Prepare v2023.10
[platform/kernel/u-boot.git] / include / configs / verdin-imx8mp.h
index 766707d..942081a 100644 (file)
@@ -9,58 +9,32 @@
 #include <asm/arch/imx-regs.h>
 #include <linux/sizes.h>
 
-#define CONFIG_SPL_MAX_SIZE                            (152 * 1024)
-#define CONFIG_SYS_MONITOR_LEN                         SZ_512K
-#define CONFIG_SYS_UBOOT_BASE  \
+#define CFG_SYS_UBOOT_BASE     \
        (QSPI0_AMBA_BASE + CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR * 512)
 
 #ifdef CONFIG_SPL_BUILD
 /*#define CONFIG_ENABLE_DDR_TRAINING_DEBUG*/
-#define CONFIG_SPL_STACK               0x960000
-#define CONFIG_SPL_BSS_START_ADDR      0x0098fc00
-#define CONFIG_SPL_BSS_MAX_SIZE                SZ_1K
-#define CONFIG_SYS_SPL_MALLOC_START    0x42200000
-#define CONFIG_SYS_SPL_MALLOC_SIZE     SZ_512K
 
 /* malloc f used before GD_FLG_FULL_MALLOC_INIT set */
-#define CONFIG_MALLOC_F_ADDR                           0x184000
+#define CFG_MALLOC_F_ADDR                              0x184000
 /* For RAW image gives a error info not panic */
-#define CONFIG_SPL_ABORT_ON_RAW_IMAGE
 
-#define CONFIG_POWER_PCA9450
-
-#define CONFIG_SYS_I2C
 #endif /* CONFIG_SPL_BUILD */
 
-/* ENET Config */
-/* ENET1 */
-#if defined(CONFIG_CMD_NET)
-#define CONFIG_ETHPRIME                        "eth0" /* eqos is aliased on-module Ethernet interface */
-
-#define CONFIG_FEC_XCV_TYPE            RGMII
-#define CONFIG_FEC_MXC_PHYADDR         7
-#define FEC_QUIRK_ENET_MAC
-
-#define PHY_ANEG_TIMEOUT 20000
-#endif /* CONFIG_CMD_NET */
-
 #define MEM_LAYOUT_ENV_SETTINGS \
-       "fdt_addr_r=0x43000000\0" \
-       "kernel_addr_r=0x40000000\0" \
-       "ramdisk_addr_r=0x46400000\0" \
-       "scriptaddr=0x46000000\0"
+       "fdt_addr_r=0x50200000\0" \
+       "kernel_addr_r=" __stringify(CONFIG_SYS_LOAD_ADDR) "\0" \
+       "kernel_comp_addr_r=0x40200000\0" \
+       "kernel_comp_size=0x08000000\0" \
+       "ramdisk_addr_r=0x50300000\0" \
+       "scriptaddr=0x50280000\0"
 
 /* Enable Distro Boot */
-#ifndef CONFIG_SPL_BUILD
 #define BOOT_TARGET_DEVICES(func) \
        func(MMC, mmc, 1) \
        func(MMC, mmc, 2) \
        func(DHCP, dhcp, na)
 #include <config_distro_bootcmd.h>
-#undef CONFIG_ISO_PARTITION
-#else
-#define BOOTENV
-#endif
 
 #if defined(CONFIG_TDX_EASY_INSTALLER)
 #  define BOOT_SCRIPT  "boot-tezi.scr"
@@ -69,7 +43,7 @@
 #endif
 
 /* Initial environment variables */
-#define CONFIG_EXTRA_ENV_SETTINGS \
+#define CFG_EXTRA_ENV_SETTINGS \
        BOOTENV \
        MEM_LAYOUT_ENV_SETTINGS \
        "bootcmd_mfg=fastboot 0\0" \
        "fdt_board=dev\0" \
        "initrd_addr=0x43800000\0" \
        "initrd_high=0xffffffffffffffff\0" \
-       "netargs=setenv bootargs console=${console},${baudrate} " \
-               "root=/dev/nfs ip=dhcp nfsroot=${serverip}:${nfsroot},v3,tcp" \
-               "\0" \
-       "nfsboot=run netargs; dhcp ${loadaddr} ${boot_file}; " \
-               "tftp ${fdt_addr} verdin/${fdtfile}; " \
-               "booti ${loadaddr} - ${fdt_addr}\0" \
-       "setup=setenv setupargs console=${console},${baudrate} console=tty1 " \
+       "setup=setenv setupargs console=tty1 console=${console},${baudrate} " \
                "consoleblank=0 earlycon\0" \
        "update_uboot=askenv confirm Did you load flash.bin (y/N)?; " \
                "if test \"$confirm\" = \"y\"; then " \
                "${blkcnt} / 0x200; mmc dev 2 1; mmc write ${loadaddr} 0x0 " \
                "${blkcnt}; fi\0"
 
-#define CONFIG_SYS_INIT_RAM_ADDR       0x40000000
-#define CONFIG_SYS_INIT_RAM_SIZE       SZ_512K
-#define CONFIG_SYS_INIT_SP_OFFSET \
-       (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
-#define CONFIG_SYS_INIT_SP_ADDR \
-       (CONFIG_SYS_INIT_RAM_ADDR + CONFIG_SYS_INIT_SP_OFFSET)
-
-#define CONFIG_SYS_BOOTM_LEN           SZ_64M /* Increase max gunzip size */
+#define CFG_SYS_INIT_RAM_ADDR  0x40000000
+#define CFG_SYS_INIT_RAM_SIZE  SZ_512K
 
 /* i.MX 8M Plus supports max. 8GB memory in two albeit concecutive banks */
-#define CONFIG_SYS_SDRAM_BASE          0x40000000
+#define CFG_SYS_SDRAM_BASE             0x40000000
 #define PHYS_SDRAM                     0x40000000
 #define PHYS_SDRAM_SIZE                        (SZ_2G + SZ_1G)
 #define PHYS_SDRAM_2                   0x100000000
 #define PHYS_SDRAM_2_SIZE              (SZ_4G + SZ_1G)
 
-/* UART */
-#define CONFIG_MXC_UART_BASE           UART3_BASE_ADDR
-
-/* Monitor Command Prompt */
-#define CONFIG_SYS_CBSIZE              SZ_2K
-#define CONFIG_SYS_MAXARGS             64
-#define CONFIG_SYS_BARGSIZE            CONFIG_SYS_CBSIZE
-#define CONFIG_SYS_PBSIZE              (CONFIG_SYS_CBSIZE + \
-                                       sizeof(CONFIG_SYS_PROMPT) + 16)
-
-/* USDHC */
-#define CONFIG_SYS_FSL_USDHC_NUM       2
-#define CONFIG_SYS_FSL_ESDHC_ADDR      0
-
 #endif /* __VERDIN_IMX8MP_H */