include/configs/T208xQDS.h

   1 /* SPDX-License-Identifier: GPL-2.0+ */
   2 /*
   3  * Copyright 2011-2013 Freescale Semiconductor, Inc.
   4  * Copyright 2020-2021 NXP
   5  */
   6
   7 /*
   8  * T2080/T2081 QDS board configuration file
   9  */
  10
  11 #ifndef __T208xQDS_H
  12 #define __T208xQDS_H
  13
  14 #include <linux/stringify.h>
  15
  16 #define CONFIG_ICS307_REFCLK_HZ 25000000  /* ICS307 ref clk freq */
  17 #if defined(CONFIG_ARCH_T2080)
  18 #define CONFIG_FSL_SATA_V2
  19 #define CONFIG_SYS_SRIO         /* Enable Serial RapidIO Support */
  20 #define CONFIG_SRIO1            /* SRIO port 1 */
  21 #define CONFIG_SRIO2            /* SRIO port 2 */
  22 #endif
  23
  24 /* High Level Configuration Options */
  25 #define CONFIG_SYS_BOOK3E_HV    /* Category E.HV supported */
  26 #define CONFIG_ENABLE_36BIT_PHYS
  27
  28 #define CONFIG_SYS_FSL_CPC      /* Corenet Platform Cache */
  29 #define CONFIG_SYS_NUM_CPC      CONFIG_SYS_NUM_DDR_CTLRS
  30
  31 #ifdef CONFIG_RAMBOOT_PBL
  32 #define CONFIG_SPL_FLUSH_IMAGE
  33 #define CONFIG_SPL_PAD_TO               0x40000
  34 #define CONFIG_SPL_MAX_SIZE             0x28000
  35 #define RESET_VECTOR_OFFSET             0x27FFC
  36 #define BOOT_PAGE_OFFSET                0x27000
  37 #ifdef CONFIG_SPL_BUILD
  38 #define CONFIG_SPL_SKIP_RELOCATE
  39 #define CONFIG_SPL_COMMON_INIT_DDR
  40 #define CONFIG_SYS_CCSR_DO_NOT_RELOCATE
  41 #endif
  42
  43 #ifdef CONFIG_MTD_RAW_NAND
  44 #define CONFIG_SYS_NAND_U_BOOT_SIZE     (768 << 10)
  45 #define CONFIG_SYS_NAND_U_BOOT_DST      0x00200000
  46 #define CONFIG_SYS_NAND_U_BOOT_START    0x00200000
  47 #define CONFIG_SYS_NAND_U_BOOT_OFFS     (256 << 10)
  48 #endif
  49
  50 #ifdef CONFIG_SPIFLASH
  51 #define CONFIG_RESET_VECTOR_ADDRESS             0x200FFC
  52 #define CONFIG_SPL_SPI_FLASH_MINIMAL
  53 #define CONFIG_SYS_SPI_FLASH_U_BOOT_SIZE        (768 << 10)
  54 #define CONFIG_SYS_SPI_FLASH_U_BOOT_DST         (0x00200000)
  55 #define CONFIG_SYS_SPI_FLASH_U_BOOT_START       (0x00200000)
  56 #define CONFIG_SYS_SPI_FLASH_U_BOOT_OFFS        (256 << 10)
  57 #ifndef CONFIG_SPL_BUILD
  58 #define CONFIG_SYS_MPC85XX_NO_RESETVEC
  59 #endif
  60 #endif
  61
  62 #ifdef CONFIG_SDCARD
  63 #define CONFIG_RESET_VECTOR_ADDRESS             0x200FFC
  64 #define CONFIG_SYS_MMC_U_BOOT_SIZE      (768 << 10)
  65 #define CONFIG_SYS_MMC_U_BOOT_DST       (0x00200000)
  66 #define CONFIG_SYS_MMC_U_BOOT_START     (0x00200000)
  67 #define CONFIG_SYS_MMC_U_BOOT_OFFS      (260 << 10)
  68 #ifndef CONFIG_SPL_BUILD
  69 #define CONFIG_SYS_MPC85XX_NO_RESETVEC
  70 #endif
  71 #endif
  72
  73 #endif /* CONFIG_RAMBOOT_PBL */
  74
  75 #define CONFIG_SRIO_PCIE_BOOT_MASTER
  76 #ifdef CONFIG_SRIO_PCIE_BOOT_SLAVE
  77 /* Set 1M boot space */
  78 #define CONFIG_SYS_SRIO_PCIE_BOOT_SLAVE_ADDR (CONFIG_SYS_TEXT_BASE & 0xfff00000)
  79 #define CONFIG_SYS_SRIO_PCIE_BOOT_SLAVE_ADDR_PHYS \
  80                 (0x300000000ull | CONFIG_SYS_SRIO_PCIE_BOOT_SLAVE_ADDR)
  81 #define CONFIG_RESET_VECTOR_ADDRESS 0xfffffffc
  82 #endif
  83
  84 #ifndef CONFIG_RESET_VECTOR_ADDRESS
  85 #define CONFIG_RESET_VECTOR_ADDRESS     0xeffffffc
  86 #endif
  87
  88 /*
  89  * These can be toggled for performance analysis, otherwise use default.
