configs: migrate CONFIG_BMP_16/24/32BPP to defconfigs

[platform/kernel/u-boot.git] / include / configs / stm32mp1.h

diff --git a/include/configs/stm32mp1.h b/include/configs/stm32mp1.h
index 4b17bf5..1aa7514 100644 (file)
--- a/include/configs/stm32mp1.h
+++ b/include/configs/stm32mp1.h
@@ -10,14 +10,8 @@
 #include <linux/sizes.h>
 #include <asm/arch/stm32.h>
 
-/*
- * Number of clock ticks in 1 sec
- */
-#define CONFIG_SYS_HZ                          1000
-
-#ifndef CONFIG_STM32MP1_TRUSTED
+#ifndef CONFIG_TFABOOT
 /* PSCI support */
-#define CONFIG_ARMV7_PSCI_1_0
 #define CONFIG_ARMV7_SECURE_BASE               STM32_SYSRAM_BASE
 #define CONFIG_ARMV7_SECURE_MAX_SIZE           STM32_SYSRAM_SIZE
 #endif
@@ -34,21 +28,27 @@
 #define CONFIG_SYS_CBSIZE                      SZ_1K
 
 /*
- * Needed by "loadb"
+ * default load address used for command tftp,  bootm , loadb, ...
  */
-#define CONFIG_SYS_LOAD_ADDR                   STM32_DDR_BASE
+#define CONFIG_LOADADDR                        0xc2000000
+#define CONFIG_SYS_LOAD_ADDR           CONFIG_LOADADDR
 
 /* ATAGs */
 #define CONFIG_CMDLINE_TAG
 #define CONFIG_SETUP_MEMORY_TAGS
 #define CONFIG_INITRD_TAG
 
+/*
+ * For booting Linux, use the first 256 MB of memory, since this is
+ * the maximum mapped by the Linux kernel during initialization.
+ */
+#define CONFIG_SYS_BOOTMAPSZ           SZ_256M
+
 /* Extend size of kernel image for uncompression */
-#define CONFIG_SYS_BOOTM_LEN                   SZ_32M
+#define CONFIG_SYS_BOOTM_LEN           SZ_32M
 
 /* SPL support */
 #ifdef CONFIG_SPL
-/* BOOTROM load address */
 /* SPL use DDR */
 #define CONFIG_SPL_BSS_START_ADDR      0xC0200000
 #define CONFIG_SPL_BSS_MAX_SIZE                0x00100000
@@ -60,14 +60,13 @@
 #define CONFIG_SPL_STACK               (STM32_SYSRAM_BASE + \
                                         STM32_SYSRAM_SIZE)
 #endif /* #ifdef CONFIG_SPL */
-
-#define CONFIG_SYS_MEMTEST_START       STM32_DDR_BASE
-#define CONFIG_SYS_MEMTEST_END         (CONFIG_SYS_MEMTEST_START + SZ_64M)
-#define CONFIG_SYS_MEMTEST_SCRATCH     (CONFIG_SYS_MEMTEST_END + 4)
-
 /*MMC SD*/
 #define CONFIG_SYS_MMC_MAX_DEVICE      3
 
+/* NAND support */
+#define CONFIG_SYS_NAND_ONFI_DETECTION
+#define CONFIG_SYS_MAX_NAND_DEVICE     1
+
 /* Ethernet need */
 #ifdef CONFIG_DWC_ETH_QOS
 #define CONFIG_SYS_NONCACHED_MEMORY    (1 * SZ_1M)     /* 1M */
@@ -82,21 +81,41 @@
 
 #if !defined(CONFIG_SPL_BUILD)
 
