+++ /dev/null
-/*
- * (C) Copyright 2002 Scott McNutt <smcnutt@artesyncp.com>
- *
- * SPDX-License-Identifier: GPL-2.0+
- */
-
-/*
- * config for XPedite1000 from XES Inc.
- * Ported from EBONY config by Travis B. Sawyer <tsawyer@sandburst.com>
- * (C) Copyright 2003 Sandburst Corporation
- * board/config_EBONY.h - configuration for AMCC 440GP Ref (Ebony)
- */
-
-#ifndef __CONFIG_H
-#define __CONFIG_H
-
-/* High Level Configuration Options */
-#define CONFIG_XPEDITE1000 1
-#define CONFIG_SYS_BOARD_NAME "XPedite1000"
-#define CONFIG_SYS_FORM_PMC 1
-#define CONFIG_440 1
-#define CONFIG_440GX 1 /* 440 GX */
-#define CONFIG_BOARD_EARLY_INIT_F 1 /* Call board_pre_init */
-#define CONFIG_SYS_CLK_FREQ 33333333 /* external freq to pll */
-
-#define CONFIG_SYS_TEXT_BASE 0xFFF80000
-
-/*
- * DDR config
- */
-#define CONFIG_SPD_EEPROM /* Use SPD EEPROM for setup */
-#define SPD_EEPROM_ADDRESS {0x54} /* SPD i2c spd addresses */
-#define CONFIG_VERY_BIG_RAM 1
-
-/*
- * Base addresses -- Note these are effective addresses where the
- * actual resources get mapped (not physical addresses)
- */
-#define CONFIG_SYS_SDRAM_BASE 0x00000000
-#define CONFIG_SYS_FLASH_BASE 0xff000000 /* start of FLASH */
-#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE /* start of monitor */
-#define CONFIG_SYS_PCI_MEMBASE 0x80000000 /* mapped pci memory */
-#define CONFIG_SYS_ISRAM_BASE 0xc0000000 /* internal SRAM */
-#define CONFIG_SYS_PCI_BASE 0xd0000000 /* internal PCI regs */
-#define CONFIG_SYS_NVRAM_BASE_ADDR (CONFIG_SYS_PERIPHERAL_BASE + 0x08000000)
-#define CONFIG_SYS_GPIO_BASE (CONFIG_SYS_PERIPHERAL_BASE + 0x00000700)
-
-/*
- * Diagnostics
- */
-#define CONFIG_SYS_ALT_MEMTEST
-#define CONFIG_SYS_MEMTEST_START 0x0400000
-#define CONFIG_SYS_MEMTEST_END 0x0C00000
-
-/* POST support */
-#define CONFIG_POST (CONFIG_SYS_POST_RTC | \
- CONFIG_SYS_POST_I2C)
-
-/*
- * LED support
- */
-#define USR_LED0 0x00000080
-#define USR_LED1 0x00000100
-#define USR_LED2 0x00000200
-#define USR_LED3 0x00000400
-
-#ifndef __ASSEMBLY__
-extern unsigned long in32(unsigned int);
-extern void out32(unsigned int, unsigned long);
-
-#define LED0_ON() out32(CONFIG_SYS_GPIO_BASE, (in32(CONFIG_SYS_GPIO_BASE) & ~USR_LED0))
-#define LED1_ON() out32(CONFIG_SYS_GPIO_BASE, (in32(CONFIG_SYS_GPIO_BASE) & ~USR_LED1))
-#define LED2_ON() out32(CONFIG_SYS_GPIO_BASE, (in32(CONFIG_SYS_GPIO_BASE) & ~USR_LED2))
-#define LED3_ON() out32(CONFIG_SYS_GPIO_BASE, (in32(CONFIG_SYS_GPIO_BASE) & ~USR_LED3))
-
-#define LED0_OFF() out32(CONFIG_SYS_GPIO_BASE, (in32(CONFIG_SYS_GPIO_BASE) | USR_LED0))
-#define LED1_OFF() out32(CONFIG_SYS_GPIO_BASE, (in32(CONFIG_SYS_GPIO_BASE) | USR_LED1))
-#define LED2_OFF() out32(CONFIG_SYS_GPIO_BASE, (in32(CONFIG_SYS_GPIO_BASE) | USR_LED2))
