+++ /dev/null
-/*
- * (C) Copyright 2007
- * Heiko Schocher, DENX Software Engineering, hs@denx.de.
- *
- * SPDX-License-Identifier: GPL-2.0+
- */
-
-#ifndef __CONFIG_H
-#define __CONFIG_H
-
-/*
- * High Level Configuration Options
- * (easy to change)
- */
-
-#define CONFIG_MPC5xxx 1 /* This is an MPC5xxx CPU */
-#define CONFIG_MPC5200 1 /* especially an MPC5200 */
-#define CONFIG_JUPITER 1 /* ... on Jupiter board */
-
-/*
- * Valid values for CONFIG_SYS_TEXT_BASE are:
- * 0xFFF00000 boot high (standard configuration)
- * 0x00100000 boot from RAM (for testing only)
- */
-#ifndef CONFIG_SYS_TEXT_BASE
-#define CONFIG_SYS_TEXT_BASE 0xFFF00000
-#endif
-
-#define CONFIG_SYS_MPC5XXX_CLKIN 33000000 /* ... running at 33.000000MHz */
-
-#define CONFIG_BOARD_EARLY_INIT_R 1
-#define CONFIG_BOARD_EARLY_INIT_F 1
-
-#define CONFIG_HIGH_BATS 1 /* High BATs supported */
-
-/*
- * Serial console configuration
- */
-#define CONFIG_PSC_CONSOLE 1 /* console is on PSC1 */
-#define CONFIG_BAUDRATE 115200 /* ... at 115200 bps */
-#define CONFIG_SYS_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200, 230400 }
-
-/*
- * PCI Mapping:
- * 0x40000000 - 0x4fffffff - PCI Memory
- * 0x50000000 - 0x50ffffff - PCI IO Space
- */
-/*#define CONFIG_PCI */
-
-#if defined(CONFIG_PCI)
-#define CONFIG_PCI_PNP 1
-#define CONFIG_PCI_SCAN_SHOW 1
-#define CONFIG_PCIAUTO_SKIP_HOST_BRIDGE 1
-
-#define CONFIG_PCI_MEM_BUS 0x40000000
-#define CONFIG_PCI_MEM_PHYS CONFIG_PCI_MEM_BUS
-#define CONFIG_PCI_MEM_SIZE 0x10000000
-
-#define CONFIG_PCI_IO_BUS 0x50000000
-#define CONFIG_PCI_IO_PHYS CONFIG_PCI_IO_BUS
-#define CONFIG_PCI_IO_SIZE 0x01000000
-#endif
-
-#define CONFIG_SYS_XLB_PIPELINING 1
-
-#define CONFIG_MII 1
-#define CONFIG_SYS_RX_ETH_BUFFER 8 /* use 8 rx buffer on eepro100 */
-
-/* Partitions */
-#define CONFIG_MAC_PARTITION
-#define CONFIG_DOS_PARTITION
-#define CONFIG_ISO_PARTITION
-
-#define CONFIG_TIMESTAMP /* Print image info with timestamp */
-
-
-/*
- * BOOTP options
- */
-#define CONFIG_BOOTP_BOOTFILESIZE
-#define CONFIG_BOOTP_BOOTPATH
-#define CONFIG_BOOTP_GATEWAY
-#define CONFIG_BOOTP_HOSTNAME
-
-
-/*
- * Command line configuration.
