From: Tom Rini <trini@ti.com>
Date: Fri, 14 Nov 2014 18:53:49 +0000 (-0500)
Subject: Merge branch 'master' of git://www.denx.de/git/u-boot-imx
X-Git-Tag: v2015.01-rc2~79
X-Git-Url: http://review.tizen.org/git/?p=platform%2Fkernel%2Fu-boot.git;a=commitdiff_plain;h=45043cf804763d4cf93fec93d8294e385f87622a;hp=0d485b9095328cdc81b2ee94ff59b988c69b9127

Merge branch 'master' of git://denx.de/git/u-boot-imx
---

diff --git a/arch/arm/Kconfig b/arch/arm/Kconfig
index 3955978..bd073eb 100644
--- a/arch/arm/Kconfig
+++ b/arch/arm/Kconfig
@@ -612,6 +612,7 @@ config TARGET_MX6QSABREAUTO
 config TARGET_MX6SABRESD
 	bool "Support mx6sabresd"
 	select CPU_V7
+	select SUPPORT_SPL
 
 config TARGET_MX6SLEVK
 	bool "Support mx6slevk"
@@ -635,6 +636,9 @@ config TARGET_KOSAGI_NOVENA
 	select CPU_V7
 	select SUPPORT_SPL
 
+config TARGET_TBS2910
+	bool "Support tbs2910"
+
 config TARGET_TQMA6
 	bool "TQ Systems TQMa6 board"
 	select CPU_V7
@@ -936,6 +940,7 @@ source "board/sunxi/Kconfig"
 source "board/syteco/jadecpu/Kconfig"
 source "board/syteco/zmx25/Kconfig"
 source "board/taskit/stamp9g20/Kconfig"
+source "board/tbs/tbs2910/Kconfig"
 source "board/ti/am335x/Kconfig"
 source "board/ti/am43xx/Kconfig"
 source "board/ti/ti814x/Kconfig"
diff --git a/arch/arm/cpu/armv7/mx6/soc.c b/arch/arm/cpu/armv7/mx6/soc.c
index affbf7f..5fd2a63 100644
--- a/arch/arm/cpu/armv7/mx6/soc.c
+++ b/arch/arm/cpu/armv7/mx6/soc.c
@@ -350,8 +350,8 @@ void boot_mode_apply(unsigned cfg_val)
 /*
  * cfg_val will be used for
  * Boot_cfg4[7:0]:Boot_cfg3[7:0]:Boot_cfg2[7:0]:Boot_cfg1[7:0]
- * After reset, if GPR10[28] is 1, ROM will copy GPR9[25:0]
- * to SBMR1, which will determine the boot device.
+ * After reset, if GPR10[28] is 1, ROM will use GPR9[25:0]
+ * instead of SBMR1 to determine the boot device.
  */
 const struct boot_mode soc_boot_modes[] = {
 	{"normal",	MAKE_CFGVAL(0x00, 0x00, 0x00, 0x00)},
diff --git a/arch/arm/imx-common/spl.c b/arch/arm/imx-common/spl.c
index 9d3c31a..477c38c 100644
--- a/arch/arm/imx-common/spl.c
+++ b/arch/arm/imx-common/spl.c
@@ -14,11 +14,12 @@
 #include <spl.h>
 
 #if defined(CONFIG_MX6)
-/* determine boot device from SRC_SBMR1 register (BOOT_CFG[4:1]) */
+/* determine boot device from SRC_SBMR1 (BOOT_CFG[4:1]) or SRC_GPR9 register */
 u32 spl_boot_device(void)
 {
 	struct src *psrc = (struct src *)SRC_BASE_ADDR;
-	unsigned reg = readl(&psrc->sbmr1);
+	unsigned int gpr10_boot = readl(&psrc->gpr10) & (1 << 28);
+	unsigned reg = gpr10_boot ? readl(&psrc->gpr9) : readl(&psrc->sbmr1);
 
 	/* BOOT_CFG1[7:4] - see IMX6DQRM Table 8-8 */
 	switch ((reg & 0x000000FF) >> 4) {
diff --git a/arch/arm/imx-common/video.c b/arch/arm/imx-common/video.c
index 8651b80..46f8a1e 100644
--- a/arch/arm/imx-common/video.c
+++ b/arch/arm/imx-common/video.c
@@ -11,6 +11,7 @@ int board_video_skip(void)
 	int i;
 	int ret;
 	char const *panel = getenv("panel");
+
 	if (!panel) {
 		for (i = 0; i < display_count; i++) {
 			struct display_info_t const *dev = displays+i;
@@ -31,11 +32,14 @@ int board_video_skip(void)
 				break;
 		}
 	}
+
 	if (i < display_count) {
 		ret = ipuv3_fb_init(&displays[i].mode, 0,
 				    displays[i].pixfmt);
 		if (!ret) {
-			displays[i].enable(displays+i);
+			if (displays[i].enable)
+				displays[i].enable(displays + i);
+
 			printf("Display: %s (%ux%u)\n",
 			       displays[i].mode.name,
 			       displays[i].mode.xres,
diff --git a/board/bachmann/ot1200/ot1200.c b/board/bachmann/ot1200/ot1200.c
index 2ed8cf7..007c1ef 100644
--- a/board/bachmann/ot1200/ot1200.c
+++ b/board/bachmann/ot1200/ot1200.c
@@ -159,8 +159,8 @@ int board_mmc_getcd(struct mmc *mmc)
 		gpio_direction_input(IMX_GPIO_NR(4, 5));
 		ret = gpio_get_value(IMX_GPIO_NR(4, 5));
 	} else {
-		gpio_direction_input(IMX_GPIO_NR(1, 4));
-		ret = !gpio_get_value(IMX_GPIO_NR(1, 4));
+		gpio_direction_input(IMX_GPIO_NR(1, 5));
+		ret = !gpio_get_value(IMX_GPIO_NR(1, 5));
 	}
 
 	return ret;
diff --git a/board/freescale/mx28evk/README b/board/freescale/mx28evk/README
index 958ebc6..f9d6324 100644
--- a/board/freescale/mx28evk/README
+++ b/board/freescale/mx28evk/README
@@ -1,7 +1,7 @@
 FREESCALE MX28EVK
 ==================
 
-Supported hardware: only MX28EVK rev D is supported in U-boot.
+Supported hardware: MX28EVK rev C and D are supported in U-boot.
 
 Files of the MX28EVK port
 --------------------------
diff --git a/board/freescale/mx53loco/mx53loco.c b/board/freescale/mx53loco/mx53loco.c
index b32a97f..7569ded 100644
--- a/board/freescale/mx53loco/mx53loco.c
+++ b/board/freescale/mx53loco/mx53loco.c
@@ -242,6 +242,8 @@ static int power_init(void)
 		if (!p)
 			return -ENODEV;
 
+		setenv("fdt_file", "imx53-qsb.dtb");
+
 		/* Set VDDA to 1.25V */
 		val = DA9052_BUCKCORE_BCOREEN | DA_BUCKCORE_VBCORE_1_250V;
 		ret = pmic_reg_write(p, DA9053_BUCKCORE_REG, val);
@@ -283,6 +285,8 @@ static int power_init(void)
 		if (!p)
 			return -ENODEV;
 
+		setenv("fdt_file", "imx53-qsrb.dtb");
+
 		/* Set VDDGP to 1.25V for 1GHz on SW1 */
 		pmic_reg_read(p, REG_SW_0, &val);
 		val = (val & ~SWx_VOLT_MASK_MC34708) | SWx_1_250V_MC34708;
diff --git a/board/freescale/mx6qsabreauto/mx6qsabreauto.c b/board/freescale/mx6qsabreauto/mx6qsabreauto.c
index 42ae6fa..c35dcaf 100644
--- a/board/freescale/mx6qsabreauto/mx6qsabreauto.c
+++ b/board/freescale/mx6qsabreauto/mx6qsabreauto.c
@@ -46,6 +46,11 @@ DECLARE_GLOBAL_DATA_PTR;
 	PAD_CTL_SPEED_MED | PAD_CTL_DSE_40ohm | PAD_CTL_HYS |	\
 	PAD_CTL_ODE | PAD_CTL_SRE_FAST)
 
+#define GPMI_PAD_CTRL0 (PAD_CTL_PKE | PAD_CTL_PUE | PAD_CTL_PUS_100K_UP)
+#define GPMI_PAD_CTRL1 (PAD_CTL_DSE_40ohm | PAD_CTL_SPEED_MED | \
+			PAD_CTL_SRE_FAST)
+#define GPMI_PAD_CTRL2 (GPMI_PAD_CTRL0 | GPMI_PAD_CTRL1)
+
 #define PC MUX_PAD_CTRL(I2C_PAD_CTRL)
 
 int dram_init(void)
@@ -200,6 +205,63 @@ int board_mmc_init(bd_t *bis)
 }
 #endif
 
