arm: mach-omap2: Generate MLO file from SD boot capable targets

[platform/kernel/u-boot.git] / include / configs / jupiter.h

diff --git a/include/configs/jupiter.h b/include/configs/jupiter.h
index 7dfaa22..4461623 100644 (file)
--- a/include/configs/jupiter.h
+++ b/include/configs/jupiter.h
@@ -28,7 +28,6 @@
 #define CONFIG_SYS_MPC5XXX_CLKIN       33000000 /* ... running at 33.000000MHz */
 
 #define CONFIG_BOARD_EARLY_INIT_R      1
-#define CONFIG_BOARD_EARLY_INIT_F      1
 
 #define CONFIG_HIGH_BATS       1       /* High BATs supported */
 
@@ -36,7 +35,6 @@
  * Serial console configuration
  */
 #define CONFIG_PSC_CONSOLE     1       /* console is on PSC1 */
-#define CONFIG_BAUDRATE                115200  /* ... at 115200 bps */
 #define CONFIG_SYS_BAUDRATE_TABLE      { 9600, 19200, 38400, 57600, 115200, 230400 }
 
 /*
@@ -44,10 +42,8 @@
  * 0x40000000 - 0x4fffffff - PCI Memory
  * 0x50000000 - 0x50ffffff - PCI IO Space
  */
-/*#define CONFIG_PCI           */
 
 #if defined(CONFIG_PCI)
-#define CONFIG_PCI_PNP         1
 #define CONFIG_PCI_SCAN_SHOW   1
 #define CONFIG_PCIAUTO_SKIP_HOST_BRIDGE        1
 
@@ -66,13 +62,9 @@
 #define CONFIG_SYS_RX_ETH_BUFFER       8  /* use 8 rx buffer on eepro100  */
 
 /* Partitions */
-#define CONFIG_MAC_PARTITION
-#define CONFIG_DOS_PARTITION
-#define CONFIG_ISO_PARTITION
 
 #define        CONFIG_TIMESTAMP                /* Print image info with timestamp */
 
-
 /*
  * BOOTP options
  */
@@ -81,24 +73,17 @@
 #define CONFIG_BOOTP_GATEWAY
 #define CONFIG_BOOTP_HOSTNAME
 
-
 /*
  * Command line configuration.
  */
-#include <config_cmd_default.h>
-
-#define CONFIG_CMD_NFS
-#define CONFIG_CMD_SNTP
 
 #if defined(CONFIG_PCI)
 #define CODFIG_CMD_PCI
 #endif
 
-
 /*
  * Autobooting
  */
-#define CONFIG_BOOTDELAY       5       /* autoboot after 5 seconds */
 
 #define CONFIG_PREBOOT "echo;" \
        "echo Type \\\"run flash_nfs\\\" to mount root filesystem over NFS;" \
@@ -136,34 +121,12 @@
 
 #if 0
 /* pass open firmware flat tree */
-#define CONFIG_OF_LIBFDT       1
-#define CONFIG_OF_BOARD_SETUP  1
-
 #define OF_CPU                 "PowerPC,5200@0"
 #define OF_SOC                 "soc5200@f0000000"
 #define OF_TBCLK               (bd->bi_busfreq / 8)
 #define OF_STDOUT_PATH         "/soc5200@f0000000/serial@2000"
 #endif
 
-#if 0
-/*
- * I2C configuration
- */
-#define CONFIG_HARD_I2C                1       /* I2C with hardware support */
-#define CONFIG_SYS_I2C_MODULE          2       /* Select I2C module #1 or #2 */
-
-#define CONFIG_SYS_I2C_SPEED           100000 /* 100 kHz */
-#define CONFIG_SYS_I2C_SLAVE           0x7F
-
-/*
- * EEPROM configuration
- */
-#define CONFIG_SYS_I2C_EEPROM_ADDR             0x50    /* 1010000x */
-#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN         1
-#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS      3
-#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS  70
-#endif
-
 /*
  * Flash configuration
  */
@@ -209,7 +172,6 @@
 #define CONFIG_SYS_INIT_RAM_ADDR       MPC5XXX_SRAM
 #define CONFIG_SYS_INIT_RAM_SIZE       MPC5XXX_SRAM_SIZE       /* Size of used area in DPRAM */
 
-
 #define CONFIG_SYS_GBL_DATA_OFFSET     (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
 #define CONFIG_SYS_INIT_SP_OFFSET      CONFIG_SYS_GBL_DATA_OFFSET
 
@@ -244,7 +206,6 @@
 #define CONFIG_SYS_LONGHELP                    /* undef to save memory     */
 
 #define CONFIG_CMDLINE_EDITING 1       /* add command line history     */
-#define CONFIG_SYS_HUSH_PARSER         1       /* Use the HUSH parser          */
 #if defined(CONFIG_CMD_KGDB)
 #define CONFIG_SYS_CBSIZE              1024    /* Console I/O Buffer Size  */
 #else