X-Git-Url: http://review.tizen.org/git/?p=platform%2Fkernel%2Fu-boot.git;a=blobdiff_plain;f=include%2Fconfigs%2FMPC832XEMDS.h;h=1735b3c5216e1f8002a04f90767673d0bfb1f04a;hp=e92a8c014848df864a35470b6063e13a4e023395;hb=HEAD;hpb=e8f80a5a58c9b506453cc0780687e8ed457d30a6 diff --git a/include/configs/MPC832XEMDS.h b/include/configs/MPC832XEMDS.h deleted file mode 100644 index e92a8c0..0000000 --- a/include/configs/MPC832XEMDS.h +++ /dev/null @@ -1,564 +0,0 @@ -/* SPDX-License-Identifier: GPL-2.0+ */ -/* - * Copyright (C) 2006 Freescale Semiconductor, Inc. - */ - -#ifndef __CONFIG_H -#define __CONFIG_H - -/* - * High Level Configuration Options - */ -#define CONFIG_E300 1 /* E300 family */ -#define CONFIG_QE 1 /* Has QE */ -#define CONFIG_MPC832x 1 /* MPC832x CPU specific */ -#define CONFIG_MPC832XEMDS 1 /* MPC832XEMDS board specific */ - -/* - * System Clock Setup - */ -#ifdef CONFIG_PCISLAVE -#define CONFIG_83XX_PCICLK 66000000 /* in HZ */ -#else -#define CONFIG_83XX_CLKIN 66000000 /* in Hz */ -#endif - -#ifndef CONFIG_SYS_CLK_FREQ -#define CONFIG_SYS_CLK_FREQ 66000000 -#endif - -/* - * Hardware Reset Configuration Word - */ -#define CONFIG_SYS_HRCW_LOW (\ - HRCWL_LCL_BUS_TO_SCB_CLK_1X1 |\ - HRCWL_DDR_TO_SCB_CLK_2X1 |\ - HRCWL_VCO_1X2 |\ - HRCWL_CSB_TO_CLKIN_2X1 |\ - HRCWL_CORE_TO_CSB_2X1 |\ - HRCWL_CE_PLL_VCO_DIV_2 |\ - HRCWL_CE_PLL_DIV_1X1 |\ - HRCWL_CE_TO_PLL_1X3) - -#ifdef CONFIG_PCISLAVE -#define CONFIG_SYS_HRCW_HIGH (\ - HRCWH_PCI_AGENT |\ - HRCWH_PCI1_ARBITER_DISABLE |\ - HRCWH_CORE_ENABLE |\ - HRCWH_FROM_0XFFF00100 |\ - HRCWH_BOOTSEQ_DISABLE |\ - HRCWH_SW_WATCHDOG_DISABLE |\ - HRCWH_ROM_LOC_LOCAL_16BIT |\ - HRCWH_BIG_ENDIAN |\ - HRCWH_LALE_NORMAL) -#else -#define CONFIG_SYS_HRCW_HIGH (\ - HRCWH_PCI_HOST |\ - HRCWH_PCI1_ARBITER_ENABLE |\ - HRCWH_CORE_ENABLE |\ - HRCWH_FROM_0X00000100 |\ - HRCWH_BOOTSEQ_DISABLE |\ - HRCWH_SW_WATCHDOG_DISABLE |\ - HRCWH_ROM_LOC_LOCAL_16BIT |\ - HRCWH_BIG_ENDIAN |\ - HRCWH_LALE_NORMAL) -#endif - -/* - * System IO Config - */ -#define CONFIG_SYS_SICRL 0x00000000 - -/* - * IMMR new address - */ -#define CONFIG_SYS_IMMR 0xE0000000 - -/* - * DDR Setup - */ -#define CONFIG_SYS_DDR_BASE 0x00000000 /* DDR is system memory */ -#define CONFIG_SYS_SDRAM_BASE CONFIG_SYS_DDR_BASE -#define CONFIG_SYS_DDR_SDRAM_BASE CONFIG_SYS_DDR_BASE -#define CONFIG_SYS_DDRCDR 0x73000002 /* DDR II voltage