  90  */
  91 #define CONFIG_SYS_CACHE_STASHING
  92 #define CONFIG_BTB              /* toggle branch predition */
  93 #ifdef CONFIG_DDR_ECC
  94 #define CONFIG_MEM_INIT_VALUE           0xdeadbeef
  95 #endif
  96
  97 #ifndef __ASSEMBLY__
  98 unsigned long get_board_sys_clk(void);
  99 #endif
 100
 101 #define CONFIG_SYS_CLK_FREQ     get_board_sys_clk()
 102
 103 /*
 104  * Config the L3 Cache as L3 SRAM
 105  */
 106 #define CONFIG_SYS_INIT_L3_ADDR         0xFFFC0000
 107 #define CONFIG_SYS_L3_SIZE              (512 << 10)
 108 #define CONFIG_SPL_GD_ADDR              (CONFIG_SYS_INIT_L3_ADDR + 32 * 1024)
 109 #define SPL_ENV_ADDR                    (CONFIG_SPL_GD_ADDR + 4 * 1024)
 110 #define CONFIG_SPL_RELOC_MALLOC_ADDR    (CONFIG_SPL_GD_ADDR + 12 * 1024)
 111 #define CONFIG_SPL_RELOC_MALLOC_SIZE    (50 << 10)
 112 #define CONFIG_SPL_RELOC_STACK          (CONFIG_SPL_GD_ADDR + 64 * 1024)
 113
 114 #define CONFIG_SYS_DCSRBAR      0xf0000000
 115 #define CONFIG_SYS_DCSRBAR_PHYS 0xf00000000ull
 116
 117 /* EEPROM */
 118 #define CONFIG_SYS_I2C_EEPROM_NXID
 119 #define CONFIG_SYS_EEPROM_BUS_NUM       0
 120
 121 /*
 122  * DDR Setup
 123  */
 124 #define CONFIG_VERY_BIG_RAM
 125 #define CONFIG_SYS_DDR_SDRAM_BASE       0x00000000
 126 #define CONFIG_SYS_SDRAM_BASE           CONFIG_SYS_DDR_SDRAM_BASE
 127 #define CONFIG_DIMM_SLOTS_PER_CTLR      2
 128 #define CONFIG_CHIP_SELECTS_PER_CTRL    (2 * CONFIG_DIMM_SLOTS_PER_CTLR)
 129 #define CONFIG_SYS_SPD_BUS_NUM  0
 130 #define CONFIG_SYS_SDRAM_SIZE   2048    /* for fixed parameter use */
 131 #define SPD_EEPROM_ADDRESS1     0x51
 132 #define SPD_EEPROM_ADDRESS2     0x52
 133 #define SPD_EEPROM_ADDRESS      SPD_EEPROM_ADDRESS1
 134 #define CTRL_INTLV_PREFERED     cacheline
 135
 136 /*
 137  * IFC Definitions
 138  */
 139 #define CONFIG_SYS_FLASH_BASE           0xe0000000
 140 #define CONFIG_SYS_FLASH_BASE_PHYS      (0xf00000000ull | CONFIG_SYS_FLASH_BASE)
 141 #define CONFIG_SYS_NOR0_CSPR_EXT        (0xf)
 142 #define CONFIG_SYS_NOR0_CSPR    (CSPR_PHYS_ADDR(CONFIG_SYS_FLASH_BASE_PHYS \
 143                                 + 0x8000000) | \
 144                                 CSPR_PORT_SIZE_16 | \
 145                                 CSPR_MSEL_NOR | \
 146                                 CSPR_V)
 147 #define CONFIG_SYS_NOR1_CSPR_EXT        (0xf)
 148 #define CONFIG_SYS_NOR1_CSPR    (CSPR_PHYS_ADDR(CONFIG_SYS_FLASH_BASE_PHYS) | \
 149                                 CSPR_PORT_SIZE_16 | \
 150                                 CSPR_MSEL_NOR | \
 151                                 CSPR_V)
 152 #define CONFIG_SYS_NOR_AMASK    IFC_AMASK(128*1024*1024)
 153 /* NOR Flash Timing Params */
 154 #define CONFIG_SYS_NOR_CSOR     CSOR_NAND_TRHZ_80
 155
 156 #define CONFIG_SYS_NOR_FTIM0    (FTIM0_NOR_TACSE(0x4) | \
 157                                 FTIM0_NOR_TEADC(0x5) | \
 158                                 FTIM0_NOR_TEAHC(0x5))
 159 #define CONFIG_SYS_NOR_FTIM1    (FTIM1_NOR_TACO(0x35) | \
 160                                 FTIM1_NOR_TRAD_NOR(0x1A) |\
 161                                 FTIM1_NOR_TSEQRAD_NOR(0x13))
 162 #define CONFIG_SYS_NOR_FTIM2    (FTIM2_NOR_TCS(0x4) | \
 163                                 FTIM2_NOR_TCH(0x4) | \
 164                                 FTIM2_NOR_TWPH(0x0E) | \
 165                                 FTIM2_NOR_TWP(0x1c))
 166 #define CONFIG_SYS_NOR_FTIM3    0x0
 167
 168 #define CONFIG_SYS_FLASH_QUIET_TEST
 169 #define CONFIG_FLASH_SHOW_PROGRESS      45 /* count down from 45/5: 9..1 */
 170
 171 #define CONFIG_SYS_MAX_FLASH_BANKS      2       /* number of banks */
 172 #define CONFIG_SYS_MAX_FLASH_SECT       1024    /* sectors per device */
 173 #define CONFIG_SYS_FLASH_ERASE_TOUT     60000   /* Flash Erase Timeout (ms) */
 174 #define CONFIG_SYS_FLASH_WRITE_TOUT     500     /* Flash Write Timeout (ms) */
 175
 176 #define CONFIG_SYS_FLASH_EMPTY_INFO
 177 #define CONFIG_SYS_FLASH_BANKS_LIST     {CONFIG_SYS_FLASH_BASE_PHYS \
 178                                         + 0x8000000, CONFIG_SYS_FLASH_BASE_PHYS}
