+++ /dev/null
-/*
- * (C) Copyright 2009
- * Detlev Zundel, DENX Software Engineering, dzu@denx.de.
- *
- * (C) Copyright 2003-2005
- * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
- *
- * SPDX-License-Identifier: GPL-2.0+
- */
-
-#ifndef __CONFIG_H
-#define __CONFIG_H
-
-/*
- * High Level Configuration Options
- * (easy to change)
- */
-
-#define CONFIG_MPC5200 1 /* This is an MPC5200 CPU */
-#define CONFIG_INKA4X0 1 /* INKA4x0 board */
-#define CONFIG_SYS_GENERIC_BOARD
-#define CONFIG_DISPLAY_BOARDINFO
-
-/*
- * Valid values for CONFIG_SYS_TEXT_BASE are:
- * 0xFFE00000 boot low
- * 0x00100000 boot from RAM (for testing only)
- */
-#ifndef CONFIG_SYS_TEXT_BASE
-#define CONFIG_SYS_TEXT_BASE 0xFFE00000 /* Standard: boot low */
-#endif
-#define CONFIG_SYS_LDSCRIPT "arch/powerpc/cpu/mpc5xxx/u-boot-customlayout.lds"
-
-#define CONFIG_SYS_MPC5XXX_CLKIN 33000000 /* ... running at 33.000000MHz */
-
-#define CONFIG_MISC_INIT_F 1 /* Use misc_init_f() */
-
-#define CONFIG_HIGH_BATS 1 /* High BATs supported */
-
-/*
- * Serial console configuration
- */
-#define CONFIG_PSC_CONSOLE 1 /* console is on PSC1 */
-#define CONFIG_BAUDRATE 115200 /* ... at 115200 bps */
-#define CONFIG_SYS_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200, 230400 }
-
-/*
- * PCI Mapping:
- * 0x40000000 - 0x4fffffff - PCI Memory
- * 0x50000000 - 0x50ffffff - PCI IO Space
- */
-#define CONFIG_PCI 1
-#define CONFIG_PCI_PNP 1
-#define CONFIG_PCI_SCAN_SHOW 1
-#define CONFIG_PCIAUTO_SKIP_HOST_BRIDGE 1
-
-#define CONFIG_PCI_MEM_BUS 0x40000000
-#define CONFIG_PCI_MEM_PHYS CONFIG_PCI_MEM_BUS
-#define CONFIG_PCI_MEM_SIZE 0x10000000
-
-#define CONFIG_PCI_IO_BUS 0x50000000
-#define CONFIG_PCI_IO_PHYS CONFIG_PCI_IO_BUS
-#define CONFIG_PCI_IO_SIZE 0x01000000
-
-#define CONFIG_SYS_XLB_PIPELINING 1
-
-/* Partitions */
-#define CONFIG_MAC_PARTITION
-#define CONFIG_DOS_PARTITION
-#define CONFIG_ISO_PARTITION
-
-
-/*
- * BOOTP options
- */
-#define CONFIG_BOOTP_BOOTFILESIZE
-#define CONFIG_BOOTP_BOOTPATH
-#define CONFIG_BOOTP_GATEWAY
-#define CONFIG_BOOTP_HOSTNAME
-
-
-/*
- * Command line configuration.