is 1.8V */ - -#undef CONFIG_SPD_EEPROM -#if defined(CONFIG_SPD_EEPROM) -/* Determine DDR configuration from I2C interface - */ -#define SPD_EEPROM_ADDRESS 0x51 /* DDR SODIMM */ -#else -/* Manually set up DDR parameters - */ -#define CONFIG_SYS_DDR_SIZE 128 /* MB */ -#define CONFIG_SYS_DDR_CS0_CONFIG (CSCONFIG_EN \ - | CSCONFIG_AP \ - | CSCONFIG_ODT_WR_CFG \ - | CSCONFIG_ROW_BIT_13 \ - | CSCONFIG_COL_BIT_10) - /* 0x80840102 */ -#define CONFIG_SYS_DDR_TIMING_0 ((0 << TIMING_CFG0_RWT_SHIFT) \ - | (0 << TIMING_CFG0_WRT_SHIFT) \ - | (0 << TIMING_CFG0_RRT_SHIFT) \ - | (0 << TIMING_CFG0_WWT_SHIFT) \ - | (2 << TIMING_CFG0_ACT_PD_EXIT_SHIFT) \ - | (2 << TIMING_CFG0_PRE_PD_EXIT_SHIFT) \ - | (8 << TIMING_CFG0_ODT_PD_EXIT_SHIFT) \ - | (2 << TIMING_CFG0_MRS_CYC_SHIFT)) - /* 0x00220802 */ -#define CONFIG_SYS_DDR_TIMING_1 ((3 << TIMING_CFG1_PRETOACT_SHIFT) \ - | (9 << TIMING_CFG1_ACTTOPRE_SHIFT) \ - | (3 << TIMING_CFG1_ACTTORW_SHIFT) \ - | (5 << TIMING_CFG1_CASLAT_SHIFT) \ - | (13 << TIMING_CFG1_REFREC_SHIFT) \ - | (3 << TIMING_CFG1_WRREC_SHIFT) \ - | (2 << TIMING_CFG1_ACTTOACT_SHIFT) \ - | (2 << TIMING_CFG1_WRTORD_SHIFT)) - /* 0x3935D322 */ -#define CONFIG_SYS_DDR_TIMING_2 ((0 << TIMING_CFG2_ADD_LAT_SHIFT) \ - | (31 << TIMING_CFG2_CPO_SHIFT) \ - | (2 << TIMING_CFG2_WR_LAT_DELAY_SHIFT) \ - | (2 << TIMING_CFG2_RD_TO_PRE_SHIFT) \ - | (2 << TIMING_CFG2_WR_DATA_DELAY_SHIFT) \ - | (3 << TIMING_CFG2_CKE_PLS_SHIFT) \ - | (10 << TIMING_CFG2_FOUR_ACT_SHIFT)) - /* 0x0F9048CA */ -#define CONFIG_SYS_DDR_TIMING_3 0x00000000 -#define CONFIG_SYS_DDR_CLK_CNTL DDR_SDRAM_CLK_CNTL_CLK_ADJUST_05 - /* 0x02000000 */ -#define CONFIG_SYS_DDR_MODE ((0x4440 << SDRAM_MODE_ESD_SHIFT) \ - | (0x0232 << SDRAM_MODE_SD_SHIFT)) - /* 0x44400232 */ -#define CONFIG_SYS_DDR_MODE2 0x8000c000 -#define CONFIG_SYS_DDR_INTERVAL ((800 << SDRAM_INTERVAL_REFINT_SHIFT) \ - | (100 << SDRAM_INTERVAL_BSTOPRE_SHIFT)) - /* 0x03200064 */ -#define CONFIG_SYS_DDR_CS0_BNDS 0x00000007 -#define CONFIG_SYS_DDR_SDRAM_CFG (SDRAM_CFG_SREN \ - | SDRAM_CFG_SDRAM_TYPE_DDR2 \ - | SDRAM_CFG_32_BE) - /* 0x43080000 */ -#define CONFIG_SYS_DDR_SDRAM_CFG2 0x00401000 -#endif - -/* - * Memory test - */ -#undef CONFIG_SYS_DRAM_TEST /* memory test, takes time */ -#define CONFIG_SYS_MEMTEST_START 0x00000000 /* memtest region */ -#define CONFIG_SYS_MEMTEST_END 0x00100000 - -/* - * The reserved memory - */ -#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE /* start of monitor */ - -#if (CONFIG_SYS_MONITOR_BASE < CONFIG_SYS_FLASH_BASE) -#define CONFIG_SYS_RAMBOOT -#else -#undef CONFIG_SYS_RAMBOOT -#endif - -/* CONFIG_SYS_MONITOR_LEN must be a multiple of CONFIG_ENV_SECT_SIZE */ -#define CONFIG_SYS_MONITOR_LEN (512 * 1024) /* Reserve 512 kB for Mon */ -#define CONFIG_SYS_MALLOC_LEN (256 * 1024) /* Reserved for malloc */ - -/* - * Initial RAM Base Address Setup - */ -#define CONFIG_SYS_INIT_RAM_LOCK 1 -#define CONFIG_SYS_INIT_RAM_ADDR 0xE6000000 /* Initial RAM addr */ -#define CONFIG_SYS_INIT_RAM_SIZE 0x1000 /* Size of used area in RAM */ -#define CONFIG_SYS_GBL_DATA_OFFSET \ - (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE) - -/* - * Local Bus Configuration & Clock Setup - */ -#define CONFIG_SYS_LCRR_DBYP LCRR_DBYP -#define CONFIG_SYS_LCRR_CLKDIV LCRR_CLKDIV_2 -#define CONFIG_SYS_LBC_LBCR 0x00000000 - -/* - * FLASH on the Local Bus - */ -#define CONFIG_SYS_FLASH_CFI /* use the Common Flash Interface */ -#define CONFIG_FLASH_CFI_DRIVER /* use the CFI driver */ -#define CONFIG_SYS_FLASH_BASE 0xFE000000 /* FLASH base address */ -#define CONFIG_SYS_FLASH_SIZE 16 /* FLASH size is 16M */ -#define CONFIG_SYS_FLASH_PROTECTION 1 /* Use h/w Flash protection. */ - - /* Window base at flash base */ -#define CONFIG_SYS_LBLAWBAR0_PRELIM CONFIG_SYS_FLASH_BASE -#define CONFIG_SYS_LBLAWAR0_PRELIM (LBLAWAR_EN | LBLAWAR_32MB) - -#define CONFIG_SYS_BR0_PRELIM (CONFIG_SYS_FLASH_BASE \ - | BR_PS_16 /* 16 bit port */ \ - | BR_MS_GPCM /* MSEL = GPCM */ \ - | BR_V) /* valid */ -#define CONFIG_SYS_OR0_PRELIM (MEG_TO_AM(CONFIG_SYS_FLASH_SIZE) \ - | OR_GPCM_XAM \ - | OR_GPCM_CSNT \ - | OR_GPCM_ACS_DIV2 \ - | OR_GPCM_XACS \ - | OR_GPCM_SCY_15 \ - | OR_GPCM_TRLX_SET \ - | OR_GPCM_EHTR_SET \ - | OR_GPCM_EAD) - /* 0xfe006ff7 */ - -#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* number of banks */ -#define CONFIG_SYS_MAX_FLASH_SECT 128 /* sectors per device */ - -#undef CONFIG_SYS_FLASH_CHECKSUM - -/* - * BCSR on the Local Bus - */ -#define CONFIG_SYS_BCSR 0xF8000000 - /* Access window base at BCSR base */ -#define CONFIG_SYS_LBLAWBAR1_PRELIM CONFIG_SYS_BCSR -#define CONFIG_SYS_LBLAWAR1_PRELIM (LBLAWAR_EN | LBLAWAR_32KB) - -#define CONFIG_SYS_BR1_PRELIM (CONFIG_SYS_BCSR \ - | BR_PS_8 \ - | BR_MS_GPCM \ - | BR_V) -#define