-#define LED3_OFF() out32(CONFIG_SYS_GPIO_BASE, (in32(CONFIG_SYS_GPIO_BASE) | USR_LED3))
-#endif
-
-/*
- * Use internal SRAM for initial stack
- */
-#define CONFIG_SYS_TEMP_STACK_OCM 1
-#define CONFIG_SYS_OCM_DATA_ADDR CONFIG_SYS_ISRAM_BASE
-#define CONFIG_SYS_INIT_RAM_ADDR CONFIG_SYS_ISRAM_BASE /* Initial RAM address */
-#define CONFIG_SYS_INIT_RAM_SIZE 0x2000 /* Size of used area in RAM */
-#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
-#define CONFIG_SYS_INIT_SP_OFFSET (CONFIG_SYS_GBL_DATA_OFFSET - 0x4)
-
-#define CONFIG_SYS_MONITOR_LEN (512 * 1024) /* Reserve 512 KB for Mon */
-#define CONFIG_SYS_MALLOC_LEN (1024 * 1024) /* Reserved for malloc */
-
-/*
- * Serial Port
- */
-#define CONFIG_CONS_INDEX 1 /* Use UART0 */
-#define CONFIG_SYS_NS16550_SERIAL
-#define CONFIG_SYS_NS16550_REG_SIZE 1
-#define CONFIG_SYS_NS16550_CLK get_serial_clock()
-
-#define CONFIG_SYS_BAUDRATE_TABLE \
- {300, 600, 1200, 2400, 4800, 9600, 19200, 38400}
-#define CONFIG_BAUDRATE 115200
-#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */
-#define CONFIG_SYS_LOADS_BAUD_CHANGE 1 /* allow baudrate change */
-
-/*
- * NOR flash configuration
- */
-#define CONFIG_SYS_MAX_FLASH_BANKS 3
-#define CONFIG_SYS_FLASH_BANKS_LIST {CONFIG_SYS_FLASH_BASE, 0xf0000000, 0xf4000000 }
-#define CONFIG_SYS_MAX_FLASH_SECT 512 /* sectors per device */
-#define CONFIG_FLASH_CFI_DRIVER
-#define CONFIG_SYS_FLASH_CFI
-#define CONFIG_SYS_FLASH_USE_BUFFER_WRITE
-#define CONFIG_SYS_FLASH_QUIET_TEST /* MirrorBit flashes are optional */
-#define CONFIG_SYS_FLASH_ERASE_TOUT 120000 /* Timeout for Flash Erase (in ms) */
-#define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Timeout for Flash Write (in ms) */
-
-/*
- * I2C
- */
-#define CONFIG_SYS_I2C
-#define CONFIG_SYS_I2C_PPC4XX
-#define CONFIG_SYS_I2C_PPC4XX_CH0
-#define CONFIG_SYS_I2C_PPC4XX_SPEED_0 400000
-#define CONFIG_SYS_I2C_PPC4XX_SLAVE_0 0x7f
-
-/* I2C EEPROM */
-#define CONFIG_SYS_I2C_EEPROM_ADDR 0x50
-#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1
-#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 3
-#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 10
-
-/* I2C RTC: STMicro M41T00 */
-#define CONFIG_RTC_M41T11 1
-#define CONFIG_SYS_I2C_RTC_ADDR 0x68
-#define CONFIG_SYS_M41T11_BASE_YEAR 2000
-
-/*
- * PCI
- */
-/* General PCI */
-#define CONFIG_PCI /* include pci support */
-#define CONFIG_PCI_INDIRECT_BRIDGE /* indirect PCI bridge support */
-#define CONFIG_PCI_PNP /* do pci plug-and-play */
-#define CONFIG_PCI_SCAN_SHOW /* show pci devices on startup */
-#define CONFIG_SYS_PCI_TARGBASE 0x80000000 /* PCIaddr mapped to CONFIG_SYS_PCI_MEMBASE */
-
-/* Board-specific PCI */
-#define CONFIG_SYS_PCI_TARGET_INIT /* let board init pci target */
