+++ /dev/null
-/*
- * Copyright (C) 2014 Freescale Semiconductor
- *
- * SPDX-License-Identifier: GPL-2.0+
- */
-
-#ifndef __LS2_COMMON_H
-#define __LS2_COMMON_H
-
-#define CONFIG_SYS_GENERIC_BOARD
-
-#define CONFIG_REMAKE_ELF
-#define CONFIG_FSL_LSCH3
-#define CONFIG_LS2085A
-#define CONFIG_GICV3
-#define CONFIG_FSL_TZPC_BP147
-
-/* Link Definitions */
-#define CONFIG_SYS_TEXT_BASE 0x30001000
-
-#ifdef CONFIG_EMU
-#define CONFIG_SYS_NO_FLASH
-#endif
-
-#define CONFIG_SUPPORT_RAW_INITRD
-
-#define CONFIG_SKIP_LOWLEVEL_INIT
-#define CONFIG_BOARD_EARLY_INIT_F 1
-
-/* Flat Device Tree Definitions */
-#define CONFIG_OF_LIBFDT
-#define CONFIG_OF_BOARD_SETUP
-
-/* new uImage format support */
-#define CONFIG_FIT
-#define CONFIG_FIT_VERBOSE /* enable fit_format_{error,warning}() */
-
-#define CONFIG_FSL_DDR_INTERACTIVE /* Interactive debugging */
-#ifndef CONFIG_SYS_FSL_DDR4
-#define CONFIG_SYS_FSL_DDR3 /* Use DDR3 memory */
-#define CONFIG_SYS_DDR_RAW_TIMING
-#endif
-#define CONFIG_DIMM_SLOTS_PER_CTLR 1
-#define CONFIG_CHIP_SELECTS_PER_CTRL 4
-
-#define CONFIG_SYS_FSL_DDR_INTLV_256B /* force 256 byte interleaving */
-
-#define CONFIG_SYS_DDR_SDRAM_BASE 0x80000000UL
-#define CONFIG_SYS_FSL_DDR_SDRAM_BASE_PHY 0
-#define CONFIG_SYS_SDRAM_BASE CONFIG_SYS_DDR_SDRAM_BASE
-#define CONFIG_SYS_DDR_BLOCK2_BASE 0x8080000000ULL
-#define CONFIG_SYS_FSL_DDR_MAIN_NUM_CTRLS 2
-
-/*
- * SMP Definitinos
- */
-#define CPU_RELEASE_ADDR secondary_boot_func
-
-#define CONFIG_SYS_FSL_OTHER_DDR_NUM_CTRLS
-#define CONFIG_SYS_DP_DDR_BASE 0x6000000000ULL
-/*
- * DDR controller use 0 as the base address for binding.
- * It is mapped to CONFIG_SYS_DP_DDR_BASE for core to access.
- */
-#define CONFIG_SYS_DP_DDR_BASE_PHY 0
-#define CONFIG_DP_DDR_CTRL 2
-#define CONFIG_DP_DDR_NUM_CTRLS 1
-#define CONFIG_DP_DDR_DIMM_SLOTS_PER_CTLR 1
-
-/* Generic Timer Definitions */
-#define COUNTER_FREQUENCY 12000000 /* 12MHz */
-
-/* Size of malloc() pool */
-#define CONFIG_SYS_MALLOC_LEN (CONFIG_ENV_SIZE + 128 * 1024)
-
-/* I2C */
-#define CONFIG_CMD_I2C
-#define CONFIG_SYS_I2C
-#define CONFIG_SYS_I2C_MXC
-#define CONFIG_SYS_MXC_I2C1_SPEED 40000000
-#define CONFIG_SYS_MXC_I2C2_SPEED 40000000
-
-/* Serial Port */
-#define CONFIG_CONS_INDEX 2
-#define CONFIG_SYS_NS16550
-#define CONFIG_SYS_NS16550_SERIAL
-#define CONFIG_SYS_NS16550_REG_SIZE 1
-#define CONFIG_SYS_NS16550_CLK (get_bus_freq(0)/2)
-
-#define CONFIG_BAUDRATE 115200
-#define CONFIG_SYS_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200 }
-
-/* IFC */
-#define CONFIG_FSL_IFC
-#define CONFIG_SYS_NOR0_CSPR_EXT (0x0)
-#define CONFIG_SYS_NOR_AMASK IFC_AMASK(128*1024*1024)
-/*
- * During booting, CS0 needs to be at the region of 0x30000000, i.e. the IFC
- * address 0. But this region is limited to 256MB. To accommodate bigger NOR
- * flash and other devices, we will map CS0 to 0x580000000 after relocation.