- */
-#include <config_cmd_default.h>
-
-#define CONFIG_CMD_NFS
-#define CONFIG_CMD_SNTP
-
-#if defined(CONFIG_PCI)
-#define CODFIG_CMD_PCI
-#endif
-
-
-/*
- * Autobooting
- */
-#define CONFIG_BOOTDELAY 5 /* autoboot after 5 seconds */
-
-#define CONFIG_PREBOOT "echo;" \
- "echo Type \\\"run flash_nfs\\\" to mount root filesystem over NFS;" \
- "echo"
-
-#undef CONFIG_BOOTARGS
-
-#define CONFIG_EXTRA_ENV_SETTINGS \
- "netdev=eth0\0" \
- "nfsargs=setenv bootargs root=/dev/nfs rw " \
- "nfsroot=${serverip}:${rootpath}\0" \
- "ramargs=setenv bootargs root=/dev/ram rw\0" \
- "addip=setenv bootargs ${bootargs} " \
- "ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}" \
- ":${hostname}:${netdev}:off panic=1\0" \
- "flash_nfs=run nfsargs addip addcons;" \
- "bootm ${kernel_addr}\0" \
- "flash_self=run ramargs addip;" \
- "bootm ${kernel_addr} ${ramdisk_addr}\0" \
- "addcons=setenv bootargs ${bootargs} console=${contyp}," \
- "${baudrate}\0" \
- "contyp=ttyS0\0" \
- "net_nfs=tftp 200000 ${bootfile};run nfsargs addip addcons;" \
- "bootm\0" \
- "rootpath=/opt/eldk/ppc_6xx\0" \
- "bootfile=/tftpboot/jupiter/uImage\0" \
- ""
-
-#define CONFIG_BOOTCOMMAND "run flash_self"
-
-/*
- * IPB Bus clocking configuration.
- */
-#undef CONFIG_SYS_IPBSPEED_133 /* define for 133MHz speed */
-
-#if 0
-/* pass open firmware flat tree */
-#define CONFIG_OF_LIBFDT 1
-#define CONFIG_OF_BOARD_SETUP 1
-
-#define OF_CPU "PowerPC,5200@0"
-#define OF_SOC "soc5200@f0000000"
-#define OF_TBCLK (bd->bi_busfreq / 8)
-#define OF_STDOUT_PATH "/soc5200@f0000000/serial@2000"
-#endif
-
-#if 0
-/*
- * I2C configuration
- */
-#define CONFIG_HARD_I2C 1 /* I2C with hardware support */
-#define CONFIG_SYS_I2C_MODULE 2 /* Select I2C module #1 or #2 */
-
-#define CONFIG_SYS_I2C_SPEED 100000 /* 100 kHz */
-#define CONFIG_SYS_I2C_SLAVE 0x7F
-
-/*
- * EEPROM configuration
- */
-#define CONFIG_SYS_I2C_EEPROM_ADDR 0x50 /* 1010000x */
-#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1
-#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 3
-#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 70
-#endif
-
-/*
- * Flash configuration
- */
-#define CONFIG_SYS_FLASH_BASE 0xFF000000
-#define CONFIG_SYS_FLASH_SIZE 0x01000000
-
-#define CONFIG_SYS_MAX_FLASH_SECT 128 /* max num of sects on one chip */
-
-#define CONFIG_ENV_ADDR (CONFIG_SYS_TEXT_BASE + 0x40000) /* third sector */
-
-#define CONFIG_SYS_FLASH_ERASE_TOUT 240000 /* Flash Erase Timeout (in ms) */
-#define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (in ms) */
-
-#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* max num of flash banks */
-
-#define CONFIG_FLASH_CFI_DRIVER
-#define CONFIG_SYS_FLASH_CFI
-#define CONFIG_SYS_FLASH_EMPTY_INFO
-#define CONFIG_SYS_FLASH_CFI_WIDTH FLASH_CFI_8BIT
-#define CONFIG_SYS_UPDATE_FLASH_SIZE 1
-#define CONFIG_SYS_FLASH_USE_BUFFER_WRITE 1
-
-/*
- * Environment settings
- */
-#define CONFIG_ENV_IS_IN_FLASH 1
-#define CONFIG_ENV_SIZE 0x20000
