X-Git-Url: http://review.tizen.org/git/?p=platform%2Fkernel%2Fu-boot.git;a=blobdiff_plain;f=include%2Fconfigs%2Fp1_twr.h;h=911203d85c17aad983ab51421cab3ba01b8ab7e7;hp=6dc5039560ec99cb315f1214aa7d2e51ca1c5929;hb=HEAD;hpb=6864fc8704661878294d1f0f981f47e864ef470f

diff --git a/include/configs/p1_twr.h b/include/configs/p1_twr.h
deleted file mode 100644
index 6dc5039..0000000
--- a/include/configs/p1_twr.h
+++ /dev/null
@@ -1,481 +0,0 @@
-/* SPDX-License-Identifier: GPL-2.0+ */
-/*
- * Copyright 2013 Freescale Semiconductor, Inc.
- */
-
-/*
- * QorIQ P1 Tower boards configuration file
- */
-#ifndef __CONFIG_H
-#define __CONFIG_H
-
-#if defined(CONFIG_TWR_P1025)
-#define CONFIG_BOARDNAME "TWR-P1025"
-#define CONFIG_SYS_LBC_LBCR	0x00080000	/* Conversion of LBC addr */
-#define CONFIG_SYS_LBC_LCRR	0x80000002	/* LB clock ratio reg */
-#endif
-
-#ifdef CONFIG_SDCARD
-#define CONFIG_RAMBOOT_SDCARD
-#define CONFIG_SYS_RAMBOOT
-#define CONFIG_RESET_VECTOR_ADDRESS	0x110bfffc
-#endif
-
-#ifndef CONFIG_RESET_VECTOR_ADDRESS
-#define CONFIG_RESET_VECTOR_ADDRESS	0xeffffffc
-#endif
-
-#ifndef CONFIG_SYS_MONITOR_BASE
-#define CONFIG_SYS_MONITOR_BASE	CONFIG_SYS_TEXT_BASE	/* start of monitor */
-#endif
-
-#define CONFIG_PCIE1	/* PCIE controller 1 (slot 1) */
-#define CONFIG_PCIE2	/* PCIE controller 2 (slot 2) */
-#define CONFIG_FSL_PCI_INIT	/* Use common FSL init code */
-#define CONFIG_PCI_INDIRECT_BRIDGE	/* indirect PCI bridge support */
-#define CONFIG_SYS_PCI_64BIT	/* enable 64-bit PCI resources */
-
-#define CONFIG_ENV_OVERWRITE
-
-#define CONFIG_SYS_SATA_MAX_DEVICE	2
-#define CONFIG_LBA48
-
-#ifndef __ASSEMBLY__
-extern unsigned long get_board_sys_clk(unsigned long dummy);
-#endif
-#define CONFIG_SYS_CLK_FREQ	get_board_sys_clk(0) /*sysclk for TWR-P1025 */
-
-#define CONFIG_DDR_CLK_FREQ	66666666
-
-#define CONFIG_HWCONFIG
-/*
- * These can be toggled for performance analysis, otherwise use default.