+#ifdef CONFIG_NAND_MXS
+static iomux_v3_cfg_t gpmi_pads[] = {
+	MX6_PAD_NANDF_CLE__NAND_CLE		| MUX_PAD_CTRL(GPMI_PAD_CTRL2),
+	MX6_PAD_NANDF_ALE__NAND_ALE		| MUX_PAD_CTRL(GPMI_PAD_CTRL2),
+	MX6_PAD_NANDF_WP_B__NAND_WP_B	| MUX_PAD_CTRL(GPMI_PAD_CTRL2),
+	MX6_PAD_NANDF_RB0__NAND_READY_B	| MUX_PAD_CTRL(GPMI_PAD_CTRL0),
+	MX6_PAD_NANDF_CS0__NAND_CE0_B	| MUX_PAD_CTRL(GPMI_PAD_CTRL2),
+	MX6_PAD_SD4_CMD__NAND_RE_B		| MUX_PAD_CTRL(GPMI_PAD_CTRL2),
+	MX6_PAD_SD4_CLK__NAND_WE_B		| MUX_PAD_CTRL(GPMI_PAD_CTRL2),
+	MX6_PAD_NANDF_D0__NAND_DATA00	| MUX_PAD_CTRL(GPMI_PAD_CTRL2),
+	MX6_PAD_NANDF_D1__NAND_DATA01	| MUX_PAD_CTRL(GPMI_PAD_CTRL2),
+	MX6_PAD_NANDF_D2__NAND_DATA02	| MUX_PAD_CTRL(GPMI_PAD_CTRL2),
+	MX6_PAD_NANDF_D3__NAND_DATA03	| MUX_PAD_CTRL(GPMI_PAD_CTRL2),
+	MX6_PAD_NANDF_D4__NAND_DATA04	| MUX_PAD_CTRL(GPMI_PAD_CTRL2),
+	MX6_PAD_NANDF_D5__NAND_DATA05	| MUX_PAD_CTRL(GPMI_PAD_CTRL2),
+	MX6_PAD_NANDF_D6__NAND_DATA06	| MUX_PAD_CTRL(GPMI_PAD_CTRL2),
+	MX6_PAD_NANDF_D7__NAND_DATA07	| MUX_PAD_CTRL(GPMI_PAD_CTRL2),
+	MX6_PAD_SD4_DAT0__NAND_DQS		| MUX_PAD_CTRL(GPMI_PAD_CTRL1),
+};
+
+static void setup_gpmi_nand(void)
+{
+	struct mxc_ccm_reg *mxc_ccm = (struct mxc_ccm_reg *)CCM_BASE_ADDR;
+
+	/* config gpmi nand iomux */
+	imx_iomux_v3_setup_multiple_pads(gpmi_pads, ARRAY_SIZE(gpmi_pads));
+
+	/* gate ENFC_CLK_ROOT clock first,before clk source switch */
+	clrbits_le32(&mxc_ccm->CCGR2, MXC_CCM_CCGR2_IOMUX_IPT_CLK_IO_MASK);
+	clrbits_le32(&mxc_ccm->CCGR4,
+		MXC_CCM_CCGR4_RAWNAND_U_GPMI_BCH_INPUT_GPMI_IO_MASK);
+
+	/* config gpmi and bch clock to 100 MHz */
+	clrsetbits_le32(&mxc_ccm->cs2cdr,
+			MXC_CCM_CS2CDR_ENFC_CLK_PODF_MASK |
+			MXC_CCM_CS2CDR_ENFC_CLK_PRED_MASK |
+			MXC_CCM_CS2CDR_ENFC_CLK_SEL_MASK,
+			MXC_CCM_CS2CDR_ENFC_CLK_PODF(0) |
+			MXC_CCM_CS2CDR_ENFC_CLK_PRED(3) |
+			MXC_CCM_CS2CDR_ENFC_CLK_SEL(3));
+
+	/* enable ENFC_CLK_ROOT clock */
+	setbits_le32(&mxc_ccm->CCGR2, MXC_CCM_CCGR2_IOMUX_IPT_CLK_IO_MASK);
+
+	/* enable gpmi and bch clock gating */
+	setbits_le32(&mxc_ccm->CCGR4,
+		     MXC_CCM_CCGR4_RAWNAND_U_BCH_INPUT_APB_MASK |
+		     MXC_CCM_CCGR4_RAWNAND_U_GPMI_BCH_INPUT_BCH_MASK |
+		     MXC_CCM_CCGR4_RAWNAND_U_GPMI_BCH_INPUT_GPMI_IO_MASK |
+		     MXC_CCM_CCGR4_RAWNAND_U_GPMI_INPUT_APB_MASK |
+		     MXC_CCM_CCGR4_PL301_MX6QPER1_BCH_OFFSET);
+
+	/* enable apbh clock gating */
+	setbits_le32(&mxc_ccm->CCGR0, MXC_CCM_CCGR0_APBHDMA_MASK);
+}
+#endif
+
 int mx6_rgmii_rework(struct phy_device *phydev)
 {
 	unsigned short val;
@@ -336,6 +398,10 @@ int board_early_init_f(void)
 #ifdef CONFIG_VIDEO_IPUV3
 	setup_display();
 #endif
+
+#ifdef CONFIG_NAND_MXS
+	setup_gpmi_nand();
+#endif
 	return 0;
 }
 
diff --git a/board/freescale/mx6sabresd/mx6sabresd.c b/board/freescale/mx6sabresd/mx6sabresd.c
index 3d81fff..1142e8a 100644
--- a/board/freescale/mx6sabresd/mx6sabresd.c
+++ b/board/freescale/mx6sabresd/mx6sabresd.c
@@ -27,8 +27,12 @@
 #include <i2c.h>
 #include <power/pmic.h>
 #include <power/pfuze100_pmic.h>
+#include <asm/arch/mx6-ddr.h>
+
 DECLARE_GLOBAL_DATA_PTR;
 
+#define BOOT_CFG	0x020D8004
+
 #define UART_PAD_CTRL  (PAD_CTL_PUS_100K_UP |			\
 	PAD_CTL_SPEED_MED | PAD_CTL_DSE_40ohm |			\
 	PAD_CTL_SRE_FAST  | PAD_CTL_HYS)
@@ -55,17 +59,16 @@ DECLARE_GLOBAL_DATA_PTR;
 
 int dram_init(void)
 {
-	gd->ram_size = get_ram_size((void *)PHYS_SDRAM, PHYS_SDRAM_SIZE);
-
+	gd->ram_size = imx_ddr_size();
 	return 0;
 }
 
-iomux_v3_cfg_t const uart1_pads[] = {
+static iomux_v3_cfg_t const uart1_pads[] = {
 	MX6_PAD_CSI0_DAT10__UART1_TX_DATA | MUX_PAD_CTRL(UART_PAD_CTRL),
 	MX6_PAD_CSI0_DAT11__UART1_RX_DATA | MUX_PAD_CTRL(UART_PAD_CTRL),
 };
 
-iomux_v3_cfg_t const enet_pads[] = {
+static iomux_v3_cfg_t const enet_pads[] = {
 	MX6_PAD_ENET_MDIO__ENET_MDIO		| MUX_PAD_CTRL(ENET_PAD_CTRL),
 	MX6_PAD_ENET_MDC__ENET_MDC		| MUX_PAD_CTRL(ENET_PAD_CTRL),
 	MX6_PAD_RGMII_TXC__RGMII_TXC	| MUX_PAD_CTRL(ENET_PAD_CTRL),
@@ -95,7 +98,7 @@ static void setup_iomux_enet(void)
 	gpio_set_value(IMX_GPIO_NR(1, 25), 1);
 }
 
-iomux_v3_cfg_t const usdhc2_pads[] = {
+static iomux_v3_cfg_t const usdhc2_pads[] = {
 	MX6_PAD_SD2_CLK__SD2_CLK	| MUX_PAD_CTRL(USDHC_PAD_CTRL),
 	MX6_PAD_SD2_CMD__SD2_CMD	| MUX_PAD_CTRL(USDHC_PAD_CTRL),
 	MX6_PAD_SD2_DAT0__SD2_DATA0	| MUX_PAD_CTRL(USDHC_PAD_CTRL),
@@ -109,7 +112,7 @@ iomux_v3_cfg_t const usdhc2_pads[] = {
 	MX6_PAD_NANDF_D2__GPIO2_IO02	| MUX_PAD_CTRL(NO_PAD_CTRL), /* CD */
 };
 
