Prepare v2023.10

[platform/kernel/u-boot.git] / include / configs / rut.h

diff --git a/include/configs/rut.h b/include/configs/rut.h
index 0dcdb10..4002bc4 100644 (file)
--- a/include/configs/rut.h
+++ b/include/configs/rut.h
@@ -13,42 +13,28 @@
 #ifndef __CONFIG_RUT_H
 #define __CONFIG_RUT_H
 
-#define CONFIG_SIEMENS_MACH_TYPE       MACH_TYPE_RUT
-
 #include "siemens-am33x-common.h"
 
 #define RUT_IOCTRL_VAL 0x18b
 #define DDR_PLL_FREQ   303
 
  /* Physical Memory Map */
-#define CONFIG_MAX_RAM_BANK_SIZE       (256 << 20) /* 256 MiB */
-
-/* I2C Configuration */
-#define CONFIG_SYS_I2C_SPEED           100000
-
-#define CONFIG_SYS_I2C_EEPROM_ADDR              0x50
-#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN          2
-#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS       6       /* 64 byte pages */
-#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS   10      /* take up to 10 msec */
-
-#define CONFIG_FACTORYSET
+#define CFG_MAX_RAM_BANK_SIZE  (256 << 20) /* 256 MiB */
 
 /* Watchdog */
 #define WATCHDOG_TRIGGER_GPIO  14
 
-#ifndef CONFIG_SPL_BUILD
-
 /* Use common default */
 
 /* Default env settings */
-#define CONFIG_EXTRA_ENV_SETTINGS \
+#define CFG_EXTRA_ENV_SETTINGS \
        "hostname=rut\0" \
        "ubi_off=2048\0"\
        "nand_img_size=0x500000\0" \
        "splashpos=m,m\0" \
        "optargs=fixrtc --no-log consoleblank=0 \0" \
-       CONFIG_ENV_SETTINGS_V1 \
-       CONFIG_ENV_SETTINGS_NAND_V1 \
+       CFG_ENV_SETTINGS_V1 \
+       CFG_ENV_SETTINGS_NAND_V1 \
        "mmc_dev=0\0" \
        "mmc_root=/dev/mmcblk0p2 rw\0" \
        "mmc_root_fs_type=ext4 rootwait\0" \
@@ -71,52 +57,4 @@
                "bootm ${kloadaddr}\0" \
        ""
 
-#ifndef CONFIG_RESTORE_FLASH
-/* set to negative value for no autoboot */
-
-#define CONFIG_BOOTCOMMAND \
-       "if mmc rescan; then " \
-               "echo SD/MMC found on device ${mmc_dev};" \
-               "if run loadbootenv; then " \
-                       "echo Loaded environment from ${bootenv};" \
-                       "run importbootenv;" \
-               "fi;" \
-               "if test -n $uenvcmd; then " \
-                       "echo Running uenvcmd ...;" \
-                       "run uenvcmd;" \
-               "fi;" \
-               "if run mmc_load_uimage; then " \
-                       "run mmc_args;" \
-                       "bootm ${kloadaddr};" \
-               "fi;" \
-       "fi;" \
-       "run nand_boot;" \
-       "reset;"
-
-#else
-
-#define CONFIG_BOOTCOMMAND                     \
-       "setenv autoload no; "                  \
-       "dhcp; "                                \
-       "if tftp 80000000 debrick.scr; then "   \
-               "source 80000000; "             \
-       "fi"
-#endif
-
-#endif /* CONFIG_SPL_BUILD */
-
-#if defined(CONFIG_VIDEO)
-#define CONFIG_VIDEO_DA8XX
-#define CONFIG_SPLASH_SCREEN
-#define CONFIG_SPLASH_SCREEN_ALIGN
-#define CONFIG_VIDEO_LOGO
-#define CONFIG_VIDEO_BMP_RLE8
-#define CONFIG_VIDEO_BMP_LOGO
-#define DA8XX_LCD_CNTL_BASE    LCD_CNTL_BASE
-
-#define BOARD_LCD_RESET                115     /* Bank 3 pin 19 */
-#define CONFIG_FORMIKE
-#define DISPL_PLL_SPREAD_SPECTRUM
-#endif
-
 #endif /* ! __CONFIG_RUT_H */