#ifndef __CONFIG_SOCFPGA_COMMON_H__
#define __CONFIG_SOCFPGA_COMMON_H__
+#include <linux/stringify.h>
+
/*
* High level configuration
*/
#define CONFIG_CLOCKS
-#define CONFIG_SYS_BOOTMAPSZ (64 * 1024 * 1024)
-
#define CONFIG_TIMESTAMP /* Print image info with timestamp */
/*
*/
#define PHYS_SDRAM_1 0x0
#define CONFIG_SYS_MALLOC_LEN (64 * 1024 * 1024)
-#define CONFIG_SYS_MEMTEST_START PHYS_SDRAM_1
-#define CONFIG_SYS_MEMTEST_END PHYS_SDRAM_1_SIZE
#if defined(CONFIG_TARGET_SOCFPGA_GEN5)
#define CONFIG_SYS_INIT_RAM_ADDR 0xFFFF0000
-#define CONFIG_SYS_INIT_RAM_SIZE 0x10000
+#define CONFIG_SYS_INIT_RAM_SIZE SOCFPGA_PHYS_OCRAM_SIZE
#elif defined(CONFIG_TARGET_SOCFPGA_ARRIA10)
#define CONFIG_SYS_INIT_RAM_ADDR 0xFFE00000
-#define CONFIG_SYS_INIT_RAM_SIZE 0x40000 /* 256KB */
+/* SPL memory allocation configuration, this is for FAT implementation */
+#ifndef CONFIG_SYS_SPL_MALLOC_SIZE
+#define CONFIG_SYS_SPL_MALLOC_SIZE 0x10000
+#endif
+#define CONFIG_SYS_INIT_RAM_SIZE (SOCFPGA_PHYS_OCRAM_SIZE - \
+ CONFIG_SYS_SPL_MALLOC_SIZE)
+#define CONFIG_SYS_SPL_MALLOC_START (CONFIG_SYS_INIT_RAM_ADDR + \
+ CONFIG_SYS_INIT_RAM_SIZE)
#endif
/*
#if ((CONFIG_SYS_BOOTCOUNT_ADDR > CONFIG_SYS_INIT_RAM_ADDR) && \
(CONFIG_SYS_BOOTCOUNT_ADDR < (CONFIG_SYS_INIT_RAM_ADDR + \
CONFIG_SYS_INIT_RAM_SIZE)))
-#define CONFIG_SYS_INIT_SP_ADDR CONFIG_SYS_BOOTCOUNT_ADDR
+#define CONFIG_SPL_STACK CONFIG_SYS_BOOTCOUNT_ADDR
#else
-#define CONFIG_SYS_INIT_SP_ADDR \
+#define CONFIG_SPL_STACK \
(CONFIG_SYS_INIT_RAM_ADDR + CONFIG_SYS_INIT_RAM_SIZE)
#endif
+/*
+ * U-Boot stack setup: if SPL post-reloc uses DDR stack, use it in pre-reloc
+ * phase of U-Boot, too. This prevents overwriting SPL data if stack/heap usage
+ * in U-Boot pre-reloc is higher than in SPL.
+ */
+#if defined(CONFIG_SPL_STACK_R_ADDR) && CONFIG_SPL_STACK_R_ADDR
+#define CONFIG_SYS_INIT_SP_ADDR CONFIG_SPL_STACK_R_ADDR
+#else
+#define CONFIG_SYS_INIT_SP_ADDR CONFIG_SPL_STACK
+#endif
+
#define CONFIG_SYS_SDRAM_BASE PHYS_SDRAM_1
/*
#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE
/* Boot argument buffer size */
-#ifndef CONFIG_SYS_HOSTNAME
-#define CONFIG_SYS_HOSTNAME CONFIG_SYS_BOARD
-#endif
-
/*
* Cache
*/
#define CONFIG_SYS_PL310_BASE SOCFPGA_MPUL2_ADDRESS
/*
- * EPCS/EPCQx1 Serial Flash Controller
- */
-#ifdef CONFIG_ALTERA_SPI
-#define CONFIG_SF_DEFAULT_SPEED 30000000
-/*
- * The base address is configurable in QSys, each board must specify the
- * base address based on it's particular FPGA configuration. Please note
- * that the address here is incremented by 0x400 from the Base address
- * selected in QSys, since the SPI registers are at offset +0x400.
