#include <linux/stringify.h>
-#if defined(CONFIG_TARGET_P1020MBG)
-#define CONFIG_BOARDNAME "P1020MBG-PC"
-#define CONFIG_VSC7385_ENET
-#define CONFIG_SLIC
-#define __SW_BOOT_MASK 0x03
-#define __SW_BOOT_NOR 0xe4
-#define __SW_BOOT_SD 0x54
-#define CONFIG_SYS_L2_SIZE (256 << 10)
-#endif
-
-#if defined(CONFIG_TARGET_P1020UTM)
-#define CONFIG_BOARDNAME "P1020UTM-PC"
-#define __SW_BOOT_MASK 0x03
-#define __SW_BOOT_NOR 0xe0
-#define __SW_BOOT_SD 0x50
-#define CONFIG_SYS_L2_SIZE (256 << 10)
-#endif
-
#if defined(CONFIG_TARGET_P1020RDB_PC)
#define CONFIG_BOARDNAME "P1020RDB-PC"
-#define CONFIG_NAND_FSL_ELBC
#define CONFIG_VSC7385_ENET
#define CONFIG_SLIC
#define __SW_BOOT_MASK 0x03
*/
#if defined(CONFIG_TARGET_P1020RDB_PD)
#define CONFIG_BOARDNAME "P1020RDB-PD"
-#define CONFIG_NAND_FSL_ELBC
#define CONFIG_VSC7385_ENET
#define CONFIG_SLIC
#define __SW_BOOT_MASK 0x03
*/
#endif
-#if defined(CONFIG_TARGET_P1021RDB)
-#define CONFIG_BOARDNAME "P1021RDB-PC"
-#define CONFIG_NAND_FSL_ELBC
-#define CONFIG_VSC7385_ENET
-#define CONFIG_SYS_LBC_LBCR 0x00080000 /* Implement conversion of
- addresses in the LBC */
-#define __SW_BOOT_MASK 0x03
-#define __SW_BOOT_NOR 0x5c
-#define __SW_BOOT_SPI 0x1c
-#define __SW_BOOT_SD 0x9c
-#define __SW_BOOT_NAND 0xec
-#define __SW_BOOT_PCIE 0x6c
-#define CONFIG_SYS_L2_SIZE (256 << 10)
-/*
- * Dynamic MTD Partition support with mtdparts
- */
-#endif
-
-#if defined(CONFIG_TARGET_P1024RDB)
-#define CONFIG_BOARDNAME "P1024RDB"
-#define CONFIG_NAND_FSL_ELBC
-#define CONFIG_SLIC
-#define __SW_BOOT_MASK 0xf3
-#define __SW_BOOT_NOR 0x00
-#define __SW_BOOT_SPI 0x08
-#define __SW_BOOT_SD 0x04
-#define __SW_BOOT_NAND 0x0c
-#define CONFIG_SYS_L2_SIZE (256 << 10)
-#endif
-
-#if defined(CONFIG_TARGET_P1025RDB)
-#define CONFIG_BOARDNAME "P1025RDB"
-#define CONFIG_NAND_FSL_ELBC
-#define CONFIG_SLIC
-
-#define CONFIG_SYS_LBC_LBCR 0x00080000 /* Implement conversion of
- addresses in the LBC */
-#define __SW_BOOT_MASK 0xf3
-#define __SW_BOOT_NOR 0x00
-#define __SW_BOOT_SPI 0x08
-#define __SW_BOOT_SD 0x04
-#define __SW_BOOT_NAND 0x0c
-#define CONFIG_SYS_L2_SIZE (256 << 10)
-#endif
-
#if defined(CONFIG_TARGET_P2020RDB)
#define CONFIG_BOARDNAME "P2020RDB-PC"
-#define CONFIG_NAND_FSL_ELBC
#define CONFIG_VSC7385_ENET
#define __SW_BOOT_MASK 0x03
#define __SW_BOOT_NOR 0xc8
#ifdef CONFIG_SPL_BUILD
#define CONFIG_SPL_COMMON_INIT_DDR
#endif
-#endif
-
-#ifdef CONFIG_SPIFLASH
+#elif defined(CONFIG_SPIFLASH)
#define CONFIG_SPL_SPI_FLASH_MINIMAL
#define CONFIG_SPL_FLUSH_IMAGE
#define CONFIG_SPL_TARGET "u-boot-with-spl.bin"
#ifdef CONFIG_SPL_BUILD
#define CONFIG_SPL_COMMON_INIT_DDR
#endif
-#endif
-
-#ifdef CONFIG_MTD_RAW_NAND
+#elif defined(CONFIG_MTD_RAW_NAND)
#ifdef CONFIG_TPL_BUILD
