+++ /dev/null
-/*
- * Common configuration options for ifm camera boards
- *
- * (C) Copyright 2005
- * Sebastien Cazaux, ifm electronic gmbh
- *
- * (C) Copyright 2012
- * DENX Software Engineering, Anatolij Gustschin <agust@denx.de>
- *
- * SPDX-License-Identifier: GPL-2.0+
- */
-
-#ifndef __O2D_CONFIG_H
-#define __O2D_CONFIG_H
-
-/*
- * High Level Configuration Options
- */
-#define CONFIG_MPC5200
-
-#define CONFIG_SYS_MPC5XXX_CLKIN 33000000 /* running at 33.000000MHz */
-
-#define CONFIG_SYS_CACHELINE_SIZE 32 /* For MPC5xxx CPUs */
-#if defined(CONFIG_CMD_KGDB)
-/* log base 2 of the above value */
-#define CONFIG_SYS_CACHELINE_SHIFT 5
-#endif
-
-/*
-#define CONFIG_POST (CONFIG_SYS_POST_MEMORY | \
- CONFIG_SYS_POST_I2C)
-*/
-
-#ifdef CONFIG_POST
-/* preserve space for the post_word at end of on-chip SRAM */
-#define MPC5XXX_SRAM_POST_SIZE (MPC5XXX_SRAM_SIZE - 4)
-#endif
-
-/*
- * Serial console configuration
- */
-#define CONFIG_PSC_CONSOLE 5 /* console is on PSC5 */
-#define CONFIG_BAUDRATE 115200 /* ... at 115200 bps */
-#define CONFIG_SYS_BAUDRATE_TABLE \
- { 9600, 19200, 38400, 57600, 115200, 230400 }
-
-/*
- * PCI Mapping:
- * 0x40000000 - 0x4fffffff - PCI Memory
- * 0x50000000 - 0x50ffffff - PCI IO Space
- */
-
-#define CONFIG_PCI_MEM_BUS 0x40000000
-#define CONFIG_PCI_MEM_PHYS CONFIG_PCI_MEM_BUS
-#define CONFIG_PCI_MEM_SIZE 0x10000000
-
-#define CONFIG_PCI_IO_BUS 0x50000000
-#define CONFIG_PCI_IO_PHYS CONFIG_PCI_IO_BUS
-#define CONFIG_PCI_IO_SIZE 0x01000000
-
-#define CONFIG_SYS_XLB_PIPELINING 1
-
-/* Partitions */
-#define CONFIG_MAC_PARTITION
-#define CONFIG_DOS_PARTITION
-#define CONFIG_ISO_PARTITION
-
-#define CONFIG_TIMESTAMP /* Print image info with timestamp */
-
-#define CONFIG_SYS_ALT_MEMTEST /* Much more complex memory test */
-
-/*
- * Supported commands
- */
-#define CONFIG_CMD_EEPROM
-#ifdef CONFIG_PCI
-#define CONFIG_CMD_PCI
-#endif
-#ifdef CONFIG_POST
-#define CONFIG_CMD_DIAG
-#endif
-
-#if (CONFIG_SYS_TEXT_BASE == 0xFC000000) || (CONFIG_SYS_TEXT_BASE == 0xFF000000)
-/* Boot low with 16 or 32 MB Flash */
-#define CONFIG_SYS_LOWBOOT 1
-#elif (CONFIG_SYS_TEXT_BASE != 0x00100000)
-#error "CONFIG_SYS_TEXT_BASE value is invalid"
-#endif
-
-
-#define CONFIG_PREBOOT "run master"
-
-#undef CONFIG_BOOTARGS
-
-#if !defined(CONSOLE_DEV)
-#define CONSOLE_DEV "ttyPSC1"
-#endif
-
-/*
- * Default environment for booting old and new kernel versions
- */
-#define CONFIG_IFM_DEFAULT_ENV_OLD \
- "flash_self_old=run ramargs addip addmem;" \
- "bootm ${kernel_addr} ${ramdisk_addr}\0" \
- "flash_nfs_old=run nfsargs addip addmem;" \
