#include "amcc-common.h"
/* Detect Sequoia PLL input clock automatically via CPLD bit */
-#define CONFIG_SYS_CLK_FREQ ((in8(CFG_BCSR_BASE + 3) & 0x80) ? \
+#define CONFIG_SYS_CLK_FREQ ((in8(CONFIG_SYS_BCSR_BASE + 3) & 0x80) ? \
33333333 : 33000000)
/*
* Base addresses -- Note these are effective addresses where the actual
* resources get mapped (not physical addresses).
*/
-#define CFG_TLB_FOR_BOOT_FLASH 0x0003
-#define CFG_BOOT_BASE_ADDR 0xf0000000
-#define CFG_FLASH_BASE 0xfc000000 /* start of FLASH */
-#define CFG_NAND_ADDR 0xd0000000 /* NAND Flash */
-#define CFG_OCM_BASE 0xe0010000 /* ocm */
-#define CFG_OCM_DATA_ADDR CFG_OCM_BASE
-#define CFG_PCI_BASE 0xe0000000 /* Internal PCI regs */
-#define CFG_PCI_MEMBASE 0x80000000 /* mapped pci memory */
-#define CFG_PCI_MEMBASE1 CFG_PCI_MEMBASE + 0x10000000
-#define CFG_PCI_MEMBASE2 CFG_PCI_MEMBASE1 + 0x10000000
-#define CFG_PCI_MEMBASE3 CFG_PCI_MEMBASE2 + 0x10000000
+#define CONFIG_SYS_TLB_FOR_BOOT_FLASH 0x0003
+#define CONFIG_SYS_BOOT_BASE_ADDR 0xf0000000
+#define CONFIG_SYS_FLASH_BASE 0xfc000000 /* start of FLASH */
+#define CONFIG_SYS_NAND_ADDR 0xd0000000 /* NAND Flash */
+#define CONFIG_SYS_OCM_BASE 0xe0010000 /* ocm */
+#define CONFIG_SYS_OCM_DATA_ADDR CONFIG_SYS_OCM_BASE
+#define CONFIG_SYS_PCI_BASE 0xe0000000 /* Internal PCI regs */
+#define CONFIG_SYS_PCI_MEMBASE 0x80000000 /* mapped pci memory */
+#define CONFIG_SYS_PCI_MEMBASE1 CONFIG_SYS_PCI_MEMBASE + 0x10000000
+#define CONFIG_SYS_PCI_MEMBASE2 CONFIG_SYS_PCI_MEMBASE1 + 0x10000000
+#define CONFIG_SYS_PCI_MEMBASE3 CONFIG_SYS_PCI_MEMBASE2 + 0x10000000
/* Don't change either of these */
-#define CFG_PERIPHERAL_BASE 0xef600000 /* internal peripherals */
+#define CONFIG_SYS_PERIPHERAL_BASE 0xef600000 /* internal peripherals */
-#define CFG_USB2D0_BASE 0xe0000100
-#define CFG_USB_DEVICE 0xe0000000
-#define CFG_USB_HOST 0xe0000400
-#define CFG_BCSR_BASE 0xc0000000
+#define CONFIG_SYS_USB2D0_BASE 0xe0000100
+#define CONFIG_SYS_USB_DEVICE 0xe0000000
+#define CONFIG_SYS_USB_HOST 0xe0000400
+#define CONFIG_SYS_BCSR_BASE 0xc0000000
/*
* Initial RAM & stack pointer
*/
/* 440EPx/440GRx have 16KB of internal SRAM, so no need for D-Cache */
-#define CFG_INIT_RAM_ADDR CFG_OCM_BASE /* OCM */
-#define CFG_INIT_RAM_END (4 << 10)
-#define CFG_GBL_DATA_SIZE 256 /* num bytes initial data */
-#define CFG_GBL_DATA_OFFSET (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE)
-#define CFG_INIT_SP_OFFSET CFG_POST_WORD_ADDR
+#define CONFIG_SYS_INIT_RAM_ADDR CONFIG_SYS_OCM_BASE /* OCM */
+#define CONFIG_SYS_INIT_RAM_END (4 << 10)
+#define CONFIG_SYS_GBL_DATA_SIZE 256 /* num bytes initial data */
