value and disables scaling
so is not an ideal solution.
Instead, fallback to GET_MAX_CLOCK_RATE in bcm2835_get_mmc_clock if
GET_CLOCK_RATE returns zero.
Signed-off-by: Vincent Fazio <vfazio@xes-inc.com>
Signed-off-by: Peter Robinson <pbrobinson@gmail.com>
Tom Rini [Wed, 22 Mar 2023 18:01:01 +0000 (14:01 -0400)]
Merge branch '2023-03-22-assorted-fixes'
- Assorted TI platform fixes, correct location of NXP boot format git
repository, don't try and mount partitions that are too small to be
ext4 as ext4, handle .bin files in .gitattributes, flush out panic
messages for sure, and correct console location on Arm total_compute.
Vignesh Raghavendra [Wed, 8 Mar 2023 04:12:57 +0000 (09:42 +0530)]
dma: ti: k3-udma: Fix channel hang on teardown
Setting RX flow error handling will stall the channel until descriptors
are available to move RX data. Setting this bit causes issues when
tearing down ethernet DMA channel at the end of TFTP transfer as
unrelated network packets can cause teardown to stall indefinitely waiting
for driver to queue add more desc leading to channel hang with error
logs:
udma_stop_dev2mem TIMEOUT !
udma_stop_dev2mem: peer not stopped TIMEOUT !
udma_stop_dev2mem TIMEOUT !
Fix this by clearing rx_error_handling similar to how its done for UDMA
as part of udma_alloc_rchan_sci_req()
This fixes occasional TFTP Failures seen when downloading multiple files
one after the other on AM64/AM62 SoCs.
Fixes:
9a92851c33e8 ("dma: ti: k3-udma: Add BCDMA and PKTDMA support")
Reported-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Patrick Delaunay [Wed, 8 Mar 2023 08:49:54 +0000 (09:49 +0100)]
fs: ext4: check the minimal partition size to mount
No need to mount a too small partition to handle a EXT4 file system.
This patch add a test on partition size before to read the
SUPERBLOCK_SIZE buffer and avoid error latter in fs_devread() function.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Sebastian Andrzej Siewior [Fri, 10 Mar 2023 13:52:30 +0000 (14:52 +0100)]
gitattributes: Treat .bin files as binary.
Binary files, which are committed to a private fork of this repository,
will be subject to line feed substitution unless marked as binary.
Mark .bin files as binary.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Nikhil M Jain [Sat, 11 Mar 2023 15:54:23 +0000 (21:24 +0530)]
configs: am62x_evm_a53_defconfig: Fix SF_DEFAULT_MODE
Setting sf default mode to 0x3 breaks sf update when we do SF read
through u-boot console.
This issue arises when we do a splash image through OSPI flash media,
to fix this set the default mode to 0x0.
Fixes:
04150400c967 ("configs: enable OSPI related configs in AM62x")
Signed-off-by: Nikhil M Jain <n-jain1@ti.com>
annsai01 [Mon, 13 Mar 2023 08:57:15 +0000 (14:27 +0530)]
arm: total_compute: Remap console logs
Remapping console logs from soc uart2 (s1 terminal)
to css non-secure (uart_ap terminal)
Signed-off-by: Annam Sai Manisha <annam.saimanisha@arm.com>
Kamlesh Gurudasani [Thu, 2 Mar 2023 14:10:47 +0000 (19:40 +0530)]
configs: am62: move stack and heap to HSM RAM
On high security devices, ROM enables firewalls to protect the OCSRAM
region access during bootup. Only after TIFS has started (and had
time to disable the OCSRAM firewall region) will we have write access to
the region.
This means we will need to move the stack & heap from OCSRAM to HSM RAM
and reduce the size of BSS and the SPL to allow it to fit properly.
To protect us from overflowing our ~256k of HSM SRAM, add limits and
check during the wakeup SPL build.
Signed-off-by: Kamlesh Gurudasani <kamlesh@ti.com>
Kamlesh Gurudasani [Thu, 2 Mar 2023 14:10:46 +0000 (19:40 +0530)]
arm: mach-k3: am62: move scratch board area to HSM RAM
On high security devices, ROM enables firewalls to protect the OCSRAM
region access during bootup. Only after TIFS has started (and had
time to disable the OCSRAM firewall region) will we have write access to
the region.
