include/configs/MPC837XERDB.h

   1 /* SPDX-License-Identifier: GPL-2.0+ */
   2 /*
   3  * Copyright (C) 2007 Freescale Semiconductor, Inc.
   4  * Kevin Lam <kevin.lam@freescale.com>
   5  * Joe D'Abbraccio <joe.d'abbraccio@freescale.com>
   6  */
   7
   8 #ifndef __CONFIG_H
   9 #define __CONFIG_H
  10
  11 /*
  12  * High Level Configuration Options
  13  */
  14 #define CONFIG_E300             1 /* E300 family */
  15
  16 #define CONFIG_HWCONFIG
  17
  18 /*
  19  * On-board devices
  20  */
  21 #define CONFIG_VSC7385_ENET
  22
  23 /* System performance - define the value i.e. CONFIG_SYS_XXX
  24 */
  25
  26 /* Arbiter Configuration Register */
  27 #define CONFIG_SYS_ACR_PIPE_DEP 3       /* Arbiter pipeline depth (0-3) */
  28 #define CONFIG_SYS_ACR_RPTCNT   3       /* Arbiter repeat count (0-7) */
  29
  30 /* System Priority Control Regsiter */
  31 #define CONFIG_SYS_SPCR_TSECEP  3       /* eTSEC1&2 emergency priority (0-3) */
  32
  33 /* System Clock Configuration Register */
  34 #define CONFIG_SYS_SCCR_TSEC1CM 1               /* eTSEC1 clock mode (0-3) */
  35 #define CONFIG_SYS_SCCR_TSEC2CM 1               /* eTSEC2 clock mode (0-3) */
  36 #define CONFIG_SYS_SCCR_SATACM  SCCR_SATACM_2   /* SATA1-4 clock mode (0-3) */
  37
  38 /*
  39  * System IO Config
  40  */
  41 #define CONFIG_SYS_SICRH                0x08200000
  42 #define CONFIG_SYS_SICRL                0x00000000
  43
  44 /*
  45  * Output Buffer Impedance
  46  */
  47 #define CONFIG_SYS_OBIR         0x30100000
  48
  49 /*
  50  * IMMR new address
  51  */
  52 #define CONFIG_SYS_IMMR         0xE0000000
  53
  54 /*
  55  * Device configurations
  56  */
  57
  58 /* Vitesse 7385 */
  59
  60 #ifdef CONFIG_VSC7385_ENET
  61
  62 #define CONFIG_TSEC2
  63
  64 /* The flash address and size of the VSC7385 firmware image */
  65 #define CONFIG_VSC7385_IMAGE            0xFE7FE000
  66 #define CONFIG_VSC7385_IMAGE_SIZE       8192
  67
  68 #endif
  69
  70 /*
  71  * DDR Setup
  72  */
  73 #define CONFIG_SYS_DDR_BASE             0x00000000 /* DDR is system memory */
  74 #define CONFIG_SYS_SDRAM_BASE           CONFIG_SYS_DDR_BASE
  75 #define CONFIG_SYS_DDR_SDRAM_BASE       CONFIG_SYS_DDR_BASE
  76 #define CONFIG_SYS_DDR_SDRAM_CLK_CNTL   0x03000000
  77 #define CONFIG_SYS_83XX_DDR_USES_CS0
  78
  79 #define CONFIG_SYS_DDRCDR_VALUE (DDRCDR_DHC_EN | DDRCDR_ODT | DDRCDR_Q_DRN)
  80
  81 #undef CONFIG_DDR_ECC           /* support DDR ECC function */
  82 #undef CONFIG_DDR_ECC_CMD       /* Use DDR ECC user commands */
  83
  84 #undef CONFIG_NEVER_ASSERT_ODT_TO_CPU   /* Never assert ODT to internal IOs */
  85
  86 /*
  87  * Manually set up DDR parameters
  88  */
  89 #define CONFIG_SYS_DDR_SIZE             256             /* MB */
  90 #define CONFIG_SYS_DDR_CS0_BNDS         0x0000000f
  91 #define CONFIG_SYS_DDR_CS0_CONFIG       (CSCONFIG_EN \
  92                                         | CSCONFIG_ODT_WR_ONLY_CURRENT \