+#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_END - CONFIG_SYS_GBL_DATA_SIZE)
+#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_POST_WORD_ADDR
/*
* Serial Port
*/
-#define CFG_EXT_SERIAL_CLOCK 11059200 /* ext. 11.059MHz clk */
+#define CONFIG_SYS_EXT_SERIAL_CLOCK 11059200 /* ext. 11.059MHz clk */
/* define this if you want console on UART1 */
#undef CONFIG_UART1_CONSOLE
/*
* FLASH related
*/
-#define CFG_FLASH_CFI /* The flash is CFI compatible */
+#define CONFIG_SYS_FLASH_CFI /* The flash is CFI compatible */
#define CONFIG_FLASH_CFI_DRIVER /* Use common CFI driver */
-#define CFG_FLASH_BANKS_LIST { CFG_FLASH_BASE }
+#define CONFIG_SYS_FLASH_BANKS_LIST { CONFIG_SYS_FLASH_BASE }
-#define CFG_MAX_FLASH_BANKS 1 /* max number of memory banks */
-#define CFG_MAX_FLASH_SECT 512 /* max number of sectors on one chip */
+#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* max number of memory banks */
+#define CONFIG_SYS_MAX_FLASH_SECT 512 /* max number of sectors on one chip */
-#define CFG_FLASH_ERASE_TOUT 120000 /* Timeout for Flash Erase (in ms) */
-#define CFG_FLASH_WRITE_TOUT 500 /* Timeout for Flash Write (in ms) */
+#define CONFIG_SYS_FLASH_ERASE_TOUT 120000 /* Timeout for Flash Erase (in ms) */
+#define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Timeout for Flash Write (in ms) */
-#define CFG_FLASH_USE_BUFFER_WRITE 1 /* use buffered writes (20x faster) */
-#define CFG_FLASH_PROTECTION 1 /* use hardware flash protection */
+#define CONFIG_SYS_FLASH_USE_BUFFER_WRITE 1 /* use buffered writes (20x faster) */
+#define CONFIG_SYS_FLASH_PROTECTION 1 /* use hardware flash protection */
-#define CFG_FLASH_EMPTY_INFO /* print 'E' for empty sector on flinfo */
-#define CFG_FLASH_QUIET_TEST 1 /* don't warn upon unknown flash */
+#define CONFIG_SYS_FLASH_EMPTY_INFO /* print 'E' for empty sector on flinfo */
+#define CONFIG_SYS_FLASH_QUIET_TEST 1 /* don't warn upon unknown flash */
#ifdef CONFIG_ENV_IS_IN_FLASH
#define CONFIG_ENV_SECT_SIZE 0x20000 /* size of one complete sector */
-#define CONFIG_ENV_ADDR ((-CFG_MONITOR_LEN)-CONFIG_ENV_SECT_SIZE)
+#define CONFIG_ENV_ADDR ((-CONFIG_SYS_MONITOR_LEN)-CONFIG_ENV_SECT_SIZE)
#define CONFIG_ENV_SIZE 0x2000 /* Total Size of Environment Sector */
/* Address and size of Redundant Environment Sector */
* set up. While still running from cache, I experienced problems accessing
* the NAND controller. sr - 2006-08-25
*/
-#define CFG_NAND_BOOT_SPL_SRC 0xfffff000 /* SPL location */
-#define CFG_NAND_BOOT_SPL_SIZE (4 << 10) /* SPL size */
-#define CFG_NAND_BOOT_SPL_DST (CFG_OCM_BASE + (12 << 10)) /* Copy SPL here */