- "bootm ${kernel_addr}\0" \
- "net_nfs_old=tftp ${kernel_addr_r} ${bootfile};" \
- "run nfsargs addip addmem;" \
- "bootm ${kernel_addr_r}\0"
-
-#define CONFIG_IFM_DEFAULT_ENV_NEW \
- "fdt_addr_r=900000\0" \
- "fdt_file="CONFIG_BOARD_NAME"/"CONFIG_BOARD_NAME".dtb\0" \
- "flash_self=run ramargs addip addtty addmisc;" \
- "bootm ${kernel_addr} ${ramdisk_addr} ${fdt_addr}\0" \
- "flash_nfs=run nfsargs addip addtty addmisc;" \
- "bootm ${kernel_addr} - ${fdt_addr}\0" \
- "net_nfs=tftp ${kernel_addr_r} ${bootfile}; " \
- "tftp ${fdt_addr_r} ${fdt_file}; " \
- "run nfsargs addip addtty addmisc;" \
- "bootm ${kernel_addr_r} - ${fdt_addr_r}\0" \
-
-#define CONFIG_IFM_DEFAULT_ENV_SETTINGS \
- "IOpin=0x64\0" \
- "addip=setenv bootargs ${bootargs} " \
- "ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}" \
- ":${hostname}:${netdev}:off panic=1\0" \
- "addmem=setenv bootargs ${bootargs} ${memlimit}\0" \
- "addmisc=sete bootargs ${bootargs} ${miscargs}\0" \
- "addtty=sete bootargs ${bootargs} console=" \
- CONSOLE_DEV ",${baudrate}\0" \
- "bootfile="CONFIG_BOARD_NAME"/uImage_"CONFIG_BOARD_NAME"_act\0" \
- "kernel_addr_r=600000\0" \
- "initrd_high=0x03e00000\0" \
- "memlimit=mem="CONFIG_BOARD_MEM_LIMIT"M\0" \
- "memtest=mtest 0x00100000 "__stringify(CONFIG_SYS_MEMTEST_END)" 0 1\0" \
- "netdev=eth0\0" \
- "nfsargs=setenv bootargs root=/dev/nfs rw " \
- "nfsroot=${serverip}:${rootpath}\0" \
- "ramargs=setenv bootargs root=/dev/ram rw\0" \
- "linuxname="CONFIG_BOARD_NAME"/uImage_"CONFIG_BOARD_NAME"_act\0"\
- "progLinux=tftp 200000 ${linuxname};erase ${linbot} ${lintop};" \
- "cp.b ${fileaddr} ${linbot} ${filesize}\0" \
- "ramname="CONFIG_BOARD_NAME"/uRamdisk_"CONFIG_BOARD_NAME"_act\0"\
- "progRam=tftp 200000 ${ramname};erase ${rambot} ${ramtop};" \
- "cp.b ${fileaddr} ${rambot} ${filesize}\0" \
- "jffname="CONFIG_BOARD_NAME"/uJFFS2_"CONFIG_BOARD_NAME"_act\0" \
- "progJff=tftp 200000 ${jffname};erase ${jffbot} ${jfftop};" \
- "cp.b ${fileaddr} ${jffbot} ${filesize}\0" \
- "rootpath=/opt/eldk/ppc_6xx\0" \
- "uboname=" CONFIG_BOARD_NAME \
- "/u-boot.bin_" CONFIG_BOARD_NAME "_act\0" \
- "progubo=tftp 200000 ${uboname};" \
- "protect off ${ubobot} ${ubotop};" \
- "erase ${ubobot} ${ubotop};" \
- "cp.b ${fileaddr} ${ubobot} ${filesize}\0" \
- "unlock=yes\0" \
- "post=echo !!! "CONFIG_BOARD_NAME" POWER ON SELF TEST !!!;" \
- "setenv bootdelay 1;" \
- "crc32 "__stringify(CONFIG_SYS_TEXT_BASE)" " \
- BOARD_POST_CRC32_END";" \
- "setenv bootcmd "CONFIG_BOARD_BOOTCMD";saveenv;reset\0"
-
-#define CONFIG_BOOTCOMMAND "run post"
-
-/*
- * IPB Bus clocking configuration.
