X-Git-Url: http://review.tizen.org/git/?p=platform%2Fkernel%2Fu-boot.git;a=blobdiff_plain;f=include%2Fconfigs%2FTASREG.h;h=5ad93836227b5277f2593fc0e53852f6c296a60d;hp=494ed078f86ac81cdcca3ce5ca17eb7e643aa321;hb=HEAD;hpb=1a4596601fd395f3afb8f82f3f840c5e00bdd57a diff --git a/include/configs/TASREG.h b/include/configs/TASREG.h deleted file mode 100644 index 494ed07..0000000 --- a/include/configs/TASREG.h +++ /dev/null @@ -1,288 +0,0 @@ -/* - * Configuation settings for the esd TASREG board. - * - * (C) Copyright 2004 - * Stefan Roese, esd gmbh germany, stefan.roese@esd-electronics.com - * - * SPDX-License-Identifier: GPL-2.0+ - */ - -/* - * board/config.h - configuration options, board specific - */ - -#ifndef _TASREG_H -#define _TASREG_H - -#ifndef __ASSEMBLY__ -#include -#endif - -/* - * High Level Configuration Options - * (easy to change) - */ -#define CONFIG_MCF52x2 /* define processor family */ -#define CONFIG_M5249 /* define processor type */ - -#define CONFIG_MISC_INIT_R 1 /* call misc_init_r() */ - -#define CONFIG_MCFTMR - -#define CONFIG_MCFUART -#define CONFIG_SYS_UART_PORT (0) -#define CONFIG_BAUDRATE 19200 - -#undef CONFIG_WATCHDOG - -#undef CONFIG_MONITOR_IS_IN_RAM /* no pre-loader required!!! ;-) */ - - -/* - * BOOTP options - */ -#define CONFIG_BOOTP_BOOTFILESIZE -#define CONFIG_BOOTP_BOOTPATH -#define CONFIG_BOOTP_GATEWAY -#define CONFIG_BOOTP_HOSTNAME - - -/* - * Command line configuration. - */ -#include - -#define CONFIG_CMD_BSP -#define CONFIG_CMD_EEPROM -#define CONFIG_CMD_I2C - -#undef CONFIG_CMD_NET - - -#define CONFIG_BOOTDELAY 3 - -#define CONFIG_SYS_PROMPT "=> " -#define CONFIG_SYS_LONGHELP /* undef to save memory */ - -#if defined(CONFIG_CMD_KGDB) -#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */ -#else -#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */ -#endif -#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */ -#define CONFIG_SYS_MAXARGS 16 /* max number of command args */ -#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */ - -#define CONFIG_SYS_DEVICE_NULLDEV 1 /* include nulldev device */ -#define CONFIG_SYS_CONSOLE_INFO_QUIET 1 /* don't print console @ startup*/ -#define CONFIG_AUTO_COMPLETE 1 /* add autocompletion support */ -#define CONFIG_LOOPW 1 /* enable loopw command */ -#define CONFIG_MX_CYCLIC 1 /* enable mdc/mwc commands */ - -#define CONFIG_SYS_LOAD_ADDR 0x200000 /* default load address */ - -#define CONFIG_SYS_MEMTEST_START 0x400 -#define CONFIG_SYS_MEMTEST_END 0x380000 - -#define CONFIG_SYS_HZ 1000 - -/* - * Clock configuration: enable only one of the following options - */ - -#if 0 /* this setting will run the cpu at 11MHz */ -#define CONFIG_SYS_PLL_BYPASS 1 /* bypass PLL for test purpose */ -#undef CONFIG_SYS_FAST_CLK /* MCF5249 can run at 140MHz */ -#define CONFIG_SYS_CLK 11289600 /* PLL bypass */ -#endif - -#if 0 /* this setting will run the cpu at 70MHz */ -#undef CONFIG_SYS_PLL_BYPASS /* bypass PLL for test purpose */ -#undef CONFIG_SYS_FAST_CLK /* MCF5249 can run at 140MHz */ -#define CONFIG_SYS_CLK 72185018 /* The next lower speed */ -#endif - -#if 1 /* this setting will run the cpu at 140MHz */ -#undef CONFIG_SYS_PLL_BYPASS /* bypass PLL for test purpose */ -#define CONFIG_SYS_FAST_CLK 1 /* MCF5249 can run at 140MHz */ -#define CONFIG_SYS_CLK 132025600 /* MCF5249 can run at 140MHz */ -#endif - -/* - * Low Level Configuration Settings - * (address mappings, register initial values, etc.) - * You should know what you are doing if you make changes here. - */ - -#define CONFIG_SYS_MBAR 0x10000000 /* Register Base Addrs */ -#define CONFIG_SYS_MBAR2 0x80000000 - -/*----------------------------------------------------------------------- - * I2C - */ -#define CONFIG_SOFT_I2C -#define