-/* NAND support */
-#define CONFIG_SYS_NAND_ONFI_DETECTION
-#define CONFIG_SYS_MAX_NAND_DEVICE     1
-#define BOOT_TARGET_DEVICES(func) \
-       func(MMC, mmc, 1) \
-       func(MMC, mmc, 0) \
-       func(MMC, mmc, 2) \
-       func(PXE, pxe, na)
+#ifdef CONFIG_CMD_MMC
+#define BOOT_TARGET_MMC0(func) func(MMC, mmc, 0)
+#define BOOT_TARGET_MMC1(func) func(MMC, mmc, 1)
+#define BOOT_TARGET_MMC2(func) func(MMC, mmc, 2)
+#else
+#define BOOT_TARGET_MMC0(func)
+#define BOOT_TARGET_MMC1(func)
+#define BOOT_TARGET_MMC2(func)
+#endif
+
+#ifdef CONFIG_NET
+#define BOOT_TARGET_PXE(func)  func(PXE, pxe, na)
+#else
+#define BOOT_TARGET_PXE(func)
+#endif
+
+#ifdef CONFIG_CMD_UBIFS
+#define BOOT_TARGET_UBIFS(func)        func(UBIFS, ubifs, 0)
+#else
+#define BOOT_TARGET_UBIFS(func)
+#endif
+
+#define BOOT_TARGET_DEVICES(func)      \
+       BOOT_TARGET_MMC1(func)          \
+       BOOT_TARGET_UBIFS(func)         \
+       BOOT_TARGET_MMC0(func)          \
+       BOOT_TARGET_MMC2(func)          \
+       BOOT_TARGET_PXE(func)
 
 /*
  * bootcmd for stm32mp1:
  * for serial/usb: execute the stm32prog command
  * for mmc boot (eMMC, SD card), boot only on the same device
- * for nand boot, boot with on ubifs partition on nand
- * for nor boot, use the default order
+ * for nand or spi-nand boot, boot with on ubifs partition on UBI partition
+ * for nor boot, use SD card = mmc0
  */
 #define STM32MP_BOOTCMD "bootcmd_stm32mp=" \
        "echo \"Boot over ${boot_device}${boot_instance}!\";" \
@@ -106,40 +125,32 @@
                "run env_check;" \
                "if test ${boot_device} = mmc;" \
                "then env set boot_targets \"mmc${boot_instance}\"; fi;" \
-               "if test ${boot_device} = nand;" \
+               "if test ${boot_device} = nand ||" \
+                 " test ${boot_device} = spi-nand ;" \
                "then env set boot_targets ubifs0; fi;" \
+               "if test ${boot_device} = nor;" \
+               "then env set boot_targets mmc0; fi;" \
                "run distro_bootcmd;" \
        "fi;\0"
 
 #include <config_distro_bootcmd.h>
 
-#if defined(CONFIG_STM32_QSPI) || defined(CONFIG_NAND_STM32_FMC)
-#define CONFIG_SYS_MTDPARTS_RUNTIME
-#endif
-
-#define STM32MP_MTDPARTS \
-       "mtdparts_nor0=256k(fsbl1),256k(fsbl2),2m(ssbl),256k(u-boot-env),-(nor_user)\0" \
-       "mtdparts_nand0=2m(fsbl),2m(ssbl1),2m(ssbl2),-(UBI)\0"
-
 /*
  * memory layout for 32M uncompressed/compressed kernel,
  * 1M fdt, 1M script, 1M pxe and 1M for splashimage
  * and the ramdisk at the end.
  */
 #define CONFIG_EXTRA_ENV_SETTINGS \
+       "bootdelay=1\0" \
        "kernel_addr_r=0xc2000000\0" \
        "fdt_addr_r=0xc4000000\0" \
        "scriptaddr=0xc4100000\0" \
        "pxefile_addr_r=0xc4200000\0" \
        "splashimage=0xc4300000\0"  \
        "ramdisk_addr_r=0xc4400000\0" \
-       "fdt_high=0xffffffff\0" \
-       "initrd_high=0xffffffff\0" \
-       "env_default=1\0"                               \
-       "env_check=if test $env_default -eq 1;"\
-               " then env set env_default 0;env save;fi\0" \
+       "altbootcmd=run bootcmd\0" \
+       "env_check=if env info -p -d -q; then env save; fi\0" \
        STM32MP_BOOTCMD \
-       STM32MP_MTDPARTS \
        BOOTENV \
        "boot_net_usb_start=true\0"