#ifndef __CONFIG_TI_ARMV7_COMMON_H__
#define __CONFIG_TI_ARMV7_COMMON_H__
-/* Common define for many platforms. */
-#define CONFIG_OMAP
-#define CONFIG_OMAP_COMMON
-#define CONFIG_SYS_GENERIC_BOARD
-
/*
* We typically do not contain NOR flash. In the cases where we do, we
* undefine this later.
#define CONFIG_SYS_NO_FLASH
/* Support both device trees and ATAGs. */
-#define CONFIG_OF_LIBFDT
#define CONFIG_CMDLINE_TAG
#define CONFIG_SETUP_MEMORY_TAGS
#define CONFIG_INITRD_TAG
"fdt_addr_r=0x88000000\0" \
"rdaddr=0x88080000\0" \
"ramdisk_addr_r=0x88080000\0" \
+ "scriptaddr=0x80000000\0" \
+ "pxefile_addr_r=0x80100000\0" \
"bootm_size=0x10000000\0"
-/*
- * Default to a quick boot delay.
- */
-#define CONFIG_BOOTDELAY 1
+#define DEFAULT_MMC_TI_ARGS \
+ "mmcdev=0\0" \
+ "mmcrootfstype=ext4 rootwait\0" \
+ "finduuid=part uuid mmc 0:2 uuid\0" \
+ "args_mmc=run finduuid;setenv bootargs console=${console} " \
+ "${optargs} " \
+ "root=PARTUUID=${uuid} rw " \
+ "rootfstype=${mmcrootfstype}\0" \
+ "loadbootscript=load mmc ${mmcdev} ${loadaddr} boot.scr\0" \
+ "bootscript=echo Running bootscript from mmc${mmcdev} ...; " \
+ "source ${loadaddr}\0" \
+ "bootenvfile=uEnv.txt\0" \
+ "importbootenv=echo Importing environment from mmc${mmcdev} ...; " \
+ "env import -t ${loadaddr} ${filesize}\0" \
+ "loadbootenv=fatload mmc ${mmcdev} ${loadaddr} ${bootenvfile}\0" \
+ "envboot=mmc dev ${mmcdev}; " \
+ "if mmc rescan; then " \
+ "echo SD/MMC found on device ${mmcdev};" \
+ "if run loadbootscript; then " \
+ "run bootscript;" \
+ "else " \
+ "if run loadbootenv; then " \
+ "echo Loaded env from ${bootenvfile};" \
+ "run importbootenv;" \
+ "fi;" \
+ "if test -n $uenvcmd; then " \
+ "echo Running uenvcmd ...;" \
+ "run uenvcmd;" \
+ "fi;" \
+ "fi;" \
+ "fi;\0" \
/*
* DDR information. If the CONFIG_NR_DRAM_BANKS is not defined,
#define CONFIG_NR_DRAM_BANKS 1
#endif
#define CONFIG_SYS_SDRAM_BASE 0x80000000
+
+#ifndef CONFIG_SYS_INIT_SP_ADDR
#define CONFIG_SYS_INIT_SP_ADDR (NON_SECURE_SRAM_END - \
GENERATED_GBL_DATA_SIZE)
+#endif
/* Timer information. */
#define CONFIG_SYS_PTV 2 /* Divisor: 2^(PTV+1) => 8 */
/* I2C IP block */
#define CONFIG_I2C
-#define CONFIG_CMD_I2C
#define CONFIG_SYS_I2C
-#define CONFIG_SYS_OMAP24_I2C_SPEED 100000
-#define CONFIG_SYS_OMAP24_I2C_SLAVE 1
-#define CONFIG_SYS_I2C_OMAP24XX
/* MMC/SD IP block */
#define CONFIG_MMC
#define CONFIG_GENERIC_MMC
-#define CONFIG_OMAP_HSMMC
-#define CONFIG_CMD_MMC
/* McSPI IP block */
#define CONFIG_SPI
-#define CONFIG_OMAP3_SPI
-#define CONFIG_CMD_SPI
/* GPIO block */
-#define CONFIG_OMAP_GPIO
-#define CONFIG_CMD_GPIO
-
-/*
- * GPMC NAND block. We support 1 device and the physical address to
- * access CS0 at is 0x8000000.
- */
-#ifdef CONFIG_NAND
-#define CONFIG_NAND_OMAP_GPMC
-#ifndef CONFIG_SYS_NAND_BASE
-#define CONFIG_SYS_NAND_BASE 0x8000000
-#endif
-#define CONFIG_SYS_MAX_NAND_DEVICE 1
-#define CONFIG_CMD_NAND
-#endif
/*
* The following are general good-enough settings for U-Boot. We set a
* we are on so we do not need to rely on the command prompt. We set a
* console baudrate of 115200 and use the default baud rate table.
