#include "ls2080a_common.h"
-#ifdef CONFIG_FSL_QSPI
-#ifdef CONFIG_TARGET_LS2081ARDB
-#define CONFIG_QIXIS_I2C_ACCESS
-#endif
-#endif
-
#define I2C_MUX_CH_VOL_MONITOR 0xa
#define I2C_VOL_MONITOR_ADDR 0x38
-#define CONFIG_VOL_MONITOR_IR36021_READ
-#define CONFIG_VOL_MONITOR_IR36021_SET
-#define CONFIG_VID_FLS_ENV "ls2080ardb_vdd_mv"
-#ifndef CONFIG_SPL_BUILD
-#define CONFIG_VID
-#endif
/* step the IR regulator in 5mV increments */
#define IR_VDD_STEP_DOWN 5
#define IR_VDD_STEP_UP 5
#define VDD_MV_MIN 819
#define VDD_MV_MAX 1212
-#ifndef __ASSEMBLY__
-unsigned long get_board_sys_clk(void);
-#endif
-
-#define CONFIG_SYS_CLK_FREQ get_board_sys_clk()
-#define COUNTER_FREQUENCY_REAL (CONFIG_SYS_CLK_FREQ/4)
+#define COUNTER_FREQUENCY_REAL (get_board_sys_clk()/4)
#define CONFIG_MEM_INIT_VALUE 0xdeadbeef
#define SPD_EEPROM_ADDRESS1 0x51
#define SPD_EEPROM_ADDRESS5 0x55
#define SPD_EEPROM_ADDRESS6 0x56 /* dummy address */
#define SPD_EEPROM_ADDRESS SPD_EEPROM_ADDRESS1
-#define CONFIG_SYS_SPD_BUS_NUM 0 /* SPD on I2C bus 0 */
-#define CONFIG_DIMM_SLOTS_PER_CTLR 2
-#define CONFIG_CHIP_SELECTS_PER_CTRL 4
-#ifdef CONFIG_SYS_FSL_HAS_DP_DDR
-#define CONFIG_DP_DDR_DIMM_SLOTS_PER_CTLR 1
-#endif
-
-/* SATA */
-#define CONFIG_SCSI_AHCI_PLAT
-
-#define CONFIG_SYS_SATA1 AHCI_BASE_ADDR1
-#define CONFIG_SYS_SATA2 AHCI_BASE_ADDR2
-
-#define CONFIG_SYS_SCSI_MAX_SCSI_ID 1
-#define CONFIG_SYS_SCSI_MAX_LUN 1
-#define CONFIG_SYS_SCSI_MAX_DEVICE (CONFIG_SYS_SCSI_MAX_SCSI_ID * \
- CONFIG_SYS_SCSI_MAX_LUN)
#if !defined(CONFIG_FSL_QSPI) || defined(CONFIG_TFABOOT)
#define CONFIG_SYS_IFC_CCR 0x01000000
#ifdef CONFIG_MTD_NOR_FLASH
-#define CONFIG_SYS_FLASH_QUIET_TEST
#define CONFIG_FLASH_SHOW_PROGRESS 45 /* count down from 45/5: 9..1 */
-#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* number of banks */
-#define CONFIG_SYS_MAX_FLASH_SECT 1024 /* sectors per device */
-#define CONFIG_SYS_FLASH_ERASE_TOUT 60000 /* Flash Erase Timeout (ms) */
-#define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (ms) */
-
-#define CONFIG_SYS_FLASH_EMPTY_INFO
#define CONFIG_SYS_FLASH_BANKS_LIST { CONFIG_SYS_FLASH_BASE,\
CONFIG_SYS_FLASH_BASE + 0x40000000}
#endif
#define CONFIG_SYS_NAND_FTIM3 0x0
#define CONFIG_SYS_NAND_BASE_LIST { CONFIG_SYS_NAND_BASE }
-#define CONFIG_SYS_MAX_NAND_DEVICE 1
#define CONFIG_MTD_NAND_VERIFY_WRITE
-#define CONFIG_FSL_QIXIS /* use common QIXIS code */
#define QIXIS_LBMAP_SWITCH 0x06
#define QIXIS_LBMAP_MASK 0x0f
#define QIXIS_LBMAP_SHIFT 0
#define CONFIG_SYS_CS0_FTIM2 CONFIG_SYS_NAND_FTIM2
#define CONFIG_SYS_CS0_FTIM3 CONFIG_SYS_NAND_FTIM3
-#define CONFIG_SPL_PAD_TO 0x80000
#define CONFIG_SYS_NAND_U_BOOT_SIZE (512 * 1024)
#else
#define CONFIG_SYS_CSPR0_EXT CONFIG_SYS_NOR0_CSPR_EXT
#define CONFIG_SYS_CS2_FTIM2 CONFIG_SYS_NAND_FTIM2
#define CONFIG_SYS_CS2_FTIM3 CONFIG_SYS_NAND_FTIM3
#endif
-
