+++ /dev/null
-/*
- * Copyright (C) 2009, STMicroelectronics - All Rights Reserved
- * Author(s): Vipin Kumar, <vipin.kumar@st.com> for STMicroelectronics.
- *
- * Copyright (C) 2012, 2015 Stefan Roese <sr@denx.de>
- *
- * SPDX-License-Identifier: GPL-2.0+
- */
-
-#ifndef __CONFIG_H
-#define __CONFIG_H
-
-/*
- * High Level Configuration Options
- * (easy to change)
- */
-#define CONFIG_SPEAR600 /* SPEAr600 SoC */
-#define CONFIG_X600 /* on X600 board */
-
-#include <asm/arch/hardware.h>
-
-/* Timer, HZ specific defines */
-#define CONFIG_SYS_HZ_CLOCK 8300000
-
-#define CONFIG_SYS_FLASH_BASE 0xf8000000
-/* Reserve 8KiB for SPL */
-#define CONFIG_SPL_PAD_TO 8192 /* decimal for 'dd' */
-#define CONFIG_SYS_SPL_LEN CONFIG_SPL_PAD_TO
-#define CONFIG_SYS_UBOOT_BASE (CONFIG_SYS_FLASH_BASE + \
- CONFIG_SYS_SPL_LEN)
-#define CONFIG_SYS_UBOOT_START CONFIG_SYS_TEXT_BASE
-#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_FLASH_BASE
-#define CONFIG_SYS_MONITOR_LEN 0x60000
-
-/* Serial Configuration (PL011) */
-#define CONFIG_SYS_SERIAL0 0xD0000000
-#define CONFIG_SYS_SERIAL1 0xD0080000
-#define CONFIG_PL01x_PORTS { (void *)CONFIG_SYS_SERIAL0, \
- (void *)CONFIG_SYS_SERIAL1 }
-#define CONFIG_PL011_CLOCK (48 * 1000 * 1000)
-#define CONFIG_CONS_INDEX 0
-#define CONFIG_SYS_BAUDRATE_TABLE { 9600, 19200, 38400, \
- 57600, 115200 }
-#define CONFIG_SYS_LOADS_BAUD_CHANGE
-
-/* NOR FLASH config options */
-#define CONFIG_ST_SMI
-#define CONFIG_SYS_MAX_FLASH_BANKS 1
-#define CONFIG_SYS_FLASH_BANK_SIZE 0x01000000
-#define CONFIG_SYS_FLASH_ADDR_BASE { CONFIG_SYS_FLASH_BASE }
-#define CONFIG_SYS_MAX_FLASH_SECT 128
-#define CONFIG_SYS_FLASH_EMPTY_INFO
-#define CONFIG_SYS_FLASH_ERASE_TOUT (3 * CONFIG_SYS_HZ)
-#define CONFIG_SYS_FLASH_WRITE_TOUT (3 * CONFIG_SYS_HZ)
-
-/* NAND FLASH config options */
-#define CONFIG_NAND_FSMC
-#define CONFIG_SYS_NAND_SELF_INIT
-#define CONFIG_SYS_MAX_NAND_DEVICE 1
-#define CONFIG_SYS_NAND_BASE CONFIG_FSMC_NAND_BASE
-#define CONFIG_MTD_ECC_SOFT
-#define CONFIG_SYS_FSMC_NAND_8BIT
-#define CONFIG_SYS_NAND_ONFI_DETECTION
-#define CONFIG_NAND_ECC_BCH
-
-/* UBI/UBI config options */
-#define CONFIG_MTD_DEVICE
-#define CONFIG_MTD_PARTITIONS
-
-/* Ethernet config options */
-#define CONFIG_MII
-#define CONFIG_PHY_RESET_DELAY 10000 /* in usec */
-#define CONFIG_PHY_ADDR 0 /* PHY address */
-
-#define CONFIG_SPEAR_GPIO
-
-/* I2C config options */
-#define CONFIG_SYS_I2C
-#define CONFIG_SYS_I2C_BASE 0xD0200000
-#define CONFIG_SYS_I2C_SPEED 400000
-#define CONFIG_SYS_I2C_SLAVE 0x02
-#define CONFIG_I2C_CHIPADDRESS 0x50
-
-#define CONFIG_RTC_M41T62 1
-#define CONFIG_SYS_I2C_RTC_ADDR 0x68
-
-/* FPGA config options */
-#define CONFIG_FPGA_SPARTAN3
-#define CONFIG_FPGA_COUNT 1
-
-/* USB EHCI options */
-#define CONFIG_USB_EHCI_SPEAR
-#define CONFIG_USB_MAX_CONTROLLER_COUNT 2
-
-/*
- * U-Boot Environment placing definitions.
