X-Git-Url: http://review.tizen.org/git/?p=platform%2Fkernel%2Fu-boot.git;a=blobdiff_plain;f=include%2Fconfigs%2Fgalaxy5200.h;h=b555d82ddc066d5c1554856ebddf2938585aed87;hp=560363d237a94cb26886991e5144709ddb89f729;hb=HEAD;hpb=d44a5f51288aec60c6bdb4ac939d75c24e5bf9c2 diff --git a/include/configs/galaxy5200.h b/include/configs/galaxy5200.h deleted file mode 100644 index 560363d..0000000 --- a/include/configs/galaxy5200.h +++ /dev/null @@ -1,432 +0,0 @@ -/* - * (C) Copyright 2003-2005 - * Wolfgang Denk, DENX Software Engineering, wd@denx.de. - * - * (C) Copyright 2006 - * Eric Schumann, Phytec Messatechnik GmbH - * - * (C) Copyright 2009 - * Jon Smirl - * - * (C) Copyright 2009 - * Eric Millbrandt, DEKA Research and Development Corporation - * - * SPDX-License-Identifier: GPL-2.0+ - */ - -#ifndef __CONFIG_H -#define __CONFIG_H - -#define CONFIG_BOARDINFO "galaxy5200" - -/* - * High Level Configuration Options - * (easy to change) - */ -#define CONFIG_MPC5xxx 1 /* This is an MPC5xxx CPU */ -#define CONFIG_MPC5200 1 /* (more precisely an MPC5200 CPU) */ -#define CONFIG_SYS_MPC5XXX_CLKIN 33333333 /* ... running at 33.333333MHz */ - -/* - * Valid values for CONFIG_SYS_TEXT_BASE are: - * 0xFFF00000 boot high (standard configuration) - * 0xFE000000 boot low - * 0x00100000 boot from RAM (for testing only) does not work - */ -#ifdef CONFIG_galaxy5200_LOWBOOT -#define CONFIG_SYS_TEXT_BASE 0xFE000000 -#endif - -#ifndef CONFIG_SYS_TEXT_BASE -#define CONFIG_SYS_TEXT_BASE 0xFFF00000 /* Standard: boot high */ -#endif - -/* - * Serial console configuration - */ -#define CONFIG_PSC_CONSOLE 4 /* console is on PSC4 -> */ - /* define gps port conf. */ - /* register later on to */ - /* enable UART function! */ -#define CONFIG_BAUDRATE 115200 /* ... at 115200 bps */ -#define CONFIG_SYS_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200, 230400 } - -/* - * Command line configuration. - */ -#include - -#define CONFIG_CMD_DATE -#define CONFIG_CMD_DHCP -#define CONFIG_CMD_EEPROM -#define CONFIG_CMD_I2C -#define CONFIG_CMD_JFFS2 -#define CONFIG_CMD_MII -#define CONFIG_CMD_NFS -#define CONFIG_CMD_SNTP -#define CONFIG_CMD_PING -#define CONFIG_CMD_ASKENV -#define CONFIG_CMD_USB -#define CONFIG_CMD_CACHE -#define CONFIG_CMD_FAT - -#define CONFIG_TIMESTAMP 1 /* Print image info with timestamp */ - -#if (CONFIG_SYS_TEXT_BASE == 0xFE000000) /* Boot low */ -#define CONFIG_SYS_LOWBOOT 1 -#endif -/* RAMBOOT will be defined automatically in memory section */ - -#define MTDIDS_DEFAULT "nor0=physmap-flash.0" -#define MTDPARTS_DEFAULT "mtdparts=physmap-flash.0:256k(ubootl)," \ - "1792k(kernel),13312k(jffs2),256k(uboot)ro,256k(oftree),-(space)" - -/* - * Autobooting - */ -#define CONFIG_BOOTDELAY 10 /* autoboot after 10 seconds */ -#define CONFIG_ZERO_BOOTDELAY_CHECK /* allow stopping of boot process */ - /* even with bootdelay=0 */ -#define CONFIG_BOOT_RETRY_TIME 120 /* Reset if no command is entered */ -#define CONFIG_RESET_TO_RETRY - -#define CONFIG_PREBOOT "echo;" \ - "echo Welcome to U-Boot;"\ - "echo" - -#define