 179
 180 #define CONFIG_FSL_QIXIS        /* use common QIXIS code */
 181 #define QIXIS_BASE                      0xffdf0000
 182 #define QIXIS_LBMAP_SWITCH              6
 183 #define QIXIS_LBMAP_MASK                0x0f
 184 #define QIXIS_LBMAP_SHIFT               0
 185 #define QIXIS_LBMAP_DFLTBANK            0x00
 186 #define QIXIS_LBMAP_ALTBANK             0x04
 187 #define QIXIS_LBMAP_NAND                0x09
 188 #define QIXIS_LBMAP_SD                  0x00
 189 #define QIXIS_RCW_SRC_NAND              0x104
 190 #define QIXIS_RCW_SRC_SD                0x040
 191 #define QIXIS_RST_CTL_RESET             0x83
 192 #define QIXIS_RST_FORCE_MEM             0x1
 193 #define QIXIS_RCFG_CTL_RECONFIG_IDLE    0x20
 194 #define QIXIS_RCFG_CTL_RECONFIG_START   0x21
 195 #define QIXIS_RCFG_CTL_WATCHDOG_ENBLE   0x08
 196 #define QIXIS_BASE_PHYS         (0xf00000000ull | QIXIS_BASE)
 197
 198 #define CONFIG_SYS_CSPR3_EXT    (0xf)
 199 #define CONFIG_SYS_CSPR3        (CSPR_PHYS_ADDR(QIXIS_BASE_PHYS) \
 200                                 | CSPR_PORT_SIZE_8 \
 201                                 | CSPR_MSEL_GPCM \
 202                                 | CSPR_V)
 203 #define CONFIG_SYS_AMASK3       IFC_AMASK(64 * 1024)
 204 #define CONFIG_SYS_CSOR3        0x0
 205 /* QIXIS Timing parameters for IFC CS3 */
 206 #define CONFIG_SYS_CS3_FTIM0            (FTIM0_GPCM_TACSE(0x0e) | \
 207                                         FTIM0_GPCM_TEADC(0x0e) | \
 208                                         FTIM0_GPCM_TEAHC(0x0e))
 209 #define CONFIG_SYS_CS3_FTIM1            (FTIM1_GPCM_TACO(0xff) | \
 210                                         FTIM1_GPCM_TRAD(0x3f))
 211 #define CONFIG_SYS_CS3_FTIM2            (FTIM2_GPCM_TCS(0x0e) | \
 212                                         FTIM2_GPCM_TCH(0x8) | \
 213                                         FTIM2_GPCM_TWP(0x1f))
 214 #define CONFIG_SYS_CS3_FTIM3            0x0
 215
 216 /* NAND Flash on IFC */
 217 #define CONFIG_NAND_FSL_IFC
 218 #define CONFIG_SYS_NAND_BASE            0xff800000
 219 #define CONFIG_SYS_NAND_BASE_PHYS       (0xf00000000ull | CONFIG_SYS_NAND_BASE)
 220
 221 #define CONFIG_SYS_NAND_CSPR_EXT        (0xf)
 222 #define CONFIG_SYS_NAND_CSPR    (CSPR_PHYS_ADDR(CONFIG_SYS_NAND_BASE_PHYS) \
 223                                 | CSPR_PORT_SIZE_8 /* Port Size = 8 bit */ \
 224                                 | CSPR_MSEL_NAND         /* MSEL = NAND */ \
 225                                 | CSPR_V)
 226 #define CONFIG_SYS_NAND_AMASK   IFC_AMASK(64*1024)
 227
 228 #define CONFIG_SYS_NAND_CSOR    (CSOR_NAND_ECC_ENC_EN   /* ECC on encode */ \
 229                                 | CSOR_NAND_ECC_DEC_EN  /* ECC on decode */ \
 230                                 | CSOR_NAND_ECC_MODE_4  /* 4-bit ECC */     \
 231                                 | CSOR_NAND_RAL_3       /* RAL = 2Byes */   \
 232                                 | CSOR_NAND_PGS_2K      /* Page Size = 2K */\
 233                                 | CSOR_NAND_SPRZ_64     /* Spare size = 64 */\
 234                                 | CSOR_NAND_PB(64))     /*Pages Per Block = 64*/
 235
 236 #define CONFIG_SYS_NAND_ONFI_DETECTION
 237
 238 /* ONFI NAND Flash mode0 Timing Params */
 239 #define CONFIG_SYS_NAND_FTIM0           (FTIM0_NAND_TCCST(0x07) | \
 240                                         FTIM0_NAND_TWP(0x18)    | \
 241                                         FTIM0_NAND_TWCHT(0x07)  | \
 242                                         FTIM0_NAND_TWH(0x0a))
 243 #define CONFIG_SYS_NAND_FTIM1           (FTIM1_NAND_TADLE(0x32) | \
 244                                         FTIM1_NAND_TWBE(0x39)   | \
 245                                         FTIM1_NAND_TRR(0x0e)    | \
 246                                         FTIM1_NAND_TRP(0x18))
 247 #define CONFIG_SYS_NAND_FTIM2           (FTIM2_NAND_TRAD(0x0f)  | \
 248                                         FTIM2_NAND_TREH(0x0a)   | \
 249                                         FTIM2_NAND_TWHRE(0x1e))