*/
-#define CONFIG_SYS_MALLOC_LEN (16 << 20)
-#define CONFIG_SYS_HUSH_PARSER
-#define CONFIG_SYS_PROMPT "U-Boot# "
+#ifdef CONFIG_DFU_MMC
+#define CONFIG_SYS_MALLOC_LEN ((16 << 20) + CONFIG_SYS_DFU_DATA_BUF_SIZE)
+#else
+#define CONFIG_SYS_MALLOC_LEN (16 << 20)
+#endif
#define CONFIG_SYS_CONSOLE_INFO_QUIET
#define CONFIG_BAUDRATE 115200
#define CONFIG_ENV_VARS_UBOOT_CONFIG /* Strongly encouraged */
* mtdparts, both for ease of use in U-Boot and for passing information
* on to the Linux kernel.
*/
-#if defined(CONFIG_SPI_BOOT) || defined(CONFIG_NOR) || defined(CONFIG_NAND)
+#if defined(CONFIG_SPI_BOOT) || defined(CONFIG_NOR) || defined(CONFIG_NAND) || defined(CONFIG_NAND_DAVINCI)
#define CONFIG_MTD_DEVICE /* Required for mtdparts */
#define CONFIG_CMD_MTDPARTS
#endif
-/*
- * For commands to use, we take the default list and add a few other
- * useful commands. Note that we must have set CONFIG_SYS_NO_FLASH
- * prior to this include, in order to skip a few commands. When we do
- * have flash, if we expect these commands they must be enabled in that
- * config. If desired, a specific list of desired commands can be used
- * instead.
- */
-#include <config_cmd_default.h>
-#define CONFIG_CMD_ASKENV
-#define CONFIG_CMD_ECHO
-#define CONFIG_CMD_BOOTZ
#define CONFIG_SUPPORT_RAW_INITRD
/*
*/
#if defined(CONFIG_MMC) || defined(CONFIG_USB_STORAGE)
#define CONFIG_DOS_PARTITION
-#define CONFIG_CMD_FAT
#define CONFIG_FAT_WRITE
-#define CONFIG_CMD_EXT2
-#define CONFIG_CMD_EXT4
-#define CONFIG_CMD_FS_GENERIC
#define CONFIG_PARTITION_UUIDS
#define CONFIG_CMD_PART
#endif
* SPLs). We have our BSS be placed 2MiB after this, to allow for the
* default Linux kernel address of 0x80008000 to work with most sized
* kernels, in the Falcon Mode case. We have the SPL malloc pool at the
- * end of the BSS area. We place our stack at 32MiB after the start of
- * DRAM to allow room for all of the above.
+ * end of the BSS area. We suggest that the stack be placed at 32MiB after
+ * the start of DRAM to allow room for all of the above (handled in Kconfig).
*/
-#define CONFIG_SPL_STACK (CONFIG_SYS_SDRAM_BASE + (32 << 20))
#ifndef CONFIG_SYS_TEXT_BASE
#define CONFIG_SYS_TEXT_BASE 0x80800000
#endif
#define CONFIG_SPL_LIBDISK_SUPPORT
#define CONFIG_SPL_MMC_SUPPORT
#define CONFIG_SPL_FAT_SUPPORT
+#define CONFIG_SPL_EXT_SUPPORT
#endif
+#define CONFIG_SYS_THUMB_BUILD
+
/* General parts of the framework, required. */
#define CONFIG_SPL_I2C_SUPPORT
#define CONFIG_SPL_LIBCOMMON_SUPPORT
#define CONFIG_SPL_LIBGENERIC_SUPPORT
#define CONFIG_SPL_SERIAL_SUPPORT
+#define CONFIG_SPL_POWER_SUPPORT
#define CONFIG_SPL_GPIO_SUPPORT
#define CONFIG_SPL_BOARD_INIT
#endif
#endif /* !CONFIG_NOR_BOOT */
+/* Generic Environment Variables */
+
+#ifdef CONFIG_CMD_NET
+#define NETARGS \
+ "static_ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}:${hostname}" \
+ "::off\0" \
+ "nfsopts=nolock\0" \
+ "rootpath=/export/rootfs\0" \
+ "netloadimage=tftp ${loadaddr} ${bootfile}\0" \
+ "netloadfdt=tftp ${fdtaddr} ${fdtfile}\0" \
+ "netargs=setenv bootargs console=${console} " \
+ "${optargs} " \
+ "root=/dev/nfs " \
+ "nfsroot=${serverip}:${rootpath},${nfsopts} rw " \
+ "ip=dhcp\0" \
+ "netboot=echo Booting from network ...; " \
+ "setenv autoload no; " \
+ "dhcp; " \
+ "run netloadimage; " \
+ "run netloadfdt; " \
+ "run netargs; " \
+ "bootz ${loadaddr} - ${fdtaddr}\0"
+#else
+#define NETARGS ""
+#endif
+
+#include <config_distro_defaults.h>
+
#endif /* __CONFIG_TI_ARMV7_COMMON_H__ */
projects / platform / kernel / u-boot.git / blobdiff