- */
-#define CONFIG_ENV_SECT_SIZE 0x00010000
-#define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE + \
- CONFIG_SYS_MONITOR_LEN)
-#define CONFIG_ENV_SIZE 0x02000
-#define CONFIG_ENV_ADDR_REDUND (CONFIG_ENV_ADDR + \
- CONFIG_ENV_SECT_SIZE)
-#define CONFIG_ENV_SIZE_REDUND (CONFIG_ENV_SIZE)
-
-/* Miscellaneous configurable options */
-#define CONFIG_ARCH_CPU_INIT
-#define CONFIG_BOOT_PARAMS_ADDR 0x00000100
-#define CONFIG_CMDLINE_TAG
-#define CONFIG_SETUP_MEMORY_TAGS
-#define CONFIG_MISC_INIT_R
-#define CONFIG_MX_CYCLIC /* enable mdc/mwc commands */
-
-#define CONFIG_SYS_MEMTEST_START 0x00800000
-#define CONFIG_SYS_MEMTEST_END 0x04000000
-#define CONFIG_SYS_MALLOC_LEN (8 << 20)
-#define CONFIG_SYS_LOAD_ADDR 0x00800000
-
-#define CONFIG_HOSTNAME x600
-#define CONFIG_UBI_PART ubi0
-#define CONFIG_UBIFS_VOLUME rootfs
-
-#define CONFIG_EXTRA_ENV_SETTINGS \
- "u-boot_addr=1000000\0" \
- "u-boot=" __stringify(CONFIG_HOSTNAME) "/u-boot.spr\0" \
- "load=tftp ${u-boot_addr} ${u-boot}\0" \
- "update=protect off " __stringify(CONFIG_SYS_MONITOR_BASE) \
- " +${filesize};" \
- "erase " __stringify(CONFIG_SYS_MONITOR_BASE) " +${filesize};" \
- "cp.b ${u-boot_addr} " __stringify(CONFIG_SYS_MONITOR_BASE) \
- " ${filesize};" \
- "protect on " __stringify(CONFIG_SYS_MONITOR_BASE) \
- " +${filesize}\0" \
- "upd=run load update\0" \
- "ubifs=" __stringify(CONFIG_HOSTNAME) "/ubifs.img\0" \
- "part=" __stringify(CONFIG_UBI_PART) "\0" \
- "vol=" __stringify(CONFIG_UBIFS_VOLUME) "\0" \
- "load_ubifs=tftp ${kernel_addr} ${ubifs}\0" \
- "update_ubifs=ubi part ${part};ubi write ${kernel_addr} ${vol}" \
- " ${filesize}\0" \
- "upd_ubifs=run load_ubifs update_ubifs\0" \
- "init_ubifs=nand erase.part ubi0;ubi part ${part};" \
- "ubi create ${vol} 4000000\0" \
- "netdev=eth0\0" \
- "rootpath=/opt/eldk-4.2/arm\0" \
- "nfsargs=setenv bootargs root=/dev/nfs rw " \
- "nfsroot=${serverip}:${rootpath}\0" \
- "ramargs=setenv bootargs root=/dev/ram rw\0" \
- "boot_part=0\0" \
- "altbootcmd=if test $boot_part -eq 0;then " \
- "echo Switching to partition 1!;" \
- "setenv boot_part 1;" \
- "else; " \
- "echo Switching to partition 0!;" \
- "setenv boot_part 0;" \
- "fi;" \
- "saveenv;boot\0" \
- "ubifsargs=set bootargs ubi.mtd=ubi${boot_part} " \
- "root=ubi0:rootfs rootfstype=ubifs\0" \
- "kernel=" __stringify(CONFIG_HOSTNAME) "/uImage\0" \
- "kernel_fs=/boot/uImage \0" \
- "kernel_addr=1000000\0" \
- "dtb=" __stringify(CONFIG_HOSTNAME) "/" \
- __stringify(CONFIG_HOSTNAME) ".dtb\0" \
- "dtb_fs=/boot/" __stringify(CONFIG_HOSTNAME) ".dtb\0" \
- "dtb_addr=1800000\0" \
- "load_kernel=tftp ${kernel_addr} ${kernel}\0" \
- "load_dtb=tftp ${dtb_addr} ${dtb}\0" \
- "addip=setenv bootargs ${bootargs} " \
- "ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}" \
- ":${hostname}:${netdev}:off panic=1\0" \