 250 #define CONFIG_SYS_NAND_FTIM3           0x0
 251
 252 #define CONFIG_SYS_NAND_DDR_LAW         11
 253 #define CONFIG_SYS_NAND_BASE_LIST       { CONFIG_SYS_NAND_BASE }
 254 #define CONFIG_SYS_MAX_NAND_DEVICE      1
 255
 256 #if defined(CONFIG_MTD_RAW_NAND)
 257 #define CONFIG_SYS_CSPR0_EXT            CONFIG_SYS_NAND_CSPR_EXT
 258 #define CONFIG_SYS_CSPR0                CONFIG_SYS_NAND_CSPR
 259 #define CONFIG_SYS_AMASK0               CONFIG_SYS_NAND_AMASK
 260 #define CONFIG_SYS_CSOR0                CONFIG_SYS_NAND_CSOR
 261 #define CONFIG_SYS_CS0_FTIM0            CONFIG_SYS_NAND_FTIM0
 262 #define CONFIG_SYS_CS0_FTIM1            CONFIG_SYS_NAND_FTIM1
 263 #define CONFIG_SYS_CS0_FTIM2            CONFIG_SYS_NAND_FTIM2
 264 #define CONFIG_SYS_CS0_FTIM3            CONFIG_SYS_NAND_FTIM3
 265 #define CONFIG_SYS_CSPR1_EXT            CONFIG_SYS_NOR0_CSPR_EXT
 266 #define CONFIG_SYS_CSPR1                CONFIG_SYS_NOR0_CSPR
 267 #define CONFIG_SYS_AMASK1               CONFIG_SYS_NOR_AMASK
 268 #define CONFIG_SYS_CSOR1                CONFIG_SYS_NOR_CSOR
 269 #define CONFIG_SYS_CS1_FTIM0            CONFIG_SYS_NOR_FTIM0
 270 #define CONFIG_SYS_CS1_FTIM1            CONFIG_SYS_NOR_FTIM1
 271 #define CONFIG_SYS_CS1_FTIM2            CONFIG_SYS_NOR_FTIM2
 272 #define CONFIG_SYS_CS1_FTIM3            CONFIG_SYS_NOR_FTIM3
 273 #define CONFIG_SYS_CSPR2_EXT            CONFIG_SYS_NOR1_CSPR_EXT
 274 #define CONFIG_SYS_CSPR2                CONFIG_SYS_NOR1_CSPR
 275 #define CONFIG_SYS_AMASK2               CONFIG_SYS_NOR_AMASK
 276 #define CONFIG_SYS_CSOR2                CONFIG_SYS_NOR_CSOR
 277 #define CONFIG_SYS_CS2_FTIM0            CONFIG_SYS_NOR_FTIM0
 278 #define CONFIG_SYS_CS2_FTIM1            CONFIG_SYS_NOR_FTIM1
 279 #define CONFIG_SYS_CS2_FTIM2            CONFIG_SYS_NOR_FTIM2
 280 #define CONFIG_SYS_CS2_FTIM3            CONFIG_SYS_NOR_FTIM3
 281 #else
 282 #define CONFIG_SYS_CSPR0_EXT            CONFIG_SYS_NOR0_CSPR_EXT
 283 #define CONFIG_SYS_CSPR0                CONFIG_SYS_NOR0_CSPR
 284 #define CONFIG_SYS_AMASK0               CONFIG_SYS_NOR_AMASK
 285 #define CONFIG_SYS_CSOR0                CONFIG_SYS_NOR_CSOR
 286 #define CONFIG_SYS_CS0_FTIM0            CONFIG_SYS_NOR_FTIM0
 287 #define CONFIG_SYS_CS0_FTIM1            CONFIG_SYS_NOR_FTIM1
 288 #define CONFIG_SYS_CS0_FTIM2            CONFIG_SYS_NOR_FTIM2
 289 #define CONFIG_SYS_CS0_FTIM3            CONFIG_SYS_NOR_FTIM3
 290 #define CONFIG_SYS_CSPR1_EXT            CONFIG_SYS_NOR1_CSPR_EXT
 291 #define CONFIG_SYS_CSPR1                CONFIG_SYS_NOR1_CSPR
 292 #define CONFIG_SYS_AMASK1               CONFIG_SYS_NOR_AMASK
 293 #define CONFIG_SYS_CSOR1                CONFIG_SYS_NOR_CSOR
 294 #define CONFIG_SYS_CS1_FTIM0            CONFIG_SYS_NOR_FTIM0
 295 #define CONFIG_SYS_CS1_FTIM1            CONFIG_SYS_NOR_FTIM1
 296 #define CONFIG_SYS_CS1_FTIM2            CONFIG_SYS_NOR_FTIM2
 297 #define CONFIG_SYS_CS1_FTIM3            CONFIG_SYS_NOR_FTIM3
 298 #define CONFIG_SYS_CSPR2_EXT            CONFIG_SYS_NAND_CSPR_EXT
 299 #define CONFIG_SYS_CSPR2                CONFIG_SYS_NAND_CSPR
 300 #define CONFIG_SYS_AMASK2               CONFIG_SYS_NAND_AMASK
 301 #define CONFIG_SYS_CSOR2                CONFIG_SYS_NAND_CSOR
 302 #define CONFIG_SYS_CS2_FTIM0            CONFIG_SYS_NAND_FTIM0
 303 #define CONFIG_SYS_CS2_FTIM1            CONFIG_SYS_NAND_FTIM1
 304 #define CONFIG_SYS_CS2_FTIM2            CONFIG_SYS_NAND_FTIM2
 305 #define CONFIG_SYS_CS2_FTIM3            CONFIG_SYS_NAND_FTIM3
 306 #endif
 307
 308 #if defined(CONFIG_RAMBOOT_PBL)
 309 #define CONFIG_SYS_RAMBOOT
 310 #endif
 311
 312 #ifdef CONFIG_SPL_BUILD
 313 #define CONFIG_SYS_MONITOR_BASE CONFIG_SPL_TEXT_BASE
 314 #else
 315 #define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE    /* start of monitor */
 316 #endif
 317
 318 #define CONFIG_HWCONFIG
 319
 320 /* define to use L1 as initial stack */
 321 #define CONFIG_L1_INIT_RAM
 322 #define CONFIG_SYS_INIT_RAM_LOCK
 323 #define CONFIG_SYS_INIT_RAM_ADDR        0xfdd00000 /* Initial L1 address */
 324 #define CONFIG_SYS_INIT_RAM_ADDR_PHYS_HIGH      0xf
