X-Git-Url: http://review.tizen.org/git/?p=platform%2Fkernel%2Fu-boot.git;a=blobdiff_plain;f=include%2Fconfigs%2Fsbc8349.h;h=2516a3e97e335cff14732439afc72e35d4c9d162;hp=cca596d43a4ada232a1d487c908fa5f5fb5d0088;hb=HEAD;hpb=f0e236c8d6646f6ef0ebf8f043962a07dda3b3a3

diff --git a/include/configs/sbc8349.h b/include/configs/sbc8349.h
deleted file mode 100644
index cca596d..0000000
--- a/include/configs/sbc8349.h
+++ /dev/null
@@ -1,324 +0,0 @@
-/* SPDX-License-Identifier: GPL-2.0+ */
-/*
- * WindRiver SBC8349 U-Boot configuration file.
- * Copyright (c) 2006, 2007 Wind River Systems, Inc.
- *
- * Paul Gortmaker <paul.gortmaker@windriver.com>
- * Based on the MPC8349EMDS config.
- */
-
-/*
- * sbc8349 board configuration file.
- */
-
-#ifndef __CONFIG_H
-#define __CONFIG_H
-
-/*
- * High Level Configuration Options
- */
-#define CONFIG_E300		1	/* E300 Family */
-
-/* Don't enable PCI2 on sbc834x - it doesn't exist physically. */
-#undef CONFIG_MPC83XX_PCI2		/* support for 2nd PCI controller */
-
-#undef CONFIG_SYS_DRAM_TEST		/* memory test, takes time */
-
-/*
- * DDR Setup
- */
-#undef CONFIG_DDR_ECC			/* only for ECC DDR module */
-#undef CONFIG_DDR_ECC_CMD		/* use DDR ECC user commands */
-#define CONFIG_SPD_EEPROM		/* use SPD EEPROM for DDR setup*/
-#define CONFIG_SYS_83XX_DDR_USES_CS0	/* WRS; Fsl board uses CS2/CS3 */
-
-/*
- * 32-bit data path mode.
- *
- * Please note that using this mode for devices with the real density of 64-bit
- * effectively reduces the amount of available memory due to the effect of
- * wrapping around while translating address to row/columns, for example in the
- * 256MB module the upper 128MB get aliased with contents of the lower
- * 128MB); normally this define should be used for devices with real 32-bit
- * data path.
- */
-#undef CONFIG_DDR_32BIT
-
-#define CONFIG_SYS_SDRAM_BASE		0x00000000 /* DDR is system memory*/
-#define CONFIG_SYS_DDR_SDRAM_CLK_CNTL	(DDR_SDRAM_CLK_CNTL_SS_EN | \
-				DDR_SDRAM_CLK_CNTL_CLK_ADJUST_075)
-#define CONFIG_DDR_2T_TIMING
-
-#if defined(CONFIG_SPD_EEPROM)
-/*
- * Determine DDR configuration from I2C interface.