-#define CFG_NAND_U_BOOT_DST 0x01000000 /* Load NUB to this addr */
-#define CFG_NAND_U_BOOT_START CFG_NAND_U_BOOT_DST /* Start NUB from */
+#define CONFIG_SYS_NAND_BOOT_SPL_SRC 0xfffff000 /* SPL location */
+#define CONFIG_SYS_NAND_BOOT_SPL_SIZE (4 << 10) /* SPL size */
+#define CONFIG_SYS_NAND_BOOT_SPL_DST (CONFIG_SYS_OCM_BASE + (12 << 10)) /* Copy SPL here */
+#define CONFIG_SYS_NAND_U_BOOT_DST 0x01000000 /* Load NUB to this addr */
+#define CONFIG_SYS_NAND_U_BOOT_START CONFIG_SYS_NAND_U_BOOT_DST /* Start NUB from */
/* this addr */
-#define CFG_NAND_BOOT_SPL_DELTA (CFG_NAND_BOOT_SPL_SRC - CFG_NAND_BOOT_SPL_DST)
+#define CONFIG_SYS_NAND_BOOT_SPL_DELTA (CONFIG_SYS_NAND_BOOT_SPL_SRC - CONFIG_SYS_NAND_BOOT_SPL_DST)
/*
* Define the partitioning of the NAND chip (only RAM U-Boot is needed here)
*/
-#define CFG_NAND_U_BOOT_OFFS (16 << 10) /* Offset to RAM U-Boot image */
-#define CFG_NAND_U_BOOT_SIZE (512 << 10) /* Size of RAM U-Boot image */
+#define CONFIG_SYS_NAND_U_BOOT_OFFS (16 << 10) /* Offset to RAM U-Boot image */
+#define CONFIG_SYS_NAND_U_BOOT_SIZE (512 << 10) /* Size of RAM U-Boot image */
/*
* Now the NAND chip has to be defined (no autodetection used!)
*/
-#define CFG_NAND_PAGE_SIZE 512 /* NAND chip page size */
-#define CFG_NAND_BLOCK_SIZE (16 << 10) /* NAND chip block size */
-#define CFG_NAND_PAGE_COUNT 32 /* NAND chip page count */
-#define CFG_NAND_BAD_BLOCK_POS 5 /* Location of bad block marker */
-#undef CFG_NAND_4_ADDR_CYCLE /* No fourth addr used (<=32MB) */
-
-#define CFG_NAND_ECCSIZE 256
-#define CFG_NAND_ECCBYTES 3
-#define CFG_NAND_ECCSTEPS (CFG_NAND_PAGE_SIZE / CFG_NAND_ECCSIZE)
-#define CFG_NAND_OOBSIZE 16
-#define CFG_NAND_ECCTOTAL (CFG_NAND_ECCBYTES * CFG_NAND_ECCSTEPS)
-#define CFG_NAND_ECCPOS {0, 1, 2, 3, 6, 7}
+#define CONFIG_SYS_NAND_PAGE_SIZE 512 /* NAND chip page size */
+#define CONFIG_SYS_NAND_BLOCK_SIZE (16 << 10) /* NAND chip block size */
+#define CONFIG_SYS_NAND_PAGE_COUNT 32 /* NAND chip page count */
+#define CONFIG_SYS_NAND_BAD_BLOCK_POS 5 /* Location of bad block marker */
+#undef CONFIG_SYS_NAND_4_ADDR_CYCLE /* No fourth addr used (<=32MB) */
+
+#define CONFIG_SYS_NAND_ECCSIZE 256
+#define CONFIG_SYS_NAND_ECCBYTES 3
+#define CONFIG_SYS_NAND_ECCSTEPS (CONFIG_SYS_NAND_PAGE_SIZE / CONFIG_SYS_NAND_ECCSIZE)
+#define CONFIG_SYS_NAND_OOBSIZE 16
+#define CONFIG_SYS_NAND_ECCTOTAL (CONFIG_SYS_NAND_ECCBYTES * CONFIG_SYS_NAND_ECCSTEPS)
+#define CONFIG_SYS_NAND_ECCPOS {0, 1, 2, 3, 6, 7}
#ifdef CONFIG_ENV_IS_IN_NAND
/*
* For NAND booting the environment is embedded in the U-Boot image. Please take
* look at the file board/amcc/sequoia/u-boot-nand.lds for details.