 325 #define CONFIG_SYS_INIT_RAM_ADDR_PHYS_LOW       0xfe03c000
 326 /* The assembler doesn't like typecast */
 327 #define CONFIG_SYS_INIT_RAM_ADDR_PHYS \
 328                         ((CONFIG_SYS_INIT_RAM_ADDR_PHYS_HIGH * 1ull << 32) | \
 329                         CONFIG_SYS_INIT_RAM_ADDR_PHYS_LOW)
 330 #define CONFIG_SYS_INIT_RAM_SIZE        0x00004000
 331 #define CONFIG_SYS_GBL_DATA_OFFSET      (CONFIG_SYS_INIT_RAM_SIZE - \
 332                                                 GENERATED_GBL_DATA_SIZE)
 333 #define CONFIG_SYS_INIT_SP_OFFSET       CONFIG_SYS_GBL_DATA_OFFSET
 334 #define CONFIG_SYS_MONITOR_LEN          (768 * 1024)
 335
 336 /*
 337  * Serial Port
 338  */
 339 #define CONFIG_SYS_NS16550_SERIAL
 340 #define CONFIG_SYS_NS16550_REG_SIZE     1
 341 #define CONFIG_SYS_NS16550_CLK          (get_bus_freq(0)/2)
 342 #define CONFIG_SYS_BAUDRATE_TABLE       \
 343         {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200}
 344 #define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_CCSRBAR+0x11C500)
 345 #define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_CCSRBAR+0x11C600)
 346 #define CONFIG_SYS_NS16550_COM3 (CONFIG_SYS_CCSRBAR+0x11D500)
 347 #define CONFIG_SYS_NS16550_COM4 (CONFIG_SYS_CCSRBAR+0x11D600)
 348
 349 /*
 350  * I2C
 351  */
 352
 353 #define I2C_MUX_PCA_ADDR_PRI    0x77 /* I2C bus multiplexer,primary */
 354 #define I2C_MUX_PCA_ADDR_SEC1   0x75 /* I2C bus multiplexer,secondary 1 */
 355 #define I2C_MUX_PCA_ADDR_SEC2   0x76 /* I2C bus multiplexer,secondary 2 */
 356 #define I2C_MUX_CH_DEFAULT      0x8
 357
 358 #define I2C_MUX_CH_VOL_MONITOR 0xa
 359
 360 /* Voltage monitor on channel 2*/
 361 #define I2C_VOL_MONITOR_ADDR           0x40
 362 #define I2C_VOL_MONITOR_BUS_V_OFFSET   0x2
 363 #define I2C_VOL_MONITOR_BUS_V_OVF      0x1
 364 #define I2C_VOL_MONITOR_BUS_V_SHIFT    3
 365
 366 #define CONFIG_VID_FLS_ENV              "t208xqds_vdd_mv"
 367 #ifndef CONFIG_SPL_BUILD
 368 #define CONFIG_VID
 369 #endif
 370 #define CONFIG_VOL_MONITOR_IR36021_SET
 371 #define CONFIG_VOL_MONITOR_IR36021_READ
 372 /* The lowest and highest voltage allowed for T208xQDS */
 373 #define VDD_MV_MIN                      819
 374 #define VDD_MV_MAX                      1212
 375
 376 /*
 377  * RapidIO
 378  */
 379 #define CONFIG_SYS_SRIO1_MEM_VIRT       0xa0000000
 380 #define CONFIG_SYS_SRIO1_MEM_PHYS       0xc20000000ull
 381 #define CONFIG_SYS_SRIO1_MEM_SIZE       0x10000000 /* 256M */
 382 #define CONFIG_SYS_SRIO2_MEM_VIRT       0xb0000000
 383 #define CONFIG_SYS_SRIO2_MEM_PHYS       0xc30000000ull
 384 #define CONFIG_SYS_SRIO2_MEM_SIZE       0x10000000 /* 256M */
 385 /*
 386  * for slave u-boot IMAGE instored in master memory space,
 387  * PHYS must be aligned based on the SIZE
 388  */
 389 #define CONFIG_SRIO_PCIE_BOOT_IMAGE_MEM_PHYS 0xfef200000ull
 390 #define CONFIG_SRIO_PCIE_BOOT_IMAGE_MEM_BUS1 0xfff00000ull
 391 #define CONFIG_SRIO_PCIE_BOOT_IMAGE_SIZE     0x100000 /* 1M */
 392 #define CONFIG_SRIO_PCIE_BOOT_IMAGE_MEM_BUS2 0x3fff00000ull
 393 /*
 394  * for slave UCODE and ENV instored in master memory space,
 395  * PHYS must be aligned based on the SIZE
 396  */
 397 #define CONFIG_SRIO_PCIE_BOOT_UCODE_ENV_MEM_PHYS 0xfef100000ull
 398 #define CONFIG_SRIO_PCIE_BOOT_UCODE_ENV_MEM_BUS 0x3ffe00000ull
 399 #define CONFIG_SRIO_PCIE_BOOT_UCODE_ENV_SIZE    0x40000 /* 256K */
 400
 401 /* slave core release by master*/
 402 #define CONFIG_SRIO_PCIE_BOOT_BRR_OFFSET 0xe00e4
 403 #define CONFIG_SRIO_PCIE_BOOT_RELEASE_MASK 0x00000001 /* release core 0 */
 404
 405 /*
 406  * SRIO_PCIE_BOOT - SLAVE
 407  */
 408 #ifdef CONFIG_SRIO_PCIE_BOOT_SLAVE
 409 #define CONFIG_SYS_SRIO_PCIE_BOOT_UCODE_ENV_ADDR 0xFFE00000
 410 #define CONFIG_SYS_SRIO_PCIE_BOOT_UCODE_ENV_ADDR_PHYS \
 411                 (0x300000000ull | CONFIG_SYS_SRIO_PCIE_BOOT_UCODE_ENV_ADDR)
 412 #endif
 413
 414 /*
 415  * eSPI - Enhanced SPI
 416  */
 417
 418 /*
 419  * General PCI
 420  * Memory space is mapped 1-1, but I/O space must start from 0.
