#define CONFIG_PCIE1 1 /* PCIE controller */
#define CONFIG_FSL_PCI_INIT 1 /* use common fsl pci init code */
#define CONFIG_FSL_PCIE_RESET 1 /* need PCIe reset errata */
+#define CONFIG_SYS_PCI_64BIT 1 /* enable 64-bit PCI resources */
#define CONFIG_TSEC_ENET /* tsec ethernet support */
#define CONFIG_QE /* Enable QE */
#define CONFIG_ENV_OVERWRITE
#define CONFIG_FSL_LAW 1 /* Use common FSL init code */
-/*
- * When initializing flash, if we cannot find the manufacturer ID,
- * assume this is the AMD flash associated with the MDS board.
- * This allows booting from a promjet.
- */
-#define CONFIG_ASSUME_AMD_FLASH
-
#ifndef __ASSEMBLY__
extern unsigned long get_clock_freq(void);
#endif /*Replace a call to get_clock_freq (after it is implemented)*/
*/
#define CONFIG_L2_CACHE /* toggle L2 cache */
#define CONFIG_BTB /* toggle branch predition */
-#define CONFIG_ADDR_STREAMING /* toggle addr streaming */
/*
* Only possible on E500 Version 2 or newer cores.
#define CONFIG_SYS_CCSRBAR_PHYS CONFIG_SYS_CCSRBAR /* physical addr of CCSRBAR */
#define CONFIG_SYS_IMMR CONFIG_SYS_CCSRBAR /* PQII uses CONFIG_SYS_IMMR */
-#define CONFIG_SYS_PCI1_ADDR (CONFIG_SYS_CCSRBAR+0x8000)
-#define CONFIG_SYS_PCIE1_ADDR (CONFIG_SYS_CCSRBAR+0xa000)
-
/* DDR Setup */
#define CONFIG_FSL_DDR2
#undef CONFIG_FSL_DDR_INTERACTIVE
#define CONFIG_SPD_EEPROM /* Use SPD EEPROM for DDR setup*/
#define CONFIG_DDR_SPD
#define CONFIG_DDR_DLL /* possible DLL fix needed */
-#undef CONFIG_ECC_INIT_VIA_DDRCONTROLLER /* DDR controller or DMA? */
+#define CONFIG_ECC_INIT_VIA_DDRCONTROLLER /* DDR controller or DMA? */
#define CONFIG_MEM_INIT_VALUE 0xDeadBeef
#define CONFIG_SYS_FLASH_ERASE_TOUT 60000 /* Flash Erase Timeout (ms) */
#define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (ms) */
-#define CONFIG_SYS_MONITOR_BASE TEXT_BASE /* start of monitor */
+#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE /* start of monitor */
#define CONFIG_FLASH_CFI_DRIVER
#define CONFIG_SYS_FLASH_CFI
#define CONFIG_SYS_LBC_MRTPR 0x00000000 /* LB refresh timer prescal*/
/*
- * LSDMR masks
- */
-#define CONFIG_SYS_LBC_LSDMR_RFEN (1 << (31 - 1))
-#define CONFIG_SYS_LBC_LSDMR_BSMA1516 (3 << (31 - 10))
-#define CONFIG_SYS_LBC_LSDMR_BSMA1617 (4 << (31 - 10))
-#define CONFIG_SYS_LBC_LSDMR_RFCR16 (7 << (31 - 16))
-#define CONFIG_SYS_LBC_LSDMR_PRETOACT7 (7 << (31 - 19))
-#define CONFIG_SYS_LBC_LSDMR_ACTTORW7 (7 << (31 - 22))
-#define CONFIG_SYS_LBC_LSDMR_ACTTORW6 (6 << (31 - 22))
-#define CONFIG_SYS_LBC_LSDMR_BL8 (1 << (31 - 23))
-#define CONFIG_SYS_LBC_LSDMR_WRC4 (0 << (31 - 27))
-#define CONFIG_SYS_LBC_LSDMR_CL3 (3 << (31 - 31))
-
-#define CONFIG_SYS_LBC_LSDMR_OP_NORMAL (0 << (31 - 4))
-#define CONFIG_SYS_LBC_LSDMR_OP_ARFRSH (1 << (31 - 4))
-#define CONFIG_SYS_LBC_LSDMR_OP_SRFRSH (2 << (31 - 4))
-#define CONFIG_SYS_LBC_LSDMR_OP_MRW (3 << (31 - 4))
-#define CONFIG_SYS_LBC_LSDMR_OP_PRECH (4 << (31 - 4))
-#define CONFIG_SYS_LBC_LSDMR_OP_PCHALL (5 << (31 - 4))
-#define CONFIG_SYS_LBC_LSDMR_OP_ACTBNK (6 << (31 - 4))
-#define CONFIG_SYS_LBC_LSDMR_OP_RWINV (7 << (31 - 4))
-
-/*
* Common settings for all Local Bus SDRAM commands.