So, move scratch board area to HSM RAM.
Signed-off-by: Kamlesh Gurudasani <kamlesh@ti.com>
Tony Dinh [Wed, 15 Mar 2023 00:24:26 +0000 (17:24 -0700)]
console: Use flush() before panic and reset
To make sure the panic and the reset messages will go out, console flush() should be used.
Sleep periods do not work in early u-boot phase when timer driver is not initialized yet.
Reference: https://lists.denx.de/pipermail/u-boot/2023-March/512233.html
Signed-off-by: Tony Dinh <mibodhi@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Stefan Roese <sr@denx.de>
Fabio Estevam [Fri, 13 Jan 2023 01:04:46 +0000 (22:04 -0300)]
README.mpc85xx-sd-spi-boot: Suggest the NXP boot format github repo
As explained in the text at the bottom of the page
https://source.codeaurora.org/external/qoriq/qoriq-yocto-sdk/boot-format:
"QUIC repositories on this site will not receive any updates after
March 31, 2022, and will be deleted on March 31, 2023."
Point to the NXP boot format github repo instead.
Signed-off-by: Fabio Estevam <festevam@denx.de>
Reviewed-by: Pali Rohár <pali@kernel.org>
Tom Rini [Wed, 22 Mar 2023 13:21:41 +0000 (09:21 -0400)]
Merge tag 'u-boot-amlogic-
20230322' of https://source.denx.de/u-boot/custodians/u-boot-amlogic
- odroid-go-ultra: setup PMIC regulators at board init
Tom Rini [Tue, 21 Mar 2023 15:52:55 +0000 (11:52 -0400)]
Merge branch 'master' of https://source.denx.de/u-boot/custodians/u-boot-sh
A single reset controller driver (part of the clock driver) fix
for v2023.04 release.
Tom Rini [Mon, 20 Mar 2023 21:52:42 +0000 (17:52 -0400)]
Merge tag 'u-boot-rockchip-
20230319' of https://source.denx.de/u-boot/custodians/u-boot-rockchip
- Fix for rockchip timer driver;
- Fix for rk3568 and rk3588 boot device and clock driver;
- Fix for rk3568 reset handler;
- Fix for rk3568 sdhci DLL at 52MHz;
Marek Vasut [Sat, 18 Mar 2023 11:30:53 +0000 (12:30 +0100)]
clk: renesas: Pack reset identifier before look up
The reset identifier must be processed via MOD_CLK_PACK() before it is
used to look up register and bit within reset_regs or reset_clear_regs
arrays, otherwise completely bogus register and bit is picked from the
arrays, one which may even be out of range.
Fixes:
326e05c5e21 ("clk: renesas: Add and enable CPG reset driver")
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Johan Jonker [Tue, 7 Mar 2023 15:32:00 +0000 (16:32 +0100)]
arm: dts: rockchip: rk3188-radxarock-u-boot: remove timer compatible replacement
The Rockchip timer driver has been renamed after the fall back compatible.
There's no need to replace the timer compatible in rk3188-radxarock-u-boot.dtsi
anymore, so remove.
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Johan Jonker [Tue, 7 Mar 2023 15:30:58 +0000 (16:30 +0100)]
rockchip: timer: rockchip_timer: fix compatible and driver name
In the binding for the Rockchip timer the compatible string
consists of a SoC orientated string and a fall back string
"rockchip,rk3288-timer", so remove all unneeded ones and
fix driver name.
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Vasily Khoruzhick [Thu, 9 Mar 2023 01:28:30 +0000 (17:28 -0800)]
rockchip: sdhci: rk3568: bypass DLL when clk <= 52 MHz
For Rockchip platform, DLL bypass bit and start bit need to be set if
DLL is not locked.
With this change applied eMMC in my NanoPi R5S can run at 52 MHz.
Based on linux commit
b75a52b0dda3 ("mmc: sdhci-of-dwcmshc: Update DLL
and pre-change delay for rockchip platform")
Signed-off-by: Vasily Khoruzhick <anarsoul@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Vasily Khoruzhick [Tue, 7 Mar 2023 22:08:27 +0000 (14:08 -0800)]
Revert "arm64: dts: rk356x-u-boot: Drop combphy1 assigned-clocks/rates"
This reverts commit
5bec4b0de7851a254fb4447b3599a60f95550141.