*/
-#define CONFIG_ENV_SIZE CFG_NAND_BLOCK_SIZE
-#define CONFIG_ENV_OFFSET (CFG_NAND_U_BOOT_OFFS + CONFIG_ENV_SIZE)
+#define CONFIG_ENV_SIZE CONFIG_SYS_NAND_BLOCK_SIZE
+#define CONFIG_ENV_OFFSET (CONFIG_SYS_NAND_U_BOOT_OFFS + CONFIG_ENV_SIZE)
#define CONFIG_ENV_OFFSET_REDUND (CONFIG_ENV_OFFSET + CONFIG_ENV_SIZE)
#endif
/*
* DDR SDRAM
*/
-#define CFG_MBYTES_SDRAM (256) /* 256MB */
+#define CONFIG_SYS_MBYTES_SDRAM (256) /* 256MB */
#if !defined(CONFIG_NAND_U_BOOT) && !defined(CONFIG_NAND_SPL)
#define CONFIG_DDR_DATA_EYE /* use DDR2 optimization */
#endif
-#define CFG_MEM_TOP_HIDE (4 << 10) /* don't use last 4kbytes */
+#define CONFIG_SYS_MEM_TOP_HIDE (4 << 10) /* don't use last 4kbytes */
/* 440EPx errata CHIP 11 */
/*
* I2C
*/
-#define CFG_I2C_SPEED 400000 /* I2C speed and slave address */
+#define CONFIG_SYS_I2C_SPEED 400000 /* I2C speed and slave address */
-#define CFG_I2C_MULTI_EEPROMS
-#define CFG_I2C_EEPROM_ADDR (0xa8>>1)
-#define CFG_I2C_EEPROM_ADDR_LEN 1
-#define CFG_EEPROM_PAGE_WRITE_BITS 3
-#define CFG_EEPROM_PAGE_WRITE_DELAY_MS 10
+#define CONFIG_SYS_I2C_MULTI_EEPROMS
+#define CONFIG_SYS_I2C_EEPROM_ADDR (0xa8>>1)
+#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1
+#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 3
+#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 10
/* I2C SYSMON (LM75, AD7414 is almost compatible) */
#define CONFIG_DTT_LM75 1 /* ON Semi's LM75 */
#define CONFIG_DTT_AD7414 1 /* use AD7414 */
#define CONFIG_DTT_SENSORS {0} /* Sensor addresses */
-#define CFG_DTT_MAX_TEMP 70
-#define CFG_DTT_LOW_TEMP -30
-#define CFG_DTT_HYSTERESIS 3
+#define CONFIG_SYS_DTT_MAX_TEMP 70
+#define CONFIG_SYS_DTT_LOW_TEMP -30
+#define CONFIG_SYS_DTT_HYSTERESIS 3
/*
* Default environment variables
#ifdef CONFIG_440EPX
#define CONFIG_USB_OHCI_NEW
#define CONFIG_USB_STORAGE
-#define CFG_OHCI_BE_CONTROLLER
+#define CONFIG_SYS_OHCI_BE_CONTROLLER
-#undef CFG_USB_OHCI_BOARD_INIT
-#define CFG_USB_OHCI_CPU_INIT 1
-#define CFG_USB_OHCI_REGS_BASE CFG_USB_HOST
-#define CFG_USB_OHCI_SLOT_NAME "ppc440"
-#define CFG_USB_OHCI_MAX_ROOT_PORTS 15
+#undef CONFIG_SYS_USB_OHCI_BOARD_INIT
+#define CONFIG_SYS_USB_OHCI_CPU_INIT 1
+#define CONFIG_SYS_USB_OHCI_REGS_BASE CONFIG_SYS_USB_HOST
+#define CONFIG_SYS_USB_OHCI_SLOT_NAME "ppc440"
+#define CONFIG_SYS_USB_OHCI_MAX_ROOT_PORTS 15
/* Comment this out to enable USB 1.1 device */
#define USB_2_0_DEVICE
#endif