-#define CONFIG_ENV_SECT_SIZE 0x20000
-#define CONFIG_ENV_OVERWRITE 1
-
-/* Address and size of Redundant Environment Sector */
-#define CONFIG_ENV_ADDR_REDUND (CONFIG_ENV_ADDR + CONFIG_ENV_SECT_SIZE)
-#define CONFIG_ENV_SIZE_REDUND (CONFIG_ENV_SIZE)
-
-/*
- * Memory map
- */
-#define CONFIG_SYS_MBAR 0xF0000000
-#define CONFIG_SYS_SDRAM_BASE 0x00000000
-#define CONFIG_SYS_DEFAULT_MBAR 0x80000000
-
-/* Use SRAM until RAM will be available */
-#define CONFIG_SYS_INIT_RAM_ADDR MPC5XXX_SRAM
-#define CONFIG_SYS_INIT_RAM_SIZE MPC5XXX_SRAM_SIZE /* Size of used area in DPRAM */
-
-
-#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
-#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET
-
-#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE
-#if (CONFIG_SYS_MONITOR_BASE < CONFIG_SYS_FLASH_BASE)
-# define CONFIG_SYS_RAMBOOT 1
-#endif
-
-#define CONFIG_SYS_MONITOR_LEN (192 << 10) /* Reserve 192 kB for Monitor */
-#define CONFIG_SYS_MALLOC_LEN (128 << 10) /* Reserve 128 kB for malloc() */
-#define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */
-
-/*
- * Ethernet configuration
- */
-#define CONFIG_MPC5xxx_FEC 1
-#define CONFIG_MPC5xxx_FEC_MII100
-/*
- * Define CONFIG_MPC5xxx_FEC_MII10 to force FEC at 10Mb
- */
-/* #define CONFIG_MPC5xxx_FEC_MII10 */
-#define CONFIG_PHY_ADDR 0x00
-
-/*
- * GPIO configuration
- */
-#define CONFIG_SYS_GPS_PORT_CONFIG 0x10000004
-
-/*
- * Miscellaneous configurable options
- */
-#define CONFIG_SYS_LONGHELP /* undef to save memory */
-
-#define CONFIG_CMDLINE_EDITING 1 /* add command line history */
-#define CONFIG_SYS_HUSH_PARSER 1 /* Use the HUSH parser */
-#if defined(CONFIG_CMD_KGDB)
-#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */
-#else
-#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */
-#endif
-#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */
-#define CONFIG_SYS_MAXARGS 16 /* max number of command args */
-#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */
-
-#define CONFIG_SYS_MEMTEST_START 0x00100000 /* memtest works on */
-#define CONFIG_SYS_MEMTEST_END 0x00f00000 /* 1 ... 15 MB in DRAM */
-#define CONFIG_SYS_ALT_MEMTEST 1
-
-#define CONFIG_SYS_LOAD_ADDR 0x200000 /* default load address */
-
-#define CONFIG_SYS_CACHELINE_SIZE 32 /* For MPC5xxx CPUs */
-#if defined(CONFIG_CMD_KGDB)
-# define CONFIG_SYS_CACHELINE_SHIFT 5 /* log base 2 of the above value */
-#endif
-
-/*
- * Various low-level settings
- */
-#define CONFIG_SYS_HID0_INIT HID0_ICE | HID0_ICFI
-#define CONFIG_SYS_HID0_FINAL HID0_ICE
-
-#define CONFIG_SYS_BOOTCS_START CONFIG_SYS_FLASH_BASE
-#define CONFIG_SYS_BOOTCS_SIZE CONFIG_SYS_FLASH_SIZE
-#define CONFIG_SYS_BOOTCS_CFG 0x00047801
-#define CONFIG_SYS_CS0_START CONFIG_SYS_FLASH_BASE
-#define CONFIG_SYS_CS0_SIZE CONFIG_SYS_FLASH_SIZE
-
-#define CONFIG_SYS_CS_BURST 0x00000000
-#define CONFIG_SYS_CS_DEADCYCLE 0x33333333
-
-#define CONFIG_SYS_RESET_ADDRESS 0xff000000
-
-#endif /* __CONFIG_H */
projects / platform / kernel / u-boot.git / blobdiff