CONFIG_SYS_OR1_PRELIM (OR_AM_32KB \ - | OR_GPCM_XAM \ - | OR_GPCM_CSNT \ - | OR_GPCM_XACS \ - | OR_GPCM_SCY_15 \ - | OR_GPCM_TRLX_SET \ - | OR_GPCM_EHTR_SET \ - | OR_GPCM_EAD) - /* 0xFFFFE9F7 */ - -/* - * Windows to access PIB via local bus - */ - /* PIB window base 0xF8008000 */ -#define CONFIG_SYS_PIB_BASE 0xF8008000 -#define CONFIG_SYS_PIB_WINDOW_SIZE (32 * 1024) -#define CONFIG_SYS_LBLAWBAR3_PRELIM CONFIG_SYS_PIB_BASE -#define CONFIG_SYS_LBLAWAR3_PRELIM (LBLAWAR_EN | LBLAWAR_64KB) - -/* - * CS2 on Local Bus, to PIB - */ -#define CONFIG_SYS_BR2_PRELIM (CONFIG_SYS_PIB_BASE \ - | BR_PS_8 \ - | BR_MS_GPCM \ - | BR_V) - /* 0xF8008801 */ -#define CONFIG_SYS_OR2_PRELIM (P2SZ_TO_AM(CONFIG_SYS_PIB_WINDOW_SIZE) \ - | OR_GPCM_XAM \ - | OR_GPCM_CSNT \ - | OR_GPCM_XACS \ - | OR_GPCM_SCY_15 \ - | OR_GPCM_TRLX_SET \ - | OR_GPCM_EHTR_SET \ - | OR_GPCM_EAD) - /* 0xffffe9f7 */ - -/* - * CS3 on Local Bus, to PIB - */ -#define CONFIG_SYS_BR3_PRELIM ((CONFIG_SYS_PIB_BASE + \ - CONFIG_SYS_PIB_WINDOW_SIZE) \ - | BR_PS_8 \ - | BR_MS_GPCM \ - | BR_V) - /* 0xF8010801 */ -#define CONFIG_SYS_OR3_PRELIM (P2SZ_TO_AM(CONFIG_SYS_PIB_WINDOW_SIZE) \ - | OR_GPCM_XAM \ - | OR_GPCM_CSNT \ - | OR_GPCM_XACS \ - | OR_GPCM_SCY_15 \ - | OR_GPCM_TRLX_SET \ - | OR_GPCM_EHTR_SET \ - | OR_GPCM_EAD) - /* 0xffffe9f7 */ - -/* - * Serial Port - */ -#define CONFIG_SYS_NS16550_SERIAL -#define CONFIG_SYS_NS16550_REG_SIZE 1 -#define CONFIG_SYS_NS16550_CLK get_bus_freq(0) - -#define CONFIG_SYS_BAUDRATE_TABLE \ - {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 115200} - -#define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_IMMR+0x4500) -#define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_IMMR+0x4600) - -/* I2C */ -#define CONFIG_SYS_I2C -#define CONFIG_SYS_I2C_FSL -#define CONFIG_SYS_FSL_I2C_SPEED 400000 -#define CONFIG_SYS_FSL_I2C_SLAVE 0x7F -#define CONFIG_SYS_FSL_I2C_OFFSET 0x3000 -#define CONFIG_SYS_I2C_NOPROBES { {0, 0x51} } - -/* - * Config on-board RTC - */ -#define CONFIG_RTC_DS1374 /* use ds1374 rtc via i2c */ -#define CONFIG_SYS_I2C_RTC_ADDR 0x68 /* at address 0x68 */ - -/* - * General PCI - * Addresses are mapped 1-1. - */ -#define CONFIG_SYS_PCI1_MEM_BASE 0x80000000 -#define CONFIG_SYS_PCI1_MEM_PHYS CONFIG_SYS_PCI1_MEM_BASE -#define CONFIG_SYS_PCI1_MEM_SIZE 0x10000000 /* 256M */ -#define CONFIG_SYS_PCI1_MMIO_BASE 