- arch/m68k/cpu/mcf532x/config.mk config make
- arch/m68k/cpu/mcf532x/start.S start up assembly code
-- doc/README.m5373evb This readme file
+- board/freescale/m5373evb/README This readme file
- drivers/net/mcffec.c ColdFire common FEC driver
- drivers/serial/mcfuart.c ColdFire common UART driver
- include/asm-m68k/timer.h Timer structure and definition
- include/asm-m68k/types.h Data types definition
- include/asm-m68k/uart.h Uart structure and definition
-- include/asm-m68k/u-boot.h u-boot structure
+- include/asm-m68k/u-boot.h U-Boot structure
- include/configs/M5373EVB.h Board specific configuration file
CONFIG_M5373EVB -- define for M5373EVB board
CONFIG_MCFUART -- define to use common CF Uart driver
-CONFIG_SYS_UART_PORT -- define UART port number, start with 0, 1 and 2
+CFG_SYS_UART_PORT -- define UART port number, start with 0, 1 and 2
CONFIG_BAUDRATE -- define UART baudrate
CONFIG_MCFRTC -- define to use common CF RTC driver
CONFIG_SYS_MCFRTC_BASE -- provide base address for RTC in immap.h
CONFIG_SYS_RTC_OSCILLATOR -- define RTC clock frequency
RTC_DEBUG -- define to show RTC debug message
-CONFIG_CMD_DATE -- enable to use date feature in u-boot
+CONFIG_CMD_DATE -- enable to use date feature in U-Boot
CONFIG_MCFFEC -- define to use common CF FEC driver
CONFIG_MII -- enable to use MII driver
CONFIG_SYS_FEC0_MIIBASE -- Set FEC0 MII base register
MCFFEC_TOUT_LOOP -- set FEC timeout loop
-CONFIG_MCFTMR -- define to use DMA timer
-CONFIG_MCFPIT -- define to use PIT timer
+CFG_MCFTMR -- define to use DMA timer
-CONFIG_FSL_I2C -- define to use FSL common I2C driver
-CONFIG_HARD_I2C -- define for I2C hardware support
-CONFIG_SOFT_I2C -- define for I2C bit-banged
+CONFIG_SYS_I2C_FSL -- define to use FSL common I2C driver
+CONFIG_SYS_I2C_SOFT -- define for I2C bit-banged
CONFIG_SYS_I2C_SPEED -- define for I2C speed
CONFIG_SYS_I2C_SLAVE -- define for I2C slave address
CONFIG_SYS_I2C_OFFSET -- define for I2C base address offset
CONFIG_SYS_IMMR -- define for MBAR offset
-CONFIG_SYS_MBAR -- define MBAR offset
+CFG_SYS_MBAR -- define MBAR offset
CONFIG_MONITOR_IS_IN_RAM -- Not support
-CONFIG_SYS_INIT_RAM_ADDR -- defines the base address of the MCF5373 internal SRAM
+CFG_SYS_INIT_RAM_ADDR -- defines the base address of the MCF5373 internal SRAM
CONFIG_SYS_CSn_BASE -- defines the Chip Select Base register
CONFIG_SYS_CSn_MASK -- defines the Chip Select Mask register
CONFIG_SYS_CSn_CTRL -- defines the Chip Select Control register
-CONFIG_SYS_SDRAM_BASE -- defines the DRAM Base
+CFG_SYS_SDRAM_BASE -- defines the DRAM Base
2. MEMORY MAP UNDER U-BOOT AND LINUX KERNEL
===========================================
SRAM: 0x80000000-0x8FFFFFFF (256MB)
IP: 0xF0000000-0xFFFFFFFF (256MB)
-2.2. For the initial bringup, we adopted a consistent memory scheme between u-boot and
+2.2. For the initial bringup, we adopted a consistent memory scheme between U-Boot and
linux kernel, you can customize it based on your system requirements:
Flash0: 0x00000000-0x00FFFFFF (16MB)