- * CONFIG_SYS_FLASH_BASE has the final address (core view)
- * CONFIG_SYS_FLASH_BASE_PHYS has the final address (IFC view)
- * CONFIG_SYS_FLASH_BASE_PHYS_EARLY has the temporary IFC address
- * CONFIG_SYS_TEXT_BASE is linked to 0x30000000 for booting
- */
-#define CONFIG_SYS_FLASH_BASE 0x580000000ULL
-#define CONFIG_SYS_FLASH_BASE_PHYS 0x80000000
-#define CONFIG_SYS_FLASH_BASE_PHYS_EARLY 0x00000000
-
-/*
- * NOR Flash Timing Params
- */
-#define CONFIG_SYS_NOR0_CSPR \
- (CSPR_PHYS_ADDR(CONFIG_SYS_FLASH_BASE_PHYS) | \
- CSPR_PORT_SIZE_16 | \
- CSPR_MSEL_NOR | \
- CSPR_V)
-#define CONFIG_SYS_NOR0_CSPR_EARLY \
- (CSPR_PHYS_ADDR(CONFIG_SYS_FLASH_BASE_PHYS_EARLY) | \
- CSPR_PORT_SIZE_16 | \
- CSPR_MSEL_NOR | \
- CSPR_V)
-#define CONFIG_SYS_NOR_CSOR CSOR_NOR_ADM_SHIFT(12)
-#define CONFIG_SYS_NOR_FTIM0 (FTIM0_NOR_TACSE(0x1) | \
- FTIM0_NOR_TEADC(0x1) | \
- FTIM0_NOR_TEAHC(0x1))
-#define CONFIG_SYS_NOR_FTIM1 (FTIM1_NOR_TACO(0x1) | \
- FTIM1_NOR_TRAD_NOR(0x1))
-#define CONFIG_SYS_NOR_FTIM2 (FTIM2_NOR_TCS(0x0) | \
- FTIM2_NOR_TCH(0x0) | \
- FTIM2_NOR_TWP(0x1))
-#define CONFIG_SYS_NOR_FTIM3 0x04000000
-#define CONFIG_SYS_IFC_CCR 0x01000000
-
-#ifndef CONFIG_SYS_NO_FLASH
-#define CONFIG_FLASH_CFI_DRIVER
-#define CONFIG_SYS_FLASH_CFI
-#define CONFIG_SYS_FLASH_USE_BUFFER_WRITE
-#define CONFIG_SYS_FLASH_QUIET_TEST
-#define CONFIG_FLASH_SHOW_PROGRESS 45 /* count down from 45/5: 9..1 */
-
-#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* number of banks */
-#define CONFIG_SYS_MAX_FLASH_SECT 1024 /* sectors per device */
-#define CONFIG_SYS_FLASH_ERASE_TOUT 60000 /* Flash Erase Timeout (ms) */
-#define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (ms) */
-
-#define CONFIG_SYS_FLASH_EMPTY_INFO
-#define CONFIG_SYS_FLASH_BANKS_LIST { CONFIG_SYS_FLASH_BASE }
-#endif
-
-#define CONFIG_NAND_FSL_IFC
-#define CONFIG_SYS_NAND_MAX_ECCPOS 256
-#define CONFIG_SYS_NAND_MAX_OOBFREE 2
-#define CONFIG_SYS_NAND_BASE 0x520000000
-#define CONFIG_SYS_NAND_BASE_PHYS 0x20000000
-
-#define CONFIG_SYS_NAND_CSPR_EXT (0x0)
-#define CONFIG_SYS_NAND_CSPR (CSPR_PHYS_ADDR(CONFIG_SYS_NAND_BASE_PHYS) \
- | CSPR_PORT_SIZE_8 /* Port Size = 8 bit */ \
- | CSPR_MSEL_NAND /* MSEL = NAND */ \
- | CSPR_V)
-#define CONFIG_SYS_NAND_AMASK IFC_AMASK(64 * 1024)
-
-#define CONFIG_SYS_NAND_CSOR (CSOR_NAND_ECC_ENC_EN /* ECC on encode */ \
