X-Git-Url: http://review.tizen.org/git/?p=platform%2Fkernel%2Fu-boot.git;a=blobdiff_plain;f=include%2Fconfigs%2FMPC8541CDS.h;h=5d229a0d204611a2d23f94ea13c48cfcef356dac;hp=977454167d9b43fbc99ca1c60a0d000ee7fb022a;hb=HEAD;hpb=0ddc9c172279f686077310fbcfa5baf10c719188 diff --git a/include/configs/MPC8541CDS.h b/include/configs/MPC8541CDS.h deleted file mode 100644 index 9774541..0000000 --- a/include/configs/MPC8541CDS.h +++ /dev/null @@ -1,431 +0,0 @@ -/* - * Copyright 2004, 2011 Freescale Semiconductor. - * - * SPDX-License-Identifier: GPL-2.0+ - */ - -/* - * mpc8541cds board configuration file - * - * Please refer to doc/README.mpc85xxcds for more info. - * - */ -#ifndef __CONFIG_H -#define __CONFIG_H - -/* High Level Configuration Options */ -#define CONFIG_CPM2 1 /* has CPM2 */ - -#define CONFIG_SYS_TEXT_BASE 0xfff80000 - -#define CONFIG_PCI_INDIRECT_BRIDGE -#define CONFIG_SYS_PCI_64BIT 1 /* enable 64-bit PCI resources */ -#define CONFIG_TSEC_ENET /* tsec ethernet support */ -#define CONFIG_ENV_OVERWRITE - -#define CONFIG_FSL_VIA - -#ifndef __ASSEMBLY__ -extern unsigned long get_clock_freq(void); -#endif -#define CONFIG_SYS_CLK_FREQ get_clock_freq() /* sysclk for MPC85xx */ - -/* - * These can be toggled for performance analysis, otherwise use default. - */ -#define CONFIG_L2_CACHE /* toggle L2 cache */ -#define CONFIG_BTB /* toggle branch predition */ - -#define CONFIG_SYS_MEMTEST_START 0x00200000 /* memtest works on */ -#define CONFIG_SYS_MEMTEST_END 0x00400000 - -#define CONFIG_SYS_CCSRBAR 0xe0000000 -#define CONFIG_SYS_CCSRBAR_PHYS_LOW CONFIG_SYS_CCSRBAR - -/* DDR Setup */ -#define CONFIG_SPD_EEPROM /* Use SPD EEPROM for DDR setup*/ -#define CONFIG_DDR_SPD -#undef CONFIG_FSL_DDR_INTERACTIVE - -#define CONFIG_MEM_INIT_VALUE 0xDeadBeef - -#define CONFIG_SYS_DDR_SDRAM_BASE 0x00000000 /* DDR is system memory*/ -#define CONFIG_SYS_SDRAM_BASE CONFIG_SYS_DDR_SDRAM_BASE - -#define CONFIG_DIMM_SLOTS_PER_CTLR 1 -#define CONFIG_CHIP_SELECTS_PER_CTRL (2 * CONFIG_DIMM_SLOTS_PER_CTLR) - -/* I2C addresses of SPD EEPROMs */ -#define SPD_EEPROM_ADDRESS 0x51 /* CTLR 0 DIMM 0 */ - -/* - * Make sure required options are set - */ -#ifndef CONFIG_SPD_EEPROM -#error ("CONFIG_SPD_EEPROM is required by MPC85555CDS") -#endif - -#undef CONFIG_CLOCKS_IN_MHZ - -/* - * Local Bus Definitions - */ - -/* - * FLASH on the Local Bus - * Two banks, 8M each, using the CFI driver. - * Boot from BR0/OR0 bank at 0xff00_0000 - * Alternate BR1/OR1 bank at 0xff80_0000 - * - * BR0, BR1: - * Base address 0 = 0xff00_0000 = BR0[0:16] = 1111 1111 0000 0000 0 - * Base address 1 = 0xff80_0000 = BR1[0:16] = 1111 1111 1000 0000 0 - * Port Size = 16 bits = BRx[19:20] = 10 - * Use GPCM = BRx[24:26] = 000 - * Valid = BRx[31] = 1 - * - * 0 4 8 12 16 20 24 28 - * 1111 1111 1000 0000 0001 0000 0000 0001 = ff801001 BR0 - * 1111 1111 0000 0000 0001 0000 0000 0001 = ff001001 BR1 - * - * OR0, OR1: - * Addr Mask = 8M = ORx[0:16] = 1111 1111 1000 0000 0 - * Reserved ORx[17:18] = 11, confusion here? - * CSNT = ORx[20] = 1 - * ACS = half cycle delay = ORx[21:22] = 11 - * SCY = 6 = ORx[24:27] = 0110 - * TRLX = use relaxed timing = ORx[29] = 1 - * EAD = use external address latch delay = OR[31] = 1 - * - * 0 4 8 12 16 20 24 28 - * 1111 1111 1000 0000 0110 1110 0110 