Signed-off-by: Vasily Khoruzhick <anarsoul@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Vasily Khoruzhick [Wed, 8 Mar 2023 05:16:10 +0000 (21:16 -0800)]
clk: rockchip: rk3568: add stubs for CLK_PCIEPHY_REF clocks
Device tree contains assigned-clock-rates property for these,
but default value will work just fine
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Signed-off-by: Vasily Khoruzhick <anarsoul@gmail.com>
Jonas Karlman [Tue, 14 Mar 2023 00:38:37 +0000 (00:38 +0000)]
rockchip: include: configs: Remove unused SDRAM_BANK_SIZE
Remove unused SDRAM_BANK_SIZE define.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Jonas Karlman [Tue, 14 Mar 2023 00:38:34 +0000 (00:38 +0000)]
rockchip: include: configs: Remove dangling comments
This removes dangling comments that no longer serve a purpose and has
been left after conversion of defines to Kconfig option.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Jonas Karlman [Tue, 14 Mar 2023 00:38:32 +0000 (00:38 +0000)]
mmc: rockchip_dw_mmc: Fix get_mmc_clk return value
The get_mmc_clk ops is expected to set a clock rate and return the
configured rate as an unsigned value. However, if clk_set_rate fails,
e.g. using a fixed rate clock, a negative error value is returned.
The mmc core will treat this as a valid unsigned rate and tries to
configure a divider based on this bogus clock rate.
Use 0 as the return value when setting clock rate fails, the mmc core
will configure to use bypass mode instead of using a bogus divider.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Jonas Karlman [Tue, 14 Mar 2023 00:38:31 +0000 (00:38 +0000)]
rockchip: tinker-rk3288: Use common BOOT_TARGET_DEVICES
Building U-Boot for Tinker Board with USB or NET Kconfig option disabled
result in the following build error:
In file included from include/configs/rk3288_common.h:29,
from include/configs/tinker_rk3288.h:14,
from include/config.h:3,
from include/common.h:16,
from env/common.c:10:
include/config_distro_bootcmd.h:302:9: error: expected '}' before 'BOOT_TARGET_DEVICES_references_USB_without_CONFIG_CMD_USB'
302 | BOOT_TARGET_DEVICES_references_USB_without_CONFIG_CMD_USB
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
include/config_distro_bootcmd.h:302:9: note: in definition of macro 'BOOTENV_DEV_NAME_USB'
302 | BOOT_TARGET_DEVICES_references_USB_without_CONFIG_CMD_USB
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
include/configs/tinker_rk3288.h:21:9: note: in expansion of macro 'BOOTENV_DEV_NAME'
21 | func(USB, usb, 0) \
| ^~~~
include/config_distro_bootcmd.h:454:25: note: in expansion of macro 'BOOT_TARGET_DEVICES'
454 | "boot_targets=" BOOT_TARGET_DEVICES(BOOTENV_DEV_NAME) "\0"
| ^~~~~~~~~~~~~~~~~~~
include/config_distro_bootcmd.h:474:9: note: in expansion of macro 'BOOTENV_BOOT_TARGETS'
474 | BOOTENV_BOOT_TARGETS \
| ^~~~~~~~~~~~~~~~~~~~
include/configs/rk3288_common.h:40:9: note: in expansion of macro 'BOOTENV'
40 | BOOTENV
| ^~~~~~~
include/env_default.h:122:9: note: in expansion of macro 'CFG_EXTRA_ENV_SETTINGS'
122 | CFG_EXTRA_ENV_SETTINGS
| ^~~~~~~~~~~~~~~~~~~~~~
In file included from env/common.c:32:
include/env_default.h:29:36: note: to match this '{'
29 | const char default_environment[] = {
| ^
make[2]: *** [scripts/Makefile.build:256: env/common.o] Error 1
The BOOT_TARGET_DEVICES defined in rockchip-common.h include the same
devices as defined in tinker_rk3288.h, remove the board specific one to
fix building with USB or NET option disabled.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Jonas Karlman [Tue, 14 Mar 2023 00:38:30 +0000 (00:38 +0000)]
rockchip: rk3588: Add boot device detection
Enable SPL on RK3588 to detect which device it was booted from.