#ifndef CONFIG_RAINIER
-#define CFG_POST_FPU_ON CFG_POST_FPU
+#define CONFIG_SYS_POST_FPU_ON CONFIG_SYS_POST_FPU
#else
-#define CFG_POST_FPU_ON 0
+#define CONFIG_SYS_POST_FPU_ON 0
#endif
/* POST support */
-#define CONFIG_POST (CFG_POST_CACHE | \
- CFG_POST_CPU | \
- CFG_POST_ETHER | \
- CFG_POST_FPU_ON | \
- CFG_POST_I2C | \
- CFG_POST_MEMORY | \
- CFG_POST_SPR | \
- CFG_POST_UART)
-
-#define CFG_POST_WORD_ADDR (CFG_GBL_DATA_OFFSET - 0x4)
+#define CONFIG_POST (CONFIG_SYS_POST_CACHE | \
+ CONFIG_SYS_POST_CPU | \
+ CONFIG_SYS_POST_ETHER | \
+ CONFIG_SYS_POST_FPU_ON | \
+ CONFIG_SYS_POST_I2C | \
+ CONFIG_SYS_POST_MEMORY | \
+ CONFIG_SYS_POST_SPR | \
+ CONFIG_SYS_POST_UART)
+
+#define CONFIG_SYS_POST_WORD_ADDR (CONFIG_SYS_GBL_DATA_OFFSET - 0x4)
#define CONFIG_LOGBUFFER
-#define CFG_POST_CACHE_ADDR 0x7fff0000 /* free virtual address */
+#define CONFIG_SYS_POST_CACHE_ADDR 0x7fff0000 /* free virtual address */
-#define CFG_CONSOLE_IS_IN_ENV /* Otherwise it catches logbuffer as output */
+#define CONFIG_SYS_CONSOLE_IS_IN_ENV /* Otherwise it catches logbuffer as output */
#define CONFIG_SUPPORT_VFAT
/* General PCI */
#define CONFIG_PCI /* include pci support */
#define CONFIG_PCI_PNP /* do pci plug-and-play */
-#define CFG_PCI_CACHE_LINE_SIZE 0 /* to avoid problems with PNP */
+#define CONFIG_SYS_PCI_CACHE_LINE_SIZE 0 /* to avoid problems with PNP */
#define CONFIG_PCI_SCAN_SHOW /* show pci devices on startup */
-#define CFG_PCI_TARGBASE 0x80000000 /* PCIaddr mapped to */
- /* CFG_PCI_MEMBASE */
+#define CONFIG_SYS_PCI_TARGBASE 0x80000000 /* PCIaddr mapped to */
+ /* CONFIG_SYS_PCI_MEMBASE */
/* Board-specific PCI */
-#define CFG_PCI_TARGET_INIT
-#define CFG_PCI_MASTER_INIT
+#define CONFIG_SYS_PCI_TARGET_INIT
+#define CONFIG_SYS_PCI_MASTER_INIT
-#define CFG_PCI_SUBSYS_VENDORID 0x10e8 /* AMCC */
-#define CFG_PCI_SUBSYS_ID 0xcafe /* Whatever */
+#define CONFIG_SYS_PCI_SUBSYS_VENDORID 0x10e8 /* AMCC */
+#define CONFIG_SYS_PCI_SUBSYS_ID 0xcafe /* Whatever */
/*
* External Bus Controller (EBC) Setup
* On Sequoia CS0 and CS3 are switched when configuring for NAND booting
*/
#if !defined(CONFIG_NAND_U_BOOT) && !defined(CONFIG_NAND_SPL)
-#define CFG_NAND_CS 3 /* NAND chip connected to CSx */
+#define CONFIG_SYS_NAND_CS 3 /* NAND chip connected to CSx */
/* Memory Bank 0 (NOR-FLASH) initialization */
-#define CFG_EBC_PB0AP 0x03017200
-#define CFG_EBC_PB0CR (CFG_FLASH_BASE | 0xda000)