CONFIG_SYS_I2C_SPEED 100000 /* I2C speed and slave address */ -#define CONFIG_SYS_I2C_SLAVE 0x7F -#define CONFIG_SYS_I2C_EEPROM_ADDR 0x50 /* EEPROM CAT28WC32 */ -#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 2 /* Bytes of address */ -/* mask of address bits that overflow into the "EEPROM chip address" */ -#define CONFIG_SYS_I2C_EEPROM_ADDR_OVERFLOW 0x01 -#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 5 /* The Catalyst CAT24WC32 has */ - /* 32 byte page write mode using*/ - /* last 5 bits of the address */ -#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 10 /* and takes up to 10 msec */ - -#if defined (CONFIG_SOFT_I2C) -#if 0 /* push-pull */ -#define SDA 0x00800000 -#define SCL 0x00000008 -#define DIR0 *((volatile ulong*)(CONFIG_SYS_MBAR2+MCFSIM_GPIO_EN)) -#define DIR1 *((volatile ulong*)(CONFIG_SYS_MBAR2+MCFSIM_GPIO1_EN)) -#define OUT0 *((volatile ulong*)(CONFIG_SYS_MBAR2+MCFSIM_GPIO_OUT)) -#define OUT1 *((volatile ulong*)(CONFIG_SYS_MBAR2+MCFSIM_GPIO1_OUT)) -#define IN0 *((volatile ulong*)(CONFIG_SYS_MBAR2+MCFSIM_GPIO_READ)) -#define IN1 *((volatile ulong*)(CONFIG_SYS_MBAR2+MCFSIM_GPIO1_READ)) -#define I2C_INIT {OUT1|=SDA;OUT0|=SCL;} -#define I2C_READ ((IN1&SDA)?1:0) -#define I2C_SDA(x) {if(x)OUT1|=SDA;else OUT1&=~SDA;} -#define I2C_SCL(x) {if(x)OUT0|=SCL;else OUT0&=~SCL;} -#define I2C_DELAY {udelay(5);} -#define I2C_ACTIVE {DIR1|=SDA;} -#define I2C_TRISTATE {DIR1&=~SDA;} -#else /* open-collector */ -#define SDA 0x00800000 -#define SCL 0x00000008 -#define DIR0 *((volatile ulong*)(CONFIG_SYS_MBAR2+MCFSIM_GPIO_EN)) -#define DIR1 *((volatile ulong*)(CONFIG_SYS_MBAR2+MCFSIM_GPIO1_EN)) -#define OUT0 *((volatile ulong*)(CONFIG_SYS_MBAR2+MCFSIM_GPIO_OUT)) -#define OUT1 *((volatile ulong*)(CONFIG_SYS_MBAR2+MCFSIM_GPIO1_OUT)) -#define IN0 *((volatile ulong*)(CONFIG_SYS_MBAR2+MCFSIM_GPIO_READ)) -#define IN1 *((volatile ulong*)(CONFIG_SYS_MBAR2+MCFSIM_GPIO1_READ)) -#define I2C_INIT {DIR1&=~SDA;DIR0&=~SCL;OUT1&=~SDA;OUT0&=~SCL;} -#define I2C_READ ((IN1&SDA)?1:0) -#define I2C_SDA(x) {if(x)DIR1&=~SDA;else DIR1|=SDA;} -#define I2C_SCL(x) {if(x)DIR0&=~SCL;else DIR0|=SCL;} -#define I2C_DELAY {udelay(5);} -#define I2C_ACTIVE {DIR1|=SDA;} -#define I2C_TRISTATE {DIR1&=~SDA;} -#endif -#endif - -/*----------------------------------------------------------------------- - * Definitions for initial stack pointer and data area (in DPRAM) - */ -#define CONFIG_SYS_INIT_RAM_ADDR 0x20000000 -#define CONFIG_SYS_INIT_RAM_SIZE 0x1000 /* Size of used area in internal SRAM */ -#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE) -#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET - -#define CONFIG_ENV_IS_IN_FLASH 1 -#define CONFIG_ENV_ADDR 0xFFC40000 /* Address of Environment Sector*/ -#define CONFIG_ENV_SIZE 0x10000 /* Total Size of Environment Sector */ -#define CONFIG_ENV_SECT_SIZE 0x10000 /* see README - env sector total size */ - -/*----------------------------------------------------------------------- - * Start addresses for the final memory configuration - * (Set up by the startup code) - * Please note that CONFIG_SYS_SDRAM_BASE _must_ start at 0 - */ -#define CONFIG_SYS_SDRAM_BASE 0x00000000 -#define CONFIG_SYS_SDRAM_SIZE 16 /* SDRAM size in MB */ -#define CONFIG_SYS_FLASH_BASE CONFIG_SYS_CS0_BASE - -#if 0 /* test-only */ -#define CONFIG_PRAM 512 /* test-only for SDRAM problem!!!!!!!!!!!!!!!!!!!! */ -#endif - -#define CONFIG_SYS_MONITOR_BASE (CONFIG_SYS_FLASH_BASE + 0x400) - -#define CONFIG_SYS_MONITOR_LEN 0x20000 -#define CONFIG_SYS_MALLOC_LEN (1 * 1024*1024) /* Reserve 1 MB for malloc() */ -#define CONFIG_SYS_BOOTPARAMS_LEN 64*1024 - -/* - * For booting Linux, the board info and command line data - * have to be in the first 8 MB of memory, since