#define CONFIG_SPL_FLUSH_IMAGE
#define CONFIG_SPL_NAND_INIT
#define CONFIG_PCIE2 /* PCIE controller 2 (slot 2) */
#define CONFIG_SYS_PCI_64BIT /* enable 64-bit PCI resources */
-#define CONFIG_ENV_OVERWRITE
-
#define CONFIG_SYS_SATA_MAX_DEVICE 2
#define CONFIG_LBA48
#else
#define CONFIG_SYS_CLK_FREQ 66666666
#endif
-#define CONFIG_DDR_CLK_FREQ 66666666
#define CONFIG_HWCONFIG
/*
#define CONFIG_ENABLE_36BIT_PHYS
-#ifdef CONFIG_PHYS_64BIT
-#define CONFIG_ADDR_MAP 1
-#define CONFIG_SYS_NUM_ADDR_MAP 16 /* number of TLB1 entries */
-#endif
-
#define CONFIG_SYS_CCSRBAR 0xffe00000
#define CONFIG_SYS_CCSRBAR_PHYS_LOW CONFIG_SYS_CCSRBAR
/* DDR Setup */
#define CONFIG_SYS_DDR_RAW_TIMING
-#define CONFIG_DDR_SPD
#define CONFIG_SYS_SPD_BUS_NUM 1
#define SPD_EEPROM_ADDRESS 0x52
-#if (defined(CONFIG_TARGET_P1020MBG) || defined(CONFIG_TARGET_P1020RDB_PD))
+#if defined(CONFIG_TARGET_P1020RDB_PD)
#define CONFIG_SYS_SDRAM_SIZE_LAW LAW_SIZE_2G
#define CONFIG_CHIP_SELECTS_PER_CTRL 2
#else
/*
* Local Bus Definitions
*/
-#if (defined(CONFIG_TARGET_P1020MBG) || defined(CONFIG_TARGET_P1020RDB_PD))
+#if defined(CONFIG_TARGET_P1020RDB_PD)
#define CONFIG_SYS_MAX_FLASH_SECT 512 /* 64M */
#define CONFIG_SYS_FLASH_BASE 0xec000000
-#elif defined(CONFIG_TARGET_P1020UTM)
-#define CONFIG_SYS_MAX_FLASH_SECT 256 /* 32M */
-#define CONFIG_SYS_FLASH_BASE 0xee000000
#else
#define CONFIG_SYS_MAX_FLASH_SECT 128 /* 16M */
#define CONFIG_SYS_FLASH_BASE 0xef000000
#define CONFIG_SYS_NAND_BASE_LIST { CONFIG_SYS_NAND_BASE }
#define CONFIG_SYS_MAX_NAND_DEVICE 1
-#if defined(CONFIG_TARGET_P1020RDB_PD)
-#define CONFIG_SYS_NAND_BLOCK_SIZE (128 * 1024)
-#else
-#define CONFIG_SYS_NAND_BLOCK_SIZE (16 * 1024)
-#endif
#define CONFIG_SYS_NAND_BR_PRELIM (BR_PHYS_ADDR(CONFIG_SYS_NAND_BASE_PHYS) \
| (2<<BR_DECC_SHIFT) /* Use HW ECC */ \
#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET
#define CONFIG_SYS_MONITOR_LEN (768 * 1024)
-#define CONFIG_SYS_MALLOC_LEN (1024 * 1024)/* Reserved for malloc */
#define CONFIG_SYS_CPLD_BASE 0xffa00000
#ifdef CONFIG_PHYS_64BIT
/* Vsc7385 switch */
#ifdef CONFIG_VSC7385_ENET
+#define __VSCFW_ADDR "vscfw_addr=ef000000"
#define CONFIG_SYS_VSC7385_BASE 0xffb00000
#ifdef CONFIG_PHYS_64BIT
#define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_CCSRBAR+0x4600)
/* I2C */
-#ifndef CONFIG_DM_I2C
-#define CONFIG_SYS_I2C
-#define CONFIG_SYS_FSL_I2C_SPEED 400000
-#define CONFIG_SYS_FSL_I2C_SLAVE 0x7F
-#define CONFIG_SYS_FSL_I2C_OFFSET 0x3000
-#define CONFIG_SYS_FSL_I2C2_SPEED 400000
-#define CONFIG_SYS_FSL_I2C2_SLAVE 0x7F
-#define CONFIG_SYS_FSL_I2C2_OFFSET 0x3100
+#if !CONFIG_IS_ENABLED(DM_I2C)
#define CONFIG_SYS_I2C_NOPROBES { {0, 0x29} }
-#else
-#define CONFIG_I2C_SET_DEFAULT_BUS_NUM
-#define CONFIG_I2C_DEFAULT_BUS_NUMBER 0