- */
-#define CONFIG_SYS_IPBCLK_EQUALS_XLBCLK /* define for 133MHz speed */
-
-#if defined(CONFIG_SYS_IPBCLK_EQUALS_XLBCLK)
-/*
- * PCI Bus clocking configuration
- *
- * Actually a PCI Clock of 66 MHz is only set (in cpu_init.c) if
- * CONFIG_SYS_IPBCLK_EQUALS_XLBCLK is defined. This is because a PCI Clock
- * of 66 MHz yet hasn't been tested with a IPB Bus Clock of 66 MHz.
- */
-#define CONFIG_SYS_PCICLK_EQUALS_IPBCLK_DIV2 /* define for 66MHz speed */
-#endif
-
-/*
- * I2C configuration
- */
-#define CONFIG_HARD_I2C 1 /* I2C with hardware support */
-#define CONFIG_SYS_I2C_MODULE 1 /* Select I2C module #1 or #2 */
-#define CONFIG_SYS_I2C_SPEED 100000 /* 100 kHz */
-#define CONFIG_SYS_I2C_SLAVE 0x7F
-
-/*
- * EEPROM configuration:
- *
- * O2DNT board is equiped with Ramtron FRAM device FM24CL16
- * 16 Kib Ferroelectric Nonvolatile serial RAM memory
- * organized as 2048 x 8 bits and addressable as eight I2C devices
- * 0x50 ... 0x57 each 256 bytes in size
- *
- */
-#define CONFIG_SYS_I2C_FRAM
-#define CONFIG_SYS_I2C_EEPROM_ADDR 0x50 /* 1010000x */
-#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1
-#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 3
-/*
- * There is no write delay with FRAM, write operations are performed at bus
- * speed. Thus, no status polling or write delay is needed.
- */
-
-/*
- * Flash configuration
- */
-#define CONFIG_SYS_FLASH_CFI 1
-#define CONFIG_FLASH_CFI_DRIVER 1
-#define CONFIG_FLASH_16BIT
-#define CONFIG_SYS_FLASH_CFI_WIDTH FLASH_CFI_16BIT
-#define CONFIG_SYS_FLASH_CFI_AMD_RESET
-#define CONFIG_SYS_FLASH_EMPTY_INFO
-
-#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* max num of memory banks */
-#define CONFIG_SYS_FLASH_BANKS_LIST { CONFIG_SYS_FLASH_BASE }
-#define CONFIG_SYS_FLASH_ERASE_TOUT 240000 /* Erase Timeout (in ms) */
-#define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Write Timeout (in ms) */
-/* Timeout for Flash Clear Lock Bits (in ms) */
-#define CONFIG_SYS_FLASH_UNLOCK_TOUT 10000
-/* "Real" (hardware) sectors protection */
-#define CONFIG_SYS_FLASH_PROTECTION
-
-/*
- * Environment settings
- */
-#define CONFIG_ENV_IS_IN_FLASH 1
-#define CONFIG_ENV_SIZE 0x20000
-#define CONFIG_ENV_SECT_SIZE 0x20000
-#define CONFIG_ENV_OVERWRITE 1
-#define CONFIG_ENV_ADDR (CONFIG_SYS_FLASH_BASE + 0x00040000)
-
-/*
- * Memory map
- */
-#define CONFIG_SYS_MBAR 0xF0000000
-#define CONFIG_SYS_SDRAM_BASE 0x00000000
-#define CONFIG_SYS_DEFAULT_MBAR 0x80000000
-
-/* Use SRAM until RAM will be available */
-#define CONFIG_SYS_INIT_RAM_ADDR MPC5XXX_SRAM
-#ifdef CONFIG_POST
