Wolfgang Denk [Sun, 19 Jul 2009 10:05:15 +0000 (12:05 +0200)]
pcm030: fix out-of-tree building
Commit
0a87dd90 that was supposed to fix out-of-tree building for the
pcm030 board was unfortunately incomplete.
Signed-off-by: Wolfgang Denk <wd@denx.de>
Kazuaki Ichinohe [Fri, 12 Jun 2009 09:10:12 +0000 (18:10 +0900)]
Canyonlands SATA harddisk driver
This patch adds a SATA harddisk driver for the canyonlands.
This patch is kernel driver's porting.
This patch corresponded to not cmd_scsi but cmd_sata.
This patch divided an unused member with ifndef __U_BOOT__ in the structure.
[environment variable, boot script]
setenv bootargs root=/dev/sda7 rw
setenv bootargs ${bootargs} console=ttyS0,115200
ext2load sata 0:2 0x400000 /canyonlands/uImage
ext2load sata 0:2 0x800000 /canyonlands/canyonlands.dtb
fdt addr 0x800000 0x4000
bootm 0x400000 - 0x800000
If you drive SATA-2 disk on Canyonlands, you must change parts from
PI2PCIE212 to PI2PCIE2212 on U25. We confirmed to boot by using
following disks:
1.Vendor: Fujitsu Type: MHW2040BS
2.Vendor: Fujitsu Type: MHW2060BK
3.Vendor: HAGIWARA SYS-COM:HFD25S-032GT
4.Vendor: WesternDigital Type: WD3200BJKT (CONFIG_LBA48 required)
5.Vendor: WesternDigital Type: WD3200BEVT (CONFIG_LBA48 required)
6.Vendor: Hitachi Type: HTS543232L9A300 (CONFIG_LBA48 required)
7.Vendor: Seagate Type: ST31000333AS (CONFIG_LBA48 required)
8.Vendor: Transcend Type: TS32GSSD25S-M
9.Vendor: MTRON Type: MSD-SATA1525-016
Signed-off-by: Kazuaki Ichinohe <kazuichi at fsi.co.jp>
Reinhard Arlt [Wed, 10 Jun 2009 17:09:40 +0000 (19:09 +0200)]
Add support for the Tundra TSI148 VME-bridge
From: Reinhard Arlt <reinhard.arlt@esd-electronics.com>
This patch adds support for the Tundra TSI148 VME-bridge. It's used on
the upcoming esd VME8349 board.
Signed-off-by: Reinhard Arlt <reinhard.arlt@esd-electronics.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Wolfgang Denk [Sat, 18 Jul 2009 23:15:52 +0000 (01:15 +0200)]
PATI board: fix compiler warnings
Fix these:
pati.c: In function 'checkboard':
pati.c:358: warning: pointer targets in passing argument 2 of 'getenv_r' differ in signedness
../common/flash.c: In function 'write_word':
../common/flash.c:824: warning: dereferencing type-punned pointer will break strict-aliasing rules
cmd_pati.c: In function 'do_pati':
cmd_pati.c:279: warning: 'value' may be used uninitialized in this function
Signed-off-by: Wolfgang Denk <wd@denx.de>
Jean-Christophe PLAGNIOL-VILLARD [Sat, 16 May 2009 10:14:56 +0000 (12:14 +0200)]
mpl: printing current stdio devices cleanup
Currently the mpl boards duplicate the code to print the current
devices from common/console.c; use stdio_print_current_devices()
instead
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Edited commit message.
Signed-off-by: Wolfgang Denk <wd@denx.de>
Jean-Christophe PLAGNIOL-VILLARD [Sat, 16 May 2009 10:14:55 +0000 (12:14 +0200)]
console: unify printing current devices
Create stdio_print_current_devices() for this purpose
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Wolfgang Denk [Sat, 18 Jul 2009 22:38:23 +0000 (00:38 +0200)]
Merge branch 'master' of git://git.denx.de/u-boot-nand-flash
Wolfgang Denk [Sat, 18 Jul 2009 21:18:14 +0000 (23:18 +0200)]
cmd_flash.c: fix warning: unused variable 'addr_first'/'addr_last'
Signed-off-by: Wolfgang Denk <wd@denx.de>
Tom Rix [Tue, 30 Jun 2009 20:04:13 +0000 (15:04 -0500)]
OMAP3 Fix compiler warning for v7_flush_dcache_all
On build of omap3 targets in MAKEALL, the *.ERR files have
cpu.c: In function 'cleanup_before_linux':
cpu.c:64: warning: implicit declaration of function 'v7_flush_dcache_all'
cpu.c:64: warning: implicit declaration of function 'get_device_type
The functions v7_flush_dcache_all and get_device_type are declared
in include/asm-arm/arch-omap3/sys_proto.h, so use this file to
declare the functions.