- | CSOR_NAND_ECC_DEC_EN /* ECC on decode */ \
- | CSOR_NAND_ECC_MODE_4 /* 4-bit ECC */ \
- | CSOR_NAND_RAL_3 /* RAL = 2Byes */ \
- | CSOR_NAND_PGS_2K /* Page Size = 2K */ \
- | CSOR_NAND_SPRZ_64/* Spare size = 64 */ \
- | CSOR_NAND_PB(64)) /*Pages Per Block = 64*/
-
-#define CONFIG_SYS_NAND_ONFI_DETECTION
-
-/* ONFI NAND Flash mode0 Timing Params */
-#define CONFIG_SYS_NAND_FTIM0 (FTIM0_NAND_TCCST(0x07) | \
- FTIM0_NAND_TWP(0x18) | \
- FTIM0_NAND_TWCHT(0x07) | \
- FTIM0_NAND_TWH(0x0a))
-#define CONFIG_SYS_NAND_FTIM1 (FTIM1_NAND_TADLE(0x32) | \
- FTIM1_NAND_TWBE(0x39) | \
- FTIM1_NAND_TRR(0x0e) | \
- FTIM1_NAND_TRP(0x18))
-#define CONFIG_SYS_NAND_FTIM2 (FTIM2_NAND_TRAD(0x0f) | \
- FTIM2_NAND_TREH(0x0a) | \
- FTIM2_NAND_TWHRE(0x1e))
-#define CONFIG_SYS_NAND_FTIM3 0x0
-
-#define CONFIG_SYS_NAND_BASE_LIST { CONFIG_SYS_NAND_BASE }
-#define CONFIG_SYS_MAX_NAND_DEVICE 1
-#define CONFIG_MTD_NAND_VERIFY_WRITE
-#define CONFIG_CMD_NAND
-
-#define CONFIG_SYS_NAND_BLOCK_SIZE (128 * 1024)
-
-#define CONFIG_SYS_CSPR0_EXT CONFIG_SYS_NOR0_CSPR_EXT
-#define CONFIG_SYS_CSPR0 CONFIG_SYS_NOR0_CSPR_EARLY
-#define CONFIG_SYS_CSPR0_FINAL CONFIG_SYS_NOR0_CSPR
-#define CONFIG_SYS_AMASK0 CONFIG_SYS_NOR_AMASK
-#define CONFIG_SYS_CSOR0 CONFIG_SYS_NOR_CSOR
-#define CONFIG_SYS_CS0_FTIM0 CONFIG_SYS_NOR_FTIM0
-#define CONFIG_SYS_CS0_FTIM1 CONFIG_SYS_NOR_FTIM1
-#define CONFIG_SYS_CS0_FTIM2 CONFIG_SYS_NOR_FTIM2
-#define CONFIG_SYS_CS0_FTIM3 CONFIG_SYS_NOR_FTIM3
-
-/* MC firmware */
-#define CONFIG_FSL_MC_ENET
-#define CONFIG_SYS_LS_MC_DRAM_BLOCK_MIN_SIZE (512UL * 1024 * 1024)
-#define CONFIG_SYS_LS_MC_FW_IN_NOR
-#define CONFIG_SYS_LS_MC_FW_ADDR 0x580200000ULL
-/* TODO Actual FW length needs to be determined at runtime from FW header */
-#define CONFIG_SYS_LS_MC_FW_LENGTH (4U * 1024 * 1024)
-#define CONFIG_SYS_LS_MC_DPL_IN_NOR
-#define CONFIG_SYS_LS_MC_DPL_ADDR 0x5806C0000ULL
-/* TODO Actual DPL max length needs to be confirmed with the MC FW team */
-#define CONFIG_SYS_LS_MC_DPL_LENGTH 4096
-#define CONFIG_SYS_LS_MC_DRAM_DPL_OFFSET 0xe00000
-
-/* Carve the MC private DRAM block from the end of DRAM */
-#ifdef CONFIG_FSL_MC_ENET
-#define CONFIG_SYS_MEM_TOP_HIDE mc_get_dram_block_size()
-#endif
-
-/* Command line configuration */
-#define CONFIG_CMD_CACHE
-#define CONFIG_CMD_BDI
-#define CONFIG_CMD_DHCP