-#define CONFIG_SYS_PCI_SUBSYS_VENDORID 0x1014 /* IBM */
-#define CONFIG_SYS_PCI_SUBSYS_DEVICEID 0xcafe /* Whatever */
-#define CONFIG_SYS_PCI_FORCE_PCI_CONV /* Force PCI Conventional Mode */
-
-/*
- * Networking options
- */
-#define CONFIG_PPC4xx_EMAC
-#define CONFIG_PHY_GIGE 1 /* Include GbE speed/duplex detection */
-#define CONFIG_MII 1 /* MII PHY management */
-#define CONFIG_PHY_RESET 1 /* reset phy upon startup */
-#define CONFIG_SYS_RX_ETH_BUFFER 32 /* Number of ethernet rx buffers & descriptors */
-#define CONFIG_ETHPRIME "ppc_4xx_eth2"
-#define CONFIG_PHY_ADDR 4 /* PHY address phy0 not populated */
-#define CONFIG_PHY2_ADDR 4 /* PHY address phy2 */
-#define CONFIG_HAS_ETH2 1 /* add support for "eth2addr" */
-#define CONFIG_PHY3_ADDR 8 /* PHY address phy3 */
-#define CONFIG_HAS_ETH3 1 /* add support for "eth3addr" */
-
-/* BOOTP options */
-#define CONFIG_BOOTP_BOOTFILESIZE
-#define CONFIG_BOOTP_BOOTPATH
-#define CONFIG_BOOTP_GATEWAY
-#define CONFIG_BOOTP_HOSTNAME
-
-/*
- * Command configuration
- */
-#define CONFIG_CMD_DATE
-#define CONFIG_CMD_EEPROM
-#define CONFIG_CMD_IRQ
-#define CONFIG_CMD_JFFS2
-#define CONFIG_CMD_PCI
-
-/*
- * Miscellaneous configurable options
- */
-#define CONFIG_SYS_LONGHELP /* undef to save memory */
-#define CONFIG_SYS_LOAD_ADDR 0x100000 /* default load address */
-#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */
-#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */
-#define CONFIG_SYS_MAXARGS 16 /* max number of command args */
-#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */
-#define CONFIG_CMDLINE_EDITING 1 /* Command-line editing */
-#define CONFIG_PANIC_HANG /* do not reset board on panic */
-#define CONFIG_PREBOOT /* enable preboot variable */
-#define CONFIG_INTEGRITY /* support booting INTEGRITY OS */
-#define CONFIG_SYS_EXTBDINFO 1 /* To use extended board_into (bd_t) */
-
-/*
- * For booting Linux, the board info and command line data
- * have to be in the first 8 MB of memory, since this is
- * the maximum mapped by the Linux kernel during initialization.
- */
-#define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */
-
-/*
- * Environment Configuration
- */
-#define CONFIG_ENV_IS_IN_FLASH 1
-#define CONFIG_ENV_SECT_SIZE 0x20000 /* 128k (one sector) for env */
-#define CONFIG_ENV_SIZE 0x8000
-#define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE - (256 * 1024))
-
-/*
- * Flash memory map:
- * fff80000 - ffffffff U-Boot (512 KB)
- * fff40000 - fff7ffff U-Boot Environment (256 KB)
- * fff00000 - fff3ffff FDT (256KB)
- * ffc00000 - ffefffff OS image (3MB)
- * ff000000 - ffbfffff OS Use/Filesystem (12MB)
- */
-
-#define CONFIG_UBOOT_ENV_ADDR __stringify(CONFIG_SYS_TEXT_BASE)