Signed-off-by: Tom Rix <Tom.Rix@windriver.com>
Wolfgang Denk [Sat, 18 Jul 2009 20:09:38 +0000 (22:09 +0200)]
ARM: make split_by_variant.sh output more useful
The board/armltd/integrator/split_by_variant.sh script used to print
"Configuring for integrator*p board..." no matter which board name
was being compiled. This made it difficult to match MAKEALL output to
board names. This patch fixes this.
Signed-off-by: Wolfgang Denk <wd@denx.de>
Wolfgang Denk [Sat, 18 Jul 2009 19:52:24 +0000 (21:52 +0200)]
NAND: Part 2: Fix warning Please define CONFIG_SYS_64BIT_VSPRINTF...
Commit
8d2effea added a warning for configurations that use NAND
without defining the (then necessary) CONFIG_SYS_64BIT_VSPRINTF but
failed to fix the affected boards.
This patch covers the non-PPC boards that were missed in the previous
patch (commit
170c1972).
Signed-off-by: Wolfgang Denk <wd@denx.de>
Wolfgang Denk [Sat, 18 Jul 2009 18:46:38 +0000 (20:46 +0200)]
at91cap9adk: fix #ifdef/#endif pairing
The #ifdef/#endif pairing in this file was obviously messed up.
Signed-off-by: Wolfgang Denk <wd@denx.de>
Wolfgang Denk [Sat, 18 Jul 2009 16:00:25 +0000 (18:00 +0200)]
pcm030: fix out-of-tree building
Commit
c9969947, which added support for the pcm030 board
(aka phyCORE-MPC5200B-tiny), broke out-of-tree building.
Signed-off-by: Wolfgang Denk <wd@denx.de>
Wolfgang Denk [Sat, 18 Jul 2009 14:36:11 +0000 (16:36 +0200)]
MPC837XERDB: fix warning: "CONFIG_SYS_MONITOR_LEN" redefined
Signed-off-by: Wolfgang Denk <wd@denx.de>
Wolfgang Denk [Sat, 18 Jul 2009 14:13:18 +0000 (16:13 +0200)]
8xxx: fix warning: implicit declaration of function 'uec_standard_init'
Commit
8e55258f created function uec_standard_init() to initialize
all UEC interfaces for 83xx and 85xx but failed to provide a
prototype for it.
Signed-off-by: Wolfgang Denk <wd@denx.de>
Wolfgang Denk [Sat, 18 Jul 2009 13:46:02 +0000 (15:46 +0200)]
MIP405T: fix compile problem
The "stdio/device: rework function naming convention" patch
(commit
52cb4d4f) broke the MIP405T board; this patch fixes it.
Signed-off-by: Wolfgang Denk <wd@denx.de>
Wolfgang Denk [Sat, 18 Jul 2009 13:32:10 +0000 (15:32 +0200)]
NAND: Fix warning Please define CONFIG_SYS_64BIT_VSPRINTF...
Commit
8d2effea added a warning for configurations that use NAND
without defining the (then necessary) CONFIG_SYS_64BIT_VSPRINTF but
failed to fix the affected boards.
Signed-off-by: Wolfgang Denk <wd@denx.de>
Wolfgang Denk [Sat, 18 Jul 2009 13:05:44 +0000 (15:05 +0200)]
CPCI750: fix compile problem
Commit
bc0d3296 removed ppc_error_no.h from Marvell boards
but forgot to update board/esd/cpci750/mv_eth.h
Signed-off-by: Wolfgang Denk <wd@denx.de>
Wolfgang Denk [Sat, 18 Jul 2009 12:59:40 +0000 (14:59 +0200)]
Merge branch 'master' of /home/wd/git/u-boot/custodians
Wolfgang Denk [Sat, 18 Jul 2009 12:59:05 +0000 (14:59 +0200)]
Merge branch 'master' of git://git.denx.de/u-boot-i2c
Alessandro Rubini [Fri, 17 Jul 2009 12:42:11 +0000 (14:42 +0200)]
cmd_i2c: bugfix: add missing brace
The sub-command parser missed a brace, so "return 0;" is always
taken and no error message is diplayed if you say "i2c scan"
instead of "i2c probe", for example.
Proper brace is added. Also, a misleading and unneeded else
is removed.