0x90000000 -#define CONFIG_SYS_PCI1_MMIO_PHYS CONFIG_SYS_PCI1_MMIO_BASE -#define CONFIG_SYS_PCI1_MMIO_SIZE 0x10000000 /* 256M */ -#define CONFIG_SYS_PCI1_IO_BASE 0x00000000 -#define CONFIG_SYS_PCI1_IO_PHYS 0xE0300000 -#define CONFIG_SYS_PCI1_IO_SIZE 0x100000 /* 1M */ - -#define CONFIG_SYS_PCI_SLV_MEM_LOCAL CONFIG_SYS_SDRAM_BASE -#define CONFIG_SYS_PCI_SLV_MEM_BUS 0x00000000 -#define CONFIG_SYS_PCI_SLV_MEM_SIZE 0x80000000 - -#ifdef CONFIG_PCI -#define CONFIG_PCI_INDIRECT_BRIDGE - -#define CONFIG_83XX_PCI_STREAMING - -#undef CONFIG_EEPRO100 -#undef CONFIG_PCI_SCAN_SHOW /* show pci devices on startup */ -#define CONFIG_SYS_PCI_SUBSYS_VENDORID 0x1957 /* Freescale */ - -#endif /* CONFIG_PCI */ - -/* - * QE UEC ethernet configuration - */ -#define CONFIG_UEC_ETH -#define CONFIG_ETHPRIME "UEC0" - -#define CONFIG_UEC_ETH1 /* ETH3 */ - -#ifdef CONFIG_UEC_ETH1 -#define CONFIG_SYS_UEC1_UCC_NUM 2 /* UCC3 */ -#define CONFIG_SYS_UEC1_RX_CLK QE_CLK9 -#define CONFIG_SYS_UEC1_TX_CLK QE_CLK10 -#define CONFIG_SYS_UEC1_ETH_TYPE FAST_ETH -#define CONFIG_SYS_UEC1_PHY_ADDR 3 -#define CONFIG_SYS_UEC1_INTERFACE_TYPE PHY_INTERFACE_MODE_MII -#define CONFIG_SYS_UEC1_INTERFACE_SPEED 100 -#endif - -#define CONFIG_UEC_ETH2 /* ETH4 */ - -#ifdef CONFIG_UEC_ETH2 -#define CONFIG_SYS_UEC2_UCC_NUM 3 /* UCC4 */ -#define CONFIG_SYS_UEC2_RX_CLK QE_CLK7 -#define CONFIG_SYS_UEC2_TX_CLK QE_CLK8 -#define CONFIG_SYS_UEC2_ETH_TYPE FAST_ETH -#define CONFIG_SYS_UEC2_PHY_ADDR 4 -#define CONFIG_SYS_UEC2_INTERFACE_TYPE PHY_INTERFACE_MODE_MII -#define CONFIG_SYS_UEC2_INTERFACE_SPEED 100 -#endif - -/* - * Environment - */ -#ifndef CONFIG_SYS_RAMBOOT - #define CONFIG_ENV_ADDR \ - (CONFIG_SYS_MONITOR_BASE + CONFIG_SYS_MONITOR_LEN) - #define CONFIG_ENV_SECT_SIZE 0x20000 - #define CONFIG_ENV_SIZE 0x2000 -#else - #define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE - 0x1000) - #define CONFIG_ENV_SIZE 0x2000 -#endif - -#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */ -#define CONFIG_SYS_LOADS_BAUD_CHANGE 1 /* allow baudrate change */ - -/* - * BOOTP options - */ -#define CONFIG_BOOTP_BOOTFILESIZE - -/* - * Command line configuration. - */ - -#undef CONFIG_WATCHDOG /* watchdog disabled */ - -/* - * Miscellaneous configurable options - */ -#define CONFIG_SYS_LOAD_ADDR 0x2000000 /* default load address */ - -/* - * For booting Linux, the board info and command