#ifndef __CONFIG_H
#define __CONFIG_H
-#define CONFIG_NR_DRAM_BANKS 2 /* CS1 may or may not be populated */
-
-/*
- * 1MB into the SDRAM to allow for SPL's bss at the beginning of SDRAM
- * 64 bytes before this address should be set aside for u-boot.img's
- * header. That is 0x800FFFC0--0x80100000 should not be used for any
- * other needs.
- */
-
-#define CONFIG_SYS_SPL_MALLOC_START 0x80208000
-#define CONFIG_SYS_SPL_MALLOC_SIZE 0x100000
-
#include <configs/ti_omap3_common.h>
-#undef CONFIG_SDRC /* Disable SDRC since we have EMIF4 */
-
-#define CONFIG_MISC_INIT_R
-#define CONFIG_REVISION_TAG
-
-/* Hardware drivers */
-
-/* allow to overwrite serial and ethaddr */
-#define CONFIG_ENV_OVERWRITE
-
-/*
- * USB configuration
- * Enable CONFIG_USB_MUSB_HOST for Host functionalities MSC, keyboard
- * Enable CONFIG_USB_MUSB_GADGET for Device functionalities.
- */
-
-#ifdef CONFIG_USB_MUSB_AM35X
-
-#ifdef CONFIG_USB_MUSB_HOST
-
-#ifdef CONFIG_USB_KEYBOARD
-#define CONFIG_PREBOOT "usb start"
-#endif /* CONFIG_USB_KEYBOARD */
-
-#endif /* CONFIG_USB_MUSB_HOST */
-
-#endif /* CONFIG_USB_MUSB_AM35X */
-
-/* I2C */
/* Ethernet */
-#define CONFIG_DRIVER_TI_EMAC
-#define CONFIG_DRIVER_TI_EMAC_USE_RMII
-#define CONFIG_MII
-#define CONFIG_BOOTP_DEFAULT
-#define CONFIG_BOOTP_DNS2
-#define CONFIG_BOOTP_SEND_HOSTNAME
#define CONFIG_NET_RETRY_COUNT 10
/* Board NAND Info. */
-#ifdef CONFIG_NAND
-#define CONFIG_SYS_NAND_ADDR NAND_BASE /* physical address */
- /* to access nand */
-#define CONFIG_SYS_NAND_5_ADDR_CYCLE
-#define CONFIG_SYS_NAND_PAGE_COUNT 64
-#define CONFIG_SYS_NAND_PAGE_SIZE 2048
-#define CONFIG_SYS_NAND_OOBSIZE 64
-#define CONFIG_SYS_NAND_BLOCK_SIZE (128 * 1024)
-#define CONFIG_SYS_NAND_BAD_BLOCK_POS NAND_LARGE_BADBLOCK_POS
+#ifdef CONFIG_MTD_RAW_NAND
#define CONFIG_SYS_NAND_ECCPOS { 2, 3, 4, 5, 6, 7, 8, 9, 10, \
11, 12, 13, 14, 16, 17, 18, 19, 20, \
21, 22, 23, 24, 25, 26, 27, 28, 30, \
#define CONFIG_SYS_NAND_ECCSIZE 512
#define CONFIG_SYS_NAND_ECCBYTES 13
-#define CONFIG_NAND_OMAP_ECCSCHEME OMAP_ECC_BCH8_CODE_HW_DETECTION_SW
#define CONFIG_SYS_NAND_MAX_OOBFREE 2
#define CONFIG_SYS_NAND_MAX_ECCPOS 56
#define CONFIG_SYS_NAND_U_BOOT_START CONFIG_SYS_TEXT_BASE
-#define CONFIG_SYS_NAND_U_BOOT_OFFS 0x80000
-#define CONFIG_MTD_PARTITIONS /* required for UBI partition support */
-#define CONFIG_MTD_DEVICE /* needed for mtdparts commands */
+#define CONFIG_SYS_NAND_SPL_KERNEL_OFFS 0x2a0000
/* NAND block size is 128 KiB. Synchronize these values with
* corresponding Device Tree entries in Linux:
* MLO(SPL) 4 * NAND_BLOCK_SIZE = 512 KiB @ 0x000000
* DTB 4 * NAND_BLOCK_SIZE = 512 KiB @ 0xAA0000
* RootFS Remaining Flash Space @ 0xB20000
*/
-#endif /* CONFIG_NAND */
+#endif /* CONFIG_MTD_RAW_NAND */
/* Environment information */
#define CONFIG_EXTRA_ENV_SETTINGS \
"loadaddr=0x82000000\0" \
- "console=ttyO2,115200n8\0" \
+ "console=ttyS2,115200n8\0" \
"fdtfile=am3517-evm.dtb\0" \
"fdtaddr=0x82C00000\0" \
"vram=16M\0" \
#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE
/* memtest works on */
-#define CONFIG_SYS_MEMTEST_START (OMAP34XX_SDRC_CS0)
-#define CONFIG_SYS_MEMTEST_END (OMAP34XX_SDRC_CS0 + \
- 0x01F00000) /* 31MB */
/* Physical Memory Map */
#define CONFIG_SYS_CS0_SIZE (256 * 1024 * 1024)
-#define CONFIG_SYS_INIT_RAM_ADDR 0x4020f800
-#define CONFIG_SYS_INIT_RAM_SIZE 0x800
/* FLASH and environment organization */
#define CONFIG_SYS_MAX_FLASH_BANKS 2 /* max number of flash banks */
#define CONFIG_SYS_MONITOR_LEN (256 << 10) /* Reserve 2 sectors */
-#if defined(CONFIG_NAND)
+#if defined(CONFIG_MTD_RAW_NAND)
#define CONFIG_SYS_FLASH_BASE NAND_BASE
#endif
#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_FLASH_BASE
#define CONFIG_SYS_ENV_SECT_SIZE (128 << 10) /* 128 KiB */
-#define CONFIG_ENV_SIZE CONFIG_SYS_ENV_SECT_SIZE
-#define CONFIG_ENV_OFFSET 0x260000
-#define CONFIG_ENV_ADDR 0x260000
/* Defines for SPL */
-#undef CONFIG_SPL_TEXT_BASE
-#define CONFIG_SPL_TEXT_BASE 0x40200000
-#undef CONFIG_SPL_BSS_START_ADDR
-#define CONFIG_SPL_BSS_START_ADDR 0x80000000
-#define CONFIG_SPL_BSS_MAX_SIZE 0x80000 /* 512 KB */
-
-#define CONFIG_SYS_MMCSD_FS_BOOT_PARTITION 1
#define CONFIG_SPL_FS_LOAD_PAYLOAD_NAME "u-boot.img"
-#define CONFIG_SPL_NAND_BASE
-#define CONFIG_SPL_NAND_DRIVERS
-#define CONFIG_SPL_NAND_ECC
-
#endif /* __CONFIG_H */