Convert CONFIG_CMD_ASKENV et al to Kconfig

[platform/kernel/u-boot.git] / include / configs / zmx25.h

diff --git a/include/configs/zmx25.h b/include/configs/zmx25.h
index af7cc49..15bd97f 100644 (file)
--- a/include/configs/zmx25.h
+++ b/include/configs/zmx25.h
@@ -1,10 +1,9 @@
+/* SPDX-License-Identifier: GPL-2.0+ */
 /*
  * (c) 2011 Graf-Syteco, Matthias Weisser
  * <weisserm@arcor.de>
  *
  * Configuation settings for the zmx25 board
- *
- * SPDX-License-Identifier:    GPL-2.0+
  */
 
 #ifndef __CONFIG_H
@@ -12,11 +11,6 @@
 
 #include <asm/arch/imx-regs.h>
 
-#define CONFIG_MX25
-#define CONFIG_SYS_TEXT_BASE           0xA0000000
-
-#define CONFIG_SYS_GENERIC_BOARD
-
 #define CONFIG_SYS_TIMER_RATE          32768
 #define CONFIG_SYS_TIMER_COUNTER       \
        (&((struct gpt_regs *)IMX_GPT1_BASE)->counter)
@@ -35,79 +29,41 @@
 #define CONFIG_CMDLINE_TAG             /* enable passing of ATAGs      */
 #define CONFIG_SETUP_MEMORY_TAGS
 #define CONFIG_INITRD_TAG
-#define CONFIG_BOARD_LATE_INIT
-
-/*
- * Compressions
- */
-#define CONFIG_LZO
 
 /*
  * Hardware drivers
  */
 
 /*
- * GPIO
- */
-#define CONFIG_MXC_GPIO
-
-/*
  * Serial
  */
 #define CONFIG_MXC_UART
 #define CONFIG_MXC_UART_BASE   UART2_BASE
-#define CONFIG_CONS_INDEX      1       /* use UART2 for console */
-#define CONFIG_BAUDRATE                115200  /* Default baud rate */
 
 /*
  * Ethernet
  */
 #define CONFIG_FEC_MXC
 #define CONFIG_FEC_MXC_PHYADDR         0x00
-#define CONFIG_MII
 
 /*
  * BOOTP options
  */
 #define CONFIG_BOOTP_BOOTFILESIZE
-#define CONFIG_BOOTP_BOOTPATH
-#define CONFIG_BOOTP_GATEWAY
-#define CONFIG_BOOTP_HOSTNAME
-
-/*
- * Command line configuration.
- */
-#define CONFIG_CMD_CACHE
-
-/*
- * Additional command
- */
-#define CONFIG_CMD_DHCP
-#define CONFIG_CMD_PING
-#define CONFIG_CMD_ELF
-#define CONFIG_CMD_FAT
-#define CONFIG_CMD_USB
-
-#define CONFIG_SYS_HUSH_PARSER
 
 /*
  * USB
  */
 #ifdef CONFIG_CMD_USB
-#define CONFIG_USB_EHCI                        /* Enable EHCI USB support */
 #define CONFIG_USB_EHCI_MXC
 #define CONFIG_EHCI_HCD_INIT_AFTER_RESET
 #define CONFIG_MXC_USB_PORT    1
 #define CONFIG_MXC_USB_PORTSC  MXC_EHCI_MODE_SERIAL
 #define CONFIG_MXC_USB_FLAGS   (MXC_EHCI_INTERNAL_PHY | MXC_EHCI_IPPUE_DOWN)
 #define CONFIG_EHCI_IS_TDI
-#define CONFIG_USB_STORAGE
-#define CONFIG_DOS_PARTITION
-#define CONFIG_SUPPORT_VFAT
 #endif /* CONFIG_CMD_USB */
 
 /* SDRAM */
-#define CONFIG_NR_DRAM_BANKS   1
 #define PHYS_SDRAM             0x80000000      /* start address of LPDDRRAM */
 #define PHYS_SDRAM_SIZE                0x04000000      /* 64 megs */
 
@@ -121,34 +77,12 @@
 #define CONFIG_SYS_MAX_FLASH_BANKS     1
 #define CONFIG_SYS_MAX_FLASH_SECT      256
 
-#define CONFIG_ENV_ADDR                        (CONFIG_SYS_FLASH_BASE + 0x00040000)
-#define CONFIG_ENV_IS_IN_FLASH         1
-#define CONFIG_ENV_SECT_SIZE           (128 * 1024)
-#define CONFIG_ENV_SIZE                        (128 * 1024)
-
 /*
  * CFI FLASH driver setup
  */
-#define CONFIG_SYS_FLASH_CFI
-#define CONFIG_FLASH_CFI_DRIVER
-#define CONFIG_SYS_FLASH_USE_BUFFER_WRITE      /* ~10x faster */
 
 #define CONFIG_SYS_LOAD_ADDR           CONFIG_SYS_SDRAM_BASE
 
-#define CONFIG_SYS_MEMTEST_START       (PHYS_SDRAM + (512*1024))
-#define CONFIG_SYS_MEMTEST_END         (PHYS_SDRAM + PHYS_SDRAM_SIZE)
-
-#define CONFIG_SYS_PROMPT      "zmx25> "
-#define CONFIG_SYS_CBSIZE      256
-#define CONFIG_SYS_MAXARGS     16
-#define CONFIG_SYS_PBSIZE      (CONFIG_SYS_CBSIZE + \
-                               sizeof(CONFIG_SYS_PROMPT) + 16)
-#define CONFIG_SYS_LONGHELP
-#define CONFIG_CMDLINE_EDITING
-
-#define CONFIG_PREBOOT  ""
-
-#define CONFIG_BOOTDELAY       5
 
 /*
  * Size of malloc() pool