+#define CONFIG_SYS_EBC_PB0AP 0x03017200
+#define CONFIG_SYS_EBC_PB0CR (CONFIG_SYS_FLASH_BASE | 0xda000)
/* Memory Bank 3 (NAND-FLASH) initialization */
-#define CFG_EBC_PB3AP 0x018003c0
-#define CFG_EBC_PB3CR (CFG_NAND_ADDR | 0x1c000)
+#define CONFIG_SYS_EBC_PB3AP 0x018003c0
+#define CONFIG_SYS_EBC_PB3CR (CONFIG_SYS_NAND_ADDR | 0x1c000)
#else
-#define CFG_NAND_CS 0 /* NAND chip connected to CSx */
+#define CONFIG_SYS_NAND_CS 0 /* NAND chip connected to CSx */
/* Memory Bank 3 (NOR-FLASH) initialization */
-#define CFG_EBC_PB3AP 0x03017200
-#define CFG_EBC_PB3CR (CFG_FLASH_BASE | 0xda000)
+#define CONFIG_SYS_EBC_PB3AP 0x03017200
+#define CONFIG_SYS_EBC_PB3CR (CONFIG_SYS_FLASH_BASE | 0xda000)
/* Memory Bank 0 (NAND-FLASH) initialization */
-#define CFG_EBC_PB0AP 0x018003c0
-#define CFG_EBC_PB0CR (CFG_NAND_ADDR | 0x1c000)
+#define CONFIG_SYS_EBC_PB0AP 0x018003c0
+#define CONFIG_SYS_EBC_PB0CR (CONFIG_SYS_NAND_ADDR | 0x1c000)
#endif
/* Memory Bank 2 (CPLD) initialization */
-#define CFG_EBC_PB2AP 0x24814580
-#define CFG_EBC_PB2CR (CFG_BCSR_BASE | 0x38000)
+#define CONFIG_SYS_EBC_PB2AP 0x24814580
+#define CONFIG_SYS_EBC_PB2CR (CONFIG_SYS_BCSR_BASE | 0x38000)
-#define CFG_BCSR5_PCI66EN 0x80
+#define CONFIG_SYS_BCSR5_PCI66EN 0x80
/*
* NAND FLASH
*/
-#define CFG_MAX_NAND_DEVICE 1
+#define CONFIG_SYS_MAX_NAND_DEVICE 1
#define NAND_MAX_CHIPS 1
-#define CFG_NAND_BASE (CFG_NAND_ADDR + CFG_NAND_CS)
-#define CFG_NAND_SELECT_DEVICE 1 /* nand driver supports mutipl. chips */
+#define CONFIG_SYS_NAND_BASE (CONFIG_SYS_NAND_ADDR + CONFIG_SYS_NAND_CS)
+#define CONFIG_SYS_NAND_SELECT_DEVICE 1 /* nand driver supports mutipl. chips */
/*
* PPC440 GPIO Configuration
*/
/* test-only: take GPIO init from pcs440ep ???? in config file */
-#define CFG_4xx_GPIO_TABLE { /* Out GPIO Alternate1 Alternate2 Alternate3 */ \
+#define CONFIG_SYS_4xx_GPIO_TABLE { /* Out GPIO Alternate1 Alternate2 Alternate3 */ \
{ \
/* GPIO Core 0 */ \
{GPIO0_BASE, GPIO_BI , GPIO_ALT1, GPIO_OUT_0}, /* GPIO0 EBC_ADDR(7) DMA_REQ(2) */ \
#define CONFIG_BIOSEMU /* x86 bios emulator for vga bios */
#define CONFIG_ATI_RADEON_FB /* use radeon framebuffer driver */
#define VIDEO_IO_OFFSET 0xe8000000
-#define CFG_ISA_IO_BASE_ADDRESS VIDEO_IO_OFFSET
+#define CONFIG_SYS_ISA_IO_BASE_ADDRESS VIDEO_IO_OFFSET
#define CONFIG_VIDEO_SW_CURSOR
#define CONFIG_VIDEO_LOGO
#define CONFIG_CFB_CONSOLE
projects / platform / kernel / u-boot.git / blobdiff