- * #define CONFIG_SYS_SPI_BASE 0xff240400
- */
-#endif
-
-/*
* Ethernet on SoC (EMAC)
*/
#ifdef CONFIG_CMD_NET
* L4 OSC1 Timer 0
*/
#ifndef CONFIG_TIMER
-/* This timer uses eosc1, whose clock frequency is fixed at any condition. */
#define CONFIG_SYS_TIMERBASE SOCFPGA_OSC1TIMER0_ADDRESS
#define CONFIG_SYS_TIMER_COUNTS_DOWN
#define CONFIG_SYS_TIMER_COUNTER (CONFIG_SYS_TIMERBASE + 0x4)
+#ifndef CONFIG_SYS_TIMER_RATE
#define CONFIG_SYS_TIMER_RATE 25000000
#endif
+#endif
/*
* L4 Watchdog
*/
-#ifdef CONFIG_HW_WATCHDOG
-#define CONFIG_DESIGNWARE_WATCHDOG
#define CONFIG_DW_WDT_BASE SOCFPGA_L4WD0_ADDRESS
#define CONFIG_DW_WDT_CLOCK_KHZ 25000
-#define CONFIG_WATCHDOG_TIMEOUT_MSECS 30000
-#endif
/*
* MMC Driver
* NAND Support
*/
#ifdef CONFIG_NAND_DENALI
+#define CONFIG_SYS_NAND_BAD_BLOCK_POS 0
#define CONFIG_SYS_MAX_NAND_DEVICE 1
#define CONFIG_SYS_NAND_ONFI_DETECTION
#define CONFIG_SYS_NAND_REGS_BASE SOCFPGA_NANDREGS_ADDRESS
#endif
/*
- * I2C support
- */
-#ifndef CONFIG_DM_I2C
-#define CONFIG_SYS_I2C
-#define CONFIG_SYS_I2C_BASE SOCFPGA_I2C0_ADDRESS
-#define CONFIG_SYS_I2C_BASE1 SOCFPGA_I2C1_ADDRESS
-#define CONFIG_SYS_I2C_BASE2 SOCFPGA_I2C2_ADDRESS
-#define CONFIG_SYS_I2C_BASE3 SOCFPGA_I2C3_ADDRESS
-/* Using standard mode which the speed up to 100Kb/s */
-#define CONFIG_SYS_I2C_SPEED 100000
-#define CONFIG_SYS_I2C_SPEED1 100000
-#define CONFIG_SYS_I2C_SPEED2 100000
-#define CONFIG_SYS_I2C_SPEED3 100000
-/* Address of device when used as slave */
-#define CONFIG_SYS_I2C_SLAVE 0x02
-#define CONFIG_SYS_I2C_SLAVE1 0x02
-#define CONFIG_SYS_I2C_SLAVE2 0x02
-#define CONFIG_SYS_I2C_SLAVE3 0x02
-#ifndef __ASSEMBLY__
-/* Clock supplied to I2C controller in unit of MHz */
-unsigned int cm_get_l4_sp_clk_hz(void);
-#define IC_CLK (cm_get_l4_sp_clk_hz() / 1000000)
-#endif
-#endif /* CONFIG_DM_I2C */
-
-/*
* QSPI support
*/
-/* Enable multiple SPI NOR flash manufacturers */
-#ifndef CONFIG_SPL_BUILD
-#define CONFIG_SPI_FLASH_MTD
-#endif
/* QSPI reference clock */
#ifndef __ASSEMBLY__
unsigned int cm_get_qspi_controller_clk_hz(void);
#endif
/*
- * Designware SPI support
- */
-
-/*
- * Serial Driver
- */
-#define CONFIG_SYS_NS16550_SERIAL
-
-/*
* USB
*/
/*
* U-Boot environment
*/
-#if !defined(CONFIG_ENV_SIZE)
-#define CONFIG_ENV_SIZE (8 * 1024)
-#endif
/* Environment for SDMMC boot */
-#if defined(CONFIG_ENV_IS_IN_MMC) && !defined(CONFIG_ENV_OFFSET)
-#define CONFIG_SYS_MMC_ENV_DEV 0 /* device 0 */
-#define CONFIG_ENV_OFFSET (34 * 512) /* just after the GPT */
-#endif
/* Environment for QSPI boot */
-#if defined(CONFIG_ENV_IS_IN_SPI_FLASH) && !defined(CONFIG_ENV_OFFSET)
