global: Move remaining CONFIG_SYS_SDRAM_* to CFG_SYS_SDRAM_*

[platform/kernel/u-boot.git] / include / configs / integrator-common.h

diff --git a/include/configs/integrator-common.h b/include/configs/integrator-common.h
index 63aa8df..8d0458d 100644 (file)
--- a/include/configs/integrator-common.h
+++ b/include/configs/integrator-common.h
@@ -1,50 +1,12 @@
+/* SPDX-License-Identifier: GPL-2.0+ */
 /*
  * (C) Copyright 2012
  * Linaro
  * Linus Walleij <linus.walleij@linaro.org>
  * Common ARM Integrator configuration settings
- *
- * SPDX-License-Identifier:    GPL-2.0+
  */
 
-#define CONFIG_SYS_MEMTEST_START       0x100000
-#define CONFIG_SYS_MEMTEST_END         0x10000000
 #define CONFIG_SYS_TIMERBASE           0x13000100      /* Timer1 */
-#define CONFIG_SYS_LOAD_ADDR           0x7fc0  /* default load address */
-#define CONFIG_SYS_MALLOC_LEN          (CONFIG_ENV_SIZE + 128*1024) /* Size of malloc() pool */
-
-#define CONFIG_CONS_INDEX              0
-
-#define CONFIG_CMDLINE_TAG             /* enable passing of ATAGs  */
-#define CONFIG_SETUP_MEMORY_TAGS
-#define CONFIG_MISC_INIT_R             /* call misc_init_r during start up */
-
-/*
- * There are various dependencies on the core module (CM) fitted
- * Users should refer to their CM user guide
- */
-#include "armcoremodule.h"
-
-/*
- * Initialize and remap the core module, use SPD to detect memory size
- * If CONFIG_SKIP_LOWLEVEL_INIT is not defined &
- * the core module has a CM_INIT register
- * then the U-Boot initialisation code will
- * e.g. ARM Boot Monitor or pre-loader is repeated once
- * (to re-initialise any existing CM_INIT settings to safe values).
- *
- * This is usually not the desired behaviour since the platform
- * will either reboot into the ARM monitor (or pre-loader)
- * or continuously cycle thru it without U-Boot running,
- * depending upon the setting of Integrator/CP switch S2-4.
- *
- * However it may be needed if Integrator/CP switch S2-1
- * is set OFF to boot direct into U-Boot.
- * In that case comment out the line below.
- */
-#define CONFIG_CM_INIT
-#define CONFIG_CM_REMAP
-#define CONFIG_CM_SPD_DETECT
 
 /*
  * The ARM boot monitor initializes the board.
@@ -54,7 +16,6 @@
  * image to run at reset/power up
  * e.g. whether the ARM Boot Monitor runs before U-Boot
  */
-/* #define CONFIG_SKIP_LOWLEVEL_INIT */
 
 /*
  * The ARM boot monitor does not relocate U-Boot.
@@ -67,15 +28,9 @@
 /*
  * Physical Memory Map
  */
-#define CONFIG_NR_DRAM_BANKS   1               /* we have 1 bank of DRAM */
 #define PHYS_SDRAM_1           0x00000000      /* SDRAM Bank #1 */
 #define PHYS_SDRAM_1_SIZE      0x08000000      /* 128 MB */
-#define CONFIG_SYS_SDRAM_BASE  PHYS_SDRAM_1
-#define CONFIG_SYS_INIT_RAM_SIZE PHYS_SDRAM_1_SIZE
-#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_SDRAM_BASE + \
-                                   CONFIG_SYS_INIT_RAM_SIZE - \
-                                   GENERATED_GBL_DATA_SIZE)
-#define CONFIG_SYS_INIT_SP_ADDR CONFIG_SYS_GBL_DATA_OFFSET
+#define CFG_SYS_SDRAM_BASE     PHYS_SDRAM_1
 
 /*
  * FLASH and environment organization
@@ -86,13 +41,6 @@
  * - SIB block
  * - U-Boot environment
  */
-#define CONFIG_SYS_FLASH_CFI           1
-#define CONFIG_FLASH_CFI_DRIVER                1
 #define CONFIG_SYS_FLASH_BASE          0x24000000
-#define CONFIG_SYS_MAX_FLASH_BANKS     1
 
 /* Timeout values in ticks */
-#define CONFIG_SYS_FLASH_ERASE_TOUT    (2 * CONFIG_SYS_HZ) /* Erase Timeout */
-#define CONFIG_SYS_FLASH_WRITE_TOUT    (2 * CONFIG_SYS_HZ) /* Write Timeout */
-#define CONFIG_SYS_FLASH_PROTECTION    /* The devices have real protection */
-#define CONFIG_SYS_FLASH_EMPTY_INFO    /* flinfo indicates empty blocks */