- */
-#define CONFIG_L2_CACHE
-#define CONFIG_BTB
-
-#define CONFIG_SYS_MEMTEST_START	0x00200000	/* memtest works on */
-#define CONFIG_SYS_MEMTEST_END		0x1fffffff
-
-#define CONFIG_SYS_CCSRBAR		0xffe00000
-#define CONFIG_SYS_CCSRBAR_PHYS_LOW	CONFIG_SYS_CCSRBAR
-
-/* DDR Setup */
-
-#define CONFIG_SYS_SDRAM_SIZE_LAW	LAW_SIZE_512M
-#define CONFIG_CHIP_SELECTS_PER_CTRL	1
-
-#define CONFIG_SYS_SDRAM_SIZE		(1u << (CONFIG_SYS_SDRAM_SIZE_LAW - 19))
-#define CONFIG_SYS_DDR_SDRAM_BASE	0x00000000
-#define CONFIG_SYS_SDRAM_BASE		CONFIG_SYS_DDR_SDRAM_BASE
-
-#define CONFIG_DIMM_SLOTS_PER_CTLR	1
-
-/* Default settings for DDR3 */
-#define CONFIG_SYS_DDR_CS0_BNDS		0x0000001f
-#define CONFIG_SYS_DDR_CS0_CONFIG	0x80014202
-#define CONFIG_SYS_DDR_CS0_CONFIG_2	0x00000000
-#define CONFIG_SYS_DDR_CS1_BNDS		0x00000000
-#define CONFIG_SYS_DDR_CS1_CONFIG	0x00000000
-#define CONFIG_SYS_DDR_CS1_CONFIG_2	0x00000000
-
-#define CONFIG_SYS_DDR_DATA_INIT	0xdeadbeef
-#define CONFIG_SYS_DDR_INIT_ADDR	0x00000000
-#define CONFIG_SYS_DDR_INIT_EXT_ADDR	0x00000000
-#define CONFIG_SYS_DDR_MODE_CONTROL	0x00000000
-
-#define CONFIG_SYS_DDR_ZQ_CONTROL	0x89080600
-#define CONFIG_SYS_DDR_WRLVL_CONTROL	0x8655a608
-#define CONFIG_SYS_DDR_SR_CNTR		0x00000000
-#define CONFIG_SYS_DDR_RCW_1		0x00000000
-#define CONFIG_SYS_DDR_RCW_2		0x00000000
-#define CONFIG_SYS_DDR_CONTROL		0xc70c0000	/* Type = DDR3	*/
-#define CONFIG_SYS_DDR_CONTROL_2	0x04401050
-#define CONFIG_SYS_DDR_TIMING_4		0x00220001
-#define CONFIG_SYS_DDR_TIMING_5		0x03402400
-
-#define CONFIG_SYS_DDR_TIMING_3		0x00020000
-#define CONFIG_SYS_DDR_TIMING_0		0x00220004
-#define CONFIG_SYS_DDR_TIMING_1		0x5c5b6544
-#define CONFIG_SYS_DDR_TIMING_2		0x0fa880de
-#define CONFIG_SYS_DDR_CLK_CTRL		0x03000000
-#define CONFIG_SYS_DDR_MODE_1		0x80461320
-#define CONFIG_SYS_DDR_MODE_2		0x00008000
-#define CONFIG_SYS_DDR_INTERVAL		0x09480000
-
-/*
- * Memory map
- *
- * 0x0000_0000 0x1fff_ffff	DDR		Up to 512MB cacheable
- * 0x8000_0000 0xdfff_ffff	PCI Express Mem	1.5G non-cacheable(PCIe * 3)
- * 0xffc0_0000 0xffc3_ffff	PCI IO range	256k non-cacheable
- *
- * Localbus
- * 0xe000_0000 0xe002_0000	SSD1289		128K non-cacheable
- * 0xec00_0000 0xefff_ffff	FLASH		Up to 64M non-cacheable
- *
- * 0xff90_0000 0xff97_ffff	L2 SRAM		Up to 512K cacheable
- * 0xffd0_0000 0xffd0_3fff	init ram	16K Cacheable
- * 0xffe0_0000 0xffef_ffff	CCSR		1M non-cacheable
- */
-
-/*
- * Local Bus Definitions
- */
-#define CONFIG_SYS_MAX_FLASH_SECT	512	/* 64M */
-#define CONFIG_SYS_FLASH_BASE		0xec000000
-
-#define CONFIG_SYS_FLASH_BASE_PHYS	CONFIG_SYS_FLASH_BASE
-
-#define CONFIG_FLASH_BR_PRELIM (BR_PHYS_ADDR((CONFIG_SYS_FLASH_BASE_PHYS)) \
-	| BR_PS_16 | BR_V)
-
-#define CONFIG_FLASH_OR_PRELIM	0xfc0000b1
-
-#define CONFIG_SYS_SSD_BASE	0xe0000000
-#define CONFIG_SYS_SSD_BASE_PHYS	CONFIG_SYS_SSD_BASE
-#define CONFIG_SSD_BR_PRELIM	(BR_PHYS_ADDR(CONFIG_SYS_SSD_BASE_PHYS) | \