-iomux_v3_cfg_t const usdhc3_pads[] = {
+static iomux_v3_cfg_t const usdhc3_pads[] = {
 	MX6_PAD_SD3_CLK__SD3_CLK   | MUX_PAD_CTRL(USDHC_PAD_CTRL),
 	MX6_PAD_SD3_CMD__SD3_CMD   | MUX_PAD_CTRL(USDHC_PAD_CTRL),
 	MX6_PAD_SD3_DAT0__SD3_DATA0 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
@@ -123,7 +126,7 @@ iomux_v3_cfg_t const usdhc3_pads[] = {
 	MX6_PAD_NANDF_D0__GPIO2_IO00    | MUX_PAD_CTRL(NO_PAD_CTRL), /* CD */
 };
 
-iomux_v3_cfg_t const usdhc4_pads[] = {
+static iomux_v3_cfg_t const usdhc4_pads[] = {
 	MX6_PAD_SD4_CLK__SD4_CLK   | MUX_PAD_CTRL(USDHC_PAD_CTRL),
 	MX6_PAD_SD4_CMD__SD4_CMD   | MUX_PAD_CTRL(USDHC_PAD_CTRL),
 	MX6_PAD_SD4_DAT0__SD4_DATA0 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
@@ -136,7 +139,7 @@ iomux_v3_cfg_t const usdhc4_pads[] = {
 	MX6_PAD_SD4_DAT7__SD4_DATA7 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
 };
 
-iomux_v3_cfg_t const ecspi1_pads[] = {
+static iomux_v3_cfg_t const ecspi1_pads[] = {
 	MX6_PAD_KEY_COL0__ECSPI1_SCLK | MUX_PAD_CTRL(SPI_PAD_CTRL),
 	MX6_PAD_KEY_COL1__ECSPI1_MISO | MUX_PAD_CTRL(SPI_PAD_CTRL),
 	MX6_PAD_KEY_ROW0__ECSPI1_MOSI | MUX_PAD_CTRL(SPI_PAD_CTRL),
@@ -253,7 +256,8 @@ int board_mmc_getcd(struct mmc *mmc)
 
 int board_mmc_init(bd_t *bis)
 {
-	s32 status = 0;
+#ifndef CONFIG_SPL_BUILD
+	int ret;
 	int i;
 
 	/*
@@ -286,13 +290,52 @@ int board_mmc_init(bd_t *bis)
 			printf("Warning: you configured more USDHC controllers"
 			       "(%d) then supported by the board (%d)\n",
 			       i + 1, CONFIG_SYS_FSL_USDHC_NUM);
-			return status;
+			return -EINVAL;
 		}
 
-		status |= fsl_esdhc_initialize(bis, &usdhc_cfg[i]);
+		ret = fsl_esdhc_initialize(bis, &usdhc_cfg[i]);
+		if (ret)
+			return ret;
 	}
 
-	return status;
+	return 0;
+#else
+	unsigned reg = readl(BOOT_CFG) >> 11;
+	/*
+	 * Upon reading BOOT_CFG register the following map is done:
+	 * Bit 11 and 12 of BOOT_CFG register can determine the current
+	 * mmc port
+	 * 0x1                  SD1
+	 * 0x2                  SD2
+	 * 0x3                  SD4
+	 */
+
+	switch (reg & 0x3) {
+	case 0x1:
+		imx_iomux_v3_setup_multiple_pads(
+			usdhc2_pads, ARRAY_SIZE(usdhc2_pads));
+		usdhc_cfg[0].esdhc_base = USDHC2_BASE_ADDR;
+		usdhc_cfg[0].sdhc_clk = mxc_get_clock(MXC_ESDHC2_CLK);
+		gd->arch.sdhc_clk = usdhc_cfg[0].sdhc_clk;
+		break;
+	case 0x2:
+		imx_iomux_v3_setup_multiple_pads(
+			usdhc3_pads, ARRAY_SIZE(usdhc3_pads));
+		usdhc_cfg[0].esdhc_base = USDHC3_BASE_ADDR;
+		usdhc_cfg[0].sdhc_clk = mxc_get_clock(MXC_ESDHC3_CLK);
+		gd->arch.sdhc_clk = usdhc_cfg[0].sdhc_clk;
+		break;
+	case 0x3:
+		imx_iomux_v3_setup_multiple_pads(
+			usdhc4_pads, ARRAY_SIZE(usdhc4_pads));
+		usdhc_cfg[0].esdhc_base = USDHC4_BASE_ADDR;
+		usdhc_cfg[0].sdhc_clk = mxc_get_clock(MXC_ESDHC4_CLK);
+		gd->arch.sdhc_clk = usdhc_cfg[0].sdhc_clk;
+		break;
+	}
+
+	return fsl_esdhc_initialize(bis, &usdhc_cfg[0]);
+#endif
 }
 #endif
 