* At run time, either BSMA1516 (for CPU 1.1)
* or BSMA1617 (for CPU 1.0) (old)
* is OR'ed in too.
*/
-#define CONFIG_SYS_LBC_LSDMR_COMMON ( CONFIG_SYS_LBC_LSDMR_RFCR16 \
- | CONFIG_SYS_LBC_LSDMR_PRETOACT7 \
- | CONFIG_SYS_LBC_LSDMR_ACTTORW7 \
- | CONFIG_SYS_LBC_LSDMR_BL8 \
- | CONFIG_SYS_LBC_LSDMR_WRC4 \
- | CONFIG_SYS_LBC_LSDMR_CL3 \
- | CONFIG_SYS_LBC_LSDMR_RFEN \
+#define CONFIG_SYS_LBC_LSDMR_COMMON ( LSDMR_RFCR16 \
+ | LSDMR_PRETOACT7 \
+ | LSDMR_ACTTORW7 \
+ | LSDMR_BL8 \
+ | LSDMR_WRC4 \
+ | LSDMR_CL3 \
+ | LSDMR_RFEN \
)
/*
#define CONFIG_SYS_BR5_PRELIM 0xf8010801
#define CONFIG_SYS_OR5_PRELIM 0xffff69f7
-#define CONFIG_L1_INIT_RAM
#define CONFIG_SYS_INIT_RAM_LOCK 1
#define CONFIG_SYS_INIT_RAM_ADDR 0xe4010000 /* Initial RAM address */
#define CONFIG_SYS_INIT_RAM_END 0x4000 /* End of used area in RAM */
/* Serial Port */
#define CONFIG_CONS_INDEX 1
-#undef CONFIG_SERIAL_SOFTWARE_FIFO
#define CONFIG_SYS_NS16550
#define CONFIG_SYS_NS16550_SERIAL
#define CONFIG_SYS_NS16550_REG_SIZE 1
#define CONFIG_OF_BOARD_SETUP 1
#define CONFIG_OF_STDOUT_VIA_ALIAS 1
-#define CONFIG_SYS_64BIT_VSPRINTF 1
-#define CONFIG_SYS_64BIT_STRTOUL 1
-
/*
* I2C
*/
#define CONFIG_HARD_I2C /* I2C with hardware support*/
#undef CONFIG_SOFT_I2C /* I2C bit-banged */
#define CONFIG_I2C_MULTI_BUS
-#define CONFIG_I2C_CMD_TREE
#define CONFIG_SYS_I2C_SPEED 400000 /* I2C speed and slave address */
#define CONFIG_SYS_I2C_EEPROM_ADDR 0x52
#define CONFIG_SYS_I2C_SLAVE 0x7F
* General PCI
* Memory Addresses are mapped 1-1. I/O is mapped from 0
*/
-#define CONFIG_SYS_PCI1_MEM_BASE 0x80000000
-#define CONFIG_SYS_PCI1_MEM_PHYS CONFIG_SYS_PCI1_MEM_BASE
+#define CONFIG_SYS_PCI1_MEM_VIRT 0x80000000
+#define CONFIG_SYS_PCI1_MEM_BUS 0x80000000
+#define CONFIG_SYS_PCI1_MEM_PHYS 0x80000000
#define CONFIG_SYS_PCI1_MEM_SIZE 0x20000000 /* 512M */
-#define CONFIG_SYS_PCI1_IO_BASE 0x00000000
+#define CONFIG_SYS_PCI1_IO_VIRT 0xe2000000
+#define CONFIG_SYS_PCI1_IO_BUS 0x00000000
#define CONFIG_SYS_PCI1_IO_PHYS 0xe2000000
#define CONFIG_SYS_PCI1_IO_SIZE 0x00800000 /* 8M */
-#define CONFIG_SYS_PCIE1_MEM_BASE 0xa0000000
-#define CONFIG_SYS_PCIE1_MEM_PHYS CONFIG_SYS_PCIE1_MEM_BASE
+#define CONFIG_SYS_PCIE1_MEM_VIRT 0xa0000000
+#define CONFIG_SYS_PCIE1_MEM_BUS 0xa0000000
+#define CONFIG_SYS_PCIE1_MEM_PHYS 0xa0000000
#define CONFIG_SYS_PCIE1_MEM_SIZE 0x20000000 /* 512M */
-#define CONFIG_SYS_PCIE1_IO_BASE 0x00000000
+#define CONFIG_SYS_PCIE1_IO_VIRT 0xe2800000
+#define CONFIG_SYS_PCIE1_IO_BUS 0x00000000