Fixes use of same-as-spl in u-boot,spl-boot-order prop.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Jonas Karlman [Tue, 14 Mar 2023 00:38:27 +0000 (00:38 +0000)]
clk: rockchip: rk3588: Fix clk_aux16m in clock driver
The rate and error value is not returned for aux16m clocks, fix this.
Fixes:
7a474df74023 ("clk: rockchip: Add rk3588 clk support")
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Peter Geis [Tue, 14 Mar 2023 00:38:26 +0000 (00:38 +0000)]
clk: rockchip: rk3568: Fix reset handler
The reset handler for rk3568 is missing its private data. This leads to
an abort when a reset is triggered.
=> reset
resetting ...
"Synchronous Abort" handler, esr 0x96000045
elr:
0000000000a2bc04 lr :
0000000000a2bbd4 (reloc)
elr:
00000000eff9bc04 lr :
00000000eff9bbd4
x0 :
00000000fdd20000 x1 :
0000000014000001
x2 :
000000000000fdb9 x3 :
00000000edf77e88
x4 :
00000000edf50e78 x5 :
00000000edf77530
x6 :
000000000000001d x7 :
00000000edf8a1d0
x8 :
00000000ffffffd8 x9 :
0000000000000008
x10:
000000000000000d x11:
0000000000000006
x12:
000000000001869f x13:
0000000086c290c5
x14:
000000009118e878 x15:
0000000000000000
x16:
00000000eff9bbb8 x17:
0000000012f8c119
x18:
00000000edf50dc0 x19:
0000000000000000
x20:
0000000000000001 x21:
0000000000000000
x22:
00000000edf85900 x23:
0000000000000001
x24:
00000000effe8bbc x25:
0000000000000000
x26:
00000000edf85940 x27:
0000000000000000
x28:
0000000000000000 x29:
00000000edf3c8e0
Code:
d65f03c0 d5033fbf b9400661 529d9502 (
b8216802)
Resetting CPU ...
Add the missing dev_set_priv to the rk3568 clk driver to fix this.
Fixes:
4a262feba3a5 ("rockchip: rk3568: add clock driver")
Signed-off-by: Peter Geis <pgwipeout@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Tested-by: Jagan Teki <jagan@amarulasolutions.com> # radxa-cm3
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Jonas Karlman [Tue, 14 Mar 2023 00:38:24 +0000 (00:38 +0000)]
rockchip: rk3568-rock-3a: Sync device tree from linux
Running U-Boot from eMMC on a ROCK 3 Model A result in the following:
U-Boot SPL 2023.04-rc3 (Mar 11 2023 - 17:24:48 +0000)
Trying to boot from MMC1
Card did not respond to voltage select! : -110
spl: mmc init failed with error: -95
SPL: failed to boot from all boot devices
### ERROR ### Please RESET the board ###
The sdhci node is missing in board device tree, sync device tree from
linux v6.3-rc1 to fix booting from eMMC. Also disable sdmmc2 and uart1
nodes related to using a WiFi and BT module in the M2 slot.
Fixes:
b44c54f600ab ("arm64: dts: rockchip: rk3568: Add Radxa ROCK 3 Model A board support")
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Jonas Karlman [Tue, 14 Mar 2023 00:38:23 +0000 (00:38 +0000)]
rockchip: rk3568: Fix boot device detection
The boot source node path for emmc is using the old sdhci name.
Replace with correct mmc name and also add same-as-spl to boot order.
Fixes:
0d61f8e5f1c0 ("rockchip: rk3568: add boot device detection")
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Jonas Karlman [Tue, 14 Mar 2023 00:38:21 +0000 (00:38 +0000)]
rockchip: Fix early use of bootph props
Running U-Boot on a ROCK 3 Model A result in the following:
No serial driver found
resetting ...
no sysreset
### ERROR ### Please RESET the board ###
Replace bootph- props with u-boot,dm- props to fix this.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Tom Rini [Wed, 15 Mar 2023 16:03:17 +0000 (12:03 -0400)]
Merge branch 'master' of https://source.denx.de/u-boot/custodians/u-boot-coldfire
Tom Rini [Wed, 15 Mar 2023 16:01:55 +0000 (12:01 -0400)]
Merge branch 'master' of https://source.denx.de/u-boot/custodians/u-boot-sunxi
Per Andre:
[T]hese two patches containing just devicetree updates for
Allwinner boards.