-					BR_PS_16 | BR_V)
-#define CONFIG_SSD_OR_PRELIM	(OR_AM_64KB | OR_GPCM_CSNT | OR_GPCM_XACS | \
-				 OR_GPCM_ACS_DIV2 | OR_GPCM_SCY | \
-				 OR_GPCM_TRLX | OR_GPCM_EHTR | OR_GPCM_EAD)
-
-#define CONFIG_SYS_BR2_PRELIM CONFIG_SSD_BR_PRELIM
-#define CONFIG_SYS_OR2_PRELIM CONFIG_SSD_OR_PRELIM
-
-#define CONFIG_SYS_FLASH_BANKS_LIST	{CONFIG_SYS_FLASH_BASE_PHYS}
-#define CONFIG_SYS_FLASH_QUIET_TEST
-#define CONFIG_FLASH_SHOW_PROGRESS	45	/* count down from 45/5: 9..1 */
-
-#define CONFIG_SYS_MAX_FLASH_BANKS	1	/* number of banks */
-
-#undef CONFIG_SYS_FLASH_CHECKSUM
-#define CONFIG_SYS_FLASH_ERASE_TOUT	60000	/* Flash Erase Timeout (ms) */
-#define CONFIG_SYS_FLASH_WRITE_TOUT	500	/* Flash Write Timeout (ms) */
-
-#define CONFIG_SYS_FLASH_EMPTY_INFO
-
-#define CONFIG_SYS_INIT_RAM_LOCK
-#define CONFIG_SYS_INIT_RAM_ADDR	0xffd00000
-/* Initial L1 address */
-#define CONFIG_SYS_INIT_RAM_ADDR_PHYS	CONFIG_SYS_INIT_RAM_ADDR
-#define CONFIG_SYS_INIT_RAM_ADDR_PHYS_HIGH 0
-#define CONFIG_SYS_INIT_RAM_ADDR_PHYS_LOW CONFIG_SYS_INIT_RAM_ADDR_PHYS
-/* Size of used area in RAM */
-#define CONFIG_SYS_INIT_RAM_SIZE	0x00004000
-
-#define CONFIG_SYS_GBL_DATA_OFFSET	(CONFIG_SYS_INIT_RAM_SIZE - \
-					GENERATED_GBL_DATA_SIZE)
-#define CONFIG_SYS_INIT_SP_OFFSET	CONFIG_SYS_GBL_DATA_OFFSET
-
-#define CONFIG_SYS_MONITOR_LEN	(768 * 1024)
-#define CONFIG_SYS_MALLOC_LEN	(1024 * 1024)/* Reserved for malloc */
-
-#define CONFIG_SYS_BR0_PRELIM	CONFIG_FLASH_BR_PRELIM	/* NOR Base Address */
-#define CONFIG_SYS_OR0_PRELIM	CONFIG_FLASH_OR_PRELIM	/* NOR Options */
-
-/* Serial Port
- * open - index 2
- * shorted - index 1
- */
-#undef CONFIG_SERIAL_SOFTWARE_FIFO
-#define CONFIG_SYS_NS16550_SERIAL
-#define CONFIG_SYS_NS16550_REG_SIZE	1
-#define CONFIG_SYS_NS16550_CLK		get_bus_freq(0)
-
-#define CONFIG_SYS_BAUDRATE_TABLE	\
-	{300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200}
-
-#define CONFIG_SYS_NS16550_COM1	(CONFIG_SYS_CCSRBAR+0x4500)
-#define CONFIG_SYS_NS16550_COM2	(CONFIG_SYS_CCSRBAR+0x4600)
-
-/* I2C */
-#define CONFIG_SYS_I2C
-#define CONFIG_SYS_I2C_FSL			/* Use FSL common I2C driver */
-#define CONFIG_SYS_FSL_I2C_SPEED	400000	/* I2C spd and slave address */
-#define CONFIG_SYS_FSL_I2C_SLAVE	0x7F
-#define CONFIG_SYS_FSL_I2C_OFFSET	0x3000
-#define CONFIG_SYS_I2C_EEPROM_ADDR	0x52
-
-/*
- * I2C2 EEPROM
- */
-#define CONFIG_SYS_FSL_I2C2_SPEED	400000	/* I2C spd and slave address */
-#define CONFIG_SYS_FSL_I2C2_SLAVE	0x7F
-#define CONFIG_SYS_FSL_I2C2_OFFSET	0x3100
-
-#define CONFIG_SYS_I2C_PCA9555_ADDR	0x23
-
-/* enable read and write access to EEPROM */
-#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1
-#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 3
-#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 5
-
-#if defined(CONFIG_PCI)
-/*
- * General PCI
- * Memory space is mapped 1-1, but I/O space must start from 0.