  93                                         | CSCONFIG_ROW_BIT_13 \
  94                                         | CSCONFIG_COL_BIT_10)
  95
  96 #define CONFIG_SYS_DDR_TIMING_3 0x00000000
  97 #define CONFIG_SYS_DDR_TIMING_0 ((0 << TIMING_CFG0_RWT_SHIFT) \
  98                                 | (0 << TIMING_CFG0_WRT_SHIFT) \
  99                                 | (0 << TIMING_CFG0_RRT_SHIFT) \
 100                                 | (0 << TIMING_CFG0_WWT_SHIFT) \
 101                                 | (2 << TIMING_CFG0_ACT_PD_EXIT_SHIFT) \
 102                                 | (6 << TIMING_CFG0_PRE_PD_EXIT_SHIFT) \
 103                                 | (8 << TIMING_CFG0_ODT_PD_EXIT_SHIFT) \
 104                                 | (2 << TIMING_CFG0_MRS_CYC_SHIFT))
 105                                 /* 0x00260802 */ /* DDR400 */
 106 #define CONFIG_SYS_DDR_TIMING_1 ((3 << TIMING_CFG1_PRETOACT_SHIFT) \
 107                                 | (9 << TIMING_CFG1_ACTTOPRE_SHIFT) \
 108                                 | (3 << TIMING_CFG1_ACTTORW_SHIFT) \
 109                                 | (7 << TIMING_CFG1_CASLAT_SHIFT) \
 110                                 | (13 << TIMING_CFG1_REFREC_SHIFT) \
 111                                 | (3 << TIMING_CFG1_WRREC_SHIFT) \
 112                                 | (2 << TIMING_CFG1_ACTTOACT_SHIFT) \
 113                                 | (2 << TIMING_CFG1_WRTORD_SHIFT))
 114                                 /* 0x3937d322 */
 115 #define CONFIG_SYS_DDR_TIMING_2 ((0 << TIMING_CFG2_ADD_LAT_SHIFT) \
 116                                 | (5 << TIMING_CFG2_CPO_SHIFT) \
 117                                 | (3 << TIMING_CFG2_WR_LAT_DELAY_SHIFT) \
 118                                 | (2 << TIMING_CFG2_RD_TO_PRE_SHIFT) \
 119                                 | (3 << TIMING_CFG2_WR_DATA_DELAY_SHIFT) \
 120                                 | (3 << TIMING_CFG2_CKE_PLS_SHIFT) \
 121                                 | (8 << TIMING_CFG2_FOUR_ACT_SHIFT))
 122                                 /* 0x02984cc8 */
 123
 124 #define CONFIG_SYS_DDR_INTERVAL ((1024 << SDRAM_INTERVAL_REFINT_SHIFT) \
 125                                 | (0 << SDRAM_INTERVAL_BSTOPRE_SHIFT))
 126                                 /* 0x06090100 */
 127
 128 #if defined(CONFIG_DDR_2T_TIMING)
 129 #define CONFIG_SYS_DDR_SDRAM_CFG        (SDRAM_CFG_SREN \
 130                                         | SDRAM_CFG_SDRAM_TYPE_DDR2 \
 131                                         | SDRAM_CFG_32_BE \
 132                                         | SDRAM_CFG_2T_EN)
 133                                         /* 0x43088000 */
 134 #else
 135 #define CONFIG_SYS_DDR_SDRAM_CFG        (SDRAM_CFG_SREN \
 136                                         | SDRAM_CFG_SDRAM_TYPE_DDR2)
 137                                         /* 0x43000000 */
 138 #endif
 139 #define CONFIG_SYS_DDR_SDRAM_CFG2       0x00001000 /* 1 posted refresh */