- "addcon=setenv bootargs ${bootargs} console=ttyAMA0," \
- "${baudrate}\0" \
- "addmtd=setenv bootargs ${bootargs} ${mtdparts}\0" \
- "net_nfs=run load_dtb load_kernel; " \
- "run nfsargs addip addcon addmtd addmisc;" \
- "bootm ${kernel_addr} - ${dtb_addr}\0" \
- "mtdids=" CONFIG_MTDIDS_DEFAULT "\0" \
- "mtdparts=" CONFIG_MTDPARTS_DEFAULT "\0" \
- "nand_ubifs=run ubifs_mount ubifs_load ubifsargs addip" \
- " addcon addmisc addmtd;" \
- "bootm ${kernel_addr} - ${dtb_addr}\0" \
- "ubifs_mount=ubi part ubi${boot_part};ubifsmount ubi:rootfs\0" \
- "ubifs_load=ubifsload ${kernel_addr} ${kernel_fs};" \
- "ubifsload ${dtb_addr} ${dtb_fs};\0" \
- "nand_ubifs=run ubifs_mount ubifs_load ubifsargs addip addcon " \
- "addmtd addmisc;bootm ${kernel_addr} - ${dtb_addr}\0" \
- "bootcmd=run nand_ubifs\0" \
- "\0"
-
-/* Physical Memory Map */
-#define CONFIG_NR_DRAM_BANKS 1
-#define PHYS_SDRAM_1 0x00000000
-#define PHYS_SDRAM_1_MAXSIZE 0x40000000
-
-#define CONFIG_SYS_SDRAM_BASE PHYS_SDRAM_1
-#define CONFIG_SRAM_BASE 0xd2800000
-/* Preserve the last 2 lwords for the boot-counter */
-#define CONFIG_SRAM_SIZE ((8 << 10) - 0x8)
-#define CONFIG_SYS_INIT_RAM_ADDR CONFIG_SRAM_BASE
-#define CONFIG_SYS_INIT_RAM_SIZE CONFIG_SRAM_SIZE
-
-#define CONFIG_SYS_INIT_SP_OFFSET \
- (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
-
-#define CONFIG_SYS_INIT_SP_ADDR \
- (CONFIG_SYS_INIT_RAM_ADDR + CONFIG_SYS_INIT_SP_OFFSET)
-
-/*
- * SPL related defines
- */
-#define CONFIG_SPL_TEXT_BASE 0xd2800b00
-#define CONFIG_SPL_MAX_SIZE (CONFIG_SRAM_SIZE - 0xb00)
-#define CONFIG_SPL_START_S_PATH "arch/arm/cpu/arm926ejs/spear"
-
-/*
- * Please select/define only one of the following
- * Each definition corresponds to a supported DDR chip.
- * DDR configuration is based on the following selection
- */
-#define CONFIG_DDR_MT47H64M16 1
-#define CONFIG_DDR_MT47H32M16 0
-#define CONFIG_DDR_MT47H128M8 0
-
-/*
- * Synchronous/Asynchronous operation of DDR
- *
- * Select CONFIG_DDR_2HCLK for DDR clk = 333MHz, synchronous operation
- * Select CONFIG_DDR_HCLK for DDR clk = 166MHz, synchronous operation
- * Select CONFIG_DDR_PLL2 for DDR clk = PLL2, asynchronous operation
- */
-#define CONFIG_DDR_2HCLK 1
-#define CONFIG_DDR_HCLK 0
-#define CONFIG_DDR_PLL2 0
-
-/*
- * xxx_BOOT_SUPPORTED macro defines whether a booting type is supported
- * or not. Modify/Add to only these macros to define new boot types
- */
-#define USB_BOOT_SUPPORTED 0
-#define PCIE_BOOT_SUPPORTED 0
-#define SNOR_BOOT_SUPPORTED 1
-#define NAND_BOOT_SUPPORTED 1
-#define PNOR_BOOT_SUPPORTED 0
-#define TFTP_BOOT_SUPPORTED 0
-#define UART_BOOT_SUPPORTED 0
-#define SPI_BOOT_SUPPORTED 0
-#define I2C_BOOT_SUPPORTED 0
-#define MMC_BOOT_SUPPORTED 0
-
-#endif /* __CONFIG_H */
projects / platform / kernel / u-boot.git / blobdiff