- */
-
-/* controller 2, direct to uli, tgtid 2, Base address 9000 */
-#define CONFIG_SYS_PCIE2_NAME		"TWR-ELEV PCIe SLOT"
-#define CONFIG_SYS_PCIE2_MEM_VIRT	0xa0000000
-#define CONFIG_SYS_PCIE2_MEM_BUS	0xa0000000
-#define CONFIG_SYS_PCIE2_MEM_PHYS	0xa0000000
-#define CONFIG_SYS_PCIE2_MEM_SIZE	0x20000000	/* 512M */
-#define CONFIG_SYS_PCIE2_IO_VIRT	0xffc10000
-#define CONFIG_SYS_PCIE2_IO_BUS		0x00000000
-#define CONFIG_SYS_PCIE2_IO_PHYS	0xffc10000
-#define CONFIG_SYS_PCIE2_IO_SIZE	0x00010000	/* 64k */
-
-/* controller 1, tgtid 1, Base address a000 */
-#define CONFIG_SYS_PCIE1_NAME		"mini PCIe SLOT"
-#define CONFIG_SYS_PCIE1_MEM_VIRT	0x80000000
-#define CONFIG_SYS_PCIE1_MEM_BUS	0x80000000
-#define CONFIG_SYS_PCIE1_MEM_PHYS	0x80000000
-#define CONFIG_SYS_PCIE1_MEM_SIZE	0x20000000	/* 512M */
-#define CONFIG_SYS_PCIE1_IO_VIRT	0xffc00000
-#define CONFIG_SYS_PCIE1_IO_BUS		0x00000000
-#define CONFIG_SYS_PCIE1_IO_PHYS	0xffc00000
-#define CONFIG_SYS_PCIE1_IO_SIZE	0x00010000	/* 64k */
-
-#define CONFIG_PCI_SCAN_SHOW	/* show pci devices on startup */
-#endif /* CONFIG_PCI */
-
-#if defined(CONFIG_TSEC_ENET)
-
-#define CONFIG_TSEC1
-#define CONFIG_TSEC1_NAME	"eTSEC1"
-#undef CONFIG_TSEC2
-#undef CONFIG_TSEC2_NAME
-#define CONFIG_TSEC3
-#define CONFIG_TSEC3_NAME	"eTSEC3"
-
-#define TSEC1_PHY_ADDR	2
-#define TSEC2_PHY_ADDR	0
-#define TSEC3_PHY_ADDR	1
-
-#define TSEC1_FLAGS	(TSEC_GIGABIT | TSEC_REDUCED)
-#define TSEC2_FLAGS	(TSEC_GIGABIT | TSEC_REDUCED)
-#define TSEC3_FLAGS	(TSEC_GIGABIT | TSEC_REDUCED)
-
-#define TSEC1_PHYIDX	0
-#define TSEC2_PHYIDX	0
-#define TSEC3_PHYIDX	0
-
-#define CONFIG_ETHPRIME	"eTSEC1"
-
-#define CONFIG_HAS_ETH0
-#define CONFIG_HAS_ETH1
-#undef CONFIG_HAS_ETH2
-#endif /* CONFIG_TSEC_ENET */
-
-#ifdef CONFIG_QE
-/* QE microcode/firmware address */
-#define CONFIG_SYS_QE_FW_ADDR	0xefec0000
-#define CONFIG_SYS_QE_FMAN_FW_LENGTH	0x10000
-#endif /* CONFIG_QE */
-
-#ifdef CONFIG_TWR_P1025
-/*
- * QE UEC ethernet configuration
- */
-#define CONFIG_MIIM_ADDRESS	(CONFIG_SYS_CCSRBAR + 0x82120)
-
