+++ /dev/null
-/*
- * (C) Copyright 2003-2006 Wolfgang Denk, DENX Software Engineering,
- * wd@denx.de.
- *
- * SPDX-License-Identifier: GPL-2.0+
- */
-
-#ifndef __CONFIG_H
-#define __CONFIG_H
-
-/*
- * High Level Configuration Options
- * (easy to change)
- */
-#define CONFIG_MPC5200 1 /* This is an MPC5200 CPU */
-#define CONFIG_V38B 1 /* ...on V38B board */
-
-#define CONFIG_SYS_TEXT_BASE 0xFF000000
-
-#define CONFIG_SYS_MPC5XXX_CLKIN 33000000 /* ...running at 33.000000MHz */
-
-#define CONFIG_RTC_PCF8563 1 /* has PCF8563 RTC */
-#define CONFIG_MPC5200_DDR 1 /* has DDR SDRAM */
-
-#undef CONFIG_HW_WATCHDOG /* don't use watchdog */
-
-#define CONFIG_NETCONSOLE 1
-
-#define CONFIG_BOARD_EARLY_INIT_R 1 /* do board-specific init */
-#define CONFIG_BOARD_EARLY_INIT_F 1 /* do board-specific init */
-#define CONFIG_MISC_INIT_R
-
-#define CONFIG_SYS_XLB_PIPELINING 1 /* gives better performance */
-
-#define CONFIG_HIGH_BATS 1 /* High BATs supported */
-
-/*
- * Serial console configuration
- */
-#define CONFIG_PSC_CONSOLE 1 /* console is on PSC1 */
-#define CONFIG_BAUDRATE 115200 /* ... at 115200 bps */
-#define CONFIG_SYS_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200, 230400 }
-
-/*
- * DDR
- */
-#define SDRAM_DDR 1 /* is DDR */
-/* Settings for XLB = 132 MHz */
-#define SDRAM_MODE 0x018D0000
-#define SDRAM_EMODE 0x40090000
-#define SDRAM_CONTROL 0x704f0f00
-#define SDRAM_CONFIG1 0x73722930
-#define SDRAM_CONFIG2 0x47770000
-#define SDRAM_TAPDELAY 0x10000000
-
-/*
- * PCI - no suport
- */
-#undef CONFIG_PCI
-
-/*
- * Partitions
- */
-#define CONFIG_MAC_PARTITION 1
-#define CONFIG_DOS_PARTITION 1
-
-/*
- * USB
- */
-#define CONFIG_USB_OHCI
-#define CONFIG_USB_STORAGE
-#define CONFIG_USB_CLOCK 0x0001BBBB
-#define CONFIG_USB_CONFIG 0x00001000
-
-
-/*
- * BOOTP options
- */
-#define CONFIG_BOOTP_BOOTFILESIZE
-#define CONFIG_BOOTP_BOOTPATH
-#define CONFIG_BOOTP_GATEWAY
-#define CONFIG_BOOTP_HOSTNAME
-
-
-/*
- * Command line configuration.
- */
-#define CONFIG_CMD_FAT
-#define CONFIG_CMD_I2C
-#define CONFIG_CMD_IDE
-#define CONFIG_CMD_PING
-#define CONFIG_CMD_DHCP
-#define CONFIG_CMD_DIAG
-#define CONFIG_CMD_IRQ
-#define CONFIG_CMD_JFFS2
-#define CONFIG_CMD_MII
-#define CONFIG_CMD_SDRAM
-#define CONFIG_CMD_DATE
-#define CONFIG_CMD_USB
-#define CONFIG_CMD_FAT
-
-
-#define CONFIG_TIMESTAMP /* Print image info with timestamp */
-
-/*
- * Boot low with 16 MB Flash
- */
-#define CONFIG_SYS_LOWBOOT 1
-#define CONFIG_SYS_LOWBOOT16 1
-
-/*
- * Autobooting
- */
-#define CONFIG_BOOTDELAY 3 /* autoboot after 3 seconds */
-
-#define CONFIG_PREBOOT "echo;" \
- "echo Type \\\"run flash_nfs\\\" to mount root filesystem over NFS;" \
- "echo"
-
-#undef CONFIG_BOOTARGS
-
-#define CONFIG_EXTRA_ENV_SETTINGS \
- "bootcmd=run net_nfs\0" \
- "bootdelay=3\0" \
- "baudrate=115200\0" \
- "preboot=echo;echo Type \"run flash_nfs\" to mount root " \
- "filesystem over NFS; echo\0" \
- "netdev=eth0\0" \
- "ramargs=setenv bootargs root=/dev/ram rw wdt=off \0" \
- "addip=setenv bootargs $(bootargs) " \
- "ip=$(ipaddr):$(serverip):$(gatewayip):" \
- "$(netmask):$(hostname):$(netdev):off panic=1\0" \
- "flash_nfs=run nfsargs addip;bootm $(kernel_addr)\0" \