 140 #define CONFIG_SYS_DDR_MODE             ((0x0406 << SDRAM_MODE_ESD_SHIFT) \
 141                                         | (0x0442 << SDRAM_MODE_SD_SHIFT))
 142                                         /* 0x04400442 */ /* DDR400 */
 143 #define CONFIG_SYS_DDR_MODE2            0x00000000
 144
 145 /*
 146  * Memory test
 147  */
 148 #undef CONFIG_SYS_DRAM_TEST             /* memory test, takes time */
 149 #define CONFIG_SYS_MEMTEST_START        0x00040000 /* memtest region */
 150 #define CONFIG_SYS_MEMTEST_END          0x0ef70010
 151
 152 /*
 153  * The reserved memory
 154  */
 155 #define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE /* start of monitor */
 156
 157 #if (CONFIG_SYS_MONITOR_BASE < CONFIG_SYS_FLASH_BASE)
 158 #define CONFIG_SYS_RAMBOOT
 159 #else
 160 #undef  CONFIG_SYS_RAMBOOT
 161 #endif
 162
 163 #define CONFIG_SYS_MONITOR_LEN  (512 * 1024) /* Reserve 512 kB for Mon */
 164 #define CONFIG_SYS_MALLOC_LEN   (512 * 1024) /* Reserved for malloc */
 165
 166 /*
 167  * Initial RAM Base Address Setup
 168  */
 169 #define CONFIG_SYS_INIT_RAM_LOCK        1
 170 #define CONFIG_SYS_INIT_RAM_ADDR        0xE6000000 /* Initial RAM address */
 171 #define CONFIG_SYS_INIT_RAM_SIZE        0x1000 /* Size of used area in RAM */
 172 #define CONFIG_SYS_GBL_DATA_OFFSET      \
 173                         (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
 174
 175 /*
 176  * Local Bus Configuration & Clock Setup
 177  */
 178 #define CONFIG_SYS_LCRR_DBYP    LCRR_DBYP
 179 #define CONFIG_SYS_LCRR_CLKDIV  LCRR_CLKDIV_8
 180 #define CONFIG_SYS_LBC_LBCR             0x00000000
 181 #define CONFIG_FSL_ELBC         1
 182
 183 /*
 184  * FLASH on the Local Bus
 185  */
 186 #define CONFIG_SYS_FLASH_BASE           0xFE000000 /* FLASH base address */
 187 #define CONFIG_SYS_FLASH_SIZE           8 /* max FLASH size is 32M */
 188
 189 #define CONFIG_SYS_FLASH_EMPTY_INFO             /* display empty sectors */
 190
 191 #define CONFIG_SYS_BR0_PRELIM   (CONFIG_SYS_FLASH_BASE \
 192                                 | BR_PS_16      /* 16 bit port */ \
 193                                 | BR_MS_GPCM    /* MSEL = GPCM */ \
 194                                 | BR_V)         /* valid */
 195 #define CONFIG_SYS_OR0_PRELIM   (OR_AM_8MB \
 196                                 | OR_GPCM_XACS \
 197                                 | OR_GPCM_SCY_9 \
 198                                 | OR_GPCM_EHTR_SET \
 199                                 | OR_GPCM_EAD)
 200                                 /* 0xFF800191 */
 201
 202 #define CONFIG_SYS_MAX_FLASH_BANKS      1 /* number of banks */
 203 #define CONFIG_SYS_MAX_FLASH_SECT       256 /* max sectors per device */
 204
 205 #undef  CONFIG_SYS_FLASH_CHECKSUM
 206 #define CONFIG_SYS_FLASH_ERASE_TOUT     60000   /* Flash Erase Timeout (ms) */
 207 #define CONFIG_SYS_FLASH_WRITE_TOUT     500     /* Flash Write Timeout (ms) */
 208
 209 /*
 210  * NAND Flash on the Local Bus