Signed-off-by: Alessandro Rubini <rubini@gnudd.com.it>
Jean-Christophe PLAGNIOL-VILLARD [Sat, 16 May 2009 10:14:54 +0000 (12:14 +0200)]
stdio/device: rework function naming convention
So far the console API uses the following naming convention:
======Extract======
typedef struct device_t;
int device_register (device_t * dev);
int devices_init (void);
int device_deregister(char *devname);
struct list_head* device_get_list(void);
device_t* device_get_by_name(char* name);
device_t* device_clone(device_t *dev);
=======
which is too generic and confusing.
Instead of using device_XX and device_t we change this
into stdio_XX and stdio_dev
This will also allow to add later a generic device mechanism in order
to have support for multiple devices and driver instances.
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Edited commit message.
Signed-off-by: Wolfgang Denk <wd@denx.de>
Peter Tyser [Wed, 15 Jul 2009 05:01:08 +0000 (00:01 -0500)]
ppc: Fix compile error for boards with CONFIG_DDR_ECC
A bug was introduced by commit
e94e460c6e8741f42dab6d8dd4b596ba5d9d79ae
which affected non-MPC83xx/85xx/86xx ppc boards which had CONFIG_DDR_ECC
defined and resulted in errors such as:
Configuring for canyonlands board...
fsl_dma.c:50:2: error: #error "Freescale DMA engine not supported on your
processor"
make[1]: *** No rule to make target `.depend', needed by `libdma.a'. Stop.
Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
Prafulla Wadaskar [Thu, 16 Jul 2009 15:27:59 +0000 (20:57 +0530)]
include/config_cmd_default.h cleanup
arranged configurations in alphabetical order
CONFIG_CMD_FLASH moved under ifndef CONFIG_SYS_NO_FLASH
Signed-off-by: Prafulla Wadaskar <prafulla@marvell.com>
Wolfgang Denk [Fri, 17 Jul 2009 21:05:41 +0000 (23:05 +0200)]
Merge branch 'master' of git://git.denx.de/u-boot-video
Wolfgang Denk [Fri, 17 Jul 2009 21:04:07 +0000 (23:04 +0200)]
Merge branch 'master' of git://git.denx.de/u-boot-microblaze
Mike Frysinger [Mon, 15 Jun 2009 01:35:22 +0000 (21:35 -0400)]
sata: namespace curr_device variable
The curr_device variable really should be namespaced with a "sata_" prefix
since it is only used by the sata code. It also avoids random conflicts
with other pieces of code (like cmd_mmc):
common/libcommon.a(cmd_sata.o):(.data.curr_device+0x0):
multiple definition of `curr_device'
common/libcommon.a(cmd_mmc.o):(.data.curr_device+0x0): first defined here
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Mike Frysinger [Mon, 15 Jun 2009 01:35:21 +0000 (21:35 -0400)]
cmd_mmc: make curr_device static
The curr_device variable isn't used outside of cmd_mmc, so mark it static
to avoid conflicts with other pieces of code (like sata which also exports
a curr_device). Otherwise we end up with stuff like:
common/libcommon.a(cmd_sata.o):(.data.curr_device+0x0):
multiple definition of `curr_device'
common/libcommon.a(cmd_mmc.o):(.data.curr_device+0x0): first defined here
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Mike Frysinger [Mon, 15 Jun 2009 01:35:16 +0000 (21:35 -0400)]
envcrc: add missing dependencies on env storage
When the envcrc building was made conditional, it missed a bunch of env
storage types, so add all currently supported types.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Scott Wood [Fri, 17 Jul 2009 00:08:04 +0000 (19:08 -0500)]
Remove legacy NAND and disk on chip references from boards.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Shinya Kuribayashi [Sat, 20 Jun 2009 10:10:14 +0000 (19:10 +0900)]
config.mk: Remove $(PCI_CLOCK) reference
The following commit introduced $(PCI_CLOCK) reference so that
we could tweak `PCI_66M' definition via an environment variable.
> commit
f046ccd15c8bc9613bfd72916b761a127d36e5c6
> Author: Eran Liberty <liberty@freescale.com>
> Date: Thu Jul 28 10:08:46 2005 -0500
>
> * Patch by Eran Liberty
> Add support for the Freescale MPC8349ADS board.
But I suggest a removal of it for the following reasons:
* In 2006, MPC8349ADS was merged into MPC8349EMDS port,
and it seems that MPC8349EMDS port is PCI_66M free.
* OTOH, PCI_66M is used by MPC832XEMDS an MPC8360EMDS ports,
but they don't need $(PCI_CLOCK) environment variable at all.
PCI_66M is automatically configured via $(BOARD)_config names
with the help of $(findstring _66_,$@).
* Unfortunately $(PCI_CLOCK) has been undocumented anywhere,
so only a few people know the existence of it these days.
* Keep config.mk independent from $(BOARD) as much as possible.