#define CONFIG_SYS_PCIE1_IO_PHYS 0xe2800000
#define CONFIG_SYS_PCIE1_IO_SIZE 0x00800000 /* 8M */
-#define CONFIG_SYS_SRIO_MEM_BASE 0xc0000000
+#define CONFIG_SYS_SRIO_MEM_VIRT 0xc0000000
+#define CONFIG_SYS_SRIO_MEM_BUS 0xc0000000
+#define CONFIG_SYS_SRIO_MEM_PHYS 0xc0000000
#ifdef CONFIG_QE
/*
*/
#define CONFIG_UEC_ETH
#ifndef CONFIG_TSEC_ENET
-#define CONFIG_ETHPRIME "FSL UEC0"
+#define CONFIG_ETHPRIME "UEC0"
#endif
#define CONFIG_PHY_MODE_NEED_CHANGE
#define CONFIG_eTSEC_MDIO_BUS
#define CONFIG_SYS_UEC1_TX_CLK QE_CLK16
#define CONFIG_SYS_UEC1_ETH_TYPE GIGA_ETH
#define CONFIG_SYS_UEC1_PHY_ADDR 7
-#define CONFIG_SYS_UEC1_INTERFACE_MODE ENET_1000_RGMII_ID
+#define CONFIG_SYS_UEC1_INTERFACE_TYPE RGMII_ID
+#define CONFIG_SYS_UEC1_INTERFACE_SPEED 1000
#endif
#define CONFIG_UEC_ETH2 /* GETH2 */
#define CONFIG_SYS_UEC2_TX_CLK QE_CLK16
#define CONFIG_SYS_UEC2_ETH_TYPE GIGA_ETH
#define CONFIG_SYS_UEC2_PHY_ADDR 1
-#define CONFIG_SYS_UEC2_INTERFACE_MODE ENET_1000_RGMII_ID
+#define CONFIG_SYS_UEC2_INTERFACE_TYPE RGMII_ID
+#define CONFIG_SYS_UEC2_INTERFACE_SPEED 1000
#endif
#endif /* CONFIG_QE */
#undef CONFIG_PCI_SCAN_SHOW /* show pci devices on startup */
#define CONFIG_SYS_PCI_SUBSYS_VENDORID 0x1057 /* Motorola */
-/* PCI view of System Memory */
-#define CONFIG_SYS_PCI_MEMORY_BUS 0x00000000
-#define CONFIG_SYS_PCI_MEMORY_PHYS 0x00000000
-#define CONFIG_SYS_PCI_MEMORY_SIZE 0x80000000
-
#endif /* CONFIG_PCI */
#ifndef CONFIG_NET_MULTI
#define CONFIG_CMD_ELF
#define CONFIG_CMD_IRQ
#define CONFIG_CMD_SETEXPR
+#define CONFIG_CMD_REGINFO
#if defined(CONFIG_PCI)
#define CONFIG_CMD_PCI
* Miscellaneous configurable options
*/
#define CONFIG_SYS_LONGHELP /* undef to save memory */
-#define CONFIG_CMDLINE_EDITING /* Command-line editing */
+#define CONFIG_CMDLINE_EDITING /* Command-line editing */
+#define CONFIG_AUTO_COMPLETE /* add autocompletion support */
#define CONFIG_SYS_LOAD_ADDR 0x2000000 /* default load address */
#define CONFIG_SYS_PROMPT "=> " /* Monitor Command Prompt */
#if defined(CONFIG_CMD_KGDB)
/*
* For booting Linux, the board info and command line data
- * have to be in the first 8 MB of memory, since this is
+ * have to be in the first 16 MB of memory, since this is
* the maximum mapped by the Linux kernel during initialization.
*/
-#define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux*/
+#define CONFIG_SYS_BOOTMAPSZ (16 << 20) /* Initial Memory map for Linux*/
/*
* Internal Definitions
projects / platform / kernel / u-boot.git / blobdiff