#define __CONFIG_TI_OMAP5_COMMON_H
/* Use General purpose timer 1 */
-#define CONFIG_SYS_TIMERBASE GPT2_BASE
+#define CFG_SYS_TIMERBASE GPT2_BASE
-/*
- * For the DDR timing information we can either dynamically determine
- * the timings to use or use pre-determined timings (based on using the
- * dynamic method. Default to the static timing infomation.
- */
-#define CONFIG_SYS_EMIF_PRECALCULATED_TIMING_REGS
-#ifndef CONFIG_SYS_EMIF_PRECALCULATED_TIMING_REGS
-#define CONFIG_SYS_AUTOMATIC_SDRAM_DETECTION
-#define CONFIG_SYS_DEFAULT_LPDDR2_TIMINGS
-#endif
-
-#define CONFIG_PALMAS_POWER
+#include <linux/stringify.h>
#include <asm/arch/cpu.h>
#include <asm/arch/omap.h>
/*
* Hardware drivers
*/
-#define CONFIG_SYS_NS16550_CLK 48000000
-#if !defined(CONFIG_DM_SERIAL)
-#define CONFIG_SYS_NS16550_SERIAL
-#define CONFIG_SYS_NS16550_REG_SIZE (-4)
-#endif
+#define CFG_SYS_NS16550_CLK 48000000
/*
* Environment setup
#define DFUARGS
#endif
-#include <environment/ti/boot.h>
-#include <environment/ti/mmc.h>
-#include <environment/ti/nand.h>
+#include <env/ti/mmc.h>
+#include <env/ti/nand.h>
+
+#ifndef CONSOLEDEV
+#define CONSOLEDEV "ttyS2"
+#endif
+
+#ifndef PARTS_DEFAULT
+/*
+ * Default GPT tables for eMMC (Linux and Android). Notes:
+ * 1. Keep partitions aligned to erase group size (512 KiB) when possible
+ * 2. Keep partitions in sync with DFU_ALT_INFO_EMMC (see dfu.h)
+ * 3. Keep 'bootloader' partition (U-Boot proper) start address in sync with
+ * CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR (see common/spl/Kconfig)
+ */
+#define PARTS_DEFAULT \
+ /* Linux partitions */ \
+ "uuid_disk=${uuid_gpt_disk};" \
+ "name=bootloader,start=384K,size=1792K,uuid=${uuid_gpt_bootloader};" \
+ "name=rootfs,start=2688K,size=-,uuid=${uuid_gpt_rootfs}\0" \
+ /* Android partitions */ \
+ "partitions_android=" \
+ "uuid_disk=${uuid_gpt_disk};" \
+ "name=xloader,start=128K,size=256K,uuid=${uuid_gpt_xloader};" \
+ "name=bootloader,size=2048K,uuid=${uuid_gpt_bootloader};" \
+ "name=uboot-env,start=2432K,size=256K,uuid=${uuid_gpt_reserved};" \
+ "name=misc,size=128K,uuid=${uuid_gpt_misc};" \
+ "name=boot_a,size=20M,uuid=${uuid_gpt_boot_a};" \
+ "name=boot_b,size=20M,uuid=${uuid_gpt_boot_b};" \
+ "name=dtbo_a,size=8M,uuid=${uuid_gpt_dtbo_a};" \
+ "name=dtbo_b,size=8M,uuid=${uuid_gpt_dtbo_b};" \
+ "name=vbmeta_a,size=64K,uuid=${uuid_gpt_vbmeta_a};" \
+ "name=vbmeta_b,size=64K,uuid=${uuid_gpt_vbmeta_b};" \
+ "name=recovery,size=64M,uuid=${uuid_gpt_recovery};" \
+ "name=super,size=2560M,uuid=${uuid_gpt_super};" \
+ "name=metadata,size=16M,uuid=${uuid_gpt_metadata};" \
+ "name=userdata,size=-,uuid=${uuid_gpt_userdata}"
+#endif /* PARTS_DEFAULT */
+
+#if defined(CONFIG_CMD_AVB)
+#define AVB_VERIFY_CHECK "if run avb_verify; then " \
+ "echo AVB verification OK.;" \
+ "set bootargs $bootargs $avb_bootargs;" \
+ "else " \
+ "echo AVB verification failed.;" \
+ "exit; fi;"
+#define AVB_VERIFY_CMD "avb_verify=avb init 1; avb verify $slot_suffix;\0"
+#else
+#define AVB_VERIFY_CHECK ""
+#define AVB_VERIFY_CMD ""
+#endif
+
+#define CONTROL_PARTITION "misc"
-#define CONFIG_EXTRA_ENV_SETTINGS \
+#if defined(CONFIG_CMD_AB_SELECT)
+#define AB_SELECT_SLOT \
+ "if part number mmc 1 " CONTROL_PARTITION " control_part_number; " \
+ "then " \
+ "echo " CONTROL_PARTITION \
+ " partition number:${control_part_number};" \
+ "ab_select slot_name mmc ${mmcdev}:${control_part_number};" \
+ "else " \
+ "echo " CONTROL_PARTITION " partition not found;" \
+ "exit;" \
+ "fi;" \
+ "setenv slot_suffix _${slot_name};"
+#define AB_SELECT_ARGS \
+ "setenv bootargs_ab androidboot.slot_suffix=${slot_suffix}; " \
+ "echo A/B cmdline addition: ${bootargs_ab};" \
+ "setenv bootargs ${bootargs} ${bootargs_ab};"
+#else
+#define AB_SELECT_SLOT ""
+#define AB_SELECT_ARGS ""
+#endif
+
+/*
+ * Prepares complete device tree blob for current board (for Android boot).