Signed-off-by: Shinya Kuribayashi <skuribay@pobox.com>
Acked-by: Kim Phillips <kim.phillips@freescale.com>
Jean-Christophe PLAGNIOL-VILLARD [Sat, 23 May 2009 19:42:36 +0000 (21:42 +0200)]
fix: missing autoconfig.mk from general Makefile
At the first run of make we generate the autoconf.mk and
autoconf.mk.dep if not already the case and we currently include only
to .dep
In order to use these autogenerated values we need to include it also
even if it's included in config.mk but it's done before their
generation
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Matthias Weisser [Thu, 9 Jul 2009 14:07:30 +0000 (16:07 +0200)]
Added support for splash screen positioning
This patch adds support splash image positioning by adding an
additional variable "splashpos" to the environment. Please see
README for details.
Signed-off-by: Matthias Weisser <matthias.weisser@graf-syteco.de>
Acked-by: Matthias Fuchs <matthias.fuchs@esd.eu>
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Anatolij Gustschin [Tue, 7 Jul 2009 11:11:36 +0000 (13:11 +0200)]
video: mb862xx: replace printf with puts
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Anatolij Gustschin [Tue, 7 Jul 2009 11:27:07 +0000 (13:27 +0200)]
video: mb862xx: use macros instead of magic numbers
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Anatolij Gustschin [Tue, 7 Jul 2009 11:24:08 +0000 (13:24 +0200)]
video: mb862xx: fix coding style and remove dead code
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Michal Simek [Tue, 30 Jun 2009 10:03:50 +0000 (12:03 +0200)]
microblaze: Remove ignored return type for __arch__swab16 function
This change remove compilation warnings.
Signed-off-by: Michal Simek <monstr@monstr.eu>
Michal Simek [Tue, 30 Jun 2009 10:02:45 +0000 (12:02 +0200)]
microblaze: Removed unused variables
Signed-off-by: Michal Simek <monstr@monstr.eu>
Scott Wood [Wed, 1 Apr 2009 20:02:13 +0000 (15:02 -0500)]
Remove legacy NAND and disk on chip code.
Legacy NAND had been scheduled for removal. Any boards that use this
were already not building in the previous release due to an #error.
The disk on chip code in common/cmd_doc.c relies on legacy NAND,
and it has also been removed. There is newer disk on chip code
in drivers/mtd/nand; someone with access to hardware and sufficient
time and motivation can try to get that working, but for now disk
on chip is not supported.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Stefan Roese [Thu, 4 Jun 2009 14:40:36 +0000 (16:40 +0200)]
nand: Change NAND_MAX_OOBSIZE to 218 as needed for some 4k page devices
This is needed for the MPC512x NAND driver (fsl_nfc_nand.c) which already
defines such a 4k plus 218 bytes ECC layout.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Scott Wood <scottwood@freescale.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
Stefan Roese [Thu, 16 Jul 2009 13:13:04 +0000 (15:13 +0200)]
nand: ndfc: Remove unnecessary #ifdef's
Now that the 4xx NAND driver ndfc is moved to the common NAND driver
directory we don't need this #ifdef's anymore.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Scott Wood <scottwood@freescale.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
Stefan Roese [Thu, 16 Jul 2009 13:12:48 +0000 (15:12 +0200)]
nand/ppc4xx: Move PPC4xx NAND driver to common NAND driver directory
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Scott Wood <scottwood@freescale.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
Valeriy Glushkov [Tue, 14 Jul 2009 10:51:10 +0000 (13:51 +0300)]
nand: fixed failed reads on corrected ECC errors in nand_util.c
Signed-off-by: Valeriy Glushkov <gvv@lstec.com>
Signed-off-by: Paulraj, Sandeep <s-paulraj@ti.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
David Brownell [Mon, 13 Jul 2009 23:29:04 +0000 (16:29 -0700)]
Typo fix: use CONFIG_SOC_DM644X, not CONFIG_SOC_DM646.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Scott Wood <scottwood@freescale.com>
Kyungmin Park [Sat, 11 Jul 2009 07:49:55 +0000 (16:49 +0900)]
MTD: OneNAND: Increase the environment size to 4KiB
Also use mtd operation instead of onenand functions
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
Anton Vorontsov [Tue, 9 Jun 2009 20:25:38 +0000 (00:25 +0400)]
mpc83xx: MPC837xEMDS: Use hwconfig instead of pci_external_arbiter variable
Since we have simple hwconfig interface now, we don't need
pci_external_arbiter variable any longer.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Acked-by: Kim Phillips <kim.phillips@freescale.com>
Anton Vorontsov [Tue, 9 Jun 2009 20:25:36 +0000 (00:25 +0400)]
mpc83xx: MPC8315ERDB: Use hwconfig for board type selection
This patch simply converts the board to the hwconfig infrastructure.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Acked-by: Kim Phillips <kim.phillips@freescale.com>
Anton Vorontsov [Tue, 9 Jun 2009 20:25:31 +0000 (00:25 +0400)]
mpc83xx: MPC837XEMDS: Fixup eSDHC nodes in device tree
fdt_fixup_esdhc() will either disable or enable eSDHC nodes, and
also will fixup clock-frequency property.