 421  */
 422 #define CONFIG_PCIE1            /* PCIE controller 1 */
 423 #define CONFIG_PCIE2            /* PCIE controller 2 */
 424 #define CONFIG_PCIE3            /* PCIE controller 3 */
 425 #define CONFIG_PCIE4            /* PCIE controller 4 */
 426 #define CONFIG_SYS_PCI_64BIT    /* enable 64-bit PCI resources */
 427 /* controller 1, direct to uli, tgtid 3, Base address 20000 */
 428 #define CONFIG_SYS_PCIE1_MEM_VIRT       0x80000000
 429 #define CONFIG_SYS_PCIE1_MEM_PHYS       0xc00000000ull
 430 #define CONFIG_SYS_PCIE1_IO_VIRT        0xf8000000
 431 #define CONFIG_SYS_PCIE1_IO_PHYS        0xff8000000ull
 432
 433 /* controller 2, Slot 2, tgtid 2, Base address 201000 */
 434 #define CONFIG_SYS_PCIE2_MEM_VIRT       0xa0000000
 435 #define CONFIG_SYS_PCIE2_MEM_PHYS       0xc20000000ull
 436 #define CONFIG_SYS_PCIE2_IO_VIRT        0xf8010000
 437 #define CONFIG_SYS_PCIE2_IO_PHYS        0xff8010000ull
 438
 439 /* controller 3, Slot 1, tgtid 1, Base address 202000 */
 440 #define CONFIG_SYS_PCIE3_MEM_VIRT       0xb0000000
 441 #define CONFIG_SYS_PCIE3_MEM_PHYS       0xc30000000ull
 442 #define CONFIG_SYS_PCIE3_IO_VIRT        0xf8020000
 443 #define CONFIG_SYS_PCIE3_IO_PHYS        0xff8020000ull
 444
 445 /* controller 4, Base address 203000 */
 446 #define CONFIG_SYS_PCIE4_MEM_VIRT       0xc0000000
 447 #define CONFIG_SYS_PCIE4_MEM_PHYS       0xc40000000ull
 448 #define CONFIG_SYS_PCIE4_IO_PHYS        0xff8030000ull
 449
 450 #ifdef CONFIG_PCI
 451 #define CONFIG_PCI_SCAN_SHOW    /* show pci devices on startup */
 452 #endif
 453
 454 /* Qman/Bman */
 455 #ifndef CONFIG_NOBQFMAN
 456 #define CONFIG_SYS_BMAN_NUM_PORTALS     18
 457 #define CONFIG_SYS_BMAN_MEM_BASE        0xf4000000
 458 #define CONFIG_SYS_BMAN_MEM_PHYS        0xff4000000ull
 459 #define CONFIG_SYS_BMAN_MEM_SIZE        0x02000000
 460 #define CONFIG_SYS_BMAN_SP_CENA_SIZE    0x4000
 461 #define CONFIG_SYS_BMAN_SP_CINH_SIZE    0x1000
 462 #define CONFIG_SYS_BMAN_CENA_BASE       CONFIG_SYS_BMAN_MEM_BASE
 463 #define CONFIG_SYS_BMAN_CENA_SIZE       (CONFIG_SYS_BMAN_MEM_SIZE >> 1)
 464 #define CONFIG_SYS_BMAN_CINH_BASE       (CONFIG_SYS_BMAN_MEM_BASE + \
 465                                         CONFIG_SYS_BMAN_CENA_SIZE)
 466 #define CONFIG_SYS_BMAN_CINH_SIZE       (CONFIG_SYS_BMAN_MEM_SIZE >> 1)
 467 #define CONFIG_SYS_BMAN_SWP_ISDR_REG    0xE08
 468 #define CONFIG_SYS_QMAN_NUM_PORTALS     18
 469 #define CONFIG_SYS_QMAN_MEM_BASE        0xf6000000
 470 #define CONFIG_SYS_QMAN_MEM_PHYS        0xff6000000ull
 471 #define CONFIG_SYS_QMAN_MEM_SIZE        0x02000000
 472 #define CONFIG_SYS_QMAN_SP_CENA_SIZE    0x4000
 473 #define CONFIG_SYS_QMAN_SP_CINH_SIZE    0x1000
 474 #define CONFIG_SYS_QMAN_CENA_BASE       CONFIG_SYS_QMAN_MEM_BASE
 475 #define CONFIG_SYS_QMAN_CENA_SIZE       (CONFIG_SYS_QMAN_MEM_SIZE >> 1)
 476 #define CONFIG_SYS_QMAN_CINH_BASE       (CONFIG_SYS_QMAN_MEM_BASE + \
 477                                         CONFIG_SYS_QMAN_CENA_SIZE)
 478 #define CONFIG_SYS_QMAN_CINH_SIZE       (CONFIG_SYS_QMAN_MEM_SIZE >> 1)
 479 #define CONFIG_SYS_QMAN_SWP_ISDR_REG    0xE08
 480
 481 #define CONFIG_SYS_DPAA_FMAN
 482 #define CONFIG_SYS_DPAA_PME
 483 #define CONFIG_SYS_PMAN
 484 #define CONFIG_SYS_DPAA_DCE
 485 #define CONFIG_SYS_DPAA_RMAN            /* RMan */
 486 #define CONFIG_SYS_INTERLAKEN
 487
 488 /* Default address of microcode for the Linux Fman driver */
 489 #if defined(CONFIG_SPIFLASH)
 490 /*
 491  * env is stored at 0x100000, sector size is 0x10000, ucode is stored after
 492  * env, so we got 0x110000.