-#undef CONFIG_UEC_ETH
-#define CONFIG_PHY_MODE_NEED_CHANGE
-
-#define CONFIG_UEC_ETH1	/* ETH1 */
-#define CONFIG_HAS_ETH0
-
-#ifdef CONFIG_UEC_ETH1
-#define CONFIG_SYS_UEC1_UCC_NUM	0	/* UCC1 */
-#define CONFIG_SYS_UEC1_RX_CLK	QE_CLK12 /* CLK12 for MII */
-#define CONFIG_SYS_UEC1_TX_CLK	QE_CLK9 /* CLK9 for MII */
-#define CONFIG_SYS_UEC1_ETH_TYPE	FAST_ETH
-#define CONFIG_SYS_UEC1_PHY_ADDR	0x18	/* 0x18 for MII */
-#define CONFIG_SYS_UEC1_INTERFACE_TYPE PHY_INTERFACE_MODE_MII
-#define CONFIG_SYS_UEC1_INTERFACE_SPEED	100
-#endif /* CONFIG_UEC_ETH1 */
-
-#define CONFIG_UEC_ETH5	/* ETH5 */
-#define CONFIG_HAS_ETH1
-
-#ifdef CONFIG_UEC_ETH5
-#define CONFIG_SYS_UEC5_UCC_NUM	4	/* UCC5 */
-#define CONFIG_SYS_UEC5_RX_CLK	QE_CLK_NONE
-#define CONFIG_SYS_UEC5_TX_CLK	QE_CLK13 /* CLK 13 for RMII */
-#define CONFIG_SYS_UEC5_ETH_TYPE	FAST_ETH
-#define CONFIG_SYS_UEC5_PHY_ADDR	0x19	/* 0x19 for RMII */
-#define CONFIG_SYS_UEC5_INTERFACE_TYPE PHY_INTERFACE_MODE_RMII
-#define CONFIG_SYS_UEC5_INTERFACE_SPEED	100
-#endif /* CONFIG_UEC_ETH5 */
-#endif /* CONFIG_TWR-P1025 */
-
-/*
- * Dynamic MTD Partition support with mtdparts
- */
-
-/*
- * Environment
- */
-#ifdef CONFIG_SYS_RAMBOOT
-#ifdef CONFIG_RAMBOOT_SDCARD
-#define CONFIG_SYS_MMC_ENV_DEV	0
-#endif
-#endif
-
-#define CONFIG_LOADS_ECHO		/* echo on for serial download */
-#define CONFIG_SYS_LOADS_BAUD_CHANGE	/* allow baudrate change */
-
-/*
- * USB
- */
-#define CONFIG_HAS_FSL_DR_USB
-
-#if defined(CONFIG_HAS_FSL_DR_USB)
-#ifdef CONFIG_USB_EHCI_HCD
-#define CONFIG_EHCI_HCD_INIT_AFTER_RESET
-#define CONFIG_USB_EHCI_FSL
-#endif
-#endif
-
-#ifdef CONFIG_MMC
-#define CONFIG_SYS_FSL_ESDHC_ADDR	CONFIG_SYS_MPC85xx_ESDHC_ADDR
-#endif
-
-#undef CONFIG_WATCHDOG	/* watchdog disabled */
-
-/*
- * Miscellaneous configurable options
- */
-#define CONFIG_SYS_LOAD_ADDR	0x2000000	/* default load address */
-
-/*
- * For booting Linux, the board info and command line data
- * have to be in the first 64 MB of memory, since this is
- * the maximum mapped by the Linux kernel during initialization.