@@ -607,3 +650,144 @@ int checkboard(void)
 	puts("Board: MX6-SabreSD\n");
 	return 0;
 }
+
+#ifdef CONFIG_SPL_BUILD
+#include <spl.h>
+#include <libfdt.h>
+
+const struct mx6dq_iomux_ddr_regs mx6_ddr_ioregs = {
+	.dram_sdclk_0 =  0x00020030,
+	.dram_sdclk_1 =  0x00020030,
+	.dram_cas =  0x00020030,
+	.dram_ras =  0x00020030,
+	.dram_reset =  0x00020030,
+	.dram_sdcke0 =  0x00003000,
+	.dram_sdcke1 =  0x00003000,
+	.dram_sdba2 =  0x00000000,
+	.dram_sdodt0 =  0x00003030,
+	.dram_sdodt1 =  0x00003030,
+	.dram_sdqs0 =  0x00000030,
+	.dram_sdqs1 =  0x00000030,
+	.dram_sdqs2 =  0x00000030,
+	.dram_sdqs3 =  0x00000030,
+	.dram_sdqs4 =  0x00000030,
+	.dram_sdqs5 =  0x00000030,
+	.dram_sdqs6 =  0x00000030,
+	.dram_sdqs7 =  0x00000030,
+	.dram_dqm0 =  0x00020030,
+	.dram_dqm1 =  0x00020030,
+	.dram_dqm2 =  0x00020030,
+	.dram_dqm3 =  0x00020030,
+	.dram_dqm4 =  0x00020030,
+	.dram_dqm5 =  0x00020030,
+	.dram_dqm6 =  0x00020030,
+	.dram_dqm7 =  0x00020030,
+};
+
+const struct mx6dq_iomux_grp_regs mx6_grp_ioregs = {
+	.grp_ddr_type =  0x000C0000,
+	.grp_ddrmode_ctl =  0x00020000,
+	.grp_ddrpke =  0x00000000,
+	.grp_addds =  0x00000030,
+	.grp_ctlds =  0x00000030,
+	.grp_ddrmode =  0x00020000,
+	.grp_b0ds =  0x00000030,
+	.grp_b1ds =  0x00000030,
+	.grp_b2ds =  0x00000030,
+	.grp_b3ds =  0x00000030,
+	.grp_b4ds =  0x00000030,
+	.grp_b5ds =  0x00000030,
+	.grp_b6ds =  0x00000030,
+	.grp_b7ds =  0x00000030,
+};
+
+const struct mx6_mmdc_calibration mx6_mmcd_calib = {
+	.p0_mpwldectrl0 =  0x001F001F,
+	.p0_mpwldectrl1 =  0x001F001F,
+	.p1_mpwldectrl0 =  0x00440044,
+	.p1_mpwldectrl1 =  0x00440044,
+	.p0_mpdgctrl0 =  0x434B0350,
+	.p0_mpdgctrl1 =  0x034C0359,
+	.p1_mpdgctrl0 =  0x434B0350,
+	.p1_mpdgctrl1 =  0x03650348,
+	.p0_mprddlctl =  0x4436383B,
+	.p1_mprddlctl =  0x39393341,
+	.p0_mpwrdlctl =  0x35373933,
+	.p1_mpwrdlctl =  0x48254A36,
+};
+
+static struct mx6_ddr3_cfg mem_ddr = {
+	.mem_speed = 1600,
+	.density = 4,
+	.width = 64,
+	.banks = 8,
+	.rowaddr = 14,
+	.coladdr = 10,
+	.pagesz = 2,
+	.trcd = 1375,
+	.trcmin = 4875,
+	.trasmin = 3500,
+};
+
+/*
+ * This section require the differentiation
+ * between iMX6 Sabre Families.
+ * But for now, it will configure only for
+ * SabreSD.
+ */
+static void spl_dram_init(void)
+{
+	struct mx6_ddr_sysinfo sysinfo = {
+		/* width of data bus:0=16,1=32,2=64 */
+		.dsize = mem_ddr.width/32,
+		/* config for full 4GB range so that get_mem_size() works */
+		.cs_density = 32, /* 32Gb per CS */
+		/* single chip select */
+		.ncs = 1,
+		.cs1_mirror = 0,
+		.rtt_wr = 1 /*DDR3_RTT_60_OHM*/,	/* RTT_Wr = RZQ/4 */
+#ifdef RTT_NOM_120OHM
+		.rtt_nom = 2 /*DDR3_RTT_120_OHM*/,	/* RTT_Nom = RZQ/2 */
+#else
+		.rtt_nom = 1 /*DDR3_RTT_60_OHM*/,	/* RTT_Nom = RZQ/4 */
+#endif
+		.walat = 1,	/* Write additional latency */
+		.ralat = 5,	/* Read additional latency */
+		.mif3_mode = 3,	/* Command prediction working mode */
+		.bi_on = 1,	/* Bank interleaving enabled */
+		.sde_to_rst = 0x10,	/* 14 cycles, 200us (JEDEC default) */
+		.rst_to_cke = 0x23,	/* 33 cycles, 500us (JEDEC default) */
+	};
+
+	mx6dq_dram_iocfg(mem_ddr.width, &mx6_ddr_ioregs, &mx6_grp_ioregs);
+	mx6_dram_cfg(&sysinfo, &mx6_mmcd_calib, &mem_ddr);
+}
+
+void board_init_f(ulong dummy)
+{
+	/* setup AIPS and disable watchdog */
+	arch_cpu_init();
+
+	/* iomux and setup of i2c */
+	board_early_init_f();
+
+	/* setup GP timer */
+	timer_init();
+
+	/* UART clocks enabled and gd valid - init serial console */
+	preloader_console_init();
+
+	/* DDR initialization */
+	spl_dram_init();
+
+	/* Clear the BSS. */
+	memset(__bss_start, 0, __bss_end - __bss_start);
+
+	/* load/boot image from boot device */
+	board_init_r(NULL, 0);
+}
+
+void reset_cpu(ulong addr)
+{
+}
+#endif
diff --git a/board/freescale/mx6sabresd/mx6sabresd_spl.cfg b/board/freescale/mx6sabresd/mx6sabresd_spl.cfg
new file mode 100644
index 0000000..2bf4817
--- /dev/null
+++ b/board/freescale/mx6sabresd/mx6sabresd_spl.cfg
@@ -0,0 +1,58 @@
+/*
+ * Copyright (C) 2011 Freescale Semiconductor, Inc.
+ * Jason Liu <r64343@freescale.com>
+ *
+ * SPDX-License-Identifier:	GPL-2.0+
+ *
+ * Refer doc/README.imximage for more details about how-to configure
+ * and create imximage boot image
+ *
+ * The syntax is taken as close as possible with the kwbimage
+ */
+
+/* image version */
+IMAGE_VERSION 2
+
+/*
+ * Boot Device : one of
+ * spi, sd (the board has no nand neither onenand)
+ */
+BOOT_FROM      sd
+
+/*
+ * Device Configuration Data (DCD)
+ *
+ * Each entry must have the format:
+ * Addr-type           Address        Value
+ *
+ * where:
+ *      Addr-type register length (1,2 or 4 bytes)
+ *      Address   absolute address of the register
+ *      value     value to be stored in the register
+ */
+
+/* set the default clock gate to save power */
+DATA 4 0x020c4068 0x00C03F3F
+DATA 4 0x020c406c 0x0030FC03
+DATA 4 0x020c4070 0x0FFFC000
+DATA 4 0x020c4074 0x3FF00000
+DATA 4 0x020c4078 0x00FFF300
+DATA 4 0x020c407c 0x0F0000C3
+DATA 4 0x020c4080 0x000003FF
+
+/* enable AXI cache for VDOA/VPU/IPU */
+DATA 4 0x020e0010 0xF00000CF
+/* set IPU AXI-id0 Qos=0xf(bypass) AXI-id1 Qos=0x7 */
+DATA 4 0x020e0018 0x007F007F
+DATA 4 0x020e001c 0x007F007F
+
+/*
+ * Setup CCM_CCOSR register as follows:
+ *
+ * cko1_en  = 1	   --> CKO1 enabled
+ * cko1_div = 111  --> divide by 8
+ * cko1_sel = 1011 --> ahb_clk_root
+ *
+ * This sets CKO1 at ahb_clk_root/8 = 132/8 = 16.5 MHz
+ */
+DATA 4 0x020c4060 0x000000fb
diff --git a/board/tbs/tbs2910/Kconfig b/board/tbs/tbs2910/Kconfig
new file mode 100644
index 0000000..c514e24
--- /dev/null
+++ b/board/tbs/tbs2910/Kconfig
@@ -0,0 +1,23 @@
+if TARGET_TBS2910
+
+config SYS_CPU
+	string
+	default "armv7"
+
+config SYS_BOARD
+	string
+	default "tbs2910"
+
+config SYS_VENDOR
+	string
+	default "tbs"
+
+config SYS_SOC
+	string
+	default "mx6"
+
+config SYS_CONFIG_NAME
+	string
+	default "tbs2910"
+
+endif
diff --git a/board/tbs/tbs2910/MAINTAINERS b/board/tbs/tbs2910/MAINTAINERS
new file mode 100644
index 0000000..bf17655
--- /dev/null
+++ b/board/tbs/tbs2910/MAINTAINERS
@@ -0,0 +1,6 @@
+TBS2910 BOARD
+M:	Soeren Moch <smoch@web.de>
+S:	Maintained
+F:	board/tbs/tbs2910/
+F:	configs/tbs2910_defconfig
+F:	include/configs/tbs2910.h
diff --git a/board/tbs/tbs2910/Makefile b/board/tbs/tbs2910/Makefile
new file mode 100644
index 0000000..9d9eb87
--- /dev/null
+++ b/board/tbs/tbs2910/Makefile
@@ -0,0 +1,7 @@
+#
+# Copyright (C) 2014 Soeren Moch <smoch@web.de>
+#
+# SPDX-License-Identifier:	GPL-2.0+
+#
+
+obj-y  := tbs2910.o
diff --git a/board/tbs/tbs2910/tbs2910.c b/board/tbs/tbs2910/tbs2910.c
new file mode 100644
index 0000000..daf8ff4
--- /dev/null
+++ b/board/tbs/tbs2910/tbs2910.c
@@ -0,0 +1,398 @@
+/*
+ * Copyright (C) 2014 Soeren Moch <smoch@web.de>
+ *
+ * SPDX-License-Identifier:	GPL-2.0+