-#define CONFIG_FDT_ENV_ADDR __stringify(0xfff00000)
-#define CONFIG_OS_ENV_ADDR __stringify(0xffc00000)
-
-#define CONFIG_PROG_UBOOT \
- "$download_cmd $loadaddr $ubootfile; " \
- "if test $? -eq 0; then " \
- "protect off "CONFIG_UBOOT_ENV_ADDR" +80000; " \
- "erase "CONFIG_UBOOT_ENV_ADDR" +80000; " \
- "cp.w $loadaddr "CONFIG_UBOOT_ENV_ADDR" 40000; " \
- "protect on "CONFIG_UBOOT_ENV_ADDR" +80000; " \
- "cmp.b $loadaddr "CONFIG_UBOOT_ENV_ADDR" 80000; " \
- "if test $? -ne 0; then " \
- "echo PROGRAM FAILED; " \
- "else; " \
- "echo PROGRAM SUCCEEDED; " \
- "fi; " \
- "else; " \
- "echo DOWNLOAD FAILED; " \
- "fi;"
-
-#define CONFIG_BOOT_OS_NET \
- "$download_cmd $osaddr $osfile; " \
- "if test $? -eq 0; then " \
- "if test -n $fdtaddr; then " \
- "$download_cmd $fdtaddr $fdtfile; " \
- "if test $? -eq 0; then " \
- "bootm $osaddr - $fdtaddr; " \
- "else; " \
- "echo FDT DOWNLOAD FAILED; " \
- "fi; " \
- "else; " \
- "bootm $osaddr; " \
- "fi; " \
- "else; " \
- "echo OS DOWNLOAD FAILED; " \
- "fi;"
-
-#define CONFIG_PROG_OS \
- "$download_cmd $osaddr $osfile; " \
- "if test $? -eq 0; then " \
- "erase "CONFIG_OS_ENV_ADDR" +$filesize; " \
- "cp.b $osaddr "CONFIG_OS_ENV_ADDR" $filesize; " \
- "cmp.b $osaddr "CONFIG_OS_ENV_ADDR" $filesize; " \
- "if test $? -ne 0; then " \
- "echo OS PROGRAM FAILED; " \
- "else; " \
- "echo OS PROGRAM SUCCEEDED; " \
- "fi; " \
- "else; " \
- "echo OS DOWNLOAD FAILED; " \
- "fi;"
-
-#define CONFIG_PROG_FDT \
- "$download_cmd $fdtaddr $fdtfile; " \
- "if test $? -eq 0; then " \
- "erase "CONFIG_FDT_ENV_ADDR" +$filesize;" \
- "cp.b $fdtaddr "CONFIG_FDT_ENV_ADDR" $filesize; " \
- "cmp.b $fdtaddr "CONFIG_FDT_ENV_ADDR" $filesize; " \
- "if test $? -ne 0; then " \
- "echo FDT PROGRAM FAILED; " \
- "else; " \
- "echo FDT PROGRAM SUCCEEDED; " \
- "fi; " \
- "else; " \
- "echo FDT DOWNLOAD FAILED; " \
- "fi;"
-
-#define CONFIG_EXTRA_ENV_SETTINGS \
- "autoload=yes\0" \
- "download_cmd=tftp\0" \
- "console_args=console=ttyS0,115200\0" \
- "root_args=root=/dev/nfs rw\0" \
- "misc_args=ip=on\0" \
- "set_bootargs=setenv bootargs ${console_args} ${root_args} ${misc_args}\0" \
- "bootfile=/home/user/file\0" \
- "osfile=/home/user/board.uImage\0" \
- "fdtfile=/home/user/board.dtb\0" \
- "ubootfile=/home/user/u-boot.bin\0" \
- "fdtaddr=0x1e00000\0" \
- "osaddr=0x1000000\0" \
- "loadaddr=0x1000000\0" \
- "prog_uboot="CONFIG_PROG_UBOOT"\0" \
- "prog_os="CONFIG_PROG_OS"\0" \
- "prog_fdt="CONFIG_PROG_FDT"\0" \
- "bootcmd_net=run set_bootargs; "CONFIG_BOOT_OS_NET"\0" \
- "bootcmd_flash=run set_bootargs; " \
- "bootm "CONFIG_OS_ENV_ADDR" - "CONFIG_FDT_ENV_ADDR"\0" \
- "bootcmd=run bootcmd_flash\0"
-#endif /* __CONFIG_H */
projects / platform / kernel / u-boot.git / blobdiff