#endif
-#define CONFIG_SYS_I2C_FSL
-#define CONFIG_SYS_I2C_EEPROM_ADDR 0x52
#define CONFIG_SYS_SPD_BUS_NUM 1 /* For rom_loc and flash bank */
/*
* I2C2 EEPROM
*/
-#undef CONFIG_ID_EEPROM
#define CONFIG_RTC_PT7C4338
#define CONFIG_SYS_I2C_RTC_ADDR 0x68
#define CONFIG_SYS_I2C_PCA9557_ADDR 0x18
/* enable read and write access to EEPROM */
-#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1
-#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 3
-#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 5
#if defined(CONFIG_PCI)
/*
#define CONFIG_SYS_PCIE1_IO_PHYS 0xffc00000
#endif
-#if !defined(CONFIG_DM_PCI)
-#define CONFIG_FSL_PCI_INIT /* Use common FSL init code */
-#define CONFIG_PCI_INDIRECT_BRIDGE
-#define CONFIG_SYS_PCIE2_NAME "PCIe SLOT"
-#ifdef CONFIG_PHYS_64BIT
-#define CONFIG_SYS_PCIE2_MEM_BUS 0xc0000000
-#else
-#define CONFIG_SYS_PCIE2_MEM_BUS 0xa0000000
-#endif
-#define CONFIG_SYS_PCIE2_MEM_SIZE 0x20000000 /* 512M */
-#define CONFIG_SYS_PCIE2_IO_BUS 0x00000000
-#define CONFIG_SYS_PCIE2_IO_SIZE 0x00010000 /* 64k */
-
-#define CONFIG_SYS_PCIE1_NAME "mini PCIe SLOT"
-#ifdef CONFIG_PHYS_64BIT
-#define CONFIG_SYS_PCIE1_MEM_BUS 0x80000000
-#else
-#define CONFIG_SYS_PCIE1_MEM_BUS 0x80000000
-#endif
-#define CONFIG_SYS_PCIE1_MEM_SIZE 0x20000000 /* 512M */
-#define CONFIG_SYS_PCIE1_IO_BUS 0x00000000
-#define CONFIG_SYS_PCIE1_IO_SIZE 0x00010000 /* 64k */
-#endif
-
#define CONFIG_PCI_SCAN_SHOW /* show pci devices on startup */
#endif /* CONFIG_PCI */
#define CONFIG_HAS_ETH2
#endif /* CONFIG_TSEC_ENET */
-#ifdef CONFIG_QE
-/* QE microcode/firmware address */
-#define CONFIG_SYS_QE_FW_ADDR 0xefec0000
-#define CONFIG_SYS_QE_FMAN_FW_LENGTH 0x10000
-#endif /* CONFIG_QE */
-
-#ifdef CONFIG_TARGET_P1025RDB
-/*
- * QE UEC ethernet configuration
- */
-#define CONFIG_MIIM_ADDRESS (CONFIG_SYS_CCSRBAR + 0x82120)
-
-#undef CONFIG_UEC_ETH
-#define CONFIG_PHY_MODE_NEED_CHANGE
-
-#define CONFIG_UEC_ETH1 /* ETH1 */
-#define CONFIG_HAS_ETH0
-
-#ifdef CONFIG_UEC_ETH1
-#define CONFIG_SYS_UEC1_UCC_NUM 0 /* UCC1 */
-#define CONFIG_SYS_UEC1_RX_CLK QE_CLK12 /* CLK12 for MII */
-#define CONFIG_SYS_UEC1_TX_CLK QE_CLK9 /* CLK9 for MII */
-#define CONFIG_SYS_UEC1_ETH_TYPE FAST_ETH
-#define CONFIG_SYS_UEC1_PHY_ADDR 0x0 /* 0x0 for MII */
-#define CONFIG_SYS_UEC1_INTERFACE_TYPE PHY_INTERFACE_MODE_RMII
-#define CONFIG_SYS_UEC1_INTERFACE_SPEED 100
-#endif /* CONFIG_UEC_ETH1 */
-
-#define CONFIG_UEC_ETH5 /* ETH5 */
-#define CONFIG_HAS_ETH1
-
-#ifdef CONFIG_UEC_ETH5
-#define CONFIG_SYS_UEC5_UCC_NUM 4 /* UCC5 */
-#define CONFIG_SYS_UEC5_RX_CLK QE_CLK_NONE
-#define CONFIG_SYS_UEC5_TX_CLK QE_CLK13 /* CLK 13 for RMII */
-#define CONFIG_SYS_UEC5_ETH_TYPE FAST_ETH
-#define CONFIG_SYS_UEC5_PHY_ADDR 0x3 /* 0x3 for RMII */
