Replace "run load; run update" with conditionalized "run load update".

[platform/kernel/u-boot.git] / include / configs / luan.h

diff --git a/include/configs/luan.h b/include/configs/luan.h
index cbb59c5..af237d9 100644 (file)
--- a/include/configs/luan.h
+++ b/include/configs/luan.h
@@ -39,7 +39,6 @@
 
 #define CONFIG_BOARD_EARLY_INIT_F 1    /* call board_early_init_f()    */
 #define CONFIG_MISC_INIT_R     1       /* call misc_init_r()           */
-#define CONFIG_ADD_RAM_INFO    1       /* Print additional info        */
 
 /*-----------------------------------------------------------------------
  * Base addresses -- Note these are effective addresses where the
@@ -136,7 +135,6 @@
 #define CONFIG_SPD_EEPROM      1       /* Use SPD EEPROM for setup     */
 #define SPD_EEPROM_ADDRESS     {0x53, 0x52}    /* SPD i2c spd addresses*/
 #define CONFIG_DDR_ECC         1       /* with ECC support             */
-#define CFG_44x_DDR2_CKTR_180  1       /* use 180 deg advance          */
 
 /*-----------------------------------------------------------------------
  * I2C
@@ -154,7 +152,7 @@
 #define CFG_EEPROM_PAGE_WRITE_DELAY_MS 10
 
 #define CONFIG_PREBOOT "echo;" \
-       "echo Type \"run flash_nfs\" to mount root filesystem over NFS;" \
+       "echo Type \\\"run flash_nfs\\\" to mount root filesystem over NFS;" \
        "echo"
 
 #undef CONFIG_BOOTARGS
@@ -184,7 +182,7 @@
        "update=protect off fffc0000 ffffffff;era fffc0000 ffffffff;"   \
                "cp.b 100000 fffc0000 40000;"                           \
                "setenv filesize;saveenv\0"                             \
-       "upd=run load;run update\0"                                     \
+       "upd=run load update\0"                                         \
        ""
 #define CONFIG_BOOTCOMMAND     "run flash_self"
 
@@ -213,31 +211,38 @@
 #define CONFIG_HW_WATCHDOG                     /* watchdog */
 #endif
 
-#define CONFIG_COMMANDS               (CONFIG_CMD_DFL          |       \
-                               CFG_CMD_ASKENV          |       \
-                               CFG_CMD_DHCP            |       \
-                               CFG_CMD_ELF             |       \
-                               CFG_CMD_EEPROM          |       \
-                               CFG_CMD_I2C             |       \
-                               CFG_CMD_IRQ             |       \
-                               CFG_CMD_MII             |       \
-                               CFG_CMD_NET             |       \
-                               CFG_CMD_NFS             |       \
-                               CFG_CMD_PCI             |       \
-                               CFG_CMD_PING            |       \
-                               CFG_CMD_REGINFO         |       \
-                               CFG_CMD_SDRAM           |       \
-                               0)
-
-/* this must be included AFTER the definition of CONFIG_COMMANDS */
-#include <cmd_confdefs.h>
+/*
+ * BOOTP options
+ */
+#define CONFIG_BOOTP_BOOTFILESIZE
+#define CONFIG_BOOTP_BOOTPATH
+#define CONFIG_BOOTP_GATEWAY
+#define CONFIG_BOOTP_HOSTNAME
+
+/*
+ * Command line configuration.
+ */
+#include <config_cmd_default.h>
+
+#define CONFIG_CMD_ASKENV
+#define CONFIG_CMD_DHCP
+#define CONFIG_CMD_EEPROM
+#define CONFIG_CMD_I2C
+#define CONFIG_CMD_IRQ
+#define CONFIG_CMD_MII
+#define CONFIG_CMD_NET
+#define CONFIG_CMD_NFS
+#define CONFIG_CMD_PCI
+#define CONFIG_CMD_PING
+#define CONFIG_CMD_REGINFO
+#define CONFIG_CMD_SDRAM
 
 /*
  * Miscellaneous configurable options
  */
 #define CFG_LONGHELP                   /* undef to save memory         */
 #define CFG_PROMPT             "=> "   /* Monitor Command Prompt       */
-#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
+#if defined(CONFIG_CMD_KGDB)
 #define CFG_CBSIZE             1024    /* Console I/O Buffer Size      */
 #else
 #define CFG_CBSIZE             256     /* Console I/O Buffer Size      */
@@ -265,7 +270,7 @@
  * PCI stuff
  *-----------------------------------------------------------------------
  */
-#if (CONFIG_COMMANDS & CFG_CMD_PCI)
+#if defined(CONFIG_CMD_PCI)
 
 /* General PCI */
 #define CONFIG_PCI                     /* include pci support          */
@@ -279,7 +284,7 @@
 #define CFG_PCI_SUBSYS_VENDORID 0x10e8 /* AMCC */
 #define CFG_PCI_SUBSYS_DEVICEID 0x4403 /* whatever */
 
-#endif /* CONFIG_COMMANDS & CFG_CMD_PCI */
+#endif
 
 /*
  * For booting Linux, the board info and command line data
@@ -288,15 +293,6 @@
  */
 #define CFG_BOOTMAPSZ          (8 << 20)       /* Initial Memory map for Linux */
 
-/*-----------------------------------------------------------------------
- * Cache Configuration
- */
-#define CFG_DCACHE_SIZE                (32<<10) /* For AMCC 440 CPUs                   */
-#define CFG_CACHELINE_SIZE     32      /* ...                  */
-#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
-#define CFG_CACHELINE_SHIFT    5       /* log base 2 of the above value        */
-#endif
-
 /*
  * Internal Definitions
  *
@@ -305,7 +301,7 @@
 #define BOOTFLAG_COLD  0x01            /* Normal Power-On: Boot from FLASH     */
 #define BOOTFLAG_WARM  0x02            /* Software reboot                      */
 
-#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
+#if defined(CONFIG_CMD_KGDB)
 #define CONFIG_KGDB_BAUDRATE   230400  /* speed to run kgdb serial port */
 #define CONFIG_KGDB_SER_INDEX  2       /* which serial port to use */
 #endif