+ *
+ * Boot image or recovery image should be loaded into $loadaddr prior to running
+ * these commands. The logic of these commnads is next:
+ *
+ * 1. Read correct DTB for current SoC/board from boot image in $loadaddr
+ * to $fdtaddr
+ * 2. Merge all needed DTBO for current board from 'dtbo' partition into read
+ * DTB
+ * 3. User should provide $fdtaddr as 3rd argument to 'bootm'
+ */
+#define PREPARE_FDT \
+ "echo Preparing FDT...; " \
+ "if test $board_name = am57xx_evm_reva3; then " \
+ "echo \" Reading DTBO partition...\"; " \
+ "part start mmc ${mmcdev} dtbo${slot_suffix} p_dtbo_start; " \
+ "part size mmc ${mmcdev} dtbo${slot_suffix} p_dtbo_size; " \
+ "mmc read ${dtboaddr} ${p_dtbo_start} ${p_dtbo_size}; " \
+ "echo \" Reading DTB for AM57x EVM RevA3...\"; " \
+ "abootimg get dtb --index=0 dtb_start dtb_size; " \
+ "cp.b $dtb_start $fdtaddr $dtb_size; " \
+ "fdt addr $fdtaddr 0x80000; " \
+ "echo \" Applying DTBOs for AM57x EVM RevA3...\"; " \
+ "adtimg addr $dtboaddr; " \
+ "adtimg get dt --index=0 dtbo0_addr dtbo0_size; " \
+ "fdt apply $dtbo0_addr; " \
+ "adtimg get dt --index=1 dtbo1_addr dtbo1_size; " \
+ "fdt apply $dtbo1_addr; " \
+ "elif test $board_name = beagle_x15_revc; then " \
+ "echo \" Reading DTB for Beagle X15 RevC...\"; " \
+ "abootimg get dtb --index=0 dtb_start dtb_size; " \
+ "cp.b $dtb_start $fdtaddr $dtb_size; " \
+ "fdt addr $fdtaddr 0x80000; " \
+ "else " \
+ "echo Error: Android boot is not supported for $board_name; " \
+ "exit; " \
+ "fi; " \
+
+#define DEFAULT_COMMON_BOOT_TI_ARGS \
+ "console=" CONSOLEDEV ",115200n8\0" \
+ "fdtfile=undefined\0" \
+ "finduuid=part uuid mmc 0:2 uuid\0" \
+ "usbtty=cdc_acm\0" \
+ "vram=16M\0" \
+ AVB_VERIFY_CMD \
+ "partitions=" PARTS_DEFAULT "\0" \
+ "optargs=\0" \
+ "dofastboot=0\0" \
+ "emmc_android_boot=" \
+ "setenv mmcdev 1; " \
+ "mmc dev $mmcdev; " \
+ "mmc rescan; " \
+ AB_SELECT_SLOT \
+ "if bcb load " __stringify(CONFIG_FASTBOOT_FLASH_MMC_DEV) " " \
+ CONTROL_PARTITION "; then " \
+ "setenv ardaddr -; " \
+ "if bcb test command = bootonce-bootloader; then " \
+ "echo Android: Bootloader boot...; " \
+ "bcb clear command; bcb store; " \
+ "fastboot 1; " \
+ "exit; " \
+ "elif bcb test command = boot-recovery; then " \
+ "echo Android: Recovery boot...; " \
+ "setenv ardaddr $loadaddr;" \
+ "setenv apart recovery; " \
+ "else " \
+ "echo Android: Normal boot...; " \
+ "setenv ardaddr $loadaddr; " \
+ "setenv apart boot${slot_suffix}; " \
+ "fi; " \
+ "else " \
+ "echo Warning: BCB is corrupted or does not exist; " \
+ "echo Android: Normal boot...; " \
+ "fi; " \
+ "setenv eval_bootargs setenv bootargs $bootargs; " \
+ "run eval_bootargs; " \
+ "setenv machid fe6; " \
+ AVB_VERIFY_CHECK \
+ AB_SELECT_ARGS \
+ "if part start mmc $mmcdev $apart boot_start; then " \
+ "part size mmc $mmcdev $apart boot_size; " \
+ "mmc read $loadaddr $boot_start $boot_size; " \
+ PREPARE_FDT \
+ "bootm $loadaddr $ardaddr $fdtaddr; " \
+ "else " \
+ "echo $apart partition not found; " \