line data - * have to be in the first 256 MB of memory, since this is - * the maximum mapped by the Linux kernel during initialization. - */ - /* Initial Memory map for Linux */ -#define CONFIG_SYS_BOOTMAPSZ (256 << 20) -#define CONFIG_SYS_BOOTM_LEN (64 << 20) /* Increase max gunzip size */ - -/* - * Core HID Setup - */ -#define CONFIG_SYS_HID0_INIT 0x000000000 -#define CONFIG_SYS_HID0_FINAL (HID0_ENABLE_MACHINE_CHECK | \ - HID0_ENABLE_INSTRUCTION_CACHE) -#define CONFIG_SYS_HID2 HID2_HBE - -/* - * MMU Setup - */ - -#define CONFIG_HIGH_BATS 1 /* High BATs supported */ - -/* DDR: cache cacheable */ -#define CONFIG_SYS_IBAT0L (CONFIG_SYS_SDRAM_BASE \ - | BATL_PP_RW \ - | BATL_MEMCOHERENCE) -#define CONFIG_SYS_IBAT0U (CONFIG_SYS_SDRAM_BASE \ - | BATU_BL_256M \ - | BATU_VS \ - | BATU_VP) -#define CONFIG_SYS_DBAT0L CONFIG_SYS_IBAT0L -#define CONFIG_SYS_DBAT0U CONFIG_SYS_IBAT0U - -/* IMMRBAR & PCI IO: cache-inhibit and guarded */ -#define CONFIG_SYS_IBAT1L (CONFIG_SYS_IMMR \ - | BATL_PP_RW \ - | BATL_CACHEINHIBIT \ - | BATL_GUARDEDSTORAGE) -#define CONFIG_SYS_IBAT1U (CONFIG_SYS_IMMR \ - | BATU_BL_4M \ - | BATU_VS \ - | BATU_VP) -#define CONFIG_SYS_DBAT1L CONFIG_SYS_IBAT1L -#define CONFIG_SYS_DBAT1U CONFIG_SYS_IBAT1U - -/* BCSR: cache-inhibit and guarded */ -#define CONFIG_SYS_IBAT2L (CONFIG_SYS_BCSR \ - | BATL_PP_RW \ - | BATL_CACHEINHIBIT \ - | BATL_GUARDEDSTORAGE) -#define CONFIG_SYS_IBAT2U (CONFIG_SYS_BCSR \ - | BATU_BL_128K \ - | BATU_VS \ - | BATU_VP) -#define CONFIG_SYS_DBAT2L CONFIG_SYS_IBAT2L -#define CONFIG_SYS_DBAT2U CONFIG_SYS_IBAT2U - -/* FLASH: icache cacheable, but dcache-inhibit and guarded */ -#define CONFIG_SYS_IBAT3L (CONFIG_SYS_FLASH_BASE \ - | BATL_PP_RW \ - | BATL_MEMCOHERENCE) -#define CONFIG_SYS_IBAT3U (CONFIG_SYS_FLASH_BASE \ - | BATU_BL_32M \ - | BATU_VS \ - | BATU_VP) -#define CONFIG_SYS_DBAT3L (CONFIG_SYS_FLASH_BASE \ - | BATL_PP_RW \ - | BATL_CACHEINHIBIT \ - | BATL_GUARDEDSTORAGE) -#define CONFIG_SYS_DBAT3U CONFIG_SYS_IBAT3U - -#define CONFIG_SYS_IBAT4L (0) -#define CONFIG_SYS_IBAT4U (0) -#define CONFIG_SYS_DBAT4L CONFIG_SYS_IBAT4L -#define CONFIG_SYS_DBAT4U CONFIG_SYS_IBAT4U - -/* Stack in dcache: cacheable, no memory coherence */ -#define CONFIG_SYS_IBAT5L (CONFIG_SYS_INIT_RAM_ADDR | BATL_PP_RW) -#define CONFIG_SYS_IBAT5U (CONFIG_SYS_INIT_RAM_ADDR \ - | BATU_BL_128K \ - | BATU_VS \ - | BATU_VP) -#define CONFIG_SYS_DBAT5L CONFIG_SYS_IBAT5L -#define CONFIG_SYS_DBAT5U CONFIG_SYS_IBAT5U - -#ifdef CONFIG_PCI -/* PCI MEM space: cacheable */ -#define CONFIG_SYS_IBAT6L (CONFIG_SYS_PCI1_MEM_PHYS \ - | BATL_PP_RW \ - | BATL_MEMCOHERENCE) -#define CONFIG_SYS_IBAT6U (CONFIG_SYS_PCI1_MEM_PHYS \ - | BATU_BL_256M \ - | BATU_VS \ - | BATU_VP) -#define CONFIG_SYS_DBAT6L CONFIG_SYS_IBAT6L -#define CONFIG_SYS_DBAT6U CONFIG_SYS_IBAT6U -/* PCI MMIO space: cache-inhibit and guarded */ -#define CONFIG_SYS_IBAT7L (CONFIG_SYS_PCI1_MMIO_PHYS \ - | BATL_PP_RW \ - | BATL_CACHEINHIBIT \ - | BATL_GUARDEDSTORAGE) -#define CONFIG_SYS_IBAT7U (CONFIG_SYS_PCI1_MMIO_PHYS \ - | BATU_BL_256M \ - | BATU_VS \ - | BATU_VP) -#define CONFIG_SYS_DBAT7L CONFIG_SYS_IBAT7L -#define CONFIG_SYS_DBAT7U CONFIG_SYS_IBAT7U -#else -#define CONFIG_SYS_IBAT6L (0) -#define CONFIG_SYS_IBAT6U (0) -#define CONFIG_SYS_IBAT7L (0) -#define CONFIG_SYS_IBAT7U (0) -#define CONFIG_SYS_DBAT6L CONFIG_SYS_IBAT6L -#define CONFIG_SYS_DBAT6U CONFIG_SYS_IBAT6U -#define CONFIG_SYS_DBAT7L CONFIG_SYS_IBAT7L -#define CONFIG_SYS_DBAT7U CONFIG_SYS_IBAT7U -#endif - -#if defined(CONFIG_CMD_KGDB) -#define CONFIG_KGDB_BAUDRATE 230400 /* speed of kgdb serial port */ -#endif - -/* - * Environment Configuration - */ #define CONFIG_ENV_OVERWRITE - -#if defined(CONFIG_UEC_ETH) -#define CONFIG_HAS_ETH0 -#define CONFIG_HAS_ETH1 -#endif - -#define CONFIG_LOADADDR 800000 /* default location for tftp and bootm */ - -#define CONFIG_EXTRA_ENV_SETTINGS \ - "netdev=eth0\0" \ - "consoledev=ttyS0\0" \ - "ramdiskaddr=1000000\0" \ - "ramdiskfile=ramfs.83xx\0" \ - "fdtaddr=780000\0" \ - "fdtfile=mpc832x_mds.dtb\0" \ - "" - -#define CONFIG_NFSBOOTCOMMAND \ - "setenv bootargs root=/dev/nfs rw " \ - "nfsroot=$serverip:$rootpath " \ - "ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:" \ - "$netdev:off " \ - "console=$consoledev,$baudrate $othbootargs;" \ - "tftp $loadaddr $bootfile;" \ - "tftp $fdtaddr $fdtfile;" \ - "bootm $loadaddr - $fdtaddr" - -#define CONFIG_RAMBOOTCOMMAND \ - "setenv bootargs root=/dev/ram rw " \ - "console=$consoledev,$baudrate $othbootargs;" \ - "tftp $ramdiskaddr $ramdiskfile;" \ - "tftp $loadaddr $bootfile;" \ - "tftp $fdtaddr $fdtfile;" \ - "bootm $loadaddr $ramdiskaddr $fdtaddr" - -#define CONFIG_BOOTCOMMAND CONFIG_NFSBOOTCOMMAND - -#endif /* __CONFIG_H */