I was still hoping for a review, since we cannot import the files from
the Linux tree verbatim, but managed to write some filter script that
convinced me that the changes are fine.
The files are from Linux v6.2-rc2, but are identical to the v6.2
release.
Angelo Dureghello [Tue, 14 Mar 2023 23:43:07 +0000 (00:43 +0100)]
board: m5253demo: remove floating point flash size calculation
This board is using floating point arithmetic to display
the SST39VF6401B flash size.
This actually generates errors with toolchains without
appropriate sw fp math functions available.
SST39VF6401B is the only flash for wich the size is displayed,
it's size is 8192KB and floating point calculation seems not
needed. Removing it.
Signed-off-by: Angelo Dureghello <angelo@kernel-space.org>
Angelo Dureghello [Tue, 14 Mar 2023 09:06:58 +0000 (10:06 +0100)]
m68k: add private libgcc ashrdi3
Add ashrdi3.c to private libgcc.
Signed-off-by: Angelo Dureghello <angelo@kernel-space.org>
Angelo Dureghello [Sat, 25 Feb 2023 23:16:39 +0000 (00:16 +0100)]
board: amcore: fix config options namespace
Remove CONFIG_ namespace options from .h, moving them to
defconfig, while changing non-defconfig options to CFG_ namespace.
Signed-off-by: Angelo Durgehello <angelo@kernel-space.org>
Angelo Dureghello [Sat, 25 Feb 2023 22:25:26 +0000 (23:25 +0100)]
m68k: rename CONFIG_MCFTMR to CFG_MCFTMR
This is not a Kconfig option so changing to _CFG.
Signed-off-by: Angelo Durgehello <angelo@kernel-space.org>
Angelo Dureghello [Wed, 15 Feb 2023 22:54:18 +0000 (23:54 +0100)]
m68k: dts: stmark2: set correct compatible field for spi nor
Fix error:
Invalid chip select 0:1 (err=-19)
update spi nor "compatible" property with "jedec,spi-nor"
to have spi nor properly bound as a child device.
Signed-off-by: Angelo Durgehello <angelo@kernel-space.org>
Angelo Dureghello [Tue, 7 Feb 2023 22:45:03 +0000 (23:45 +0100)]
arch: enable private libgcc for m68k
This patch fixes u-boot hanging on the first printf("%x", val).
Some toolchains built without multilib enabled may produce
u-boot freezing on first u64 shift operation, as in
lib/vsprintf.c number() function.
Using our private libgcc solves the issue.
Setting private libgcc enabled at architecture level to avoid
similar issues, it should not harm.
Signed-off-by: Angelo Durgehello <angelo@kernel-space.org>
Angelo Dureghello [Mon, 6 Feb 2023 21:54:37 +0000 (22:54 +0100)]
board: stmark2: fix clock value
Fix totally blank console at boot, clock value must be decimal,
as for the 30Mhz external crystal.
Fixes:
26e5944ec90c ("stmark2: Migrate CONFIG_SYS_EXTRA_OPTIONS to Kconfig")
Signed-off-by: Angelo Dureghello <angelo@kernel-space.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Angelo Dureghello [Tue, 7 Feb 2023 20:28:00 +0000 (21:28 +0100)]
m68k: add global variable sdhc_per_clk for m68k
The FSL eSDHC controller supports two reference clocks. They are
platform clock and periperhal clock. The global variable sdhc_clk
has already been used for platform clock.
ColdFire also uses eSHDC controller, as in arm and powerpc,
so adding sdhc_per_clk to arch_global_data.
Signed-off-by: Angelo Durgehello <angelo@kernel-space.org>
Angelo Dureghello [Fri, 24 Feb 2023 00:43:19 +0000 (01:43 +0100)]
m68k: use longword-based jumps
Increasing of binary size requires longword-based jumps.