this is - * the maximum mapped by the Linux kernel during initialization ?? - */ -#define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */ - -/*----------------------------------------------------------------------- - * FLASH organization - */ -#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* max number of memory banks */ -#define CONFIG_SYS_MAX_FLASH_SECT 256 /* max number of sectors on one chip */ - -#define CONFIG_SYS_FLASH_ERASE_TOUT 120000 /* Timeout for Flash Erase (in ms) */ -#define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Timeout for Flash Write (in ms) */ - -#define CONFIG_SYS_FLASH_WORD_SIZE unsigned short /* flash word size (width) */ -#define CONFIG_SYS_FLASH_ADDR0 0x5555 /* 1st address for flash config cycles */ -#define CONFIG_SYS_FLASH_ADDR1 0x2AAA /* 2nd address for flash config cycles */ -/* - * The following defines are added for buggy IOP480 byte interface. - * All other boards should use the standard values (CPCI405 etc.) - */ -#define CONFIG_SYS_FLASH_READ0 0x0000 /* 0 is standard */ -#define CONFIG_SYS_FLASH_READ1 0x0001 /* 1 is standard */ -#define CONFIG_SYS_FLASH_READ2 0x0002 /* 2 is standard */ - -#define CONFIG_SYS_FLASH_EMPTY_INFO /* print 'E' for empty sector on flinfo */ - -/*----------------------------------------------------------------------- - * Cache Configuration - */ -#define CONFIG_SYS_CACHELINE_SIZE 16 - -#define ICACHE_STATUS (CONFIG_SYS_INIT_RAM_ADDR + \ - CONFIG_SYS_INIT_RAM_SIZE - 8) -#define DCACHE_STATUS (CONFIG_SYS_INIT_RAM_ADDR + \ - CONFIG_SYS_INIT_RAM_SIZE - 4) -#define CONFIG_SYS_ICACHE_INV (CF_CACR_DCM) -#define CONFIG_SYS_CACHE_ACR1 (CONFIG_SYS_SDRAM_BASE | \ - CF_ADDRMASK(CONFIG_SYS_SDRAM_SIZE) | \ - CF_ACR_EN | CF_ACR_SM_ALL) -#define CONFIG_SYS_CACHE_ICACR (CF_CACR_CENB | CF_CACR_CEIB | \ - CF_CACR_DBWE) - -/*----------------------------------------------------------------------- - * Memory bank definitions - */ - -/* CS0 - AMD Flash, address 0xffc00000 */ -#define CONFIG_SYS_CS0_BASE 0xffc00000 -#define CONFIG_SYS_CS0_CTRL 0x00001980 /* WS=0110, AA=1, PS=10 */ -/** Note: There is a CSMR0/DRAM vector problem, need to disable C/I ***/ -#define CONFIG_SYS_CS0_MASK 0x003f0021 /* 4MB, AA=0, WP=0, C/I=1, V=1 */ - -/* CS1 - FPGA, address 0xe0000000 */ -#define CONFIG_SYS_CS1_BASE 0xe0000000 -#define CONFIG_SYS_CS1_CTRL 0x00000d80 /* WS=0011, AA=1, PS=10 */ -#define CONFIG_SYS_CS1_MASK 0x00010001 /* 128kB, AA=0, WP=0, C/I=0, V=1*/ - -/*----------------------------------------------------------------------- - * Port configuration - */ -#define CONFIG_SYS_GPIO_FUNC 0x00000008 /* Set gpio pins: none */ -#define CONFIG_SYS_GPIO1_FUNC 0x00df00f0 /* 36-39(SWITCH),48-52(FPGAs),54*/ -#define CONFIG_SYS_GPIO_EN 0x00000008 /* Set gpio output enable */ -#define CONFIG_SYS_GPIO1_EN 0x00c70000 /* Set gpio output enable */ -#define CONFIG_SYS_GPIO_OUT 0x00000008 /* Set outputs to default state */ -#define CONFIG_SYS_GPIO1_OUT 0x00c70000 /* Set outputs to default state */ - -#define CONFIG_SYS_GPIO1_LED 0x00400000 /* user led */ - -/*----------------------------------------------------------------------- - * FPGA stuff - */ -#define CONFIG_SYS_FPGA_SPARTAN2 1 /* using Xilinx Spartan 2 now */ -#define CONFIG_SYS_FPGA_MAX_SIZE 512*1024 /* 512kByte is enough for XC2S200*/ - -/* FPGA program pin configuration */ -#define CONFIG_SYS_FPGA_PRG 0x00010000 /* FPGA program pin (ppc output) */ -#define CONFIG_SYS_FPGA_CLK 0x00040000 /* FPGA clk pin (ppc output) */ -#define CONFIG_SYS_FPGA_DATA 0x00020000 /* FPGA data pin (ppc output) */ -#define CONFIG_SYS_FPGA_INIT 0x00080000 /* FPGA init pin (ppc input) */ -#define CONFIG_SYS_FPGA_DONE 0x00100000 /* FPGA done pin (ppc input) */ - -#endif /* _TASREG_H */