Plus, since DR USB and eSDHC are mutually exclusive, we should
only configure the eSDHC if asked through hwconfig.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Acked-by: Kim Phillips <kim.phillips@freescale.com>
Anton Vorontsov [Tue, 9 Jun 2009 20:25:30 +0000 (00:25 +0400)]
mpc83xx: MPC837XERDB: Add support for FSL eSDHC
This patch adds support for eSDHC on MPC837XERDB boards. The WP
switch doesn't seem to work on RDB boards though, the WP pin is
always asserted (can see the pin state when it's in GPIO mode).
FSL DR USB and FSL eSDHC are mutually exclusive because of pins
multiplexing, so user should specify 'esdhc' or 'dr_usb' options
in the hwconfig environment variable to choose between the
devices.
p.s.
Now we're very close to a monitor len limit (196 bytes left using
gcc-4.2.0), so also increase the monitor len by one sector (64 KB).
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Acked-by: Kim Phillips <kim.phillips@freescale.com>
Anton Vorontsov [Tue, 9 Jun 2009 20:25:29 +0000 (00:25 +0400)]
fsl_esdhc: Add device tree fixups
This patch implements fdt_fixup_esdhc() function that is used to fixup
the device tree.
The function adds status = "disabled" propery if esdhc pins muxed away,
otherwise it fixups clock-frequency for esdhc nodes.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Acked-by: Kim Phillips <kim.phillips@freescale.com>
Anton Vorontsov [Tue, 9 Jun 2009 20:25:27 +0000 (00:25 +0400)]
Add simple hwconfig infrastructure
This patch implements simple hwconfig infrastructure: an
interface for software knobs to control a hardware.
This is very simple implementation, i.e. it is implemented
via `hwconfig' environment variable. Later we could write
some "hwconfig <enable|disable|list>" commands, ncurses
interface for Award BIOS-like interface, and frame-buffer
interface for AMI GUI[1] BIOS-like interface with mouse
support[2].
Current implementation details/limitations:
1. Doesn't support options dependencies and mutual exclusion.
We can implement this by integrating apt-get[3] into the
u-boot. But I didn't bother yet.
2. Since we don't implement hwconfig command, i.e. we're working
with the environement directly, there is no way to tell that
toggling a particular option will need a reboot to take
an effect. So, for now it's advised to always reboot the
target after modifying hwconfig variable.
3. We support hwconfig options with arguments. For example,
set hwconfig dr_usb:mode=peripheral,phy_type=ulpi
That means:
- dr_usb - enable Dual-Role USB controller;
- dr_usb:mode=peripheral - USB in Function mode;
- dr_usb:phy_type=ulpi - USB should work with ULPI PHYs;
The purpose of this simple implementation is to define some
internal API and then we can continue improving user experience
by adding more mature interface, like hwconfig command with
bells and whistles. Or not adding, if we feel that current
interface fits its needs.
[1] http://en.wikipedia.org/wiki/American_Megatrends
[2] Regarding ncurses and GUI with mouse support -- I'm just
kidding.
[3] The comment regarding apt-get is also a joke, meaning that
dependency tracking could be non-trivial. For example, for
enabling HW feature X we may need to disable Y, and turn Z
into reduced mode (like RMII-only interface for ethernet,
no MII).
It's quite trivial to implement simple cases though.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Acked-by: Kim Phillips <kim.phillips@freescale.com>
Wolfgang Denk [Thu, 16 Jul 2009 20:13:54 +0000 (22:13 +0200)]
Merge branch 'master' of git://git.denx.de/u-boot-cfi-flash
Wolfgang Denk [Thu, 16 Jul 2009 20:13:45 +0000 (22:13 +0200)]
Merge branch 'master' of git://git.denx.de/u-boot-mpc83xx
Wolfgang Denk [Thu, 16 Jul 2009 19:53:15 +0000 (21:53 +0200)]
Merge branch 'asm-generic' of git://git.denx.de/u-boot-microblaze
Jerry Van Baren [Thu, 16 Jul 2009 00:42:59 +0000 (20:42 -0400)]
Improve U-Boot Porting Guide in the README
Update for...