 493  */
 494 #define CONFIG_SYS_FMAN_FW_ADDR 0x110000
 495 #elif defined(CONFIG_SDCARD)
 496 /*
 497  * PBL SD boot image should stored at 0x1000(8 blocks), the size of the image is
 498  * about 1MB (2048 blocks), Env is stored after the image, and the env size is
 499  * 0x2000 (16 blocks), 8 + 2048 + 16 = 2072, enlarge it to 2080.
 500  */
 501 #define CONFIG_SYS_FMAN_FW_ADDR (512 * 0x820)
 502 #elif defined(CONFIG_SRIO_PCIE_BOOT_SLAVE)
 503 /*
 504  * Slave has no ucode locally, it can fetch this from remote. When implementing
 505  * in two corenet boards, slave's ucode could be stored in master's memory
 506  * space, the address can be mapped from slave TLB->slave LAW->
 507  * slave SRIO or PCIE outbound window->master inbound window->
 508  * master LAW->the ucode address in master's memory space.
 509  */
 510 #define CONFIG_SYS_FMAN_FW_ADDR 0xFFE00000
 511 #else
 512 #define CONFIG_SYS_FMAN_FW_ADDR 0xEFF00000
 513 #endif
 514 #define CONFIG_SYS_QE_FMAN_FW_LENGTH    0x10000
 515 #define CONFIG_SYS_FDT_PAD              (0x3000 + CONFIG_SYS_QE_FMAN_FW_LENGTH)
 516 #endif /* CONFIG_NOBQFMAN */
 517
 518 #ifdef CONFIG_SYS_DPAA_FMAN
 519 #define RGMII_PHY1_ADDR 0x1
 520 #define RGMII_PHY2_ADDR 0x2
 521 #define FM1_10GEC1_PHY_ADDR       0x3
 522 #define SGMII_CARD_PORT1_PHY_ADDR 0x1C
 523 #define SGMII_CARD_PORT2_PHY_ADDR 0x1D
 524 #define SGMII_CARD_PORT3_PHY_ADDR 0x1E
 525 #define SGMII_CARD_PORT4_PHY_ADDR 0x1F
 526 #endif
 527
 528 #ifdef CONFIG_FMAN_ENET
 529 #define CONFIG_ETHPRIME         "FM1@DTSEC3"
 530 #endif
 531
 532 /*
 533  * SATA
 534  */
 535 #ifdef CONFIG_FSL_SATA_V2
 536 #define CONFIG_SYS_SATA_MAX_DEVICE      2
 537 #define CONFIG_SATA1
 538 #define CONFIG_SYS_SATA1                CONFIG_SYS_MPC85xx_SATA1_ADDR
 539 #define CONFIG_SYS_SATA1_FLAGS          FLAGS_DMA
 540 #define CONFIG_SATA2
 541 #define CONFIG_SYS_SATA2                CONFIG_SYS_MPC85xx_SATA2_ADDR
 542 #define CONFIG_SYS_SATA2_FLAGS          FLAGS_DMA
 543 #define CONFIG_LBA48
 544 #endif
 545
 546 /*
 547  * USB
 548  */
 549 #ifdef CONFIG_USB_EHCI_HCD
 550 #define CONFIG_USB_EHCI_FSL
 551 #define CONFIG_EHCI_HCD_INIT_AFTER_RESET
 552 #define CONFIG_HAS_FSL_DR_USB
 553 #endif
 554
 555 /*
 556  * SDHC
 557  */
 558 #ifdef CONFIG_MMC
 559 #define CONFIG_SYS_FSL_ESDHC_ADDR       CONFIG_SYS_MPC85xx_ESDHC_ADDR
 560 #define CONFIG_SYS_FSL_ESDHC_BROKEN_TIMEOUT
 561 #endif
 562
 563 /*
 564  * Dynamic MTD Partition support with mtdparts
 565  */
 566
 567 /*
 568  * Environment
 569  */
 570 #define CONFIG_LOADS_ECHO       /* echo on for serial download */
 571 #define CONFIG_SYS_LOADS_BAUD_CHANGE    /* allow baudrate change */
 572
 573 /*
 574  * Miscellaneous configurable options
 575  */
 576
 577 /*
 578  * For booting Linux, the board info and command line data
 579  * have to be in the first 64 MB of memory, since this is
 580  * the maximum mapped by the Linux kernel during initialization.