-#define CONFIG_ENV_OFFSET 0x00100000
-#define CONFIG_ENV_SECT_SIZE (64 * 1024)
-#endif
-
-/*
- * mtd partitioning for serial NOR flash
- *
- * device nor0 <ff705000.spi.0>, # parts = 6
- * #: name size offset mask_flags
- * 0: u-boot 0x00100000 0x00000000 0
- * 1: env1 0x00040000 0x00100000 0
- * 2: env2 0x00040000 0x00140000 0
- * 3: UBI 0x03e80000 0x00180000 0
- * 4: boot 0x00e80000 0x00180000 0
- * 5: rootfs 0x01000000 0x01000000 0
- *
- */
/*
* SPL
*
* 0xFFFF_0000 ...... Start of SRAM
* 0xFFFF_xxxx ...... Top of stack (grows down)
- * 0xFFFF_yyyy ...... Malloc area
- * 0xFFFF_zzzz ...... Global Data
- * 0xFFFF_FF00 ...... End of SRAM
+ * 0xFFFF_yyyy ...... Global Data
+ * 0xFFFF_zzzz ...... Malloc area
+ * 0xFFFF_FFFF ...... End of SRAM
*
* SRAM Memory layout for Arria 10:
* 0xFFE0_0000 ...... Start of SRAM (bottom)
* 0xFFEz_zzzz ...... Malloc area (grows up to top)
* 0xFFE3_FFFF ...... End of SRAM (top)
*/
-#define CONFIG_SPL_TEXT_BASE CONFIG_SYS_INIT_RAM_ADDR
+#ifndef CONFIG_SPL_TEXT_BASE
#define CONFIG_SPL_MAX_SIZE CONFIG_SYS_INIT_RAM_SIZE
-
-#if defined(CONFIG_TARGET_SOCFPGA_ARRIA10)
-/* SPL memory allocation configuration, this is for FAT implementation */
-#ifndef CONFIG_SYS_SPL_MALLOC_START
-#define CONFIG_SYS_SPL_MALLOC_SIZE 0x00010000
-#define CONFIG_SYS_SPL_MALLOC_START (CONFIG_SYS_INIT_RAM_SIZE - \
- CONFIG_SYS_SPL_MALLOC_SIZE + \
- CONFIG_SYS_INIT_RAM_ADDR)
-#endif
#endif
/* SPL SDMMC boot support */
#ifdef CONFIG_SPL_MMC_SUPPORT
#if defined(CONFIG_SPL_FS_FAT) || defined(CONFIG_SPL_FS_EXT4)
-#define CONFIG_SPL_FS_LOAD_PAYLOAD_NAME "u-boot-dtb.img"
-#define CONFIG_SYS_MMCSD_FS_BOOT_PARTITION 1
+#define CONFIG_SPL_FS_LOAD_PAYLOAD_NAME "u-boot.img"
#endif
#else
#ifndef CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_PARTITION
#endif
/* SPL QSPI boot support */
-#ifdef CONFIG_SPL_SPI_SUPPORT
-#if defined(CONFIG_TARGET_SOCFPGA_GEN5)
-#define CONFIG_SYS_SPI_U_BOOT_OFFS 0x40000
-#elif defined(CONFIG_TARGET_SOCFPGA_ARRIA10)
-#define CONFIG_SYS_SPI_U_BOOT_OFFS 0x100000
-#endif
-#endif
/* SPL NAND boot support */
#ifdef CONFIG_SPL_NAND_SUPPORT
#endif
#endif
-/*
- * Stack setup
- */
-#if defined(CONFIG_TARGET_SOCFPGA_GEN5)
-#define CONFIG_SPL_STACK CONFIG_SYS_INIT_SP_ADDR
-#elif defined(CONFIG_TARGET_SOCFPGA_ARRIA10)
-#define CONFIG_SPL_STACK CONFIG_SYS_SPL_MALLOC_START
-#endif
-
/* Extra Environment */
#ifndef CONFIG_SPL_BUILD
"scriptaddr=0x02100000\0" \
"pxefile_addr_r=0x02200000\0" \
"ramdisk_addr_r=0x02300000\0" \
+ "socfpga_legacy_reset_compat=1\0" \
BOOTENV
#endif
projects / platform / kernel / u-boot.git / blobdiff