- */
-#define SPD_EEPROM_ADDRESS	0x52		/* DDR DIMM */
-
-#else
-/*
- * Manually set up DDR parameters
- * NB: manual DDR setup untested on sbc834x
- */
-#define CONFIG_SYS_DDR_SIZE		256		/* MB */
-#define CONFIG_SYS_DDR_CS2_CONFIG	(CSCONFIG_EN \
-					| CSCONFIG_ROW_BIT_13 \
-					| CSCONFIG_COL_BIT_10)
-#define CONFIG_SYS_DDR_TIMING_1	0x36332321
-#define CONFIG_SYS_DDR_TIMING_2	0x00000800	/* P9-45,may need tuning */
-#define CONFIG_SYS_DDR_CONTROL	0xc2000000	/* unbuffered,no DYN_PWR */
-#define CONFIG_SYS_DDR_INTERVAL	0x04060100	/* autocharge,no open page */
-
-#if defined(CONFIG_DDR_32BIT)
-/* set burst length to 8 for 32-bit data path */
-				/* DLL,normal,seq,4/2.5, 8 burst len */
-#define CONFIG_SYS_DDR_MODE	0x00000023
-#else
-/* the default burst length is 4 - for 64-bit data path */
-				/* DLL,normal,seq,4/2.5, 4 burst len */
-#define CONFIG_SYS_DDR_MODE	0x00000022
-#endif
-#endif
-
-/*
- * SDRAM on the Local Bus
- */
-#define CONFIG_SYS_LBC_SDRAM_BASE	0xF0000000	/* Localbus SDRAM */
-#define CONFIG_SYS_LBC_SDRAM_SIZE	64		/* LBC SDRAM is 64MB */
-
-/*
- * FLASH on the Local Bus
- */
-#define CONFIG_SYS_FLASH_BASE		0xFF800000	/* start of FLASH   */
-#define CONFIG_SYS_FLASH_SIZE		8		/* flash size in MB */
-
-
-#define CONFIG_SYS_MAX_FLASH_BANKS	1	/* number of banks */
-#define CONFIG_SYS_MAX_FLASH_SECT	64	/* sectors per device */
-
-#undef CONFIG_SYS_FLASH_CHECKSUM
-#define CONFIG_SYS_FLASH_ERASE_TOUT	60000	/* Flash Erase Timeout (ms) */
-#define CONFIG_SYS_FLASH_WRITE_TOUT	500	/* Flash Write Timeout (ms) */
-
-#define CONFIG_SYS_MONITOR_BASE	CONFIG_SYS_TEXT_BASE	/* start of monitor */
-
-#if (CONFIG_SYS_MONITOR_BASE < CONFIG_SYS_FLASH_BASE)
-#define CONFIG_SYS_RAMBOOT
-#else
-#undef  CONFIG_SYS_RAMBOOT
-#endif
-
-#define CONFIG_SYS_INIT_RAM_LOCK	1
-					/* Initial RAM address */
-#define CONFIG_SYS_INIT_RAM_ADDR	0xFD000000
-					/* Size of used area in RAM*/
-#define CONFIG_SYS_INIT_RAM_SIZE	0x1000
-
-#define CONFIG_SYS_GBL_DATA_OFFSET	\
-			(CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
-#define CONFIG_SYS_INIT_SP_OFFSET	CONFIG_SYS_GBL_DATA_OFFSET
-
-#define CONFIG_SYS_MONITOR_LEN	(256 * 1024)	/* Reserve 256 kB for Mon */
-#define CONFIG_SYS_MALLOC_LEN	(256 * 1024)	/* Reserved for malloc */
-
-#undef CONFIG_SYS_LB_SDRAM	/* if board has SDRAM on local bus */
-
-/*
- * Serial Port
- */
-#define CONFIG_SYS_NS16550_SERIAL
-#define CONFIG_SYS_NS16550_REG_SIZE    1
-#define CONFIG_SYS_NS16550_CLK		get_bus_freq(0)
-
-#define CONFIG_SYS_BAUDRATE_TABLE  \
-		{300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 115200}
-
-#define CONFIG_SYS_NS16550_COM1        (CONFIG_SYS_IMMR+0x4500)
-#define CONFIG_SYS_NS16550_COM2        (CONFIG_SYS_IMMR+0x4600)
-
-/* I2C */
-#define CONFIG_SYS_I2C
-#define CONFIG_SYS_I2C_FSL
-#define CONFIG_SYS_FSL_I2C_SPEED	400000
-#define CONFIG_SYS_FSL_I2C_SLAVE	0x7F
-#define CONFIG_SYS_FSL_I2C_OFFSET	0x3000
-#define CONFIG_SYS_FSL_I2C2_SPEED	400000
-#define CONFIG_SYS_FSL_I2C2_SLAVE	0x7F
-#define CONFIG_SYS_FSL_I2C2_OFFSET	0x3100
-#define CONFIG_SYS_I2C_NOPROBES		{ {0, 0x69}, {1, 0x69} }
-/* could also use CONFIG_I2C_MULTI_BUS and CONFIG_SYS_SPD_BUS_NUM... */
-
-/* TSEC */
-#define CONFIG_SYS_TSEC1_OFFSET 0x24000
-#define CONFIG_SYS_TSEC1	(CONFIG_SYS_IMMR+CONFIG_SYS_TSEC1_OFFSET)
-#define CONFIG_SYS_TSEC2_OFFSET 0x25000
-#define CONFIG_SYS_TSEC2	(CONFIG_SYS_IMMR+CONFIG_SYS_TSEC2_OFFSET)
-
-/*
- * General PCI
- * Addresses are mapped 1-1.