-/* Debug Server firmware */
-#define CONFIG_SYS_DEBUG_SERVER_FW_IN_NOR
-#define CONFIG_SYS_DEBUG_SERVER_FW_ADDR 0x580D00000ULL
#endif
#define CONFIG_SYS_LS_MC_BOOT_TIMEOUT_MS 5000
#ifdef CONFIG_TARGET_LS2081ARDB
-#define CONFIG_FSL_QIXIS /* use common QIXIS code */
#define QIXIS_QMAP_MASK 0x07
#define QIXIS_QMAP_SHIFT 5
#define QIXIS_LBMAP_DFLTBANK 0x00
#define I2C_MUX_CH_DEFAULT 0x8
/* SPI */
-#if defined(CONFIG_FSL_DSPI)
-#define CONFIG_SPI_FLASH_STMICRO
-#endif
/*
* RTC configuration
#define CONFIG_SYS_I2C_RTC_ADDR 0x68
#endif
-/* EEPROM */
-#define CONFIG_SYS_I2C_EEPROM_NXID
-#define CONFIG_SYS_EEPROM_BUS_NUM 0
-
-#define CONFIG_FSL_MEMAC
-
-#ifdef CONFIG_PCI
-#define CONFIG_PCI_SCAN_SHOW
-#endif
-
#define BOOT_TARGET_DEVICES(func) \
func(USB, usb, 0) \
func(MMC, mmc, 0) \
"ramdisk_size=0x2000000\0" \
"fdt_high=0xa0000000\0" \
"initrd_high=0xffffffffffffffff\0" \
- "fdt_addr=0x64f00000\0" \
"kernel_addr=0x581000000\0" \
"kernel_start=0x1000000\0" \
"kernelheader_start=0x800000\0" \
"ramdisk_size=0x2000000\0" \
"fdt_high=0xa0000000\0" \
"initrd_high=0xffffffffffffffff\0" \
- "fdt_addr=0x64f00000\0" \
"kernel_addr=0x581000000\0" \
"kernel_start=0x1000000\0" \
"kernelheader_start=0x600000\0" \
"run distro_bootcmd;run nor_bootcmd; " \
"env exists secureboot && esbc_halt;"
#else
-#undef CONFIG_BOOTCOMMAND
#ifdef CONFIG_QSPI_BOOT
/* Try to boot an on-QSPI kernel first, then do normal distro boot */
-#define CONFIG_BOOTCOMMAND \
- "sf probe 0:0; " \
- "sf read 0x806c0000 0x6c0000 0x40000; " \
- "env exists mcinitcmd && env exists secureboot "\
- "&& esbc_validate 0x806C0000; " \
- "sf read 0x80d00000 0xd00000 0x100000; " \
- "env exists mcinitcmd && " \
- "fsl_mc lazyapply dpl 0x80d00000; " \
- "run distro_bootcmd;run qspi_bootcmd; " \
- "env exists secureboot && esbc_halt;"
#elif defined(CONFIG_SD_BOOT)
/* Try to boot an on-SD kernel first, then do normal distro boot */
-#define CONFIG_BOOTCOMMAND \
- "env exists mcinitcmd && env exists secureboot "\
- "&& mmcinfo && mmc read $load_addr 0x3600 0x800 " \
- "&& esbc_validate $load_addr; " \
- "env exists mcinitcmd && run mcinitcmd " \
- "&& mmc read 0x88000000 0x6800 0x800 " \
- "&& fsl_mc lazyapply dpl 0x88000000; " \
- "run distro_bootcmd;run sd_bootcmd; " \
- "env exists secureboot && esbc_halt;"
#else
/* Try to boot an on-NOR kernel first, then do normal distro boot */
-#define CONFIG_BOOTCOMMAND \
- "env exists mcinitcmd && env exists secureboot "\
- "&& esbc_validate 0x5806C0000; env exists mcinitcmd "\
- "&& fsl_mc lazyapply dpl 0x580d00000;" \
- "run distro_bootcmd;run nor_bootcmd; " \
- "env exists secureboot && esbc_halt;"
#endif
#endif
#define AQ_PHY_ADDR3 0x02
#define AQ_PHY_ADDR4 0x03
#define AQR405_IRQ_MASK 0x36
-#define CONFIG_ETHPRIME "DPMAC1@xgmii"
#include <asm/fsl_secure_boot.h>
projects / platform / kernel / u-boot.git / blobdiff