* BDI2000 -> BDI3000 (BDI2000 is obsolete).
* Add a line to read the doc/README.* files
* Fix coding standard violations
Signed-off-by: Gerald Van Baren <vanbaren@cideas.com>
Kim Phillips [Tue, 14 Jul 2009 21:00:24 +0000 (16:00 -0500)]
mtd: cfi - if defined, use MAX_FLASH_BANKS_DETECT for static declarations
a.k.a cfi_mtd.c does as cfi_flash.c does. This also prevents
the TQM834x build from doing a:
cfi_mtd.c:36: error: variably modified 'cfi_mtd_info' at file scope
cfi_mtd.c:37: error: variably modified 'cfi_mtd_names' at file scope
using gcc 4.4.
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Kim Phillips [Tue, 7 Jul 2009 23:04:21 +0000 (18:04 -0500)]
mpc83xx: increase MONITOR_LEN to offset growing pains
Saving the environment leads to overwriting u-boot itself,
bricking boards. Increase u-boot's image size so the environment
base address doesn't end up overlapping u-boot text.
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Valeriy Glushkov [Tue, 30 Jun 2009 12:48:41 +0000 (15:48 +0300)]
usb: mpx8349itx: added support of loading images from USB storage (MPH/DR)
Signed-off-by: Valeriy Glushkov <gvv@lstec.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Valeriy Glushkov [Tue, 30 Jun 2009 12:48:40 +0000 (15:48 +0300)]
usb: mpc834x: added support of the MPH USB controller in addition to the DR one
Signed-off-by: Valeriy Glushkov <gvv@lstec.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Kim Phillips [Mon, 15 Jun 2009 16:51:47 +0000 (11:51 -0500)]
mpc83xx: set 64BIT_VSPRINTF for boards using nand_util
When enabling NAND support for a board, one must also define
CONFIG_SYS_64BIT_VSPRINTF because this is needed in nand_util.c
for correct output.
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Cc: Dave Liu <daveliu@freescale.com>
Cc: Ron Madrid <ron_madrid@sbcglobal.net>
Cc: Anton Vorontsov <avorontsov@ru.mvista.com>
Wolfgang Denk [Sun, 14 Jun 2009 18:58:53 +0000 (20:58 +0200)]
mpc5121ads: add JFFS2 and MTDPARTS support; adjust flash map
Signed-off-by: Wolfgang Denk <wd@denx.de>
Wolfgang Denk [Sun, 14 Jun 2009 18:58:52 +0000 (20:58 +0200)]
aria: add JFFS2 and MTDPARTS support; adjust flash map
Signed-off-by: Wolfgang Denk <wd@denx.de>
Wolfgang Denk [Sun, 14 Jun 2009 18:58:51 +0000 (20:58 +0200)]
aria: enable NAND flash support
Signed-off-by: Wolfgang Denk <wd@denx.de>
Wolfgang Denk [Sun, 14 Jun 2009 18:58:50 +0000 (20:58 +0200)]
MPC512x: fix typo in comment listing the NAND driver name
Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Stefan Roese <sr@denx.de>
Cc: Reinhard Arlt <reinhard.arlt@esd-electronics.com>
Wolfgang Denk [Sun, 14 Jun 2009 18:58:49 +0000 (20:58 +0200)]
mecp5123: cleanup - remove dead code
Remove dead code that was obviously a left-over from copy & paste.
Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Stefan Roese <sr@denx.de>
Cc: Reinhard Arlt <reinhard.arlt@esd-electronics.com>
Wolfgang Denk [Sun, 14 Jun 2009 18:58:48 +0000 (20:58 +0200)]
aria: adjust memory controller initialization
Needed for Rev. 2 silicon at 400 MHz
Signed-off-by: Wolfgang Denk <wd@denx.de>
Wolfgang Denk [Sun, 14 Jun 2009 18:58:47 +0000 (20:58 +0200)]
MPC512x: factor out common code
Now that we have 3 boards for the MPC512x it turns out that they all
use the very same fixed_sdram() code.
This patch factors out this common code into cpu/mpc512x/fixed_sdram.c
and adds a new header file, include/asm-ppc/mpc512x.h, with some
macros, inline functions and prototype definitions specific to MPC512x
systems.
Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Stefan Roese <sr@denx.de>
Cc: Reinhard Arlt <reinhard.arlt@esd-electronics.com>
Wolfgang Denk [Sun, 14 Jun 2009 18:58:46 +0000 (20:58 +0200)]
mecp5123: fix build error
The mecp5123 board did not compile because the MSCAN Clock Control
Registers were missing; these got added, but as an array instead
of 4 individual registers. Adapt the code so it builds.
Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Stefan Roese <sr@denx.de>
Cc: Reinhard Arlt <reinhard.arlt@esd-electronics.com>
Wolfgang Denk [Sun, 14 Jun 2009 18:58:45 +0000 (20:58 +0200)]
MPC512x: Add MSCAN1...4 Clock Control Registers
Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Stefan Roese <sr@denx.de>
Cc: Reinhard Arlt <reinhard.arlt@esd-electronics.com>
Wolfgang Denk [Sun, 14 Jun 2009 18:58:44 +0000 (20:58 +0200)]
MPC512x: enabling NAND support requires CONFIG_SYS_64BIT_VSPRINTF
When enabling NAND support for a board, one must also define
CONFIG_SYS_64BIT_VSPRINTF because this is needed in nand_util.c
for correct output.
Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Stefan Roese <sr@denx.de>
Cc: Reinhard Arlt <reinhard.arlt@esd-electronics.com>
Wolfgang Denk [Mon, 13 Jul 2009 22:00:04 +0000 (00:00 +0200)]
Merge branch 'master' of /home/wd/git/u-boot/master
Wolfgang Denk [Mon, 13 Jul 2009 21:45:10 +0000 (23:45 +0200)]
Merge branch 'master' of /home/wd/git/u-boot/custodians
Wolfgang Denk [Mon, 13 Jul 2009 21:45:02 +0000 (23:45 +0200)]
Merge branch 'master' of git://git.denx.de/u-boot-arm
Wolfgang Denk [Mon, 13 Jul 2009 21:38:29 +0000 (23:38 +0200)]
Merge branch 'master' of /home/wd/git/u-boot/custodians
Wolfgang Denk [Mon, 13 Jul 2009 21:38:27 +0000 (23:38 +0200)]
Merge branch 'master' of git://git.denx.de/u-boot-cfi-flash
Wolfgang Denk [Mon, 13 Jul 2009 21:37:59 +0000 (23:37 +0200)]
Merge branch 'master' of /home/wd/git/u-boot/custodians
Wolfgang Denk [Mon, 13 Jul 2009 21:37:55 +0000 (23:37 +0200)]
Merge branch 'master' of git://git.denx.de/u-boot-sh
Wolfgang Denk [Mon, 13 Jul 2009 21:34:33 +0000 (23:34 +0200)]
Merge branch 'master' of /home/wd/git/u-boot/custodians
Wolfgang Denk [Mon, 13 Jul 2009 21:34:30 +0000 (23:34 +0200)]
Merge branch 'master' of git://git.denx.de/u-boot-ppc4xx
Wolfgang Denk [Mon, 13 Jul 2009 21:33:20 +0000 (23:33 +0200)]
Merge branch 'master' of /home/wd/git/u-boot/custodians
Wolfgang Denk [Mon, 13 Jul 2009 21:33:16 +0000 (23:33 +0200)]
Merge branch 'master' of git://git.denx.de/u-boot-blackfin
Wolfgang Denk [Mon, 13 Jul 2009 21:32:08 +0000 (23:32 +0200)]
Merge branch 'master' of /home/wd/git/u-boot/custodians
Wolfgang Denk [Mon, 13 Jul 2009 21:32:01 +0000 (23:32 +0200)]
Merge branch 'master' of git://git.denx.de/u-boot-usb
Wolfgang Denk [Mon, 13 Jul 2009 21:28:55 +0000 (23:28 +0200)]
Merge branch 'master' of /home/wd/git/u-boot/custodians
Wolfgang Denk [Mon, 13 Jul 2009 21:28:37 +0000 (23:28 +0200)]
Merge branch 'master' of git://git.denx.de/u-boot-ubi
Po-Yu Chuang [Fri, 10 Jul 2009 10:03:57 +0000 (18:03 +0800)]
issue write command to base for JEDEC flash
For JEDEC flash, we should issue word programming command relative to
base address rather than sector base address. Original source makes
SST Flash fails to program sectors which are not on the 0x10000 boundaries.
e.g.
SST39LF040 uses addr1=0x5555 and addr2=0x2AAA, however, each sector
is 0x1000 bytes.
Thus, if we issue command to "sector base (0x41000) + offset(0x5555)",
it sends to 0x46555 and the chip fails to recognize that address.
This patch is tested with SST39LF040.