CONFIG_BOOTCOMMAND "go ff300004 0; go ff300004 2 2;" \ - "bootm ff040000 ff900000 fffc0000" -#define CONFIG_BOOTARGS "console=ttyPSC0,115200" -#define CONFIG_EXTRA_ENV_SETTINGS "epson=yes\0" - -/* - * IPB Bus clocking configuration. - */ -#define CONFIG_SYS_IPBCLK_EQUALS_XLBCLK /* define for 133MHz speed */ -#define CONFIG_SYS_XLB_PIPELINING 1 - -/* - * I2C configuration - */ -#define CONFIG_HARD_I2C 1 /* I2C with hardware support */ -#define CONFIG_SYS_I2C_MODULE 2 /* Select I2C module #1 or #2 */ -#define CONFIG_SYS_I2C_SPEED 100000 /* 100 kHz */ -#define CONFIG_SYS_I2C_SLAVE 0x7F -#define CONFIG_SYS_I2C_INIT_MPC5XXX /* Reset devices on i2c bus */ - -/* - * EEPROM CAT24WC32 configuration - */ -#define CONFIG_SYS_I2C_EEPROM_ADDR 0x52 /* 1010100x */ -#define CONFIG_SYS_I2C_FACT_ADDR 0x52 /* EEPROM CAT24WC32 */ -#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 2 /* Bytes of address */ -#define CONFIG_SYS_EEPROM_SIZE 4096 -#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 3 -#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 15 - -/* - * RTC configuration - */ -#define RTC -#define CONFIG_RTC_DS3231 1 -#define CONFIG_SYS_I2C_RTC_ADDR 0x68 - -/* - * Flash configuration - */ - -#define CONFIG_SYS_FLASH_BASE 0xfe000000 -/* - * The flash size is autoconfigured, but arch/powerpc/cpu/mpc5xxx/cpu_init.c needs this - * variable defined - */ -#define CONFIG_SYS_FLASH_SIZE 0x02000000 -#define CONFIG_SYS_FLASH_BANKS_LIST { CONFIG_SYS_FLASH_BASE } - -#define CONFIG_SYS_FLASH_CFI 1 /* Flash is CFI conformant */ -#define CONFIG_FLASH_CFI_DRIVER 1 /* Use the common driver */ -#define CONFIG_SYS_FLASH_EMPTY_INFO -#define CONFIG_SYS_MAX_FLASH_SECT 259 /* max num of sects on one chip */ -#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* max num of flash banks */ - /* (= chip selects) */ -#define CONFIG_SYS_FLASH_USE_BUFFER_WRITE - -/* - * Use hardware protection. This seems required, as the BDI uses hardware - * protection. Without this, U-Boot can't work with this sectors as its - * protection is software only by default. - */ -#define CONFIG_SYS_FLASH_PROTECTION 1 - -/* - * Environment settings - */ - -#define CONFIG_ENV_IS_IN_EEPROM 1 -#define CONFIG_ENV_OFFSET 0x00 /* environment starts at the */ - /* beginning of the EEPROM */ -#define CONFIG_ENV_SIZE CONFIG_SYS_EEPROM_SIZE - -#define CONFIG_ENV_OVERWRITE 1 - -/* - * SDRAM configuration - */ -#define SDRAM_DDR 1 -#define SDRAM_MODE 0x018D0000 -#define SDRAM_EMODE 0x40090000 -#define SDRAM_CONTROL 0x71500F00 -#define SDRAM_CONFIG1 0x73711930 -#define SDRAM_CONFIG2 0x47770000 - -/* - * Memory map - */ -#define CONFIG_SYS_MBAR 0xF0000000 /* MBAR has to be switched by other */ - /* bootloader or debugger config */ -#define CONFIG_SYS_SDRAM_BASE 0x00000000 -#define CONFIG_SYS_DEFAULT_MBAR 0x80000000 - -/* Use SRAM until RAM will be available */ -#define CONFIG_SYS_INIT_RAM_ADDR MPC5XXX_SRAM - -/* End of used area in SPRAM */ -#define CONFIG_SYS_INIT_RAM_SIZE MPC5XXX_SRAM_SIZE - -#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - \ - GENERATED_GBL_DATA_SIZE) -#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET - -#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE -#if (CONFIG_SYS_MONITOR_BASE < CONFIG_SYS_FLASH_BASE) -# define CONFIG_SYS_RAMBOOT 1 -#endif - -#define CONFIG_SYS_MONITOR_LEN (192 << 10) /* Reserve 192 kB for Monitor */ -#define CONFIG_SYS_MALLOC_LEN (128 << 10) /* Reserve 128 kB for malloc() */ -#define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */ - -/* Chip Select configuration for NAND flash */ -#define CONFIG_SYS_CS1_START 0x20000000 -#define CONFIG_SYS_CS1_SIZE 0x90000 -#define CONFIG_SYS_CS1_CFG 0x00025b00 - -/* Chip Select configuration for Epson S1D13513 */ -#define CONFIG_SYS_CS3_START 0x10000000 -#define CONFIG_SYS_CS3_SIZE 0x400000 -#define CONFIG_SYS_CS3_CFG 0xffff3d10 - -/* - * Ethernet configuration - */ -#define CONFIG_MPC5xxx_FEC 1 -#define CONFIG_MPC5xxx_FEC_MII100 -#define CONFIG_PHY_ADDR 0x01 -#define CONFIG_NO_AUTOLOAD 1 - -/* - * GPIO configuration - * - * GPS port configuration - * - * [29:31] = 01x - * AC97 on PSC1 - * PSC1_0 -> AC97 SDATA out - * PSC1_1 -> AC97 SDTA in - * PSC1_2 -> AC97 SYNC out - * PSC1_3 -> AC97 bitclock out - * PSC1_4 -> AC97 reset out - * - * [28] = Reserved - * - * [25:27] = 110 - * SPI on PSC2 - * PSC2_0 -> MOSI - * PSC2_1 -> MISO - * PSC2_2 -> n/a - * PSC2_3 -> CLK - * PSC2_4 -> SS - * - * [24] = Reserved - * - * [20:23] = 0001 - * USB on PSC3 - * PSC3_0 -> USB_OE OE out - * PSC3_1 -> USB_TXN Tx- out - * PSC3_2 -> USB_TXP Tx+ out - * PSC3_3 -> USB_TXD - * PSC3_4 -> USB_RXP Rx+ in - * PSC3_5 -> USB_RXN Rx- in - * PSC3_6 -> USB_PWR PortPower out - * PSC3_7 -> USB_SPEED speed out - * PSC3_8 -> USB_SUSPEND suspend - * PSC3_9 -> USB_OVRCURNT overcurrent in - * - * [18:19] = 10 - * Two UARTs - * - * [17] = 0 - * USB differential mode - * - * [16] = 1 - * PCI disabled - * - * [12:15] = 0101 - * Ethernet 100Mbit with MD - * ETH_0 -> ETH Txen - * ETH_1 -> ETH TxD0 - * ETH_2 -> ETH TxD1 - * ETH_3 -> ETH TxD2 - * ETH_4 -> ETH TxD3 - * ETH_5 -> ETH Txerr - * ETH_6 -> ETH MDC - * ETH_7 -> ETH MDIO - * ETH_8 -> ETH RxDv - * ETH_9 -> ETH RxCLK - * ETH_10 -> ETH Collision - * ETH_11 -> ETH TxD - * ETH_12 -> ETH RxD0 - * ETH_13 -> ETH RxD1 - * ETH_14 -> ETH RxD2 - * ETH_15 -> ETH RxD3 - * ETH_16 -> ETH Rxerr - * ETH_17 -> ETH CRS - * - * [9:11] = 111 - * SPI on PSC6 - * PSC6_0 -> MISO - * PSC6_1 -> SS# - * PSC6_2 -> MOSI - * PSC6_3 -> CLK - * - * [8] = 0 - * IrDA/USB 48MHz clock generated internally - * - * [6:7] = 01 - * ATA chip selects on csb_4/5 - * CSB_4 -> ATA_CS0 out - * CSB_5 -> ATA_CS1 out - * - * [5] = 1 - * PSC3_4 is used as CS6 - * - * [4] = 1 - * PSC3_5 is used as CS7 - * - * [2:3] = 00 - * No Alternatives - * - * [1] = 0 - * gpio_wkup_7 is GPIO - * - * [0] = 0 - * gpio_wkup_6 is GPIO - * - */ -#define CONFIG_SYS_GPS_PORT_CONFIG 0x0d75a162 - -/* - * Miscellaneous configurable options - */ -#define CONFIG_SYS_LONGHELP /* undef to save memory */ -#define CONFIG_SYS_PROMPT "uboot> " /* Monitor Command Prompt */ - -#define CONFIG_CMDLINE_EDITING 