+ "exit; " \
+ "fi;\0"
+
+#define DEFAULT_FDT_TI_ARGS \
+ "findfdt="\
+ "if test $board_name = omap5_uevm; then " \
+ "setenv fdtfile omap5-uevm.dtb; fi; " \
+ "if test $board_name = dra7xx; then " \
+ "setenv fdtfile dra7-evm.dtb; fi;" \
+ "if test $board_name = dra72x-revc; then " \
+ "setenv fdtfile dra72-evm-revc.dtb; fi;" \
+ "if test $board_name = dra72x; then " \
+ "setenv fdtfile dra72-evm.dtb; fi;" \
+ "if test $board_name = dra71x; then " \
+ "setenv fdtfile dra71-evm.dtb; fi;" \
+ "if test $board_name = dra76x_acd; then " \
+ "setenv fdtfile dra76-evm.dtb; fi;" \
+ "if test $board_name = beagle_x15; then " \
+ "setenv fdtfile am57xx-beagle-x15.dtb; fi;" \
+ "if test $board_name = beagle_x15_revb1; then " \
+ "setenv fdtfile am57xx-beagle-x15-revb1.dtb; fi;" \
+ "if test $board_name = beagle_x15_revc; then " \
+ "setenv fdtfile am57xx-beagle-x15-revc.dtb; fi;" \
+ "if test $board_name = am5729_beagleboneai; then " \
+ "setenv fdtfile am5729-beagleboneai.dtb; fi;" \
+ "if test $board_name = am572x_idk; then " \
+ "setenv fdtfile am572x-idk.dtb; fi;" \
+ "if test $board_name = am574x_idk; then " \
+ "setenv fdtfile am574x-idk.dtb; fi;" \
+ "if test $board_name = am57xx_evm; then " \
+ "setenv fdtfile am57xx-beagle-x15.dtb; fi;" \
+ "if test $board_name = am57xx_evm_reva3; then " \
+ "setenv fdtfile am57xx-beagle-x15.dtb; fi;" \
+ "if test $board_name = am571x_idk; then " \
+ "setenv fdtfile am571x-idk.dtb; fi;" \
+ "if test $fdtfile = undefined; then " \
+ "echo WARNING: Could not determine device tree to use; fi; \0"
+
+#define BOOT_TARGET_DEVICES(func) \
+ func(MMC, mmc, 0) \
+ func(MMC, mmc, 1) \
+ func(PXE, pxe, na) \
+ func(DHCP, dhcp, na)
+
+#include <config_distro_bootcmd.h>
+
+#define CFG_EXTRA_ENV_SETTINGS \
DEFAULT_LINUX_BOOT_ENV \
DEFAULT_MMC_TI_ARGS \
DEFAULT_FIT_TI_ARGS \
DFUARGS \
NETARGS \
NANDARGS \
+ BOOTENV
/*
* SPL related defines. The Public RAM memory map the ROM defines the
* RAM from address 0x40301350 (0x40300000+0x1000(reserved)+0x350(cert)).
*/
#define TI_OMAP5_SECURE_BOOT_RESV_SRAM_SZ 0x1000
-#define CONFIG_SPL_TEXT_BASE CONFIG_ISW_ENTRY_ADDR
/* If no specific start address is specified then the secure EMIF
* region will be placed at the end of the DDR space. In order to prevent
* the main u-boot relocation from clobbering that memory and causing a
* firewall violation, we tell u-boot that memory is protected RAM (PRAM)
*/
#if (CONFIG_TI_SECURE_EMIF_REGION_START == 0)
-#define CONFIG_PRAM (CONFIG_TI_SECURE_EMIF_TOTAL_REGION_SIZE) >> 10
+#define CFG_PRAM (CONFIG_TI_SECURE_EMIF_TOTAL_REGION_SIZE) >> 10
#endif
#else
/*
* For all booting on GP parts, the flash loader image is
* downloaded into internal RAM at address 0x40300000.
*/
-#define CONFIG_SPL_TEXT_BASE 0x40300000
-#endif
-
-#define CONFIG_SYS_SPL_ARGS_ADDR (CONFIG_SYS_SDRAM_BASE + \
- (128 << 20))
-#ifdef CONFIG_SPL_BUILD
-#undef CONFIG_TIMER
#endif
#endif /* __CONFIG_TI_OMAP5_COMMON_H */
projects / platform / kernel / u-boot.git / blobdiff