- */
-#define CONFIG_SYS_PCI1_MEM_BASE	0x80000000
-#define CONFIG_SYS_PCI1_MEM_PHYS	CONFIG_SYS_PCI1_MEM_BASE
-#define CONFIG_SYS_PCI1_MEM_SIZE	0x10000000	/* 256M */
-#define CONFIG_SYS_PCI1_MMIO_BASE	0x90000000
-#define CONFIG_SYS_PCI1_MMIO_PHYS	CONFIG_SYS_PCI1_MMIO_BASE
-#define CONFIG_SYS_PCI1_MMIO_SIZE	0x10000000	/* 256M */
-#define CONFIG_SYS_PCI1_IO_BASE		0x00000000
-#define CONFIG_SYS_PCI1_IO_PHYS		0xE2000000
-#define CONFIG_SYS_PCI1_IO_SIZE		0x00100000	/* 1M */
-
-#define CONFIG_SYS_PCI2_MEM_BASE	0xA0000000
-#define CONFIG_SYS_PCI2_MEM_PHYS	CONFIG_SYS_PCI2_MEM_BASE
-#define CONFIG_SYS_PCI2_MEM_SIZE	0x10000000	/* 256M */
-#define CONFIG_SYS_PCI2_MMIO_BASE	0xB0000000
-#define CONFIG_SYS_PCI2_MMIO_PHYS	CONFIG_SYS_PCI2_MMIO_BASE
-#define CONFIG_SYS_PCI2_MMIO_SIZE	0x10000000	/* 256M */
-#define CONFIG_SYS_PCI2_IO_BASE		0x00000000
-#define CONFIG_SYS_PCI2_IO_PHYS		0xE2100000
-#define CONFIG_SYS_PCI2_IO_SIZE		0x00100000	/* 1M */
-
-#if defined(CONFIG_PCI)
-
-#undef CONFIG_TULIP
-
-#if !defined(CONFIG_PCI_PNP)
-	#define PCI_ENET0_IOADDR	0xFIXME
-	#define PCI_ENET0_MEMADDR	0xFIXME
-	#define PCI_IDSEL_NUMBER	0xFIXME
-#endif
-
-#undef CONFIG_PCI_SCAN_SHOW		/* show pci devices on startup */
-#define CONFIG_SYS_PCI_SUBSYS_VENDORID 0x1057  /* Motorola */
-
-#endif	/* CONFIG_PCI */
-
-/*
- * TSEC configuration
- */
-
-#if defined(CONFIG_TSEC_ENET)
-
-#define CONFIG_TSEC1	1
-#define CONFIG_TSEC1_NAME	"TSEC0"
-#define CONFIG_TSEC2	1
-#define CONFIG_TSEC2_NAME	"TSEC1"
-#define CONFIG_PHY_BCM5421S	1
-#define TSEC1_PHY_ADDR		0x19
-#define TSEC2_PHY_ADDR		0x1a
-#define TSEC1_PHYIDX		0
-#define TSEC2_PHYIDX		0
-#define TSEC1_FLAGS		TSEC_GIGABIT
-#define TSEC2_FLAGS		TSEC_GIGABIT
-
-/* Options are: TSEC[0-1] */
-#define CONFIG_ETHPRIME		"TSEC0"
-
-#endif	/* CONFIG_TSEC_ENET */
-
-/*
- * Environment
- */
-#ifndef CONFIG_SYS_RAMBOOT
-/* Address and size of Redundant Environment Sector	*/
-#endif
-
-#define CONFIG_LOADS_ECHO	1	/* echo on for serial download */
-#define CONFIG_SYS_LOADS_BAUD_CHANGE	1	/* allow baudrate change */
-
-/*
- * BOOTP options
- */
-#define CONFIG_BOOTP_BOOTFILESIZE
-
-#undef CONFIG_WATCHDOG			/* watchdog disabled */
-
-/*
- * Miscellaneous configurable options
- */
-#define CONFIG_SYS_LOAD_ADDR	0x2000000	/* default load address */
-
-/*
- * For booting Linux, the board info and command line data
- * have to be in the first 256 MB of memory, since this is
- * the maximum mapped by the Linux kernel during initialization.