-#define CONFIG_SYS_UEC5_INTERFACE_TYPE PHY_INTERFACE_MODE_RMII
-#define CONFIG_SYS_UEC5_INTERFACE_SPEED 100
-#endif /* CONFIG_UEC_ETH5 */
-#endif /* CONFIG_TARGET_P1025RDB */
-
/*
* Environment
*/
#if defined(CONFIG_SDCARD)
#define CONFIG_FSL_FIXED_MMC_LOCATION
-#define CONFIG_SYS_MMC_ENV_DEV 0
#elif defined(CONFIG_MTD_RAW_NAND)
#define CONFIG_ENV_RANGE (3 * CONFIG_ENV_SIZE)
#ifdef CONFIG_TPL_BUILD
/*
* Miscellaneous configurable options
*/
-#define CONFIG_SYS_LOAD_ADDR 0x2000000 /* default load address */
/*
* For booting Linux, the board info and command line data
#define CONFIG_SYS_BOOTMAPSZ (64 << 20) /* Initial Memory for Linux*/
#define CONFIG_SYS_BOOTM_LEN (64 << 20) /* Increase max gunzip size */
-#if defined(CONFIG_CMD_KGDB)
-#define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */
-#endif
-
/*
* Environment Configuration
*/
#define CONFIG_BOOTFILE "uImage"
#define CONFIG_UBOOTPATH u-boot.bin /* U-Boot image on TFTP server */
-/* default location for tftp and bootm */
-#define CONFIG_LOADADDR 1000000
-
#ifdef __SW_BOOT_NOR
#define __NOR_RST_CMD \
norboot=i2c dev 1; i2c mw 18 1 __SW_BOOT_NOR 1; \
"ramdisk_size=120000\0" \
"map_lowernorbank=i2c dev 1; i2c mw 18 1 02 1; i2c mw 18 3 fd 1\0" \
"map_uppernorbank=i2c dev 1; i2c mw 18 1 00 1; i2c mw 18 3 fd 1\0" \
+__stringify(__VSCFW_ADDR)"\0" \
__stringify(__NOR_RST_CMD)"\0" \
__stringify(__SPI_RST_CMD)"\0" \
__stringify(__SD_RST_CMD)"\0" \
__stringify(__NAND_RST_CMD)"\0" \
__stringify(__PCIE_RST_CMD)"\0"
-#define CONFIG_NFSBOOTCOMMAND \
-"setenv bootargs root=/dev/nfs rw " \
-"nfsroot=$serverip:$rootpath " \
-"ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:$netdev:off " \
-"console=$consoledev,$baudrate $othbootargs;" \
-"tftp $loadaddr $bootfile;" \
-"tftp $fdtaddr $fdtfile;" \
-"bootm $loadaddr - $fdtaddr"
-
-#define CONFIG_HDBOOT \
-"setenv bootargs root=/dev/$bdev rw rootdelay=30 " \
-"console=$consoledev,$baudrate $othbootargs;" \
-"usb start;" \
-"ext2load usb 0:1 $loadaddr /boot/$bootfile;" \
-"ext2load usb 0:1 $fdtaddr /boot/$fdtfile;" \
-"bootm $loadaddr - $fdtaddr"
-
#define CONFIG_USB_FAT_BOOT \
"setenv bootargs root=/dev/ram rw " \
"console=$consoledev,$baudrate $othbootargs " \
"console=$consoledev,$baudrate rootfstype=jffs2 $othbootargs;" \
"bootm $norbootaddr - $norfdtaddr"
-#define CONFIG_RAMBOOTCOMMAND \
-"setenv bootargs root=/dev/ram rw " \
-"console=$consoledev,$baudrate $othbootargs " \
-"ramdisk_size=$ramdisk_size;" \
-"tftp $ramdiskaddr $ramdiskfile;" \
-"tftp $loadaddr $bootfile;" \
-"tftp $fdtaddr $fdtfile;" \
-"bootm $loadaddr $ramdiskaddr $fdtaddr"
-
-#define CONFIG_BOOTCOMMAND CONFIG_HDBOOT
-
#endif /* __CONFIG_H */
projects / platform / kernel / u-boot.git / blobdiff