0101 = ff806e65 ORx - */ - -#define CONFIG_SYS_FLASH_BASE 0xff000000 /* start of FLASH 8M */ - -#define CONFIG_SYS_BR0_PRELIM 0xff801001 -#define CONFIG_SYS_BR1_PRELIM 0xff001001 - -#define CONFIG_SYS_OR0_PRELIM 0xff806e65 -#define CONFIG_SYS_OR1_PRELIM 0xff806e65 - -#define CONFIG_SYS_FLASH_BANKS_LIST {0xff800000, CONFIG_SYS_FLASH_BASE} -#define CONFIG_SYS_MAX_FLASH_BANKS 2 /* number of banks */ -#define CONFIG_SYS_MAX_FLASH_SECT 128 /* sectors per device */ -#undef CONFIG_SYS_FLASH_CHECKSUM -#define CONFIG_SYS_FLASH_ERASE_TOUT 60000 /* Flash Erase Timeout (ms) */ -#define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (ms) */ - -#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE /* start of monitor */ - -#define CONFIG_FLASH_CFI_DRIVER -#define CONFIG_SYS_FLASH_CFI -#define CONFIG_SYS_FLASH_EMPTY_INFO - -/* - * SDRAM on the Local Bus - */ -#define CONFIG_SYS_LBC_SDRAM_BASE 0xf0000000 /* Localbus SDRAM */ -#define CONFIG_SYS_LBC_SDRAM_SIZE 64 /* LBC SDRAM is 64MB */ - -/* - * Base Register 2 and Option Register 2 configure SDRAM. - * The SDRAM base address, CONFIG_SYS_LBC_SDRAM_BASE, is 0xf0000000. - * - * For BR2, need: - * Base address of 0xf0000000 = BR[0:16] = 1111 0000 0000 0000 0 - * port-size = 32-bits = BR2[19:20] = 11 - * no parity checking = BR2[21:22] = 00 - * SDRAM for MSEL = BR2[24:26] = 011 - * Valid = BR[31] = 1 - * - * 0 4 8 12 16 20 24 28 - * 1111 0000 0000 0000 0001 1000 0110 0001 = f0001861 - * - * FIXME: CONFIG_SYS_LBC_SDRAM_BASE should be masked and OR'ed into - * FIXME: the top 17 bits of BR2. - */ - -#define CONFIG_SYS_BR2_PRELIM 0xf0001861 - -/* - * The SDRAM size in MB, CONFIG_SYS_LBC_SDRAM_SIZE, is 64. - * - * For OR2, need: - * 64MB mask for AM, OR2[0:7] = 1111 1100 - * XAM, OR2[17:18] = 11 - * 9 columns OR2[19-21] = 010 - * 13 rows OR2[23-25] = 100 - * EAD set for extra time OR[31] = 1 - * - * 0 4 8 12 16 20 24 28 - * 1111 1100 0000 0000 0110 1001 0000 0001 = fc006901 - */ - -#define CONFIG_SYS_OR2_PRELIM 0xfc006901 - -#define CONFIG_SYS_LBC_LCRR 0x00030004 /* LB clock ratio reg */ -#define CONFIG_SYS_LBC_LBCR 0x00000000 /* LB config reg */ -#define CONFIG_SYS_LBC_LSRT 0x20000000 /* LB sdram refresh timer */ -#define CONFIG_SYS_LBC_MRTPR 0x00000000 /* LB refresh timer prescal*/ - -/* - * Common settings for all Local Bus SDRAM commands. - * At run time, either BSMA1516 (for CPU 1.1) - * or BSMA1617 (for CPU 1.0) (old) - * is OR'ed in too. - */ -#define CONFIG_SYS_LBC_LSDMR_COMMON ( LSDMR_RFCR16 \ - | LSDMR_PRETOACT7 \ - | LSDMR_ACTTORW7 \ - | LSDMR_BL8 \ - | LSDMR_WRC4 \ - | LSDMR_CL3 \ - | LSDMR_RFEN \ - ) - -/* - * The CADMUS registers are connected to CS3 on CDS. - * The new memory map places CADMUS at 0xf8000000. - * - * For BR3, need: - * Base address of 0xf8000000 = BR[0:16] = 1111 1000 0000 0000 0 - * port-size = 8-bits = BR[19:20] = 01 - * no parity checking = BR[21:22] = 00 - * GPMC for MSEL = BR[24:26] = 000 - * Valid = BR[31] = 1 - * - * 0 4 8 12 16 20 24 28 - * 1111 1000 0000 0000 0000 1000 0000 0001 = f8000801 - * - * For OR3, need: - * 1 MB mask for AM, OR[0:16] = 1111 1111 1111 0000 0 - * disable buffer ctrl OR[19] = 0 - * CSNT OR[20] = 1 - * ACS OR[21:22] = 11 - * XACS OR[23] = 1 - * SCY 15 wait states OR[24:27] = 1111 max is suboptimal but safe - * SETA OR[28] = 0 - * TRLX OR[29] = 1 - * EHTR OR[30] = 1 - * EAD extra time OR[31] = 1 - * - * 0 4 8 12 16 20 24 28 - * 1111 1111 1111 0000 0000 1111 1111 0111 = fff00ff7 - */ - -#define CONFIG_FSL_CADMUS - -#define CADMUS_BASE_ADDR 0xf8000000 -#define CONFIG_SYS_BR3_PRELIM 0xf8000801 -#define CONFIG_SYS_OR3_PRELIM 0xfff00ff7 - -#define CONFIG_SYS_INIT_RAM_LOCK 1 -#define CONFIG_SYS_INIT_RAM_ADDR 0xe4010000 /* Initial RAM address */ -#define CONFIG_SYS_INIT_RAM_SIZE 0x4000 /* Size of used area in RAM */ - -#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE) -#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET - -#define CONFIG_SYS_MONITOR_LEN (256 * 1024) /* Reserve 256 kB for Mon */ -#define CONFIG_SYS_MALLOC_LEN (128 * 1024) /* Reserved for malloc */ - -/* Serial Port */ -#define CONFIG_CONS_INDEX 2 -#define CONFIG_SYS_NS16550_SERIAL -#define CONFIG_SYS_NS16550_REG_SIZE 1 -#define CONFIG_SYS_NS16550_CLK get_bus_freq(0) - -#define CONFIG_SYS_BAUDRATE_TABLE \ - {300, 600, 1200, 2400, 4800, 9600, 19200, 38400,115200} - -#define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_CCSRBAR+0x4500) -#define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_CCSRBAR+0x4600) - -/* - * I2C - */ -#define CONFIG_SYS_I2C -#define CONFIG_SYS_I2C_FSL -#define CONFIG_SYS_FSL_I2C_SPEED 400000 -#define CONFIG_SYS_FSL_I2C_SLAVE 0x7F -#define CONFIG_SYS_FSL_I2C_OFFSET 0x3000 -#define CONFIG_SYS_I2C_NOPROBES { {0, 0x69} } - -/* EEPROM */ -#define CONFIG_ID_EEPROM -#define CONFIG_SYS_I2C_EEPROM_CCID -#define CONFIG_SYS_ID_EEPROM -#define CONFIG_SYS_I2C_EEPROM_ADDR 0x57 -#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 2 - -/* - * General PCI - * Memory space is mapped 1-1, but I/O space must start from 0. - */ -#define CONFIG_SYS_PCI1_MEM_VIRT 0x80000000 -#define CONFIG_SYS_PCI1_MEM_BUS 0x80000000 -#define CONFIG_SYS_PCI1_MEM_PHYS 0x80000000 -#define CONFIG_SYS_PCI1_MEM_SIZE 0x20000000 /* 512M */ -#define CONFIG_SYS_PCI1_IO_VIRT 0xe2000000 -#define CONFIG_SYS_PCI1_IO_BUS 0x00000000 -#define CONFIG_SYS_PCI1_IO_PHYS 0xe2000000 -#define CONFIG_SYS_PCI1_IO_SIZE 0x100000 /* 1M */ - -#define CONFIG_SYS_PCI2_MEM_VIRT 0xa0000000 -#define CONFIG_SYS_PCI2_MEM_BUS 0xa0000000 -#define CONFIG_SYS_PCI2_MEM_PHYS 0xa0000000 -#define CONFIG_SYS_PCI2_MEM_SIZE 0x20000000 /* 512M */ -#define CONFIG_SYS_PCI2_IO_VIRT 0xe2100000 -#define CONFIG_SYS_PCI2_IO_BUS 0x00000000 -#define CONFIG_SYS_PCI2_IO_PHYS 0xe2100000 -#define CONFIG_SYS_PCI2_IO_SIZE 0x100000 /* 1M */ - -#ifdef CONFIG_LEGACY -#define BRIDGE_ID 17 -#define VIA_ID 2 -#else -#define BRIDGE_ID 28 -#define VIA_ID 4 -#endif - -#if defined(CONFIG_PCI) - -#define CONFIG_MPC85XX_PCI2 - -#undef CONFIG_EEPRO100 -#undef CONFIG_TULIP - -#undef CONFIG_PCI_SCAN_SHOW /* show pci devices on startup */ -#define CONFIG_SYS_PCI_SUBSYS_VENDORID 0x1057 /* Motorola */ - -#endif /* CONFIG_PCI */ - -#if defined(CONFIG_TSEC_ENET) - -#define CONFIG_MII 1 /* MII PHY management */ -#define CONFIG_TSEC1 1 -#define CONFIG_TSEC1_NAME "TSEC0" -#define CONFIG_TSEC2 1 -#define CONFIG_TSEC2_NAME "TSEC1" -#define TSEC1_PHY_ADDR 0 -#define TSEC2_PHY_ADDR 1 -#define TSEC1_PHYIDX 0 -#define TSEC2_PHYIDX 0 -#define TSEC1_FLAGS TSEC_GIGABIT -#define TSEC2_FLAGS TSEC_GIGABIT - -/* Options are: TSEC[0-1] */ -#define CONFIG_ETHPRIME "TSEC0" - -#endif /* CONFIG_TSEC_ENET */ - -/* - * Environment - */ -#define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE + 0x40000) -#define CONFIG_ENV_SECT_SIZE 0x40000 /* 256K(one sector) for env */ -#define CONFIG_ENV_SIZE 0x2000 - -#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */ -#define CONFIG_SYS_LOADS_BAUD_CHANGE 1 /* allow baudrate change */ - -/* - * BOOTP options - */ -#define CONFIG_BOOTP_BOOTFILESIZE -#define CONFIG_BOOTP_BOOTPATH -#define CONFIG_BOOTP_GATEWAY -#define CONFIG_BOOTP_HOSTNAME - -/* - * Command line configuration. - */ -#define CONFIG_CMD_REGINFO - -#if defined(CONFIG_PCI) - #define CONFIG_CMD_PCI -#endif - -#undef CONFIG_WATCHDOG /* watchdog disabled */ - -/* - * Miscellaneous configurable options - */ -#define CONFIG_SYS_LONGHELP /* undef to save memory */ -#define CONFIG_CMDLINE_EDITING /* Command-line editing */ -#define CONFIG_AUTO_COMPLETE /* add autocompletion support */ -#define CONFIG_SYS_LOAD_ADDR 0x2000000 /* default load address */ -#if defined(CONFIG_CMD_KGDB) -#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */ -#else -#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */ -#endif -#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */ -#define CONFIG_SYS_MAXARGS 16 /* max number of command args */ -#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */ - -/* - * For booting Linux, the board info and command line data - * have to be in the first 64 MB of memory, since this is - * the maximum mapped by the Linux kernel during initialization. - */ -#define CONFIG_SYS_BOOTMAPSZ (64 << 20) /* Initial Memory map for Linux*/ -#define CONFIG_SYS_BOOTM_LEN (64 << 20) /* Increase max gunzip size */ - -#if defined(CONFIG_CMD_KGDB) -#define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */ -#endif - -/* - * Environment Configuration - */ - -/* The mac addresses for all ethernet interface */ -#if defined(CONFIG_TSEC_ENET) -#define CONFIG_HAS_ETH0 -#define CONFIG_HAS_ETH1 -#define CONFIG_HAS_ETH2 -#endif - -#define CONFIG_IPADDR 192.168.1.253 - -#define CONFIG_HOSTNAME unknown -#define CONFIG_ROOTPATH "/nfsroot" -#define CONFIG_BOOTFILE "your.uImage" - -#define CONFIG_SERVERIP 192.168.1.1 -#define CONFIG_GATEWAYIP 192.168.1.1 -#define CONFIG_NETMASK 255.255.255.0 - -#define CONFIG_LOADADDR 200000 /*default location for tftp and bootm*/ - -#undef CONFIG_BOOTARGS /* the boot command will set bootargs*/ - -#define CONFIG_EXTRA_ENV_SETTINGS \ - "netdev=eth0\0" \ - "consoledev=ttyS1\0" \ - "ramdiskaddr=600000\0" \ - "ramdiskfile=your.ramdisk.u-boot\0" \ - "fdtaddr=400000\0" \ - "fdtfile=your.fdt.dtb\0" - -#define CONFIG_NFSBOOTCOMMAND \ - "setenv bootargs root=/dev/nfs rw " \ - "nfsroot=$serverip:$rootpath " \ - "ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:$netdev:off " \ - "console=$consoledev,$baudrate $othbootargs;" \ - "tftp $loadaddr $bootfile;" \ - "tftp $fdtaddr $fdtfile;" \ - "bootm $loadaddr - $fdtaddr" - -#define CONFIG_RAMBOOTCOMMAND \ - "setenv bootargs root=/dev/ram rw " \ - "console=$consoledev,$baudrate $othbootargs;" \ - "tftp $ramdiskaddr $ramdiskfile;" \ - "tftp $loadaddr $bootfile;" \ - "bootm $loadaddr $ramdiskaddr" - -#define CONFIG_BOOTCOMMAND CONFIG_NFSBOOTCOMMAND - -#endif /* __CONFIG_H */