- "flash_self=run ramargs addip;bootm $(kernel_addr) " \
- "$(ramdisk_addr)\0" \
- "net_nfs=tftp 200000 $(bootfile);run nfsargs addip;bootm\0" \
- "nfsargs=setenv bootargs root=/dev/nfs rw " \
- "nfsroot=$(serverip):$(rootpath) wdt=off\0" \
- "hostname=v38b\0" \
- "ethact=FEC\0" \
- "rootpath=/opt/eldk-3.1.1/ppc_6xx\0" \
- "update=prot off ff000000 ff03ffff; era ff000000 ff03ffff; " \
- "cp.b 200000 ff000000 $(filesize);" \
- "prot on ff000000 ff03ffff\0" \
- "load=tftp 200000 $(u-boot)\0" \
- "netmask=255.255.0.0\0" \
- "ipaddr=192.168.160.18\0" \
- "serverip=192.168.1.1\0" \
- "bootfile=/tftpboot/v38b/uImage\0" \
- "u-boot=/tftpboot/v38b/u-boot.bin\0" \
- ""
-
-#define CONFIG_BOOTCOMMAND "run net_nfs"
-
-/*
- * IPB Bus clocking configuration.
- */
-#undef CONFIG_SYS_IPBCLK_EQUALS_XLBCLK /* define for 133MHz speed */
-
-/*
- * I2C configuration
- */
-#define CONFIG_HARD_I2C 1 /* I2C with hardware support */
-#define CONFIG_SYS_I2C_MODULE 2 /* Select I2C module #1 or #2 */
-#define CONFIG_SYS_I2C_SPEED 100000 /* 100 kHz */
-#define CONFIG_SYS_I2C_SLAVE 0x7F
-
-/*
- * EEPROM configuration
- */
-#define CONFIG_SYS_I2C_EEPROM_ADDR 0x50 /* 1010000x */
-#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1
-#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 3
-#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 70
-
-/*
- * RTC configuration
- */
-#define CONFIG_SYS_I2C_RTC_ADDR 0x51
-
-/*
- * Flash configuration - use CFI driver
- */
-#define CONFIG_SYS_FLASH_CFI 1 /* Flash is CFI conformant */
-#define CONFIG_FLASH_CFI_DRIVER 1 /* Use the common driver */
-#define CONFIG_SYS_FLASH_CFI_AMD_RESET 1
-#define CONFIG_SYS_FLASH_BASE 0xFF000000
-#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* max num of flash banks */
-#define CONFIG_SYS_FLASH_BANKS_LIST { CONFIG_SYS_FLASH_BASE }
-#define CONFIG_SYS_FLASH_SIZE 0x01000000 /* 16 MiB */
-#define CONFIG_SYS_MAX_FLASH_SECT 256 /* max num of sects on one chip */
-#define CONFIG_SYS_FLASH_USE_BUFFER_WRITE 1 /* flash write speed-up */
-
-/*
- * Environment settings
- */
-#define CONFIG_ENV_IS_IN_FLASH 1
-#define CONFIG_ENV_ADDR (CONFIG_SYS_FLASH_BASE + 0x00040000)
-#define CONFIG_ENV_SIZE 0x10000
-#define CONFIG_ENV_SECT_SIZE 0x10000
-#define CONFIG_ENV_OVERWRITE 1
-
-/*
- * Memory map
- */
-#define CONFIG_SYS_MBAR 0xF0000000
-#define CONFIG_SYS_SDRAM_BASE 0x00000000
-#define CONFIG_SYS_DEFAULT_MBAR 0x80000000
-
-/* Use SRAM until RAM will be available */
-#define CONFIG_SYS_INIT_RAM_ADDR MPC5XXX_SRAM
-#define CONFIG_SYS_INIT_RAM_SIZE MPC5XXX_SRAM_SIZE /* Size of used area in DPRAM */
-
-#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
-#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET
-
-#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE
-#if (CONFIG_SYS_MONITOR_BASE < CONFIG_SYS_FLASH_BASE)
-# define CONFIG_SYS_RAMBOOT 1
-#endif
-
-#define CONFIG_SYS_MONITOR_LEN (256 << 10) /* Reserve 256kB for Monitor */
-#define CONFIG_SYS_MALLOC_LEN (128 << 10) /* Reserve 128kB for malloc() */
-#define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Linux initial memory map */
-
-/*
- * Ethernet configuration
- */
-#define CONFIG_MPC5xxx_FEC 1