- */
-				/* Initial Memory map for Linux*/
-#define CONFIG_SYS_BOOTMAPSZ	(256 << 20)
-
-#define CONFIG_SYS_RCWH_PCIHOST 0x80000000 /* PCIHOST  */
-
-/* System IO Config */
-#define CONFIG_SYS_SICRH 0
-#define CONFIG_SYS_SICRL SICRL_LDP_A
-
-#ifdef CONFIG_PCI
-#define CONFIG_PCI_INDIRECT_BRIDGE
-#endif
-
-#if defined(CONFIG_CMD_KGDB)
-#define CONFIG_KGDB_BAUDRATE	230400	/* speed of kgdb serial port */
-#endif
-
-/*
- * Environment Configuration
- */
-#define CONFIG_ENV_OVERWRITE
-
-#if defined(CONFIG_TSEC_ENET)
-#define CONFIG_HAS_ETH0
-#define CONFIG_HAS_ETH1
-#endif
-
-#define CONFIG_HOSTNAME		"SBC8349"
-#define CONFIG_ROOTPATH		"/tftpboot/rootfs"
-#define CONFIG_BOOTFILE		"uImage"
-
-				/* default location for tftp and bootm */
-#define CONFIG_LOADADDR		800000
-
-#define	CONFIG_EXTRA_ENV_SETTINGS					\
-	"netdev=eth0\0"							\
-	"hostname=sbc8349\0"						\
-	"nfsargs=setenv bootargs root=/dev/nfs rw "			\
-		"nfsroot=${serverip}:${rootpath}\0"			\
-	"ramargs=setenv bootargs root=/dev/ram rw\0"			\
-	"addip=setenv bootargs ${bootargs} "				\
-		"ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}"	\
-		":${hostname}:${netdev}:off panic=1\0"			\
-	"addtty=setenv bootargs ${bootargs} console=ttyS0,${baudrate}\0"\
-	"flash_nfs=run nfsargs addip addtty;"				\
-		"bootm ${kernel_addr}\0"				\
-	"flash_self=run ramargs addip addtty;"				\
-		"bootm ${kernel_addr} ${ramdisk_addr}\0"		\
-	"net_nfs=tftp 200000 ${bootfile};run nfsargs addip addtty;"	\
-		"bootm\0"						\
-	"load=tftp 100000 /tftpboot/sbc8349/u-boot.bin\0"		\
-	"update=protect off ff800000 ff83ffff; "			\
-		"era ff800000 ff83ffff; cp.b 100000 ff800000 ${filesize}\0" \
-	"upd=run load update\0"						\
-	"fdtaddr=780000\0"						\
-	"fdtfile=sbc8349.dtb\0"						\
-	""
-
-#define CONFIG_NFSBOOTCOMMAND						\
-	"setenv bootargs root=/dev/nfs rw "				\
-		"nfsroot=$serverip:$rootpath "				\
-		"ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:"	\
-							"$netdev:off "	\
-		"console=$consoledev,$baudrate $othbootargs;"		\
-	"tftp $loadaddr $bootfile;"					\
-	"tftp $fdtaddr $fdtfile;"					\
-	"bootm $loadaddr - $fdtaddr"
-
-#define CONFIG_RAMBOOTCOMMAND						\
-	"setenv bootargs root=/dev/ram rw "				\
-		"console=$consoledev,$baudrate $othbootargs;"		\
-	"tftp $ramdiskaddr $ramdiskfile;"				\
-	"tftp $loadaddr $bootfile;"					\
-	"tftp $fdtaddr $fdtfile;"					\
-	"bootm $loadaddr $ramdiskaddr $fdtaddr"
-
-#define CONFIG_BOOTCOMMAND	"run flash_self"
-
-#endif	/* __CONFIG_H */