 211  */
 212 #define CONFIG_SYS_NAND_BASE    0xE0600000
 213 #define CONFIG_SYS_BR1_PRELIM   (CONFIG_SYS_NAND_BASE \
 214                                 | BR_DECC_CHK_GEN       /* Use HW ECC */ \
 215                                 | BR_PS_8               /* 8 bit port */ \
 216                                 | BR_MS_FCM             /* MSEL = FCM */ \
 217                                 | BR_V)                 /* valid */
 218 #define CONFIG_SYS_OR1_PRELIM   (OR_AM_32KB \
 219                                 | OR_FCM_CSCT \
 220                                 | OR_FCM_CST \
 221                                 | OR_FCM_CHT \
 222                                 | OR_FCM_SCY_1 \
 223                                 | OR_FCM_TRLX \
 224                                 | OR_FCM_EHTR)
 225 /* Vitesse 7385 */
 226
 227 #define CONFIG_SYS_VSC7385_BASE 0xF0000000
 228
 229 #ifdef CONFIG_VSC7385_ENET
 230
 231 #define CONFIG_SYS_BR2_PRELIM           (CONFIG_SYS_VSC7385_BASE \
 232                                         | BR_PS_8 \
 233                                         | BR_MS_GPCM \
 234                                         | BR_V)
 235                                         /* 0xF0000801 */
 236 #define CONFIG_SYS_OR2_PRELIM           (OR_AM_128KB \
 237                                         | OR_GPCM_CSNT \
 238                                         | OR_GPCM_XACS \
 239                                         | OR_GPCM_SCY_15 \
 240                                         | OR_GPCM_SETA \
 241                                         | OR_GPCM_TRLX_SET \
 242                                         | OR_GPCM_EHTR_SET \
 243                                         | OR_GPCM_EAD)
 244                                         /* 0xfffe09ff */
 245 #endif
 246
 247 /*
 248  * Serial Port
 249  */
 250 #define CONFIG_SYS_NS16550_SERIAL
 251 #define CONFIG_SYS_NS16550_REG_SIZE     1
 252 #define CONFIG_SYS_NS16550_CLK          get_bus_freq(0)
 253
 254 #define CONFIG_SYS_BAUDRATE_TABLE \
 255                 {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 115200}
 256
 257 #define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_IMMR+0x4500)
 258 #define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_IMMR+0x4600)
 259
 260 /* SERDES */
 261 #define CONFIG_FSL_SERDES
 262 #define CONFIG_FSL_SERDES1      0xe3000
 263 #define CONFIG_FSL_SERDES2      0xe3100
 264
 265 /* I2C */
 266 #define CONFIG_SYS_I2C
 267 #define CONFIG_SYS_I2C_FSL
 268 #define CONFIG_SYS_FSL_I2C_SPEED        400000
 269 #define CONFIG_SYS_FSL_I2C_SLAVE        0x7F
 270 #define CONFIG_SYS_FSL_I2C_OFFSET       0x3000
 271 #define CONFIG_SYS_I2C_NOPROBES         { {0, 0x51} }
 272
 273 /*
 274  * Config on-board RTC
 275  */
 276 #define CONFIG_RTC_DS1374       /* use ds1374 rtc via i2c */
 277 #define CONFIG_SYS_I2C_RTC_ADDR 0x68 /* at address 0x68 */
 278
 279 /*
 280  * General PCI
 281  * Addresses are mapped 1-1.