+ */
+
+#include <asm/arch/clock.h>
+#include <asm/arch/imx-regs.h>
+#include <asm/arch/iomux.h>
+#include <asm/arch/mx6-pins.h>
+#include <asm/errno.h>
+#include <asm/gpio.h>
+#include <asm/imx-common/mxc_i2c.h>
+#include <asm/imx-common/iomux-v3.h>
+#include <asm/imx-common/sata.h>
+#include <asm/imx-common/boot_mode.h>
+#include <asm/imx-common/video.h>
+#include <mmc.h>
+#include <fsl_esdhc.h>
+#include <miiphy.h>
+#include <netdev.h>
+#include <asm/arch/mxc_hdmi.h>
+#include <asm/arch/crm_regs.h>
+#include <asm/io.h>
+#include <asm/arch/sys_proto.h>
+#include <i2c.h>
+DECLARE_GLOBAL_DATA_PTR;
+
+#define WEAK_PULLUP	(PAD_CTL_PUS_47K_UP |			\
+	PAD_CTL_SPEED_LOW | PAD_CTL_DSE_40ohm | PAD_CTL_HYS |	\
+	PAD_CTL_SRE_SLOW)
+
+#define UART_PAD_CTRL  (PAD_CTL_PUS_100K_UP |			\
+	PAD_CTL_SPEED_MED | PAD_CTL_DSE_40ohm |			\
+	PAD_CTL_SRE_FAST  | PAD_CTL_HYS)
+
+#define USDHC_PAD_CTRL (PAD_CTL_PUS_47K_UP |			\
+	PAD_CTL_SPEED_LOW | PAD_CTL_DSE_80ohm |			\
+	PAD_CTL_SRE_FAST  | PAD_CTL_HYS)
+
+#define ENET_PAD_CTRL  (PAD_CTL_PUS_100K_UP |			\
+	PAD_CTL_SPEED_MED | PAD_CTL_DSE_40ohm | PAD_CTL_HYS)
+
+#define I2C_PAD_CTRL  (PAD_CTL_PUS_100K_UP |			\
+	PAD_CTL_SPEED_MED | PAD_CTL_DSE_40ohm | PAD_CTL_HYS |	\
+	PAD_CTL_ODE | PAD_CTL_SRE_FAST)
+
+#define I2C_PAD MUX_PAD_CTRL(I2C_PAD_CTRL)
+
+#ifdef CONFIG_SYS_I2C
+/* I2C1, SGTL5000 */
+static struct i2c_pads_info i2c_pad_info0 = {
+	.scl = {
+		.i2c_mode = MX6_PAD_CSI0_DAT9__I2C1_SCL | I2C_PAD,
+		.gpio_mode = MX6_PAD_CSI0_DAT9__GPIO5_IO27 | I2C_PAD,
+		.gp = IMX_GPIO_NR(5, 27)
+	},
+	.sda = {
+		.i2c_mode = MX6_PAD_CSI0_DAT8__I2C1_SDA | I2C_PAD,
+		.gpio_mode = MX6_PAD_CSI0_DAT8__GPIO5_IO26 | I2C_PAD,
+		.gp = IMX_GPIO_NR(5, 26)
+	}
+};
+
+/* I2C2 HDMI */
+static struct i2c_pads_info i2c_pad_info1 = {
+	.scl = {
+		.i2c_mode = MX6_PAD_KEY_COL3__I2C2_SCL | I2C_PAD,
+		.gpio_mode = MX6_PAD_KEY_COL3__GPIO4_IO12 | I2C_PAD,
+		.gp = IMX_GPIO_NR(4, 12)
+	},
+	.sda = {
+		.i2c_mode = MX6_PAD_KEY_ROW3__I2C2_SDA | I2C_PAD,
+		.gpio_mode = MX6_PAD_KEY_ROW3__GPIO4_IO13 | I2C_PAD,
+		.gp = IMX_GPIO_NR(4, 13)
+	}
+};
+
+/* I2C3, CON11, DS1307, PCIe_SMB */
+static struct i2c_pads_info i2c_pad_info2 = {
+	.scl = {
+		.i2c_mode = MX6_PAD_GPIO_3__I2C3_SCL | I2C_PAD,
+		.gpio_mode = MX6_PAD_GPIO_3__GPIO1_IO03 | I2C_PAD,
+		.gp = IMX_GPIO_NR(1, 3)
+	},
+	.sda = {
+		.i2c_mode = MX6_PAD_GPIO_6__I2C3_SDA | I2C_PAD,
+		.gpio_mode = MX6_PAD_GPIO_6__GPIO1_IO06 | I2C_PAD,
+		.gp = IMX_GPIO_NR(1, 6)
+	}
+};
+#endif /* CONFIG_SYS_I2C */
+
+static iomux_v3_cfg_t const uart1_pads[] = {
+	MX6_PAD_CSI0_DAT10__UART1_TX_DATA | MUX_PAD_CTRL(UART_PAD_CTRL),
+	MX6_PAD_CSI0_DAT11__UART1_RX_DATA | MUX_PAD_CTRL(UART_PAD_CTRL),
+};
+
+static iomux_v3_cfg_t const uart2_pads[] = {
+	MX6_PAD_EIM_D26__UART2_TX_DATA | MUX_PAD_CTRL(UART_PAD_CTRL),
+	MX6_PAD_EIM_D27__UART2_RX_DATA | MUX_PAD_CTRL(UART_PAD_CTRL),
+};
+
+static iomux_v3_cfg_t const enet_pads[] = {
+	MX6_PAD_ENET_MDIO__ENET_MDIO		| MUX_PAD_CTRL(ENET_PAD_CTRL),
+	MX6_PAD_ENET_MDC__ENET_MDC		| MUX_PAD_CTRL(ENET_PAD_CTRL),
+	MX6_PAD_RGMII_TXC__RGMII_TXC		| MUX_PAD_CTRL(ENET_PAD_CTRL),
+	MX6_PAD_RGMII_TD0__RGMII_TD0		| MUX_PAD_CTRL(ENET_PAD_CTRL),
+	MX6_PAD_RGMII_TD1__RGMII_TD1		| MUX_PAD_CTRL(ENET_PAD_CTRL),
+	MX6_PAD_RGMII_TD2__RGMII_TD2		| MUX_PAD_CTRL(ENET_PAD_CTRL),
+	MX6_PAD_RGMII_TD3__RGMII_TD3		| MUX_PAD_CTRL(ENET_PAD_CTRL),
+	MX6_PAD_RGMII_TX_CTL__RGMII_TX_CTL	| MUX_PAD_CTRL(ENET_PAD_CTRL),
+	MX6_PAD_ENET_REF_CLK__ENET_TX_CLK	| MUX_PAD_CTRL(ENET_PAD_CTRL),
+	MX6_PAD_RGMII_RXC__RGMII_RXC		| MUX_PAD_CTRL(ENET_PAD_CTRL),
+	MX6_PAD_RGMII_RD0__RGMII_RD0		| MUX_PAD_CTRL(ENET_PAD_CTRL),
+	MX6_PAD_RGMII_RD1__RGMII_RD1		| MUX_PAD_CTRL(ENET_PAD_CTRL),
+	MX6_PAD_RGMII_RD2__RGMII_RD2		| MUX_PAD_CTRL(ENET_PAD_CTRL),
+	MX6_PAD_RGMII_RD3__RGMII_RD3		| MUX_PAD_CTRL(ENET_PAD_CTRL),
+	MX6_PAD_RGMII_RX_CTL__RGMII_RX_CTL	| MUX_PAD_CTRL(ENET_PAD_CTRL),
+	/* AR8035 PHY Reset */
+	MX6_PAD_ENET_CRS_DV__GPIO1_IO25		| MUX_PAD_CTRL(NO_PAD_CTRL),
+};
+
+static iomux_v3_cfg_t const pcie_pads[] = {
+	/* W_DISABLE# */
+	MX6_PAD_KEY_COL4__GPIO4_IO14 | MUX_PAD_CTRL(WEAK_PULLUP),
+	/* PERST# */
+	MX6_PAD_GPIO_17__GPIO7_IO12  | MUX_PAD_CTRL(NO_PAD_CTRL),
+};
+
+int dram_init(void)
+{
+	gd->ram_size = 2048ul * 1024 * 1024;
+	return 0;
+}
+
+static void setup_iomux_enet(void)
+{
+	imx_iomux_v3_setup_multiple_pads(enet_pads, ARRAY_SIZE(enet_pads));
+
+	/* Reset AR8035 PHY */
+	gpio_direction_output(IMX_GPIO_NR(1, 25) , 0);
+	udelay(500);
+	gpio_set_value(IMX_GPIO_NR(1, 25), 1);
+}
+
+static void setup_pcie(void)
+{
+	imx_iomux_v3_setup_multiple_pads(pcie_pads, ARRAY_SIZE(pcie_pads));
+}
+
+static void setup_iomux_uart(void)
+{
+	imx_iomux_v3_setup_multiple_pads(uart1_pads, ARRAY_SIZE(uart1_pads));
+	imx_iomux_v3_setup_multiple_pads(uart2_pads, ARRAY_SIZE(uart2_pads));
+}
+
+#ifdef CONFIG_FSL_ESDHC
+static iomux_v3_cfg_t const usdhc2_pads[] = {
+	MX6_PAD_SD2_CLK__SD2_CLK     | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+	MX6_PAD_SD2_CMD__SD2_CMD     | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+	MX6_PAD_SD2_DAT0__SD2_DATA0  | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+	MX6_PAD_SD2_DAT1__SD2_DATA1  | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+	MX6_PAD_SD2_DAT2__SD2_DATA2  | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+	MX6_PAD_SD2_DAT3__SD2_DATA3  | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+	MX6_PAD_NANDF_D2__GPIO2_IO02 | MUX_PAD_CTRL(NO_PAD_CTRL), /* CD */
+};
+
+static iomux_v3_cfg_t const usdhc3_pads[] = {
+	MX6_PAD_SD3_CLK__SD3_CLK     | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+	MX6_PAD_SD3_CMD__SD3_CMD     | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+	MX6_PAD_SD3_DAT0__SD3_DATA0  | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+	MX6_PAD_SD3_DAT1__SD3_DATA1  | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+	MX6_PAD_SD3_DAT2__SD3_DATA2  | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+	MX6_PAD_SD3_DAT3__SD3_DATA3  | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+	MX6_PAD_NANDF_D0__GPIO2_IO00 | MUX_PAD_CTRL(NO_PAD_CTRL), /* CD */
+};
+
+static iomux_v3_cfg_t const usdhc4_pads[] = {
+	MX6_PAD_SD4_CLK__SD4_CLK    | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+	MX6_PAD_SD4_CMD__SD4_CMD    | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+	MX6_PAD_SD4_DAT0__SD4_DATA0 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+	MX6_PAD_SD4_DAT1__SD4_DATA1 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+	MX6_PAD_SD4_DAT2__SD4_DATA2 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+	MX6_PAD_SD4_DAT3__SD4_DATA3 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+	MX6_PAD_SD4_DAT4__SD4_DATA4 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+	MX6_PAD_SD4_DAT5__SD4_DATA5 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+	MX6_PAD_SD4_DAT6__SD4_DATA6 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+	MX6_PAD_SD4_DAT7__SD4_DATA7 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+};