Signed-off-by: Po-Yu Chuang <ratbert@faraday-tech.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Jean-Christophe PLAGNIOL-VILLARD [Sat, 2 May 2009 09:53:50 +0000 (11:53 +0200)]
versatile: update config and merge to cfi flash driver
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Peter Pearse <peter.pearse@arm.com>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Jean-Christophe PLAGNIOL-VILLARD [Sat, 2 May 2009 09:53:49 +0000 (11:53 +0200)]
versatile: specify the board type on the prompt
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Peter Pearse <peter.pearse@arm.com>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Sedji Gaouaou [Thu, 25 Jun 2009 15:04:15 +0000 (17:04 +0200)]
at91: Introduction of at91sam9g10 SOC.
AT91sam9g10 is an ARM 926ej-s SOC. It is an evolution of the at91sam9261 with a
faster clock speed: 266/133MHz.
Signed-off-by: Sedji Gaouaou <sedji.gaouaou@atmel.com>
Sedji Gaouaou [Thu, 9 Jul 2009 08:16:29 +0000 (10:16 +0200)]
at91: Introduction of at91sam9g45 SOC.
AT91sam9g45 series is an ARM 926ej-s SOC family clocked at 400/133MHz.
It embeds USB high speed host and device, LCD, DDR2 RAM, and a full set of
peripherals.
The first board that embeds at91sam9g45 chip is the AT91SAM9G45-EKES.
On the board you can find 2 USART, USB high speed,
a 480*272 LG lcd, ethernet, gpio/joystick/buttons.
Signed-off-by: Sedji Gaouaou <sedji.gaouaou@atmel.com>
Daniel Mack [Tue, 23 Jun 2009 15:30:05 +0000 (17:30 +0200)]
pxa: fix CKEN_B register bits
The current defition for CKEN_B register bits is nonsense. Adding 32 to
the shifted value is equal to '| (1 << 5)', and this bit is marked
'reserved' in the PXA docs.
Signed-off-by: Daniel Mack <daniel@caiaq.de>
Daniel Mack [Tue, 23 Jun 2009 15:30:04 +0000 (17:30 +0200)]
pxa: add clock for system bus 2 arbiter
This clock is needed for systems using the USB2 device unit or the 2d
graphics accelerator.
Signed-off-by: Daniel Mack <daniel@caiaq.de>
Grazvydas Ignotas [Tue, 7 Jul 2009 21:30:01 +0000 (00:30 +0300)]
OMAP3 pandora: Fix CKE1 MUX setting to allow self-refresh
Pandora is using both SDRC CSes. The MUX setting is needed
for the second CS clock signal to allow the 2 RAM parts to
be put in self-refresh correctly.
Based on similar patch for beagle and overo by
Jean Pihet and Steve Sakoman.
Grazvydas Ignotas [Tue, 7 Jul 2009 21:30:00 +0000 (00:30 +0300)]
OMAP3 pandora: setup pulls for various GPIOs
Set pullups or pulldowns for GPIOs which need them.
Disable them for others, which have external pulls.
Also make disabled pull setting consistent (some pins had
type set to "up" even if pull type selection was disabled).
Grazvydas Ignotas [Tue, 7 Jul 2009 21:29:59 +0000 (00:29 +0300)]
OMAP3 pandora: setup pin mux for pins used on rev3 boards
Setup pin mux for GPIO pins connected on rev3 or later
boards. Also change NUB2 IRQ pin. This should not affect
older boards because they don't have any nubs (analog
controllers) attached to them.
Grazvydas Ignotas [Tue, 7 Jul 2009 21:29:58 +0000 (00:29 +0300)]
OMAP3 pandora: pin mux cleanup
Remove configuration of not unused pins, effectively
leaving them in safe mode.
Prafulla Wadaskar [Mon, 6 Jul 2009 10:20:47 +0000 (15:50 +0530)]
arm: Kirkwood: bugfix: UART1 bar correction
Signed-off-by: Prafulla Wadaskar <prafulla@marvell.com>
Kumar Gala [Tue, 7 Jul 2009 20:48:58 +0000 (15:48 -0500)]
usb: Fix compiler warning with gcc4.4
ehci-hcd.c: In function 'ehci_submit_root':
ehci-hcd.c:719: warning: value computed is not used
ehci-hcd.c:748: warning: value computed is not used
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Remy Bohmer <linux@bohmer.net>
Nobuhiro Iwamatsu [Wed, 8 Jul 2009 02:42:19 +0000 (11:42 +0900)]
sh: Update pci config for Renesas r7780mp board
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Nobuhiro Iwamatsu [Thu, 25 Jun 2009 07:31:26 +0000 (16:31 +0900)]
sh: Add support ESPT-GIGA borad
ESPT-Giga is SH7763-based reference board.
Board support is relatively sparse, presently supporting serial,
gigabit ethernet, USB host, and MTD.
More information (in Japanese) available at:
http://www.cente.jp/product/cente_hard/ESPT-Giga.html
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu.nobuhiro@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>