- */
-#define CONFIG_SYS_BOOTMAPSZ	(64 << 20)	/* Initial Memory for Linux*/
-#define CONFIG_SYS_BOOTM_LEN	(64 << 20)	/* Increase max gunzip size */
-
-/*
- * Environment Configuration
- */
-#define CONFIG_HOSTNAME		"unknown"
-#define CONFIG_ROOTPATH		"/opt/nfsroot"
-#define CONFIG_BOOTFILE		"uImage"
-#define CONFIG_UBOOTPATH	u-boot.bin /* U-Boot image on TFTP server */
-
-/* default location for tftp and bootm */
-#define CONFIG_LOADADDR	1000000
-
-#define	CONFIG_EXTRA_ENV_SETTINGS	\
-"netdev=eth0\0"	\
-"uboot=" __stringify(CONFIG_UBOOTPATH) "\0"	\
-"loadaddr=1000000\0"	\
-"bootfile=uImage\0"	\
-"dtbfile=twr-p1025twr.dtb\0"	\
-"ramdiskfile=rootfs.ext2.gz.uboot\0"	\
-"qefirmwarefile=fsl_qe_ucode_1021_10_A.bin\0"	\
-"tftpflash=tftpboot $loadaddr $uboot; "	\
-	"protect off " __stringify(CONFIG_SYS_TEXT_BASE) " +$filesize; " \
-	"erase " __stringify(CONFIG_SYS_TEXT_BASE) " +$filesize; "	\
-	"cp.b $loadaddr " __stringify(CONFIG_SYS_TEXT_BASE) " $filesize; " \
-	"protect on " __stringify(CONFIG_SYS_TEXT_BASE) " +$filesize; "	\
-	"cmp.b $loadaddr " __stringify(CONFIG_SYS_TEXT_BASE) " $filesize\0" \
-"kernelflash=tftpboot $loadaddr $bootfile; "	\
-	"protect off 0xefa80000 +$filesize; "	\
-	"erase 0xefa80000 +$filesize; "	\
-	"cp.b $loadaddr 0xefa80000 $filesize; "	\
-	"protect on 0xefa80000 +$filesize; "	\
-	"cmp.b $loadaddr 0xefa80000 $filesize\0"	\
-"dtbflash=tftpboot $loadaddr $dtbfile; "	\
-	"protect off 0xefe80000 +$filesize; "	\
-	"erase 0xefe80000 +$filesize; "	\
-	"cp.b $loadaddr 0xefe80000 $filesize; "	\
-	"protect on 0xefe80000 +$filesize; "	\
-	"cmp.b $loadaddr 0xefe80000 $filesize\0"	\
-"ramdiskflash=tftpboot $loadaddr $ramdiskfile; "	\
-	"protect off 0xeeb80000 +$filesize; "	\
-	"erase 0xeeb80000 +$filesize; "	\
-	"cp.b $loadaddr 0xeeb80000 $filesize; "	\
-	"protect on 0xeeb80000 +$filesize; "	\
-	"cmp.b $loadaddr 0xeeb80000 $filesize\0"	\
-"qefirmwareflash=tftpboot $loadaddr $qefirmwarefile; "	\
-	"protect off 0xefec0000 +$filesize; "	\
-	"erase 0xefec0000 +$filesize; "	\
-	"cp.b $loadaddr 0xefec0000 $filesize; "	\
-	"protect on 0xefec0000 +$filesize; "	\
-	"cmp.b $loadaddr 0xefec0000 $filesize\0"	\
-"consoledev=ttyS0\0"	\
-"ramdiskaddr=2000000\0"	\
-"ramdiskfile=rootfs.ext2.gz.uboot\0"	\
-"fdtaddr=1e00000\0"	\
