include/configs: drop default definitions of CONFIG_SYS_PBSIZE

[platform/kernel/u-boot.git] / include / configs / xpedite550x.h

diff --git a/include/configs/xpedite550x.h b/include/configs/xpedite550x.h
index 276dde7..97669f3 100644 (file)
--- a/include/configs/xpedite550x.h
+++ b/include/configs/xpedite550x.h
@@ -14,30 +14,22 @@
 /*
  * High Level Configuration Options
  */
-#define CONFIG_BOOKE           1       /* BOOKE */
-#define CONFIG_E500            1       /* BOOKE e500 family */
-#define CONFIG_P2020           1
 #define CONFIG_XPEDITE550X     1
 #define CONFIG_SYS_BOARD_NAME  "XPedite5500"
 #define CONFIG_SYS_FORM_PMC_XMC        1
 #define CONFIG_PRPMC_PCI_ALIAS "pci0"  /* Processor PMC interface on pci0 */
 #define CONFIG_BOARD_EARLY_INIT_R      /* Call board_pre_init */
-#define CONFIG_DISPLAY_BOARDINFO
 
 #ifndef CONFIG_SYS_TEXT_BASE
 #define CONFIG_SYS_TEXT_BASE   0xfff80000
 #endif
 
-#define CONFIG_PCI             1       /* Enable PCI/PCIE */
-#define CONFIG_PCI_PNP         1       /* do pci plug-and-play */
 #define CONFIG_PCI_SCAN_SHOW   1       /* show pci devices on startup */
 #define CONFIG_PCIE1           1       /* PCIE controller 1 (PEX8112 or XMC) */
 #define CONFIG_FSL_PCI_INIT    1       /* Use common FSL init code */
 #define CONFIG_PCI_INDIRECT_BRIDGE 1   /* indirect PCI bridge support */
 #define CONFIG_SYS_PCI_64BIT   1       /* enable 64-bit PCI resources */
 #define CONFIG_FSL_PCIE_RESET  1       /* need PCIe reset errata */
-#define CONFIG_FSL_LAW         1       /* Use common FSL init code */
-#define CONFIG_FSL_ELBC                1
 
 /*
  * Multicore config
@@ -49,13 +41,11 @@
 /*
  * DDR config
  */
-#define CONFIG_SYS_FSL_DDR3
 #define CONFIG_SPD_EEPROM              /* Use SPD EEPROM for DDR setup */
 #define CONFIG_DDR_SPD
 #define CONFIG_MEM_INIT_VALUE          0xdeadbeef
 #define SPD_EEPROM_ADDRESS                     0x54
 #define SPD_EEPROM_OFFSET              0x200   /* OFFSET of SPD in EEPROM */
-#define CONFIG_NUM_DDR_CONTROLLERS     1
 #define CONFIG_DIMM_SLOTS_PER_CTLR     1
 #define CONFIG_CHIP_SELECTS_PER_CTRL 2
 #define CONFIG_DDR_ECC
@@ -211,7 +201,6 @@ extern unsigned long get_board_ddr_clk(unsigned long dummy);
 #define CONFIG_SYS_NS16550_COM2        (CONFIG_SYS_CCSRBAR+0x4600)
 #define CONFIG_SYS_BAUDRATE_TABLE      \
        {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 115200}
-#define CONFIG_BAUDRATE                        115200
 #define CONFIG_LOADS_ECHO              1       /* echo on for serial download */
 #define CONFIG_SYS_LOADS_BAUD_CHANGE   1       /* allow baudrate change */
 
@@ -230,8 +219,6 @@ extern unsigned long get_board_ddr_clk(unsigned long dummy);
 #define CONFIG_SYS_FSL_I2C2_OFFSET     0x3100
 
 /* I2C DS7505 temperature sensor */
-#define CONFIG_DTT_LM75
-#define CONFIG_DTT_SENSORS             { 0 }
 #define CONFIG_SYS_I2C_LM75_ADDR       0x48
 
 /* I2C ADT7461 temperature sensor */
@@ -303,7 +290,6 @@ extern unsigned long get_board_ddr_clk(unsigned long dummy);
  * Networking options
  */
 #define CONFIG_TSEC_ENET               /* tsec ethernet support */
-#define CONFIG_PHY_GIGE                1       /* Include GbE speed/duplex detection */
 #define CONFIG_TSEC_TBI
 #define CONFIG_MII             1       /* MII PHY management */
 #define CONFIG_MII_DEFAULT_TSEC        1       /* Allow unregistered phys */
@@ -343,33 +329,14 @@ extern unsigned long get_board_ddr_clk(unsigned long dummy);
 /*
  * USB
  */
-#define CONFIG_USB_STORAGE
-#define CONFIG_USB_EHCI
 #define CONFIG_USB_EHCI_FSL
 #define CONFIG_EHCI_HCD_INIT_AFTER_RESET
-#define CONFIG_DOS_PARTITION
-
-/*
- * Command configuration.
- */
-#define CONFIG_CMD_DATE
-#define CONFIG_CMD_DTT
-#define CONFIG_CMD_EEPROM
-#define CONFIG_CMD_JFFS2
-#define CONFIG_CMD_NAND
-#define CONFIG_CMD_PCA953X
-#define CONFIG_CMD_PCA953X_INFO
-#define CONFIG_CMD_PCI
-#define CONFIG_CMD_PCI_ENUM
-#define CONFIG_CMD_REGINFO
 
 /*
  * Miscellaneous configurable options
  */
 #define CONFIG_SYS_LONGHELP                    /* undef to save memory */
 #define CONFIG_SYS_LOAD_ADDR   0x2000000       /* default load address */
-#define CONFIG_SYS_CBSIZE      256             /* Console I/O Buffer Size */
-#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */
 #define CONFIG_SYS_MAXARGS     16              /* max number of command args */
 #define CONFIG_SYS_BARGSIZE    CONFIG_SYS_CBSIZE       /* Boot Argument Buffer Size */
 #define CONFIG_CMDLINE_EDITING 1               /* add command line history     */
@@ -390,7 +357,6 @@ extern unsigned long get_board_ddr_clk(unsigned long dummy);
 /*
  * Environment Configuration
  */
-#define CONFIG_ENV_IS_IN_FLASH 1
 #define CONFIG_ENV_SECT_SIZE   0x20000         /* 128k (one sector) for env */
 #define CONFIG_ENV_SIZE                0x8000
 #define CONFIG_ENV_ADDR                (CONFIG_SYS_MONITOR_BASE - (256 * 1024))