+
+static struct fsl_esdhc_cfg usdhc_cfg[3] = {
+	{USDHC2_BASE_ADDR},
+	{USDHC3_BASE_ADDR},
+	{USDHC4_BASE_ADDR},
+};
+
+#define USDHC2_CD_GPIO	IMX_GPIO_NR(2, 2)
+#define USDHC3_CD_GPIO	IMX_GPIO_NR(2, 0)
+
+int board_mmc_getcd(struct mmc *mmc)
+{
+	struct fsl_esdhc_cfg *cfg = (struct fsl_esdhc_cfg *)mmc->priv;
+	int ret = 0;
+
+	switch (cfg->esdhc_base) {
+	case USDHC2_BASE_ADDR:
+		ret = !gpio_get_value(USDHC2_CD_GPIO);
+		break;
+	case USDHC3_BASE_ADDR:
+		ret = !gpio_get_value(USDHC3_CD_GPIO);
+		break;
+	case USDHC4_BASE_ADDR:
+		ret = 1; /* eMMC/uSDHC4 is always present */
+		break;
+	}
+	return ret;
+}
+
+int board_mmc_init(bd_t *bis)
+{
+	s32 status = 0;
+	int i;
+
+	/*
+	 * (U-boot device node)    (Physical Port)
+	 * mmc0                    SD2
+	 * mmc1                    SD3
+	 * mmc2                    eMMC
+	 */
+	for (i = 0; i < CONFIG_SYS_FSL_USDHC_NUM; i++) {
+		switch (i) {
+		case 0:
+			imx_iomux_v3_setup_multiple_pads(
+				usdhc2_pads, ARRAY_SIZE(usdhc2_pads));
+			gpio_direction_input(USDHC2_CD_GPIO);
+			usdhc_cfg[0].sdhc_clk = mxc_get_clock(MXC_ESDHC2_CLK);
+			break;
+		case 1:
+			imx_iomux_v3_setup_multiple_pads(
+				usdhc3_pads, ARRAY_SIZE(usdhc3_pads));
+			gpio_direction_input(USDHC3_CD_GPIO);
+			usdhc_cfg[1].sdhc_clk = mxc_get_clock(MXC_ESDHC3_CLK);
+			break;
+		case 2:
+			imx_iomux_v3_setup_multiple_pads(
+				usdhc4_pads, ARRAY_SIZE(usdhc4_pads));
+			usdhc_cfg[2].sdhc_clk = mxc_get_clock(MXC_ESDHC4_CLK);
+			break;
+		default:
+			printf("Warning: you configured more USDHC controllers"
+			       "(%d) then supported by the board (%d)\n",
+			       i + 1, CONFIG_SYS_FSL_USDHC_NUM);
+			return status;
+		}
+
+		status |= fsl_esdhc_initialize(bis, &usdhc_cfg[i]);
+	}
+	return status;
+}
+#endif /* CONFIG_FSL_ESDHC */
+
+#ifdef CONFIG_VIDEO_IPUV3
+static void do_enable_hdmi(struct display_info_t const *dev)
+{
+	imx_enable_hdmi_phy();
+}
+
+struct display_info_t const displays[] = {{
+	.bus	= -1,
+	.addr	= 0,
+	.pixfmt	= IPU_PIX_FMT_RGB24,
+	.detect	= detect_hdmi,
+	.enable	= do_enable_hdmi,
+	.mode	= {
+		.name           = "HDMI",
+		/* 1024x768@60Hz (VESA)*/
+		.refresh        = 60,
+		.xres           = 1024,
+		.yres           = 768,
+		.pixclock       = 15384,
+		.left_margin    = 160,
+		.right_margin   = 24,
+		.upper_margin   = 29,
+		.lower_margin   = 3,
+		.hsync_len      = 136,
+		.vsync_len      = 6,
+		.sync           = FB_SYNC_EXT,
+		.vmode          = FB_VMODE_NONINTERLACED
+} } };
+size_t display_count = ARRAY_SIZE(displays);
+
+static void setup_display(void)
+{
+	struct mxc_ccm_reg *ccm = (struct mxc_ccm_reg *)CCM_BASE_ADDR;
+	int reg;
+	s32 timeout = 100000;
+
+	enable_ipu_clock();
+	imx_setup_hdmi();
+
+	/* set video pll to 455MHz (24MHz * (37+11/12) / 2) */
+	reg = readl(&ccm->analog_pll_video);
+	reg |= BM_ANADIG_PLL_VIDEO_POWERDOWN;
+	writel(reg, &ccm->analog_pll_video);
+
+	reg &= ~BM_ANADIG_PLL_VIDEO_DIV_SELECT;
+	reg |= BF_ANADIG_PLL_VIDEO_DIV_SELECT(37);
+	reg &= ~BM_ANADIG_PLL_VIDEO_POST_DIV_SELECT;
+	reg |= BF_ANADIG_PLL_VIDEO_POST_DIV_SELECT(1);
+	writel(reg, &ccm->analog_pll_video);
+
+	writel(BF_ANADIG_PLL_VIDEO_NUM_A(11), &ccm->analog_pll_video_num);
+	writel(BF_ANADIG_PLL_VIDEO_DENOM_B(12), &ccm->analog_pll_video_denom);
+
+	reg &= ~BM_ANADIG_PLL_VIDEO_POWERDOWN;
+	writel(reg, &ccm->analog_pll_video);
+
+	while (timeout--)
+		if (readl(&ccm->analog_pll_video) & BM_ANADIG_PLL_VIDEO_LOCK)
+			break;
+	if (timeout < 0)
+		printf("Warning: video pll lock timeout!\n");
+
+	reg = readl(&ccm->analog_pll_video);
+	reg |= BM_ANADIG_PLL_VIDEO_ENABLE;
+	reg &= ~BM_ANADIG_PLL_VIDEO_BYPASS;
+	writel(reg, &ccm->analog_pll_video);
+
+	/* select video pll for ldb_di0_clk */
+	reg = readl(&ccm->cs2cdr);
+	reg &= ~(MXC_CCM_CS2CDR_LDB_DI0_CLK_SEL_MASK);
+	writel(reg, &ccm->cs2cdr);
+
+	/* select ldb_di0_clk / 7 for ldb_di0_ipu_clk */
+	reg = readl(&ccm->cscmr2);
+	reg |= MXC_CCM_CSCMR2_LDB_DI0_IPU_DIV;
+	writel(reg, &ccm->cscmr2);
+
+	/* select ldb_di0_ipu_clk for ipu1_di0_clk -> 65MHz pixclock */
+	reg = readl(&ccm->chsccdr);
+	reg |= (CHSCCDR_CLK_SEL_LDB_DI0
+		<< MXC_CCM_CHSCCDR_IPU1_DI0_CLK_SEL_OFFSET);
+	writel(reg, &ccm->chsccdr);
+}
+#endif /* CONFIG_VIDEO_IPUV3 */
+
+int board_eth_init(bd_t *bis)
+{
+	setup_iomux_enet();
+	setup_pcie();
+	return cpu_eth_init(bis);
+}
+
+int board_early_init_f(void)
+{
+	setup_iomux_uart();
+	return 0;
+}
+
+#ifdef CONFIG_CMD_BMODE
+static const struct boot_mode board_boot_modes[] = {
+	/* 4 bit bus width */
+	{"sd2",	 MAKE_CFGVAL(0x40, 0x28, 0x00, 0x00)},
+	{"sd3",	 MAKE_CFGVAL(0x40, 0x30, 0x00, 0x00)},
+	/* 8 bit bus width */
+	{"emmc", MAKE_CFGVAL(0x40, 0x38, 0x00, 0x00)},
+	{NULL,	 0},
+};
+#endif
+
+int board_init(void)
+{
+	/* address of boot parameters */
+	gd->bd->bi_boot_params = CONFIG_SYS_SDRAM_BASE + 0x100;
+
+#ifdef CONFIG_VIDEO_IPUV3
+	setup_display();
+#endif
+#ifdef CONFIG_SYS_I2C
+	setup_i2c(0, CONFIG_SYS_I2C_SPEED, 0x7f, &i2c_pad_info0);
+	setup_i2c(1, CONFIG_SYS_I2C_SPEED, 0x7f, &i2c_pad_info1);
+	setup_i2c(2, CONFIG_SYS_I2C_SPEED, 0x7f, &i2c_pad_info2);
+#endif
+#ifdef CONFIG_DWC_AHSATA
+	setup_sata();
+#endif
+#ifdef CONFIG_CMD_BMODE
+	add_board_boot_modes(board_boot_modes);
+#endif
+	return 0;
+}
+
+int checkboard(void)
+{
+	puts("Board: TBS2910 Matrix ARM mini PC\n");
+	return 0;
+}
diff --git a/configs/mx6sabresd_spl_defconfig b/configs/mx6sabresd_spl_defconfig
new file mode 100644
index 0000000..b7b26df
--- /dev/null
+++ b/configs/mx6sabresd_spl_defconfig
@@ -0,0 +1,5 @@
+CONFIG_SPL=y
+CONFIG_SYS_EXTRA_OPTIONS="IMX_CONFIG=board/freescale/mx6sabresd/mx6sabresd_spl.cfg,SPL,MX6Q"
++S:CONFIG_ARM=y
++S:CONFIG_TARGET_MX6SABRESD=y
+
diff --git a/configs/tbs2910_defconfig b/configs/tbs2910_defconfig
new file mode 100644
index 0000000..602d691
--- /dev/null
+++ b/configs/tbs2910_defconfig
@@ -0,0 +1,3 @@
+CONFIG_SYS_EXTRA_OPTIONS="IMX_CONFIG=board/boundary/nitrogen6x/nitrogen6q2g.cfg,MX6Q"
+CONFIG_ARM=y
+CONFIG_TARGET_TBS2910=y
diff --git a/include/configs/mx53loco.h b/include/configs/mx53loco.h
index a74508c..10fb1f4 100644
--- a/include/configs/mx53loco.h
+++ b/include/configs/mx53loco.h
@@ -107,7 +107,6 @@
 #define CONFIG_EXTRA_ENV_SETTINGS \
 	"script=boot.scr\0" \
 	"image=zImage\0" \
-	"fdt_file=imx53-qsb.dtb\0" \
 	"fdt_addr=0x71000000\0" \
 	"boot_fdt=try\0" \
 	"ip_dyn=yes\0" \
diff --git a/include/configs/mx6qsabreauto.h b/include/configs/mx6qsabreauto.h
index 235dd6d..3f1c88e 100644
--- a/include/configs/mx6qsabreauto.h
+++ b/include/configs/mx6qsabreauto.h
@@ -48,4 +48,20 @@
 #define CONFIG_SYS_I2C_MXC
 #define CONFIG_SYS_I2C_SPEED		100000
 