-/* preserve space for the post_word at end of on-chip SRAM */
-#define CONFIG_SYS_INIT_RAM_SIZE MPC5XXX_SRAM_POST_SIZE
-#else
-/* End of used area in DPRAM */
-#define CONFIG_SYS_INIT_RAM_SIZE MPC5XXX_SRAM_SIZE
-#endif
-
-#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - \
- GENERATED_GBL_DATA_SIZE)
-#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET
-
-#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE
-#define CONFIG_SYS_MONITOR_LEN (192 << 10) /* 192 kB for Monitor */
-#define CONFIG_SYS_MALLOC_LEN (128 << 10) /* 128 kB for malloc() */
-#define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Initial map for Linux */
-
-#if (CONFIG_SYS_MONITOR_BASE < CONFIG_SYS_FLASH_BASE)
-#define CONFIG_SYS_RAMBOOT 1
-#endif
-
-/*
- * Ethernet configuration
- */
-#define CONFIG_MPC5xxx_FEC
-#define CONFIG_MPC5xxx_FEC_MII100
-#define CONFIG_PHY_ADDR 0x00
-#define CONFIG_RESET_PHY_R
-
-/*
- * GPIO configuration
- */
-#define CONFIG_SYS_GPIO_DATADIR 0x00000064 /* PSC1_2, PSC2_1,2 output */
-#define CONFIG_SYS_GPIO_OPENDRAIN 0x00000000 /* No open drain */
-#define CONFIG_SYS_GPIO_DATAVALUE 0x00000000 /* PSC1_1 to 1, rest to 0 */
-#define CONFIG_SYS_GPIO_ENABLE 0x00000064 /* PSC1_2, PSC2_1,2 enable */
-
-/*
- * Miscellaneous configurable options
- */
-#define CONFIG_SYS_LONGHELP /* undef to save memory */
-#define CONFIG_CMDLINE_EDITING
-
-#if defined(CONFIG_CMD_KGDB)
-#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */
-#else
-#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */
-#endif
-/* Print Buffer Size */
-#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + \
- sizeof(CONFIG_SYS_PROMPT) + 16)
-/* max number of command args */
-#define CONFIG_SYS_MAXARGS 16
-/* Boot Argument Buffer Size */
-#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE
-
-/* default load address */
-#define CONFIG_SYS_LOAD_ADDR 0x100000
-
-/* decrementer freq: 1 ms ticks */
-
-/*
- * Various low-level settings
- */
-#define CONFIG_SYS_HID0_INIT HID0_ICE | HID0_ICFI
-#define CONFIG_SYS_HID0_FINAL HID0_ICE
-
-#define CONFIG_SYS_BOOTCS_START CONFIG_SYS_FLASH_BASE
-#define CONFIG_SYS_BOOTCS_SIZE CONFIG_SYS_FLASH_SIZE
-#define CONFIG_SYS_CS0_START CONFIG_SYS_FLASH_BASE
-#define CONFIG_SYS_CS0_SIZE CONFIG_SYS_FLASH_SIZE
-
-#define CONFIG_BOARD_EARLY_INIT_R
-
-#define CONFIG_SYS_CS_BURST 0x00000000
-#define CONFIG_SYS_CS_DEADCYCLE 0x33333333
-
-/*
- * DT support
- */
-#define OF_CPU "PowerPC,5200@0"
-#define OF_SOC "soc5200@f0000000"
-#define OF_TBCLK (bd->bi_busfreq / 4)
-
-#endif /* __O2D_CONFIG_H */
projects / platform / kernel / u-boot.git / blobdiff