1 /* add command line history */ - -#define CONFIG_SYS_CACHELINE_SIZE 32 /* For MPC5xxx CPUs */ -#if defined(CONFIG_CMD_KGDB) -#define CONFIG_SYS_CACHELINE_SHIFT 5 /* log base 2 of the above value */ -#endif - -#if defined(CONFIG_CMD_KGDB) -#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */ -#else -#define CONFIG_SYS_CBSIZE 512 /* Console I/O Buffer Size */ -#endif -#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + sizeof(CONFIG_SYS_PROMPT) + 16) - /* Print Buffer Size */ -#define CONFIG_SYS_MAXARGS 32 /* max number of command args */ -#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */ - -#define CONFIG_SYS_MEMTEST_START 0x00100000 /* memtest works on */ -#define CONFIG_SYS_MEMTEST_END 0x00f00000 /* 1 ... 15 MB in DRAM */ - -#define CONFIG_SYS_LOAD_ADDR 0x400000 /* default load address */ - -#define CONFIG_DISPLAY_BOARDINFO 1 - -#define CONFIG_SYS_HUSH_PARSER 1 - -#define CONFIG_CRC32_VERIFY 1 - -#define CONFIG_BOOTP_DNS -#define CONFIG_BOOTP_DNS2 -#define CONFIG_BOOTP_SEND_HOSTNAME - -#define CONFIG_VERSION_VARIABLE 1 - -/* - * Various low-level settings - */ -#define CONFIG_SYS_HID0_INIT HID0_ICE | HID0_ICFI -#define CONFIG_SYS_HID0_FINAL HID0_ICE - -/* no burst access on the LPB */ -#define CONFIG_SYS_CS_BURST 0x00000000 -/* one deadcycle for the 33MHz statemachine */ -#define CONFIG_SYS_CS_DEADCYCLE 0x33333331 - -#define CONFIG_SYS_BOOTCS_CFG 0x0002d900 -#define CONFIG_SYS_BOOTCS_START CONFIG_SYS_FLASH_BASE -#define CONFIG_SYS_BOOTCS_SIZE CONFIG_SYS_FLASH_SIZE - -#define CONFIG_SYS_RESET_ADDRESS 0xff000000 - -/* - * USB settings - */ -#define CONFIG_USB_CLOCK 0x0001bbbb -/* USB is on PSC3 */ -#define CONFIG_PSC3_USB -#define CONFIG_USB_CONFIG 0x00000100 -#define CONFIG_USB_OHCI -#define CONFIG_USB_STORAGE - -/* - * IDE/ATA stuff Supports IDE harddisk - */ -#undef CONFIG_IDE_8xx_PCCARD /* Use IDE with PC Card Adapter */ -#undef CONFIG_IDE_8xx_DIRECT /* Direct IDE not supported */ -#undef CONFIG_IDE_LED /* LED for ide not supported */ - -#define CONFIG_IDE_RESET 1 /* reset for ide supported */ -#define CONFIG_IDE_PREINIT -#define CONFIG_SYS_IDE_MAXBUS 1 /* max. 1 IDE bus */ -#define CONFIG_SYS_IDE_MAXDEVICE 2 /* max. 2 drives per IDE bus */ -#define CONFIG_SYS_ATA_IDE0_OFFSET 0x0000 -#define CONFIG_SYS_ATA_BASE_ADDR MPC5XXX_ATA -/* Offset for data I/O */ -#define CONFIG_SYS_ATA_DATA_OFFSET (0x0060) -/* Offset for normal register accesses */ -#define CONFIG_SYS_ATA_REG_OFFSET (CONFIG_SYS_ATA_DATA_OFFSET) -/* Offset for alternate registers */ -#define CONFIG_SYS_ATA_ALT_OFFSET (0x005C) -/* Interval between registers */ -#define CONFIG_SYS_ATA_STRIDE 4 -#define CONFIG_ATAPI 1 - -/* we enable IDE and FAT support, so we also need partition support */ -#define CONFIG_DOS_PARTITION 1 - -/* - * Open Firmware flat tree - */ -#define CONFIG_OF_LIBFDT 1 -#define CONFIG_OF_BOARD_SETUP 1 - -#define OF_CPU "PowerPC,5200@0" -#define OF_TBCLK CONFIG_SYS_MPC5XXX_CLKIN -#define OF_SOC "soc5200@f0000000" -#define OF_STDOUT_PATH "/soc5200@f0000000/serial@2600" - -#endif /* __CONFIG_H */