+/* NAND flash command */
+#define CONFIG_CMD_NAND
+#define CONFIG_CMD_NAND_TRIMFFS
+
+/* NAND stuff */
+#define CONFIG_NAND_MXS
+#define CONFIG_SYS_MAX_NAND_DEVICE     1
+#define CONFIG_SYS_NAND_BASE           0x40000000
+#define CONFIG_SYS_NAND_5_ADDR_CYCLE
+#define CONFIG_SYS_NAND_ONFI_DETECTION
+
+/* DMA stuff, needed for GPMI/MXS NAND support */
+#define CONFIG_APBH_DMA
+#define CONFIG_APBH_DMA_BURST
+#define CONFIG_APBH_DMA_BURST8
+
 #endif                         /* __MX6QSABREAUTO_CONFIG_H */
diff --git a/include/configs/mx6sabre_common.h b/include/configs/mx6sabre_common.h
index c81e9e9..1e10422 100644
--- a/include/configs/mx6sabre_common.h
+++ b/include/configs/mx6sabre_common.h
@@ -251,7 +251,7 @@
 #define CONFIG_ENV_IS_IN_MMC
 
 #if defined(CONFIG_ENV_IS_IN_MMC)
-#define CONFIG_ENV_OFFSET		(6 * 64 * 1024)
+#define CONFIG_ENV_OFFSET		(8 * 64 * 1024)
 #endif
 
