#define KM_I2C_DEBLOCK_SDA 21
/* High Level Configuration Options */
-#define CONFIG_SYS_BOOK3E_HV /* Category E.HV supported */
-#define CONFIG_FSL_CORENET /* Freescale CoreNet platform */
#define CONFIG_RESET_VECTOR_ADDRESS 0xebfffffc
-#define CONFIG_SYS_FSL_CPC /* Corenet Platform Cache */
#define CONFIG_SYS_NUM_CPC CONFIG_SYS_NUM_DDR_CTLRS
-#define CONFIG_PCIE1 /* PCIE controller 1 */
-#define CONFIG_SYS_PCI_64BIT /* enable 64-bit PCI resources */
/* Environment in parallel NOR-Flash */
#define CONFIG_ENV_TOTAL_SIZE 0x040000
#define ENV_DEL_ADDR 0xebf00000 /*direct for newenv*/
-#define CONFIG_SYS_CLK_FREQ 66666666
-
/*
* These can be toggled for performance analysis, otherwise use default.
*/
-#define CONFIG_SYS_CACHE_STASHING
-#define CONFIG_BACKSIDE_L2_CACHE
#define CONFIG_SYS_INIT_L2CSR0 L2CSR0_L2E
-#define CONFIG_BTB /* toggle branch predition */
-
-#define CONFIG_ENABLE_36BIT_PHYS
/* POST memory regions test */
#define CONFIG_POST CONFIG_SYS_POST_MEM_REGIONS
* Config the L3 Cache as L3 SRAM
*/
#define CONFIG_SYS_INIT_L3_ADDR 0xFFFC0000
-#define CONFIG_SYS_L3_SIZE 256 << 10
#define CONFIG_SYS_DCSRBAR 0xf0000000
#define CONFIG_SYS_DCSRBAR_PHYS 0xf00000000ull
#define CONFIG_VERY_BIG_RAM
#define CONFIG_SYS_DDR_SDRAM_BASE 0x00000000
#define CONFIG_SYS_SDRAM_BASE CONFIG_SYS_DDR_SDRAM_BASE
-#define CONFIG_DDR_CLK_FREQ 66666666
-
-#define CONFIG_DIMM_SLOTS_PER_CTLR 1
-#define CONFIG_CHIP_SELECTS_PER_CTRL (2 * CONFIG_DIMM_SLOTS_PER_CTLR)
-#define CONFIG_DDR_SPD
-
-#define CONFIG_SYS_SPD_BUS_NUM 0
#define SPD_EEPROM_ADDRESS 0x54
#define CONFIG_SYS_SDRAM_SIZE 4096 /* for fixed parameter use */
-#define CONFIG_SYS_LOAD_ADDR 0x2000000 /* default load address */
-
/******************************************************************************
* (PRAM usage)
* ... -------------------------------------------------------
* @CONFIG_KM_RESERVED_PRAM: reserved pram for special purpose
* @CONFIG_KM_PHRAM: address for /var
* @CONFIG_KM_PNVRAM: address for PNVRAM (for the application)
- * @CONFIG_KM_ROOTFSSIZE: address for rootfilesystem in RAM
*/
-/* size of rootfs in RAM */
-#define CONFIG_KM_ROOTFSSIZE 0x0
/* set the default PRAM value to at least PNVRAM + PHRAM when pram env variable
* is not valid yet, which is the case for when u-boot copies itself to RAM
*/
#define CONFIG_SYS_CS0_FTIM3 CONFIG_SYS_NOR_FTIM3
/* More NOR Flash params */
-#define CONFIG_SYS_FLASH_QUIET_TEST
-#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* number of banks */
-#define CONFIG_SYS_MAX_FLASH_SECT 512 /* sectors per device */
-
-#define CONFIG_SYS_FLASH_EMPTY_INFO