 282  */
 283 #define CONFIG_SYS_PCI_MEM_BASE         0x80000000
 284 #define CONFIG_SYS_PCI_MEM_PHYS         CONFIG_SYS_PCI_MEM_BASE
 285 #define CONFIG_SYS_PCI_MEM_SIZE         0x10000000 /* 256M */
 286 #define CONFIG_SYS_PCI_MMIO_BASE        0x90000000
 287 #define CONFIG_SYS_PCI_MMIO_PHYS        CONFIG_SYS_PCI_MMIO_BASE
 288 #define CONFIG_SYS_PCI_MMIO_SIZE        0x10000000 /* 256M */
 289 #define CONFIG_SYS_PCI_IO_BASE          0x00000000
 290 #define CONFIG_SYS_PCI_IO_PHYS          0xE0300000
 291 #define CONFIG_SYS_PCI_IO_SIZE          0x100000 /* 1M */
 292
 293 #define CONFIG_SYS_PCI_SLV_MEM_LOCAL    CONFIG_SYS_SDRAM_BASE
 294 #define CONFIG_SYS_PCI_SLV_MEM_BUS      0x00000000
 295 #define CONFIG_SYS_PCI_SLV_MEM_SIZE     0x80000000
 296
 297 #define CONFIG_SYS_PCIE1_BASE           0xA0000000
 298 #define CONFIG_SYS_PCIE1_CFG_BASE       0xA0000000
 299 #define CONFIG_SYS_PCIE1_CFG_SIZE       0x08000000
 300 #define CONFIG_SYS_PCIE1_MEM_BASE       0xA8000000
 301 #define CONFIG_SYS_PCIE1_MEM_PHYS       0xA8000000
 302 #define CONFIG_SYS_PCIE1_MEM_SIZE       0x10000000
 303 #define CONFIG_SYS_PCIE1_IO_BASE        0x00000000
 304 #define CONFIG_SYS_PCIE1_IO_PHYS        0xB8000000
 305 #define CONFIG_SYS_PCIE1_IO_SIZE        0x00800000
 306
 307 #define CONFIG_SYS_PCIE2_BASE           0xC0000000
 308 #define CONFIG_SYS_PCIE2_CFG_BASE       0xC0000000
 309 #define CONFIG_SYS_PCIE2_CFG_SIZE       0x08000000
 310 #define CONFIG_SYS_PCIE2_MEM_BASE       0xC8000000
 311 #define CONFIG_SYS_PCIE2_MEM_PHYS       0xC8000000
 312 #define CONFIG_SYS_PCIE2_MEM_SIZE       0x10000000
 313 #define CONFIG_SYS_PCIE2_IO_BASE        0x00000000
 314 #define CONFIG_SYS_PCIE2_IO_PHYS        0xD8000000
 315 #define CONFIG_SYS_PCIE2_IO_SIZE        0x00800000
 316
 317 #ifdef CONFIG_PCI
 318 #define CONFIG_PCI_INDIRECT_BRIDGE
 319
 320 #undef CONFIG_PCI_SCAN_SHOW     /* show pci devices on startup */
 321 #define CONFIG_SYS_PCI_SUBSYS_VENDORID 0x1957   /* Freescale */
 322 #endif  /* CONFIG_PCI */
 323
 324 /*
 325  * TSEC
 326  */
 327 #ifdef CONFIG_TSEC_ENET
 328
 329 #define CONFIG_GMII                     /* MII PHY management */
 330
 331 #define CONFIG_TSEC1
 332
 333 #ifdef CONFIG_TSEC1
 334 #define CONFIG_HAS_ETH0
 335 #define CONFIG_TSEC1_NAME               "TSEC0"
 336 #define CONFIG_SYS_TSEC1_OFFSET         0x24000
 337 #define TSEC1_PHY_ADDR                  2
 338 #define TSEC1_FLAGS                     (TSEC_GIGABIT | TSEC_REDUCED)