 #define CONFIG_OF_LIBFDT
diff --git a/include/configs/mx6sabresd.h b/include/configs/mx6sabresd.h
index 938030d..a346542 100644
--- a/include/configs/mx6sabresd.h
+++ b/include/configs/mx6sabresd.h
@@ -12,6 +12,12 @@
 #include <asm/arch/imx-regs.h>
 #include <asm/imx-common/gpio.h>
 
+#ifdef CONFIG_SPL
+#define CONFIG_SPL_LIBCOMMON_SUPPORT
+#define CONFIG_SPL_MMC_SUPPORT
+#include "imx6_spl.h"
+#endif
+
 #define CONFIG_MACH_TYPE	3980
 #define CONFIG_MXC_UART_BASE	UART1_BASE
 #define CONFIG_CONSOLE_DEV		"ttymxc0"
diff --git a/include/configs/ot1200.h b/include/configs/ot1200.h
index d7696bd..9512b1e 100644
--- a/include/configs/ot1200.h
+++ b/include/configs/ot1200.h
@@ -83,6 +83,13 @@
 #define CONFIG_GENERIC_MMC
 #define CONFIG_BOUNCE_BUFFER
 
+/* USB Configs */
+#define CONFIG_CMD_USB
+#define CONFIG_USB_EHCI
+#define CONFIG_USB_EHCI_MX6
+#define CONFIG_MXC_USB_PORTSC   (PORT_PTS_UTMI | PORT_PTS_PTW)
+#define CONFIG_USB_MAX_CONTROLLER_COUNT 2
+
 #ifdef CONFIG_MX6Q
 #define CONFIG_CMD_SATA
 #endif
diff --git a/include/configs/tbs2910.h b/include/configs/tbs2910.h
new file mode 100644
index 0000000..6ab2184
--- /dev/null
+++ b/include/configs/tbs2910.h
@@ -0,0 +1,242 @@
+/*
+ * Copyright (C) 2014 Soeren Moch <smoch@web.de>
+ *
+ * Configuration settings for the TBS2910 MatrixARM board.
+ *
+ * SPDX-License-Identifier:	GPL-2.0+
+ */
+
+#ifndef __TBS2910_CONFIG_H
+#define __TBS2910_CONFIG_H
+
+#include "mx6_common.h"
+#include <asm/arch/imx-regs.h>
+#include <asm/imx-common/gpio.h>
+
+/* General configuration */
+#define CONFIG_MX6
+#define CONFIG_DISPLAY_CPUINFO
+#define CONFIG_DISPLAY_BOARDINFO_LATE
+#define CONFIG_SYS_THUMB_BUILD
+
+#define CONFIG_MACH_TYPE		3980
+
+#define CONFIG_CMDLINE_TAG
+#define CONFIG_SETUP_MEMORY_TAGS
+#define CONFIG_INITRD_TAG
+#define CONFIG_REVISION_TAG
+#define CONFIG_SYS_GENERIC_BOARD
+
+#define CONFIG_BOARD_EARLY_INIT_F
+#define CONFIG_MXC_GPIO
+#define CONFIG_CMD_GPIO
+
+#define CONFIG_SYS_LONGHELP
+#define CONFIG_SYS_HUSH_PARSER
+#define CONFIG_SYS_PROMPT		"Matrix U-Boot> "
+#define CONFIG_BOOTDELAY		3
+#define CONFIG_AUTO_COMPLETE
+#define CONFIG_CMDLINE_EDITING
+#define CONFIG_SYS_MAXARGS		16
+#define CONFIG_SYS_CBSIZE		1024
+#define CONFIG_SYS_PBSIZE \
+	(CONFIG_SYS_CBSIZE + sizeof(CONFIG_SYS_PROMPT) + 16)
+#define CONFIG_SYS_HZ			1000
+
+/* Physical Memory Map */
+#define CONFIG_NR_DRAM_BANKS		1
+#define CONFIG_SYS_SDRAM_BASE		MMDC0_ARB_BASE_ADDR
+
+#define CONFIG_SYS_INIT_RAM_ADDR	IRAM_BASE_ADDR
+#define CONFIG_SYS_INIT_RAM_SIZE	IRAM_SIZE
+#define CONFIG_SYS_INIT_SP_OFFSET \
+	(CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
+#define CONFIG_SYS_INIT_SP_ADDR \
+	(CONFIG_SYS_INIT_RAM_ADDR + CONFIG_SYS_INIT_SP_OFFSET)
+
+#define CONFIG_SYS_MALLOC_LEN		(128 * 1024 * 1024)
+
+#define CONFIG_SYS_MEMTEST_START	CONFIG_SYS_SDRAM_BASE
+#define CONFIG_SYS_MEMTEST_END \
+	(CONFIG_SYS_MEMTEST_START + 500 * 1024 * 1024)
+
+#define CONFIG_SYS_TEXT_BASE		0x80000000
+#define CONFIG_SYS_BOOTMAPSZ		0x6C000000
+#define CONFIG_SYS_LOAD_ADDR		0x10800000
+
+/* Serial console */
+#define CONFIG_MXC_UART
+#define CONFIG_MXC_UART_BASE		UART1_BASE /* select UART1/UART2 */
+#define CONFIG_BAUDRATE			115200
+
+#define CONFIG_SYS_CONSOLE_IS_IN_ENV
+#define CONFIG_CONSOLE_MUX
+#define CONFIG_CONS_INDEX		1
+
+/* *** Command definition *** */
+#include <config_cmd_default.h>
+
+#undef CONFIG_CMD_IMLS
+
+#define CONFIG_CMD_BMODE
+#define CONFIG_CMD_SETEXPR
+#define CONFIG_CMD_MEMTEST
+#define CONFIG_CMD_TIME
+
+/* Filesystems / image support */
+#define CONFIG_CMD_EXT4
+#define CONFIG_CMD_FAT
+#define CONFIG_DOS_PARTITION
+#define CONFIG_EFI_PARTITION
+#define CONFIG_CMD_FS_GENERIC
+
+#define CONFIG_OF_LIBFDT
+#define CONFIG_CMD_BOOTZ
+#define CONFIG_SUPPORT_RAW_INITRD
+#define CONFIG_FIT
+
+/* MMC */
+#define CONFIG_FSL_ESDHC
+#define CONFIG_FSL_USDHC
+#define CONFIG_SYS_FSL_USDHC_NUM	3
+#define CONFIG_SYS_FSL_ESDHC_ADDR	USDHC4_BASE_ADDR
+
+#define CONFIG_MMC
+#define CONFIG_CMD_MMC
+#define CONFIG_GENERIC_MMC
+#define CONFIG_BOUNCE_BUFFER
+
+/* Ethernet */
+#define CONFIG_FEC_MXC
+#define CONFIG_CMD_PING
+#define CONFIG_CMD_DHCP
+#define CONFIG_CMD_MII
+#define CONFIG_CMD_NET
+#define CONFIG_FEC_MXC
+#define CONFIG_MII
+#define IMX_FEC_BASE			ENET_BASE_ADDR
+#define CONFIG_FEC_XCV_TYPE		RGMII
+#define CONFIG_ETHPRIME			"FEC"
+#define CONFIG_FEC_MXC_PHYADDR		4
+#define CONFIG_PHYLIB
+#define CONFIG_PHY_ATHEROS
+
+/* Framebuffer */
+#define CONFIG_VIDEO
+#ifdef CONFIG_VIDEO
+#define CONFIG_VIDEO_IPUV3
+#define CONFIG_IPUV3_CLK		260000000
+#define CONFIG_CFB_CONSOLE
+#define CONFIG_CFB_CONSOLE_ANSI
+#define CONFIG_VIDEO_SW_CURSOR
+#define CONFIG_VGA_AS_SINGLE_DEVICE
+#define CONFIG_VIDEO_BMP_RLE8
+#define CONFIG_IMX_HDMI
+#define CONFIG_IMX_VIDEO_SKIP
+#define CONFIG_CMD_HDMIDETECT
+#endif
+
+/* PCI */
+#define CONFIG_CMD_PCI
+#ifdef CONFIG_CMD_PCI
+#define CONFIG_PCI
+#define CONFIG_PCI_PNP
+#define CONFIG_PCI_SCAN_SHOW
+#define CONFIG_PCIE_IMX
+#define CONFIG_PCIE_IMX_PERST_GPIO	IMX_GPIO_NR(7, 12)
+#endif
+
+/* SATA */
+#define CONFIG_CMD_SATA
+#ifdef CONFIG_CMD_SATA
+#define CONFIG_DWC_AHSATA
+#define CONFIG_SYS_SATA_MAX_DEVICE	1
+#define CONFIG_DWC_AHSATA_PORT_ID	0
+#define CONFIG_DWC_AHSATA_BASE_ADDR	SATA_ARB_BASE_ADDR
+#define CONFIG_LBA48
+#define CONFIG_LIBATA
+#endif
+
+/* USB */
+#define CONFIG_CMD_USB
+#ifdef CONFIG_CMD_USB
+#define CONFIG_USB_EHCI
+#define CONFIG_USB_EHCI_MX6
+#define CONFIG_USB_MAX_CONTROLLER_COUNT 2
+#define CONFIG_MXC_USB_PORTSC		(PORT_PTS_UTMI | PORT_PTS_PTW)
+#define CONFIG_USB_STORAGE
+#define CONFIG_USB_KEYBOARD
+#ifdef CONFIG_USB_KEYBOARD
+#define CONFIG_SYS_USB_EVENT_POLL
+#define CONFIG_SYS_STDIO_DEREGISTER
+#define CONFIG_PREBOOT "if hdmidet; then usb start; fi"
+#endif /* CONFIG_USB_KEYBOARD */
+#endif /* CONFIG_CMD_USB      */
+
+/* RTC */
+#define CONFIG_CMD_DATE
+#ifdef CONFIG_CMD_DATE
+#define CONFIG_CMD_I2C
+#define CONFIG_RTC_DS1307
+#define CONFIG_SYS_RTC_BUS_NUM		2
+#endif
+
+/* I2C */
+#define CONFIG_CMD_I2C
+#ifdef CONFIG_CMD_I2C
+#define CONFIG_SYS_I2C
+#define CONFIG_SYS_I2C_MXC
+#define CONFIG_SYS_I2C_SPEED		100000
+#define CONFIG_I2C_EDID
+#endif
+
+/* Fuses */
+#define CONFIG_CMD_FUSE
+#ifdef CONFIG_CMD_FUSE
+#define CONFIG_MXC_OCOTP
+#endif
+
+#ifndef CONFIG_SYS_DCACHE_OFF
+#define CONFIG_CMD_CACHE
+#endif
+
+/* Flash and environment organization */
+#define CONFIG_SYS_NO_FLASH
+
+#define CONFIG_ENV_IS_IN_MMC
+#define CONFIG_SYS_MMC_ENV_DEV		2
+#define CONFIG_SYS_MMC_ENV_PART		1
+#define CONFIG_ENV_SIZE			(8 * 1024)
+#define CONFIG_ENV_OFFSET		(384 * 1024)
+#define CONFIG_ENV_OVERWRITE
+
+#define CONFIG_EXTRA_ENV_SETTINGS \
+	"bootargs_mmc1=console=ttymxc0,115200 di0_primary console=tty1\0" \
+	"bootargs_mmc2=video=mxcfb0:dev=hdmi,1920x1080M@60 " \
+			"video=mxcfb1:off video=mxcfb2:off fbmem=28M\0" \
+	"bootargs_mmc3=root=/dev/mmcblk0p1 rootwait consoleblank=0 quiet\0" \
+	"bootargs_mmc=setenv bootargs ${bootargs_mmc1} ${bootargs_mmc2} " \
+			"${bootargs_mmc3}\0" \
+	"bootargs_upd=setenv bootargs console=ttymxc0,115200 " \
+			"rdinit=/sbin/init enable_wait_mode=off\0" \
+	"bootcmd_mmc=run bootargs_mmc; mmc dev 2; " \
+			"mmc read 0x10800000 0x800 0x4000; bootm\0" \
+	"bootcmd_up1=load mmc 1 0x10800000 uImage\0" \
+	"bootcmd_up2=load mmc 1 0x10d00000 uramdisk.img; " \
+			"run bootargs_upd; " \
+			"bootm 0x10800000 0x10d00000\0" \
+	"console=ttymxc0\0" \
+	"fan=gpio set 92\0" \
+	"stdin=serial,usbkbd\0" \
+	"stdout=serial,vga\0" \
+	"stderr=serial,vga\0"
+
+#define CONFIG_BOOTCOMMAND \
+	"mmc rescan; " \
+	"if run bootcmd_up1; then " \
+		"run bootcmd_up2; " \
+	"else " \
+		"run bootcmd_mmc; " \
+	"fi"
+
+#endif			       /* __TBS2910_CONFIG_H * */