Prepare v2023.10

[platform/kernel/u-boot.git] / include / configs / omap3_logic.h

diff --git a/include/configs/omap3_logic.h b/include/configs/omap3_logic.h
index 886f2e9..957f1c3 100644 (file)
--- a/include/configs/omap3_logic.h
+++ b/include/configs/omap3_logic.h
@@ -14,53 +14,24 @@
 
 #include <configs/ti_omap3_common.h>
 
-/*
- * We are only ever GP parts and will utilize all of the "downloaded image"
- * area in SRAM which starts at 0x40200000 and ends at 0x4020FFFF (64KB) in
- * order to allow for BCH8 to fit in.
- */
-
-/* Hardware drivers */
-
-/* I2C */
-
-#ifdef CONFIG_SPL_BUILD
-#undef CONFIG_USB_EHCI_OMAP
-#endif
-#ifdef CONFIG_USB_EHCI_OMAP
-#define CONFIG_OMAP_EHCI_PHY1_RESET_GPIO       4
-#endif
-
 /* Board NAND Info. */
 #ifdef CONFIG_MTD_RAW_NAND
-#define CONFIG_SYS_MAX_NAND_DEVICE     1         /* Max number of */
                                                  /* NAND devices */
-#define CONFIG_SYS_NAND_5_ADDR_CYCLE
-#define CONFIG_SYS_NAND_PAGE_COUNT     64
-#define CONFIG_SYS_NAND_PAGE_SIZE      2048
-#define CONFIG_SYS_NAND_OOBSIZE                64
-#define CONFIG_SYS_NAND_BLOCK_SIZE     (128 * 1024)
-#define CONFIG_SYS_NAND_BAD_BLOCK_POS  NAND_LARGE_BADBLOCK_POS
-#define CONFIG_SYS_NAND_ECCPOS         {2, 3, 4, 5, 6, 7, 8, 9, 10, 11, 12, \
+#define CFG_SYS_NAND_ECCPOS            {2, 3, 4, 5, 6, 7, 8, 9, 10, 11, 12, \
                                         13, 14, 16, 17, 18, 19, 20, 21, 22, \
                                         23, 24, 25, 26, 27, 28, 30, 31, 32, \
                                         33, 34, 35, 36, 37, 38, 39, 40, 41, \
                                         42, 44, 45, 46, 47, 48, 49, 50, 51, \
                                         52, 53, 54, 55, 56}
 
-#define CONFIG_SYS_NAND_ECCSIZE                512
-#define CONFIG_SYS_NAND_ECCBYTES       13
-#define CONFIG_NAND_OMAP_ECCSCHEME     OMAP_ECC_BCH8_CODE_HW_DETECTION_SW
-#define CONFIG_SYS_NAND_MAX_OOBFREE    2
-#define CONFIG_SYS_NAND_MAX_ECCPOS     56
+#define CFG_SYS_NAND_ECCSIZE           512
+#define CFG_SYS_NAND_ECCBYTES  13
 #endif
 
 /* Environment information */
 
-#define CONFIG_EXTRA_ENV_SETTINGS \
+#define CFG_EXTRA_ENV_SETTINGS \
        DEFAULT_LINUX_BOOT_ENV \
-       "mtdids=" CONFIG_MTDIDS_DEFAULT "\0"    \
-       "mtdparts=" CONFIG_MTDPARTS_DEFAULT "\0" \
        "mmcdev=0\0" \
        "finduuid=part uuid mmc ${mmcdev}:2 uuid\0" \
        "mmcrootfstype=ext4 rootwait\0" \
@@ -111,7 +82,6 @@
                "nfsroot=${nfsrootpath} " \
                "ip=${ipaddr}:${tftpserver}:${gatewayip}:${netmask}::eth0:off\0" \
        "nfsrootpath=/opt/nfs-exports/omap\0" \
-       "autoload=no\0" \
        "fdtimage=" CONFIG_DEFAULT_DEVICE_TREE ".dtb\0" \
        "loadfdt=mmc rescan; " \
                "load mmc ${mmcdev} ${fdtaddr} ${fdtimage}\0" \
@@ -166,9 +136,6 @@
        "nandboot=run nandbootcommon; "\
                "bootm ${loadaddr} - ${fdtaddr}\0"\
 
-#define CONFIG_BOOTCOMMAND \
-       "run autoboot"
-
 /* Miscellaneous configurable options */
 
 /* memtest works on */
@@ -177,24 +144,9 @@
 
 /* **** PISMO SUPPORT *** */
 #if defined(CONFIG_CMD_NAND)
-#define CONFIG_SYS_FLASH_BASE          0x10000000
+#define CFG_SYS_FLASH_BASE             0x10000000
 #endif
 
-#define CONFIG_SYS_MAX_FLASH_SECT      256
-#define CONFIG_SYS_MAX_FLASH_BANKS     1
-#define CONFIG_SYS_FLASH_CFI_WIDTH     FLASH_CFI_16BIT
-#define CONFIG_SYS_FLASH_SIZE          0x4000000
-
-/* Monitor at start of flash */
-#define CONFIG_SYS_MONITOR_BASE                CONFIG_SYS_FLASH_BASE
-
-#define CONFIG_SYS_ENV_SECT_SIZE       (128 << 10)     /* 128 KiB */
-
-/* Defines for SPL */
-
-/* NAND: SPL falcon mode configs */
-#ifdef CONFIG_SPL_OS_BOOT
-#define CONFIG_SYS_NAND_SPL_KERNEL_OFFS        0x280000
-#endif
+#define CFG_SYS_FLASH_SIZE             0x4000000
 
 #endif /* __CONFIG_H */