 339 #define TSEC1_PHYIDX                    0
 340 #endif
 341
 342 #ifdef CONFIG_TSEC2
 343 #define CONFIG_HAS_ETH1
 344 #define CONFIG_TSEC2_NAME               "TSEC1"
 345 #define CONFIG_SYS_TSEC2_OFFSET         0x25000
 346 #define TSEC2_PHY_ADDR                  0x1c
 347 #define TSEC2_FLAGS                     (TSEC_GIGABIT | TSEC_REDUCED)
 348 #define TSEC2_PHYIDX                    0
 349 #endif
 350
 351 /* Options are: TSEC[0-1] */
 352 #define CONFIG_ETHPRIME                 "TSEC0"
 353
 354 #endif
 355
 356 /*
 357  * SATA
 358  */
 359 #define CONFIG_SYS_SATA_MAX_DEVICE      2
 360 #define CONFIG_SATA1
 361 #define CONFIG_SYS_SATA1_OFFSET 0x18000
 362 #define CONFIG_SYS_SATA1        (CONFIG_SYS_IMMR + CONFIG_SYS_SATA1_OFFSET)
 363 #define CONFIG_SYS_SATA1_FLAGS  FLAGS_DMA
 364 #define CONFIG_SATA2
 365 #define CONFIG_SYS_SATA2_OFFSET 0x19000
 366 #define CONFIG_SYS_SATA2        (CONFIG_SYS_IMMR + CONFIG_SYS_SATA2_OFFSET)
 367 #define CONFIG_SYS_SATA2_FLAGS  FLAGS_DMA
 368
 369 #ifdef CONFIG_FSL_SATA
 370 #define CONFIG_LBA48
 371 #endif
 372
 373 /*
 374  * Environment
 375  */
 376 #ifndef CONFIG_SYS_RAMBOOT
 377         #define CONFIG_ENV_ADDR         \
 378                         (CONFIG_SYS_MONITOR_BASE+CONFIG_SYS_MONITOR_LEN)
 379         #define CONFIG_ENV_SECT_SIZE    0x10000 /* 64K (one sector) for env */
 380         #define CONFIG_ENV_SIZE         0x4000
 381 #else
 382         #define CONFIG_ENV_ADDR         (CONFIG_SYS_MONITOR_BASE-0x1000)
 383         #define CONFIG_ENV_SIZE         0x2000
 384 #endif
 385
 386 #define CONFIG_LOADS_ECHO       1       /* echo on for serial download */
 387 #define CONFIG_SYS_LOADS_BAUD_CHANGE    1       /* allow baudrate change */
 388
 389 /*
 390  * BOOTP options
 391  */
 392 #define CONFIG_BOOTP_BOOTFILESIZE
 393
 394 /*
 395  * Command line configuration.
 396  */
 397
 398 #undef CONFIG_WATCHDOG          /* watchdog disabled */
 399
 400 #ifdef CONFIG_MMC
 401 #define CONFIG_FSL_ESDHC_PIN_MUX
 402 #define CONFIG_SYS_FSL_ESDHC_ADDR       CONFIG_SYS_MPC83xx_ESDHC_ADDR
 403 #endif
 404
 405 /*
 406  * Miscellaneous configurable options
 407  */
 408 #define CONFIG_SYS_LOAD_ADDR    0x2000000 /* default load address */
 409
 410 /*
 411  * For booting Linux, the board info and command line data
 412  * have to be in the first 256 MB of memory, since this is
 413  * the maximum mapped by the Linux kernel during initialization.