Signed-off-by: Angelo Durgehello <angelo.dureghello@timesys.com>
Angelo Dureghello [Fri, 24 Feb 2023 00:42:39 +0000 (01:42 +0100)]
board: amcore: fix u-boot mtd partition
Signed-off-by: Angelo Dureghello <angelo@kernel-space.org>
Peter Robinson [Tue, 28 Feb 2023 10:17:26 +0000 (10:17 +0000)]
rpi: Update the RPi Zero 2W DT filename
Update the Raspberry Pi Zero 2W device tree file
name to match what landed upstream.
Signed-off-by: Peter Robinson <pbrobinson@gmail.com>
Antoine Mazeas [Fri, 19 Aug 2022 08:56:46 +0000 (10:56 +0200)]
rpi: Copy eth PHY address from fw DT to loaded DT
Some Raspberry Pi 400 boards, specifically rev 1.1, have a different
address for the ethernet PHY device than what is provided by the kernel
DTB. The correct address is provided by the firmware, so we should carry
it over into the loaded device tree so that ethernet works on such boards.
Signed-off-by: Antoine Mazeas <antoine@karthanis.net>
Signed-off-by: Peter Robinson <pbrobinson@gmail.com>
Antoine Mazeas [Fri, 19 Aug 2022 08:56:45 +0000 (10:56 +0200)]
rpi: Copy properties from firmware dtb to the loaded dtb
The RPI firmware adjusts several property values in the dtb it passes
to u-boot depending on the board/SoC revision. Inherit some of these
when u-boot loads a dtb itself. Specificaly copy:
* /model: The firmware provides a more specific string
* /memreserve: The firmware defines a reserved range, better keep it
* emmc2bus and pcie0 dma-ranges: The C0T revision of the bcm2711 Soc (as
present on rpi 400 and some rpi 4B boards) has different values for
these then the B0T revision. So these need to be adjusted to boot on
these boards
* blconfig: The firmware defines the memory area where the blconfig
stored. Copy those over so it can be enabled.
* /chosen/kaslr-seed: The firmware generates a kaslr seed, take advantage
of that.
Signed-off-by: Sjoerd Simons <sjoerd@collabora.com>
Signed-off-by: Antoine Mazeas <antoine@karthanis.net>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Peter Robinson <pbrobinson@gmail.com>
Neil Armstrong [Fri, 10 Feb 2023 10:25:07 +0000 (11:25 +0100)]
ARM: meson: odroid-go-ultra: setup PMIC regulators are board init
The Odroid Go Ultra has 2 chained PMICs RK818 and RK818, and needs
an adjustment on the BUCK and LDO values.
Add the initial regulators values in -u-boot.dtsi & run the initial
regulator setup in a new odroid-go-ultra board.
Proper OTG and BOOST regulators are still missing to have USB-A
host properly working.
Link: https://lore.kernel.org/r/20230210-u-boot-odroid-go-ultra-pmics-setup-v1-1-1f16d62b76af@linaro.org
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Tom Rini [Tue, 14 Mar 2023 00:52:48 +0000 (20:52 -0400)]
Prepare v2023.04-rc4
Signed-off-by: Tom Rini <trini@konsulko.com>
Tom Rini [Mon, 13 Mar 2023 15:39:21 +0000 (11:39 -0400)]
Merge tag 'efi-2023-04-rc4' of https://source.denx.de/u-boot/custodians/u-boot-efi
Pull request for efi-2023-04-rc4
Documentation:
* man-page for panic command
UEFI:
* Correct parameter check for SetVariable()
Other:
* Provide unit test for crc8
Heinrich Schuchardt [Fri, 3 Mar 2023 21:04:26 +0000 (22:04 +0100)]
efi_loader: describe term_get_char()
Add a function description.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Masahisa Kojima [Tue, 21 Feb 2023 02:33:17 +0000 (11:33 +0900)]
efi_loader: update SetVariable attribute check
UEFI specification v2.10 says that
EFI_VARIABLE_AUTHENTICATED_WRITE_ACCESS is deprecated and
EFI_UNSUPPORTED should be returned in SetVariable variable service.
Current implementation returns EFI_INVALID_PARAMETER,
let's fix the return value.