 581  */
 582 #define CONFIG_SYS_BOOTMAPSZ    (64 << 20)      /* Initial map for Linux*/
 583 #define CONFIG_SYS_BOOTM_LEN    (64 << 20)      /* Increase max gunzip size */
 584
 585 /*
 586  * Environment Configuration
 587  */
 588 #define CONFIG_ROOTPATH  "/opt/nfsroot"
 589 #define CONFIG_BOOTFILE  "uImage"
 590 #define CONFIG_UBOOTPATH "u-boot.bin"   /* U-Boot image on TFTP server */
 591
 592 #define __USB_PHY_TYPE          utmi
 593
 594 #define CONFIG_EXTRA_ENV_SETTINGS                               \
 595         "hwconfig=fsl_ddr:"                                     \
 596         "ctlr_intlv=" __stringify(CTRL_INTLV_PREFERED) ","      \
 597         "bank_intlv=auto;"                                      \
 598         "usb1:dr_mode=host,phy_type=" __stringify(__USB_PHY_TYPE) "\0"\
 599         "netdev=eth0\0"                                         \
 600         "uboot=" __stringify(CONFIG_UBOOTPATH) "\0"             \
 601         "ubootaddr=" __stringify(CONFIG_SYS_TEXT_BASE) "\0"     \
 602         "tftpflash=tftpboot $loadaddr $uboot && "               \
 603         "protect off $ubootaddr +$filesize && "                 \
 604         "erase $ubootaddr +$filesize && "                       \
 605         "cp.b $loadaddr $ubootaddr $filesize && "               \
 606         "protect on $ubootaddr +$filesize && "                  \
 607         "cmp.b $loadaddr $ubootaddr $filesize\0"                \
 608         "consoledev=ttyS0\0"                                    \
 609         "ramdiskaddr=2000000\0"                                 \
 610         "ramdiskfile=t2080qds/ramdisk.uboot\0"                  \
 611         "fdtaddr=1e00000\0"                                     \
 612         "fdtfile=t2080qds/t2080qds.dtb\0"                       \
 613         "bdev=sda3\0"
 614
 615 /*
 616  * For emulation this causes u-boot to jump to the start of the
 617  * proof point app code automatically
 618  */
 619 #define PROOF_POINTS                            \
 620         "setenv bootargs root=/dev/$bdev rw "           \
 621         "console=$consoledev,$baudrate $othbootargs;"   \
 622         "cpu 1 release 0x29000000 - - -;"               \
 623         "cpu 2 release 0x29000000 - - -;"               \
 624         "cpu 3 release 0x29000000 - - -;"               \
 625         "cpu 4 release 0x29000000 - - -;"               \
 626         "cpu 5 release 0x29000000 - - -;"               \
 627         "cpu 6 release 0x29000000 - - -;"               \
 628         "cpu 7 release 0x29000000 - - -;"               \
 629         "go 0x29000000"
 630
 631 #define HVBOOT                          \
 632         "setenv bootargs config-addr=0x60000000; "      \
 633         "bootm 0x01000000 - 0x00f00000"
 634
 635 #define ALU                             \
 636         "setenv bootargs root=/dev/$bdev rw "           \
 637         "console=$consoledev,$baudrate $othbootargs;"   \
 638         "cpu 1 release 0x01000000 - - -;"               \
 639         "cpu 2 release 0x01000000 - - -;"               \
 640         "cpu 3 release 0x01000000 - - -;"               \
 641         "cpu 4 release 0x01000000 - - -;"               \
 642         "cpu 5 release 0x01000000 - - -;"               \
 643         "cpu 6 release 0x01000000 - - -;"               \
 644         "cpu 7 release 0x01000000 - - -;"               \
 645         "go 0x01000000"
 646
 647 #define LINUXBOOTCOMMAND                                \
 648         "setenv bootargs root=/dev/ram rw "             \
 649         "console=$consoledev,$baudrate $othbootargs;"   \
 650         "setenv ramdiskaddr 0x02000000;"                \
 651         "setenv fdtaddr 0x00c00000;"                    \
 652         "setenv loadaddr 0x1000000;"                    \
 653         "bootm $loadaddr $ramdiskaddr $fdtaddr"
 654
 655 #define HDBOOT                                  \
 656         "setenv bootargs root=/dev/$bdev rw "           \
 657         "console=$consoledev,$baudrate $othbootargs;"   \
 658         "tftp $loadaddr $bootfile;"                     \
 659         "tftp $fdtaddr $fdtfile;"                       \
 660         "bootm $loadaddr - $fdtaddr"
 661
 662 #define NFSBOOTCOMMAND                  \
 663         "setenv bootargs root=/dev/nfs rw "     \
 664         "nfsroot=$serverip:$rootpath "          \
 665         "ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:$netdev:off " \
 666         "console=$consoledev,$baudrate $othbootargs;"   \
 667         "tftp $loadaddr $bootfile;"             \
 668         "tftp $fdtaddr $fdtfile;"               \
 669         "bootm $loadaddr - $fdtaddr"
 670
 671 #define RAMBOOTCOMMAND                          \
 672         "setenv bootargs root=/dev/ram rw "             \
 673         "console=$consoledev,$baudrate $othbootargs;"   \
 674         "tftp $ramdiskaddr $ramdiskfile;"               \
 675         "tftp $loadaddr $bootfile;"                     \
 676         "tftp $fdtaddr $fdtfile;"                       \
 677         "bootm $loadaddr $ramdiskaddr $fdtaddr"
 678
 679 #define CONFIG_BOOTCOMMAND              LINUXBOOTCOMMAND
 680
 681 #include <asm/fsl_secure_boot.h>
 682
 683 #endif  /* __T208xQDS_H */