-#define CONFIG_MPC5xxx_FEC_MII100
-#define CONFIG_PHY_ADDR 0x00
-#define CONFIG_MII 1
-
-/*
- * GPIO configuration
- */
-#define CONFIG_SYS_GPS_PORT_CONFIG 0x90001404
-
-/*
- * Miscellaneous configurable options
- */
-#define CONFIG_SYS_LONGHELP /* undef to save memory */
-#if defined(CONFIG_CMD_KGDB)
-#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */
-#else
-#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */
-#endif
-#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */
-#define CONFIG_SYS_MAXARGS 16 /* max number of command args */
-#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */
-
-#define CONFIG_SYS_MEMTEST_START 0x00100000 /* memtest works on */
-#define CONFIG_SYS_MEMTEST_END 0x00f00000 /* 1 ... 15 MB in DRAM */
-
-#define CONFIG_SYS_LOAD_ADDR 0x100000 /* default load address */
-
-#define CONFIG_SYS_CACHELINE_SIZE 32 /* For MPC5xxx CPUs */
-#if defined(CONFIG_CMD_KGDB)
-# define CONFIG_SYS_CACHELINE_SHIFT 5 /* log base 2 of the above value */
-#endif
-
-/*
- * Various low-level settings
- */
-#define CONFIG_SYS_HID0_INIT HID0_ICE | HID0_ICFI
-#define CONFIG_SYS_HID0_FINAL HID0_ICE
-
-#define CONFIG_SYS_BOOTCS_START CONFIG_SYS_FLASH_BASE
-#define CONFIG_SYS_BOOTCS_SIZE CONFIG_SYS_FLASH_SIZE
-#define CONFIG_SYS_BOOTCS_CFG 0x00047801
-#define CONFIG_SYS_CS0_START CONFIG_SYS_FLASH_BASE
-#define CONFIG_SYS_CS0_SIZE CONFIG_SYS_FLASH_SIZE
-
-#define CONFIG_SYS_CS_BURST 0x00000000
-#define CONFIG_SYS_CS_DEADCYCLE 0x33333333
-
-#define CONFIG_SYS_RESET_ADDRESS 0xff000000
-
-/*
- * IDE/ATA (supports IDE harddisk)
- */
-#undef CONFIG_IDE_8xx_PCCARD /* Don't use IDE with PC Card Adapter */
-#undef CONFIG_IDE_8xx_DIRECT /* Direct IDE not supported */
-#undef CONFIG_IDE_LED /* LED for ide not supported */
-
-#define CONFIG_IDE_RESET /* reset for ide supported */
-#define CONFIG_IDE_PREINIT
-
-#define CONFIG_SYS_IDE_MAXBUS 1 /* max. 1 IDE bus */
-#define CONFIG_SYS_IDE_MAXDEVICE 1 /* max. 1 drive per IDE bus */
-
-#define CONFIG_SYS_ATA_IDE0_OFFSET 0x0000
-
-#define CONFIG_SYS_ATA_BASE_ADDR MPC5XXX_ATA
-
-#define CONFIG_SYS_ATA_DATA_OFFSET (0x0060) /* data I/O offset */
-
-#define CONFIG_SYS_ATA_REG_OFFSET (CONFIG_SYS_ATA_DATA_OFFSET) /* normal register accesses offset */
-
-#define CONFIG_SYS_ATA_ALT_OFFSET (0x005C) /* alternate registers offset */
-
-#define CONFIG_SYS_ATA_STRIDE 4 /* Interval between registers */
-
-/*
- * Status LED
- */
-#define CONFIG_STATUS_LED /* Status LED enabled */
-#define CONFIG_BOARD_SPECIFIC_LED /* version has board specific leds */
-
-#define CONFIG_SYS_LED_BASE MPC5XXX_GPT7_ENABLE /* Timer 7 GPIO */
-#ifndef __ASSEMBLY__
-typedef unsigned int led_id_t;
-
-#define __led_toggle(_msk) \
- do { \
- *((volatile long *) (CONFIG_SYS_LED_BASE)) ^= (_msk); \
- } while(0)
-
-#define __led_set(_msk, _st) \
- do { \
- if ((_st)) \
- *((volatile long *) (CONFIG_SYS_LED_BASE)) &= ~(_msk); \
- else \
- *((volatile long *) (CONFIG_SYS_LED_BASE)) |= (_msk); \
- } while(0)
-
-#define __led_init(_msk, st) \
- do { \
- *((volatile long *) (CONFIG_SYS_LED_BASE)) |= 0x34; \
- } while(0)
-#endif /* __ASSEMBLY__ */
-
-#endif /* __CONFIG_H */
projects / platform / kernel / u-boot.git / blobdiff