Migrate CUSTOM_SYS_INIT_SP_ADDR to Kconfig using system-constants.h

[platform/kernel/u-boot.git] / include / configs / lx2160a_common.h

diff --git a/include/configs/lx2160a_common.h b/include/configs/lx2160a_common.h
index 7173fe6..5609668 100644 (file)
--- a/include/configs/lx2160a_common.h
+++ b/include/configs/lx2160a_common.h
@@ -10,15 +10,11 @@
 #include <asm/arch/config.h>
 #include <asm/arch/soc.h>
 
-#define CONFIG_REMAKE_ELF
-#define CONFIG_FSL_TZPC_BP147
 #define CONFIG_FSL_MEMAC
 
-#define CONFIG_SYS_INIT_SP_ADDR                CONFIG_SYS_TEXT_BASE
 #define CONFIG_SYS_FLASH_BASE          0x20000000
 
 /* DDR */
-#define CONFIG_FSL_DDR_INTERACTIVE     /* Interactive debugging */
 #define CONFIG_SYS_FSL_DDR_INTLV_256B  /* force 256 byte interleaving */
 #define CONFIG_VERY_BIG_RAM
 #define CONFIG_SYS_DDR_SDRAM_BASE              0x80000000UL
@@ -36,9 +32,6 @@
 #define SPD_EEPROM_ADDRESS6            0x56
 #define SPD_EEPROM_ADDRESS             SPD_EEPROM_ADDRESS1
 #define CONFIG_SYS_SPD_BUS_NUM         0       /* SPD on I2C bus 0 */
-#define CONFIG_DIMM_SLOTS_PER_CTLR     2
-#define CONFIG_CHIP_SELECTS_PER_CTRL   4
-#define CONFIG_FSL_DDR_BIST    /* enable built-in memory test */
 #define CONFIG_SYS_MONITOR_LEN         (936 * 1024)
 
 /* Miscellaneous configurable options */
@@ -52,7 +45,6 @@
  * will be udpated later when get_bus_freq(0) is available.
  */
 
-#define COUNTER_FREQUENCY              25000000        /* 25MHz */
 
 /* Serial Port */
 #define CONFIG_PL011_CLOCK             (get_bus_freq(0) / 4)
@@ -73,11 +65,6 @@
 #define CONFIG_SYS_LS_MC_DRAM_DPL_OFFSET       0x00F20000
 #define CONFIG_SYS_LS_MC_BOOT_TIMEOUT_MS       5000
 
-/* Define phy_reset function to boot the MC based on mcinitcmd.
- * This happens late enough to properly fixup u-boot env MAC addresses.
- */
-#define CONFIG_RESET_PHY_R
-
 /*
  * Carve out a DDR region which will not be used by u-boot/Linux
  *
@@ -101,26 +88,18 @@
 #define CONFIG_SYS_EEPROM_BUS_NUM              0
 
 /* Qixis */
-#define CONFIG_FSL_QIXIS
-#define CONFIG_QIXIS_I2C_ACCESS
 #define CONFIG_SYS_I2C_FPGA_ADDR               0x66
 
 /* PCI */
 #ifdef CONFIG_PCI
-#define CONFIG_SYS_PCI_64BIT
 #define CONFIG_PCI_SCAN_SHOW
 #endif
 
 /* SATA */
 
 #ifdef CONFIG_SCSI
-#define CONFIG_SCSI_AHCI_PLAT
 #define CONFIG_SYS_SATA1               AHCI_BASE_ADDR1
 #define CONFIG_SYS_SATA2               AHCI_BASE_ADDR2
-#define CONFIG_SYS_SCSI_MAX_SCSI_ID    1
-#define CONFIG_SYS_SCSI_MAX_LUN                1
-#define CONFIG_SYS_SCSI_MAX_DEVICE     (CONFIG_SYS_SCSI_MAX_SCSI_ID * \
-                                       CONFIG_SYS_SCSI_MAX_LUN)
 #endif
 
