+/* SPDX-License-Identifier: GPL-2.0+ */
/*
* Copyright (C) 2011 Simon Guinot <sguinot@lacie.com>
- *
- * SPDX-License-Identifier: GPL-2.0+
*/
#ifndef _CONFIG_LACIE_KW_H
#define CONFIG_SKIP_LOWLEVEL_INIT /* disable board lowlevel_init */
/*
- * Commands configuration
- */
-#ifndef CONFIG_NETSPACE_MINI_V2 /* No USB ports on Network Space v2 Mini */
-#endif
-
-/*
* Core clock definition
*/
#define CONFIG_SYS_TCLK 166000000 /* 166MHz */
/*
* SDRAM configuration
*/
-#define CONFIG_NR_DRAM_BANKS 1
/*
* Different SDRAM configuration and size for some of the boards derived
#include "mv-common.h"
/* Remove or override few declarations from mv-common.h */
-#undef CONFIG_RBTREE
-#undef CONFIG_ENV_SPI_MAX_HZ
#undef CONFIG_SYS_IDE_MAXBUS
#undef CONFIG_SYS_IDE_MAXDEVICE
-#define CONFIG_ENV_SPI_MAX_HZ 20000000 /* 20Mhz */
/*
* Enable platform initialisation via misc_init_r() function
*/
-#define CONFIG_MISC_INIT_R
/*
* Ethernet Driver configuration
*/
#ifdef CONFIG_CMD_NET
#define CONFIG_MVGBE_PORTS {1, 0} /* enable port 0 only */
-#define CONFIG_NETCONSOLE
#endif
/*
* SATA Driver configuration
*/
-#ifdef CONFIG_MVSATA_IDE
-#define CONFIG_SYS_ATA_IDE0_OFFSET MV_SATA_PORT0_OFFSET
+
+#ifdef CONFIG_SATA
+#define CONFIG_SYS_64BIT_LBA
+#define CONFIG_LBA48
#if defined(CONFIG_NETSPACE_MAX_V2) || defined(CONFIG_D2NET_V2) || \
defined(CONFIG_NET2BIG_V2)
-#define CONFIG_SYS_ATA_IDE1_OFFSET MV_SATA_PORT1_OFFSET
-#define CONFIG_SYS_IDE_MAXBUS 2
-#define CONFIG_SYS_IDE_MAXDEVICE 2
+#define CONFIG_SYS_SATA_MAX_DEVICE 2
#else
-#define CONFIG_SYS_IDE_MAXBUS 1
-#define CONFIG_SYS_IDE_MAXDEVICE 1
+#define CONFIG_SYS_SATA_MAX_DEVICE 1
#endif
-#endif /* CONFIG_MVSATA_IDE */
+#endif /* CONFIG_SATA */
/*
* Enable GPI0 support
/*
* Environment variables configurations
*/
-#define CONFIG_ENV_IS_IN_SPI_FLASH
-#define CONFIG_ENV_SECT_SIZE 0x10000 /* 64KB */
-#define CONFIG_ENV_SIZE 0x1000 /* 4KB */
-#define CONFIG_ENV_ADDR 0x70000
-#define CONFIG_ENV_OFFSET 0x70000 /* env starts here */
/*
* Default environment variables
*/
-#define CONFIG_BOOTARGS "console=ttyS0,115200"
-
#define CONFIG_BOOTCOMMAND \
"dhcp && run netconsole; " \
"if run usbload || run diskload; then bootm; fi"
"set stdin $stdin,nc; " \
"set stdout $stdout,nc; " \
"set stderr $stderr,nc;\0" \
- "diskload=ide reset && " \
- "ext2load ide 0:1 $loadaddr /boot/$bootfile\0" \
+ "diskload=sata init && " \
+ "ext2load sata 0:1 $loadaddr /boot/$bootfile\0" \
"usbload=usb start && " \
"fatload usb 0:1 $loadaddr /boot/$bootfile\0"