Convert CONFIG_SYS_LOAD_ADDR to Kconfig

[platform/kernel/u-boot.git] / include / configs / socfpga_sr1500.h

diff --git a/include/configs/socfpga_sr1500.h b/include/configs/socfpga_sr1500.h
index e43b5cf..62c1bc7 100644 (file)
--- a/include/configs/socfpga_sr1500.h
+++ b/include/configs/socfpga_sr1500.h
@@ -1,117 +1,29 @@
+/* SPDX-License-Identifier: GPL-2.0+ */
 /*
  * Copyright (C) 2015 Stefan Roese <sr@denx.de>
- *
- * SPDX-License-Identifier:    GPL-2.0+
  */
 #ifndef __CONFIG_SOCFPGA_SR1500_H__
 #define __CONFIG_SOCFPGA_SR1500_H__
 
 #include <asm/arch/base_addr_ac5.h>
 
-#define CONFIG_BOARD_EARLY_INIT_F
-
-#define CONFIG_SYS_NO_FLASH
-#define CONFIG_DOS_PARTITION
-#define CONFIG_FAT_WRITE
-
-#define CONFIG_HW_WATCHDOG
-
-/* U-Boot Commands */
-#define CONFIG_CMD_ASKENV
-#define CONFIG_CMD_BOOTZ
-#define CONFIG_CMD_CACHE
-#define CONFIG_CMD_DHCP
-#define CONFIG_CMD_EXT4
-#define CONFIG_CMD_EXT4_WRITE
-#define CONFIG_CMD_FAT
-#define CONFIG_CMD_FS_GENERIC
-#define CONFIG_CMD_GPIO
-#define CONFIG_CMD_GREPENV
-#define CONFIG_CMD_MEMTEST
-#define CONFIG_CMD_MII
-#define CONFIG_CMD_MMC
-#define CONFIG_CMD_PING
-#define CONFIG_CMD_SF
-#define CONFIG_CMD_SPI
-#define CONFIG_CMD_TIME
-
 /* Memory configurations */
 #define PHYS_SDRAM_1_SIZE              0x40000000      /* 1GiB on SR1500 */
 
-/* Booting Linux */
-#define CONFIG_BOOTDELAY       3
-#define CONFIG_BOOTFILE                "uImage"
-#define CONFIG_BOOTARGS                "console=ttyS0" __stringify(CONFIG_BAUDRATE)
-#define CONFIG_BOOTCOMMAND     "run mmcload; run mmcboot"
-#define CONFIG_LOADADDR                0x01000000
-#define CONFIG_SYS_LOAD_ADDR   CONFIG_LOADADDR
-#define CONFIG_SYS_CONSOLE_INFO_QUIET  /* don't print console @ startup */
-
 /* Ethernet on SoC (EMAC) */
 #define CONFIG_PHY_INTERFACE_MODE      PHY_INTERFACE_MODE_RGMII
 /* The PHY is autodetected, so no MII PHY address is needed here */
-#define CONFIG_PHY_MARVELL
 #define PHY_ANEG_TIMEOUT       8000
 
-#define CONFIG_EXTRA_ENV_SETTINGS \
-       "verify=n\0" \
-       "loadaddr=" __stringify(CONFIG_SYS_LOAD_ADDR) "\0" \
-       "ramboot=setenv bootargs " CONFIG_BOOTARGS ";" \
-               "bootm ${loadaddr} - ${fdt_addr}\0" \
-       "bootimage=zImage\0" \
-       "fdt_addr=100\0" \
-       "fdtimage=socfpga.dtb\0" \
-               "fsloadcmd=ext2load\0" \
-       "bootm ${loadaddr} - ${fdt_addr}\0" \
-       "mmcroot=/dev/mmcblk0p2\0" \
-       "mmcboot=setenv bootargs " CONFIG_BOOTARGS \
-               " root=${mmcroot} rw rootwait;" \
-               "bootz ${loadaddr} - ${fdt_addr}\0" \
-       "mmcload=mmc rescan;" \
-               "load mmc 0:1 ${loadaddr} ${bootimage};" \
-               "load mmc 0:1 ${fdt_addr} ${fdtimage}\0" \
-       "qspiload=sf probe && mtdparts default && run ubiload\0" \
-       "qspiboot=setenv bootargs " CONFIG_BOOTARGS \
-               " ubi.mtd=1,64 root=ubi0:rootfs rw rootfstype=ubifs;"\
-               "bootz ${loadaddr} - ${fdt_addr}\0" \
-       "ubiload=ubi part UBI && ubifsmount ubi0 && " \
-               "ubifsload ${loadaddr} /boot/${bootimage} && " \
-               "ubifsload ${fdt_addr} /boot/${fdtimage}\0"
-
-/* Environment */
-#define CONFIG_ENV_IS_IN_SPI_FLASH
-
 /* Enable SPI NOR flash reset, needed for SPI booting */
 #define CONFIG_SPI_N25Q256A_RESET
 
 /*
  * Bootcounter
  */
-#define CONFIG_BOOTCOUNT_LIMIT
-/* last 2 lwords in OCRAM */
-#define CONFIG_SYS_BOOTCOUNT_ADDR      0xfffffff8
 #define CONFIG_SYS_BOOTCOUNT_BE
 
 /* Environment setting for SPI flash */
-#define CONFIG_SYS_REDUNDAND_ENVIRONMENT
-#define CONFIG_ENV_SECT_SIZE   (64 * 1024)
-#define CONFIG_ENV_SIZE                (16 * 1024)
-#define CONFIG_ENV_OFFSET      0x000e0000
-#define CONFIG_ENV_OFFSET_REDUND (CONFIG_ENV_OFFSET + CONFIG_ENV_SECT_SIZE)
-#define CONFIG_ENV_SPI_BUS     0
-#define CONFIG_ENV_SPI_CS      0
-#define CONFIG_ENV_SPI_MODE    SPI_MODE_3
-#define CONFIG_ENV_SPI_MAX_HZ  100000000       /* Use max of 100MHz */
-#define CONFIG_SF_DEFAULT_SPEED        100000000
-
-/*
- * The QSPI NOR flash layout on SR1500:
- *
- * 0000.0000 - 0003.ffff: SPL (4 times)
- * 0004.0000 - 000d.ffff: U-Boot
- * 000e.0000 - 000e.ffff: env1
- * 000f.0000 - 000f.ffff: env2
- */
 
 /* The rest of the configuration is shared */
 #include <configs/socfpga_common.h>