#define CONFIG_SYS_FLASH_BANKS_LIST {CONFIG_SYS_FLASH_BASE_PHYS}
/* NAND Flash on IFC CS1*/
-#define CONFIG_NAND_FSL_IFC
#define CONFIG_SYS_NAND_BASE 0xfa000000
#define CONFIG_SYS_NAND_BASE_PHYS (0xf00000000ull | CONFIG_SYS_NAND_BASE)
CSOR_NAND_TRHZ_40 | /**/ \
CSOR_NAND_BCTLD) /**/
-#define CONFIG_SYS_NAND_ONFI_DETECTION
-
/* ONFI NAND Flash mode0 Timing Params */
#define CONFIG_SYS_NAND_FTIM0 (FTIM0_NAND_TCCST(0x3) | \
FTIM0_NAND_TWP(0x8) | \
/* More NAND Flash Params */
#define CONFIG_SYS_NAND_BASE_LIST { CONFIG_SYS_NAND_BASE }
-#define CONFIG_SYS_MAX_NAND_DEVICE 1
/* QRIO on IFC CS2 */
#define CONFIG_SYS_QRIO_BASE 0xfb000000
#define CONFIG_SYS_CS2_FTIM2 SYS_QRIO_FTIM2
#define CONFIG_SYS_CS2_FTIM3 SYS_QRIO_FTIM3
-#define CONFIG_MISC_INIT_F
#define CONFIG_HWCONFIG
/* define to use L1 as initial stack */
-#define CONFIG_SYS_INIT_RAM_LOCK
#define CONFIG_SYS_INIT_RAM_ADDR 0xfdd00000 /* Initial L1 address */
#define CONFIG_SYS_INIT_RAM_ADDR_PHYS_HIGH 0xf
#define CONFIG_SYS_INIT_RAM_ADDR_PHYS_LOW 0xfe03c000
CONFIG_SYS_INIT_RAM_ADDR_PHYS_LOW)
#define CONFIG_SYS_INIT_RAM_SIZE 0x00004000
-#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - \
- GENERATED_GBL_DATA_SIZE)
-#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET
+#define CONFIG_SYS_INIT_SP_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
-#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE /* start of monitor */
#define CONFIG_SYS_MONITOR_LEN 0xc0000 /* 768k */
-#define CONFIG_SYS_MALLOC_LEN (4 * 1024 * 1024)
-
/*
* Serial Port - controlled on board with jumper J8
* open - index 2
* Retain non-DM serial port for debug purposes.
*/
#if !defined(CONFIG_DM_SERIAL)
-#define CONFIG_CONS_INDEX 1
#define CONFIG_SYS_NS16550_SERIAL
#define CONFIG_SYS_NS16550_REG_SIZE 1
#define CONFIG_SYS_NS16550_CLK (get_bus_freq(0) / 2)
#define CONFIG_SYS_DPAA_FMAN
#define CONFIG_SYS_DPAA_PME
-/* Default address of microcode for the Linux Fman driver */
-#define CONFIG_SYS_FMAN_FW_ADDR 0xE8020000
-#define CONFIG_SYS_QE_FW_ADDR 0xE8040000
-#define CONFIG_SYS_QE_FMAN_FW_LENGTH 0x10000
-#define CONFIG_SYS_FDT_PAD (0x3000 + CONFIG_SYS_QE_FMAN_FW_LENGTH)
-
/* Qman / Bman */
/* RGMII (FM1@DTESC5) is local managemant interface */
#define CONFIG_SYS_RGMII2_PHY_ADDR 0x11
-#define CONFIG_ETHPRIME "fm1-mac5"
/*
* Hardware Watchdog
* the maximum mapped by the Linux kernel during initialization.
*/
#define CONFIG_SYS_BOOTMAPSZ (64 << 20) /* Initial map for Linux*/
-#define CONFIG_SYS_BOOTM_LEN (64 << 20) /* Increase max gunzip size */
/*
* Environment Configuration
projects / platform / kernel / u-boot.git / blobdiff