 414  */
 415 #define CONFIG_SYS_BOOTMAPSZ    (256 << 20) /* Initial Memory map for Linux */
 416 #define CONFIG_SYS_BOOTM_LEN    (64 << 20)      /* Increase max gunzip size */
 417
 418 /*
 419  * Core HID Setup
 420  */
 421 #define CONFIG_SYS_HID0_INIT    0x000000000
 422 #define CONFIG_SYS_HID0_FINAL   (HID0_ENABLE_MACHINE_CHECK \
 423                                 | HID0_ENABLE_INSTRUCTION_CACHE)
 424 #define CONFIG_SYS_HID2         HID2_HBE
 425
 426 #if defined(CONFIG_CMD_KGDB)
 427 #define CONFIG_KGDB_BAUDRATE    230400  /* speed of kgdb serial port */
 428 #endif
 429
 430 /*
 431  * Environment Configuration
 432  */
 433 #define CONFIG_ENV_OVERWRITE
 434
 435 #define CONFIG_HAS_FSL_DR_USB
 436 #define CONFIG_USB_EHCI_FSL
 437 #define CONFIG_EHCI_HCD_INIT_AFTER_RESET
 438
 439 #define CONFIG_NETDEV           "eth1"
 440
 441 #define CONFIG_HOSTNAME         "mpc837x_rdb"
 442 #define CONFIG_ROOTPATH         "/nfsroot"
 443 #define CONFIG_RAMDISKFILE      "rootfs.ext2.gz.uboot"
 444 #define CONFIG_BOOTFILE         "uImage"
 445                                 /* U-Boot image on TFTP server */
 446 #define CONFIG_UBOOTPATH        "u-boot.bin"
 447 #define CONFIG_FDTFILE          "mpc8379_rdb.dtb"
 448
 449                                 /* default location for tftp and bootm */
 450 #define CONFIG_LOADADDR         800000
 451
 452 #define CONFIG_EXTRA_ENV_SETTINGS \
 453         "netdev=" CONFIG_NETDEV "\0"                            \
 454         "uboot=" CONFIG_UBOOTPATH "\0"                                  \
 455         "tftpflash=tftp $loadaddr $uboot;"                              \
 456                 "protect off " __stringify(CONFIG_SYS_TEXT_BASE)        \
 457                         " +$filesize; " \
 458                 "erase " __stringify(CONFIG_SYS_TEXT_BASE)              \
 459                         " +$filesize; " \
 460                 "cp.b $loadaddr " __stringify(CONFIG_SYS_TEXT_BASE)     \
 461                         " $filesize; "  \
 462                 "protect on " __stringify(CONFIG_SYS_TEXT_BASE)         \
 463                         " +$filesize; " \
 464                 "cmp.b $loadaddr " __stringify(CONFIG_SYS_TEXT_BASE)    \
 465                         " $filesize\0"  \
 466         "fdtaddr=780000\0"                                              \
 467         "fdtfile=" CONFIG_FDTFILE "\0"                                  \
 468         "ramdiskaddr=1000000\0"                                         \
 469         "ramdiskfile=" CONFIG_RAMDISKFILE "\0"                          \
 470         "console=ttyS0\0"                                               \
 471         "setbootargs=setenv bootargs "                                  \
 472                 "root=$rootdev rw console=$console,$baudrate $othbootargs\0" \
 473         "setipargs=setenv bootargs nfsroot=$serverip:$rootpath "        \
 474                 "ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:"   \
 475                                                         "$netdev:off "  \
 476                 "root=$rootdev rw console=$console,$baudrate $othbootargs\0"
 477
 478 #define CONFIG_NFSBOOTCOMMAND                                           \
 479         "setenv rootdev /dev/nfs;"                                      \
 480         "run setbootargs;"                                              \
 481         "run setipargs;"                                                \
 482         "tftp $loadaddr $bootfile;"                                     \
 483         "tftp $fdtaddr $fdtfile;"                                       \
 484         "bootm $loadaddr - $fdtaddr"
 485
 486 #define CONFIG_RAMBOOTCOMMAND                                           \
 487         "setenv rootdev /dev/ram;"                                      \
 488         "run setbootargs;"                                              \
 489         "tftp $ramdiskaddr $ramdiskfile;"                               \
 490         "tftp $loadaddr $bootfile;"                                     \
 491         "tftp $fdtaddr $fdtfile;"                                       \
 492         "bootm $loadaddr $ramdiskaddr $fdtaddr"
 493
 494 #endif  /* __CONFIG_H */