Together with above change, this commit also updates the SetVariable
attribute check to be aligned with the EDK2 reference implementation.
Signed-off-by: Masahisa Kojima <masahisa.kojima@linaro.org>
Reviewed-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Heinrich Schuchardt [Fri, 3 Mar 2023 21:48:27 +0000 (22:48 +0100)]
doc: man-page for panic command
Provide a man-page for the panic command.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Vincent Stehlé [Mon, 20 Feb 2023 14:37:29 +0000 (15:37 +0100)]
doc: uefi: fix links
Fix a couple of links so that they are rendered correctly with sphinx.
Signed-off-by: Vincent Stehlé <vincent.stehle@arm.com>
Cc: Heinrich Schuchardt <xypron.glpk@gmx.de>
Cc: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Reviewed-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Heinrich Schuchardt [Wed, 22 Feb 2023 01:10:20 +0000 (02:10 +0100)]
test: unit test for crc8
Add a unit test for the crc8() function.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tom Rini [Sat, 11 Mar 2023 00:10:14 +0000 (19:10 -0500)]
Merge https://source.denx.de/u-boot/custodians/u-boot-usb
Two minimal Kconfig/Makefile fixes for USB.
Tom Rini [Sat, 11 Mar 2023 00:09:59 +0000 (19:09 -0500)]
Merge https://source.denx.de/u-boot/custodians/u-boot-sh
Assorted Renesas fixes below, namely MMC clocking breakage fix, clock
Kconfig fix, pin control unused symbols removal, and sysinfo fix and
enablement on now fixed platforms.
Tom Rini [Fri, 10 Mar 2023 21:01:52 +0000 (16:01 -0500)]
Merge tag 'dm-pull-10mar23' of https://source.denx.de/u-boot/custodians/u-boot-dm
fixes and tests for the fdt command
Tam Nguyen [Mon, 27 Feb 2023 22:58:48 +0000 (23:58 +0100)]
ARM: dts: renesas: Enable sysinfo on R-Car D3 Draak
Enable support for sysinfo on R-Car D3 Draak board. The sysinfo is used
e.g. to access and decode board-specific information and then in turn
used by board-info to print those information.
Reviewed-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Signed-off-by: Tam Nguyen <tam.nguyen.xa@renesas.com>
Signed-off-by: Hai Pham <hai.pham.ud@renesas.com>
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
[Marek: Drop compatible from I2C node, this is in r8a77995.dtsi already.
Drop status = "okay" from EEPROM node.
Add dts: tag.
Fix Kconfig EEPROM address to be 0x50 and match the DT, sync config.]
Tam Nguyen [Mon, 27 Feb 2023 22:58:47 +0000 (23:58 +0100)]
ARM: dts: renesas: Enable sysinfo on R-Car V3H Condor/Condor-I
Add new sysinfo IDs for R-Car V3H Condor/Condor-I .
Enable support for sysinfo on R-Car V3H Condor/Condor-I. The sysinfo is
used e.g. to access and decode board-specific information and then in
turn used by board-info to print those information.
Reviewed-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Signed-off-by: Tam Nguyen <tam.nguyen.xa@renesas.com>
Signed-off-by: Hai Pham <hai.pham.ud@renesas.com>
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
[Marek: Drop compatible from I2C node, this is in r8a77980.dtsi already.
Drop status = "okay" from EEPROM node.
Add dts: tag.
Update the commit message, note the new sysinfo IDs.
Fix Kconfig EEPROM address to be 0x50 and match the DT, sync config.]
Tam Nguyen [Mon, 27 Feb 2023 22:58:46 +0000 (23:58 +0100)]
sysinfo: rcar3: Fix Draak and Eagle board code
Correct the board code ID based on the hardware documentation
Reviewed-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Signed-off-by: Tam Nguyen <tam.nguyen.xa@renesas.com>
Signed-off-by: Hai Pham <hai.pham.ud@renesas.com>
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Marek Vasut [Tue, 28 Feb 2023 06:25:53 +0000 (07:25 +0100)]
pinctrl: renesas: Drop non-existent PFC info table entries
Remove PFC info table entries which are never instantiated,
since there are no drivers for those. No functional change.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Marek Vasut [Tue, 28 Feb 2023 21:16:02 +0000 (22:16 +0100)]
clk: renesas: Always select DM_RESET to prevent inobvious failure of rst_gen3 subdriver
The CLK_RCAR_GEN3 registers two subdrivers, clk_gen3 and rst_gen3.