-"bdev=sda1\0"	\
-"norbootaddr=ef080000\0"	\
-"norfdtaddr=ef040000\0"	\
-"ramdisk_size=120000\0" \
-"usbboot=setenv bootargs root=/dev/sda1 rw rootdelay=5 " \
-"console=$consoledev,$baudrate $othbootargs ; bootm 0xefa80000 - 0xefe80000"
-
-#define CONFIG_NFSBOOTCOMMAND	\
-"setenv bootargs root=/dev/nfs rw "	\
-"nfsroot=$serverip:$rootpath "	\
-"ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:$netdev:off " \
-"console=$consoledev,$baudrate $othbootargs;" \
-"tftp $loadaddr $bootfile&&"	\
-"tftp $fdtaddr $fdtfile&&"	\
-"bootm $loadaddr - $fdtaddr"
-
-#define CONFIG_HDBOOT	\
-"setenv bootargs root=/dev/$bdev rw rootdelay=30 "	\
-"console=$consoledev,$baudrate $othbootargs;" \
-"usb start;"	\
-"ext2load usb 0:1 $loadaddr /boot/$bootfile;"	\
-"ext2load usb 0:1 $fdtaddr /boot/$fdtfile;"	\
-"bootm $loadaddr - $fdtaddr"
-
-#define CONFIG_USB_FAT_BOOT	\
-"setenv bootargs root=/dev/ram rw "	\
-"console=$consoledev,$baudrate $othbootargs " \
-"ramdisk_size=$ramdisk_size;"	\
-"usb start;"	\
-"fatload usb 0:2 $loadaddr $bootfile;"	\
-"fatload usb 0:2 $fdtaddr $fdtfile;"	\
-"fatload usb 0:2 $ramdiskaddr $ramdiskfile;"	\
-"bootm $loadaddr $ramdiskaddr $fdtaddr"
-
-#define CONFIG_USB_EXT2_BOOT	\
-"setenv bootargs root=/dev/ram rw "	\
-"console=$consoledev,$baudrate $othbootargs " \
-"ramdisk_size=$ramdisk_size;"	\
-"usb start;"	\
-"ext2load usb 0:4 $loadaddr $bootfile;"	\
-"ext2load usb 0:4 $fdtaddr $fdtfile;" \
-"ext2load usb 0:4 $ramdiskaddr $ramdiskfile;" \
-"bootm $loadaddr $ramdiskaddr $fdtaddr"
-
-#define CONFIG_NORBOOT	\
-"setenv bootargs root=/dev/mtdblock3 rw "	\
-"console=$consoledev,$baudrate rootfstype=jffs2 $othbootargs;"	\
-"bootm $norbootaddr - $norfdtaddr"
-
-#define CONFIG_RAMBOOTCOMMAND_TFTP	\
-"setenv bootargs root=/dev/ram rw "	\
-"console=$consoledev,$baudrate $othbootargs " \
-"ramdisk_size=$ramdisk_size;"	\
-"tftp $ramdiskaddr $ramdiskfile;"	\
-"tftp $loadaddr $bootfile;"	\
-"tftp $fdtaddr $fdtfile;"	\
-"bootm $loadaddr $ramdiskaddr $fdtaddr"
-
-#define CONFIG_RAMBOOTCOMMAND	\
-"setenv bootargs root=/dev/ram rw "	\
-"console=$consoledev,$baudrate $othbootargs " \
-"ramdisk_size=$ramdisk_size;"	\
-"bootm 0xefa80000 0xeeb80000 0xefe80000"
-
-#define CONFIG_BOOTCOMMAND	CONFIG_RAMBOOTCOMMAND
-
-#endif /* __CONFIG_H */