Prepare v2023.10

[platform/kernel/u-boot.git] / include / configs / mx6qsabreauto.h

diff --git a/include/configs/mx6qsabreauto.h b/include/configs/mx6qsabreauto.h
deleted file mode 100644 (file)
index 51042ca..0000000
--- a/include/configs/mx6qsabreauto.h
+++ /dev/null
@@ -1,83 +0,0 @@
-/*
- * Copyright (C) 2012 Freescale Semiconductor, Inc.
- *
- * Configuration settings for the Freescale i.MX6Q SabreAuto board.
- *
- * SPDX-License-Identifier:    GPL-2.0+
- */
-
-#ifndef __MX6QSABREAUTO_CONFIG_H
-#define __MX6QSABREAUTO_CONFIG_H
-
-#define CONFIG_MACH_TYPE       3529
-#define CONFIG_MXC_UART_BASE   UART4_BASE
-#define CONFIG_CONSOLE_DEV             "ttymxc3"
-#if defined CONFIG_MX6Q
-#define CONFIG_DEFAULT_FDT_FILE        "imx6q-sabreauto.dtb"
-#elif defined CONFIG_MX6DL
-#define CONFIG_DEFAULT_FDT_FILE        "imx6dl-sabreauto.dtb"
-#endif
-#define CONFIG_MMCROOT                 "/dev/mmcblk0p2"
-#define PHYS_SDRAM_SIZE                (2u * 1024 * 1024 * 1024)
-
-/* USB Configs */
-#define CONFIG_CMD_USB
-#define CONFIG_USB_EHCI
-#define CONFIG_USB_EHCI_MX6
-#define CONFIG_USB_STORAGE
-#define CONFIG_USB_HOST_ETHER
-#define CONFIG_USB_ETHER_ASIX
-#define CONFIG_USB_MAX_CONTROLLER_COUNT 2
-#define CONFIG_EHCI_HCD_INIT_AFTER_RESET       /* For OTG port */
-#define CONFIG_MXC_USB_PORTSC  (PORT_PTS_UTMI | PORT_PTS_PTW)
-#define CONFIG_MXC_USB_FLAGS   0
-
-#define CONFIG_PCA953X
-#define CONFIG_SYS_I2C_PCA953X_WIDTH   { {0x30, 8}, {0x32, 8}, {0x34, 8} }
-
-#include "mx6sabre_common.h"
-
-#undef CONFIG_SYS_NO_FLASH
-#define CONFIG_SYS_FLASH_BASE           WEIM_ARB_BASE_ADDR
-#define CONFIG_SYS_FLASH_SECT_SIZE      (128 * 1024)
-#define CONFIG_SYS_MAX_FLASH_BANKS 1    /* max number of memory banks */
-#define CONFIG_SYS_MAX_FLASH_SECT 256   /* max number of sectors on one chip */
-#define CONFIG_SYS_FLASH_CFI            /* Flash memory is CFI compliant */
-#define CONFIG_FLASH_CFI_DRIVER         /* Use drivers/cfi_flash.c */
-#define CONFIG_SYS_FLASH_USE_BUFFER_WRITE /* Use buffered writes*/
-#define CONFIG_SYS_FLASH_EMPTY_INFO
-
-#define CONFIG_SYS_FSL_USDHC_NUM       2
-#if defined(CONFIG_ENV_IS_IN_MMC)
-#define CONFIG_SYS_MMC_ENV_DEV         0
-#endif
-
-/* I2C Configs */
-#define CONFIG_CMD_I2C
-#define CONFIG_SYS_I2C
-#define CONFIG_SYS_I2C_MXC
-#define CONFIG_SYS_I2C_SPEED           100000
-
-/* NAND flash command */
-#define CONFIG_CMD_NAND
-#define CONFIG_CMD_NAND_TRIMFFS
-
-/* NAND stuff */
-#define CONFIG_NAND_MXS
-#define CONFIG_SYS_MAX_NAND_DEVICE     1
-#define CONFIG_SYS_NAND_BASE           0x40000000
-#define CONFIG_SYS_NAND_5_ADDR_CYCLE
-#define CONFIG_SYS_NAND_ONFI_DETECTION
-
-/* DMA stuff, needed for GPMI/MXS NAND support */
-#define CONFIG_APBH_DMA
-#define CONFIG_APBH_DMA_BURST
-#define CONFIG_APBH_DMA_BURST8
-
-/* PMIC */
-#define CONFIG_POWER
-#define CONFIG_POWER_I2C
-#define CONFIG_POWER_PFUZE100
-#define CONFIG_POWER_PFUZE100_I2C_ADDR 0x08
-
-#endif                         /* __MX6QSABREAUTO_CONFIG_H */