The former depends on the clock framework, which is always enabled
in this context of clock framework driver, while the later depends
on reset framework which may not always be enabled.
Ensure the reset framework is also always enabled to prevent inobvious
early boot time bind failure of the CPG driver, which leads to system
showing no activity and is difficult to debug.
Note that one possible approach to debug this is to use CONFIG_DEBUG_UART
and add debug printascii()s into the drivers/clk/renesas/clk-rcar-gen3.c .
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Marek Vasut [Mon, 27 Feb 2023 22:49:28 +0000 (23:49 +0100)]
mmc: renesas-sdhi: Add proper probe error fail path
In case one of the calls in probe fail, trigger a fail path and
undo all the steps done in probe until the point of failure.
The current implementation failed to stop controller clock and
free claimed clock, so fix that. Furthermore, print return code
in error prints for easier debugging.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Marek Vasut [Mon, 27 Feb 2023 22:49:27 +0000 (23:49 +0100)]
mmc: renesas-sdhi: Always configure default SDnH clock rate to 800 MHz
The prior stage bootloader might have left the SDnCKCR register in completely
arbitrary state before passing control to U-Boot, which includes the register
being populated with incorrect values. Currently the SDHI driver will attempt
to use clock framework to configure SDn clock, which may fail in case SDnCKCR
contains invalid values for the SDnH clock, because the clock framework would
not be able to determine SDnH clock rate and would get -EINVAL instead, which
in turn would not allow the clock framework to determine the correct SDn clock
divider ratio.
This failure occurs specifically in case SDnCKCR reads back 0x209 .
Correct the problem by first setting default SDnH clock rate to 800 MHz, thus
assuring the SDnCKCR SDnH bits are correct, and only afterward set up the SDn
clock rate to default 200 MHz.
Note that the SDHI driver may reconfigure SDnH clock later based on IOS
settings obtained from the attached card, the 800 MHz set up here is only
the default value.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Heinrich Schuchardt [Wed, 25 Jan 2023 18:40:16 +0000 (19:40 +0100)]
usb: move CONFIG_USB_HUB_DEBOUNCE_TIMEOUT to USB
This configuration setting is only relevant if the board supports USB.
It should not be in the main menu but in the USB menu.
The setting is only relevant in USB host mode.
Fixes:
5454dea3137d ("usb: hub: allow to increase HUB_DEBOUNCE_TIMEOUT")
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Marek Vasut <marex@denx.de>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Heinrich Schuchardt [Wed, 25 Jan 2023 18:40:15 +0000 (19:40 +0100)]
usb: USB hubs require host mode
USB hubs run in host mode not in gadget mode. Hence, compiling usb_hub.c
should not be selected by CONFIG_USB_GADGET.
Suggested-by: Marek Vasut <marex@denx.de>
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Marek Vasut <marex@denx.de>
Marek Vasut [Thu, 2 Mar 2023 03:08:40 +0000 (04:08 +0100)]
test: cmd: fdt: Test fdt bootcpu
Add 'fdt bootcpu' test which works as follows:
- Create basic FDT, map it to sysmem
- Print the FDT bootcpu
- Set the FDT bootcpu and read the value back using 'fdt header get'
- Perform the previous step twice to validate bootcpu overwrite
The test case can be triggered using:
"
./u-boot -Dc 'ut fdt'
"
To dump the full output from commands used during test, add '-v' flag.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Marek Vasut [Thu, 2 Mar 2023 03:08:38 +0000 (04:08 +0100)]
test: cmd: fdt: Test fdt rm
Add 'fdt rm' test which works as follows:
- Create fuller FDT, map it to sysmem
- Selectively delete nodes or properties by both path and aliases
- Verify created nodes or properties using fdt print command
The test case can be triggered using:
"
./u-boot -Dc 'ut fdt'
"
To dump the full output from commands used during test, add '-v' flag.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Reviewed-by: Simon Glass <sjg@chromium.org>