-#define CONFIG_CMD_ENV
-#define CONFIG_CMD_FLASH
-#define CONFIG_CMD_IMI
-#define CONFIG_CMD_MEMORY
-#define CONFIG_CMD_MII
-#define CONFIG_CMD_NET
-#define CONFIG_CMD_PING
-#define CONFIG_CMD_SAVEENV
-#define CONFIG_CMD_RUN
-#define CONFIG_CMD_BOOTD
-#define CONFIG_CMD_ECHO
-#define CONFIG_CMD_SOURCE
-#define CONFIG_CMD_FAT
-#define CONFIG_DOS_PARTITION
-
-/* Miscellaneous configurable options */
-#define CONFIG_SYS_LOAD_ADDR (CONFIG_SYS_DDR_SDRAM_BASE + 0x10000000)
-#define CONFIG_ARCH_EARLY_INIT_R
-
-/* Physical Memory Map */
-/* fixme: these need to be checked against the board */
-#define CONFIG_CHIP_SELECTS_PER_CTRL 4
-#define CONFIG_SYS_CLK_FREQ 100000000
-#define CONFIG_DDR_CLK_FREQ 133333333
-
-
-#define CONFIG_NR_DRAM_BANKS 3
-
-#define CONFIG_HWCONFIG
-#define HWCONFIG_BUFFER_SIZE 128
-
-#define CONFIG_DISPLAY_CPUINFO
-
-/* Initial environment variables */
-#define CONFIG_EXTRA_ENV_SETTINGS \
- "hwconfig=fsl_ddr:bank_intlv=auto\0" \
- "loadaddr=0x80100000\0" \
- "kernel_addr=0x100000\0" \
- "ramdisk_addr=0x800000\0" \
- "ramdisk_size=0x2000000\0" \
- "fdt_high=0xffffffffffffffff\0" \
- "initrd_high=0xffffffffffffffff\0" \
- "kernel_start=0x581200000\0" \
- "kernel_load=0xa0000000\0" \
- "kernel_size=0x1000000\0" \
- "console=ttyAMA0,38400n8\0"
-
-#define CONFIG_BOOTARGS "console=ttyS1,115200 root=/dev/ram0 " \
- "earlycon=uart8250,mmio,0x21c0600,115200 " \
- "default_hugepagesz=2m hugepagesz=2m " \
- "hugepages=16"
-#define CONFIG_BOOTCOMMAND "cp.b $kernel_start $kernel_load " \
- "$kernel_size && bootm $kernel_load"
-#define CONFIG_BOOTDELAY 1
-
-/* Store environment at top of flash */
-#define CONFIG_ENV_IS_NOWHERE 1
-#define CONFIG_ENV_SIZE 0x1000
-
-/* Monitor Command Prompt */
-#define CONFIG_SYS_CBSIZE 512 /* Console I/O Buffer Size */
-#define CONFIG_SYS_PROMPT "> "
-#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + \
- sizeof(CONFIG_SYS_PROMPT) + 16)
-#define CONFIG_SYS_HUSH_PARSER
-#define CONFIG_SYS_PROMPT_HUSH_PS2 "> "
-#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot args buffer */
-#define CONFIG_SYS_LONGHELP
-#define CONFIG_CMDLINE_EDITING 1
-#define CONFIG_SYS_MAXARGS 64 /* max command args */
-
-#ifndef __ASSEMBLY__
-unsigned long mc_get_dram_block_size(void);
-#endif
-
-#endif /* __LS2_COMMON_H */
projects / platform / kernel / u-boot.git / blobdiff