 /* USB */
@@ -130,30 +109,11 @@
 #endif
 #endif
 
-/* GPIO */
-#ifdef CONFIG_DM_GPIO
-#ifndef CONFIG_MPC8XXX_GPIO
-#define CONFIG_MPC8XXX_GPIO
-#endif
-#endif
-
-#ifndef __ASSEMBLY__
-unsigned long get_board_sys_clk(void);
-#endif
-
-#define CONFIG_SYS_CLK_FREQ            get_board_sys_clk()
-#define COUNTER_FREQUENCY_REAL         (CONFIG_SYS_CLK_FREQ / 4)
+#define COUNTER_FREQUENCY_REAL         (get_board_sys_clk() / 4)
 
 #define CONFIG_HWCONFIG
 #define HWCONFIG_BUFFER_SIZE           128
 
-/* Monitor Command Prompt */
-#define CONFIG_SYS_CBSIZE              512     /* Console I/O Buffer Size */
-#define CONFIG_SYS_PBSIZE              (CONFIG_SYS_CBSIZE + \
-                                       sizeof(CONFIG_SYS_PROMPT) + 16)
-#define CONFIG_SYS_BARGSIZE            CONFIG_SYS_CBSIZE /* Boot args buffer */
-#define CONFIG_SYS_MAXARGS             64      /* max command args */
-
 #define CONFIG_SYS_BOOTM_LEN   (64 << 20)      /* Increase max gunzip size */
 
 /* Initial environment variables */
@@ -196,7 +156,6 @@ unsigned long get_board_sys_clk(void);
        "ramdisk_size=0x2000000\0"              \
        "fdt_high=0xa0000000\0"                 \
        "initrd_high=0xffffffffffffffff\0"      \
-       "fdt_addr=0x64f00000\0"                 \
        "kernel_start=0x1000000\0"              \
        "kernelheader_start=0x600000\0"         \
        "scriptaddr=0x80000000\0"               \
@@ -266,12 +225,36 @@ unsigned long get_board_sys_clk(void);
                "run distro_bootcmd;run sd2_bootcmd;"           \
                "env exists secureboot && esbc_halt;"
 
+#ifdef CONFIG_CMD_USB
+#define BOOT_TARGET_DEVICES_USB(func) func(USB, usb, 0)
+#else
+#define BOOT_TARGET_DEVICES_USB(func)
+#endif
+
+#ifdef CONFIG_MMC
+#define BOOT_TARGET_DEVICES_MMC(func, instance) func(MMC, mmc, instance)
+#else
+#define BOOT_TARGET_DEVICES_MMC(func)
+#endif
+
+#ifdef CONFIG_SCSI
+#define BOOT_TARGET_DEVICES_SCSI(func) func(SCSI, scsi, 0)
+#else
+#define BOOT_TARGET_DEVICES_SCSI(func)
+#endif
+
+#ifdef CONFIG_CMD_DHCP
+#define BOOT_TARGET_DEVICES_DHCP(func) func(DHCP, dhcp, na)
+#else
+#define BOOT_TARGET_DEVICES_DHCP(func)
+#endif
+
 #define BOOT_TARGET_DEVICES(func) \
-       func(USB, usb, 0) \
-       func(MMC, mmc, 0) \
-       func(MMC, mmc, 1) \
-       func(SCSI, scsi, 0) \
-       func(DHCP, dhcp, na)
+       BOOT_TARGET_DEVICES_USB(func) \
+       BOOT_TARGET_DEVICES_MMC(func, 0) \
+       BOOT_TARGET_DEVICES_MMC(func, 1) \
+       BOOT_TARGET_DEVICES_SCSI(func) \
+       BOOT_TARGET_DEVICES_DHCP(func)
 #include <config_distro_bootcmd.h>
 
 #endif /* __LX2_COMMON_H */