- */
-#define CONFIG_CMD_DATE
-#define CONFIG_CMD_DHCP
-#define CONFIG_CMD_EXT2
-#define CONFIG_CMD_FAT
-#define CONFIG_CMD_IDE
-#define CONFIG_CMD_PCI
-#define CONFIG_CMD_PING
-#define CONFIG_CMD_SNTP
-#define CONFIG_CMD_USB
-
-#define CONFIG_TIMESTAMP 1 /* Print image info with timestamp */
-
-#if (CONFIG_SYS_TEXT_BASE == 0xFFE00000) /* Boot low */
-# define CONFIG_SYS_LOWBOOT 1
-#endif
-
-/*
- * Autobooting
- */
-#define CONFIG_BOOTDELAY 1 /* autoboot after 1 second */
-
-#define CONFIG_PREBOOT "echo;" \
- "echo Type \\\"run flash_nfs\\\" to mount root filesystem over NFS;" \
- "echo"
-
-#undef CONFIG_BOOTARGS
-
-#define CONFIG_IPADDR 192.168.100.2
-#define CONFIG_SERVERIP 192.168.100.1
-#define CONFIG_NETMASK 255.255.255.0
-#define HOSTNAME inka4x0
-#define CONFIG_BOOTFILE "/tftpboot/inka4x0/uImage"
-#define CONFIG_ROOTPATH "/opt/eldk/ppc_6xx"
-
-#define CONFIG_EXTRA_ENV_SETTINGS \
- "netdev=eth0\0" \
- "nfsargs=setenv bootargs root=/dev/nfs rw " \
- "nfsroot=${serverip}:${rootpath}\0" \
- "ramargs=setenv bootargs root=/dev/ram rw\0" \
- "addip=setenv bootargs ${bootargs} " \
- "ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}" \
- ":${hostname}:${netdev}:off panic=1\0" \
- "addcons=setenv bootargs ${bootargs} " \
- "console=ttyS0,${baudrate}\0" \
- "flash_nfs=run nfsargs addip addcons;" \
- "bootm ${kernel_addr}\0" \
- "net_nfs=tftp 200000 ${bootfile};" \
- "run nfsargs addip addcons;bootm\0" \
- "enable_disp=mw.l 100000 04000000 1;" \
- "cp.l 100000 f0000b20 1;" \
- "cp.l 100000 f0000b28 1\0" \
- "ideargs=setenv bootargs root=/dev/hda1 rw\0" \
- "ide_boot=ext2load ide 0:1 200000 uImage;" \
- "run ideargs addip addcons enable_disp;bootm\0" \
- "brightness=255\0" \
- ""
-
-#define CONFIG_BOOTCOMMAND "run ide_boot"
-
-/*
- * IPB Bus clocking configuration.
- */
-#define CONFIG_SYS_IPBCLK_EQUALS_XLBCLK /* define for 133MHz speed */
-
-/*
- * Flash configuration
- */
-#define CONFIG_SYS_FLASH_CFI 1 /* Flash is CFI conformant */
-#define CONFIG_FLASH_CFI_DRIVER 1
-#define CONFIG_SYS_FLASH_BASE 0xffe00000
-#define CONFIG_SYS_FLASH_SIZE 0x00200000
-#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* max num of memory banks */
-#define CONFIG_SYS_FLASH_BANKS_LIST { CONFIG_SYS_FLASH_BASE }
-#define CONFIG_SYS_MAX_FLASH_SECT 128 /* max num of sects on one chip */
-#define CONFIG_SYS_FLASH_USE_BUFFER_WRITE 1 /* use buffered writes (20x faster) */
-
-/*
- * Environment settings
- */
-#define CONFIG_ENV_IS_IN_FLASH 1
-#define CONFIG_ENV_ADDR (CONFIG_SYS_FLASH_BASE + 0x4000)
-#define CONFIG_ENV_SIZE 0x2000
-#define CONFIG_ENV_SECT_SIZE 0x2000
-#define CONFIG_ENV_OVERWRITE 1
-#define CONFIG_SYS_USE_PPCENV /* Environment embedded in sect .ppcenv */
-
-/*
- * Memory map
- */
-#define CONFIG_SYS_MBAR 0xF0000000
-#define CONFIG_SYS_SDRAM_BASE 0x00000000
-#define CONFIG_SYS_DEFAULT_MBAR 0x80000000
-
-/*
- * SDRAM controller configuration
- */
-#undef CONFIG_SDR_MT48LC16M16A2
-#undef CONFIG_DDR_MT46V16M16
-#undef CONFIG_DDR_MT46V32M16
-#undef CONFIG_DDR_HYB25D512160BF
-#define CONFIG_DDR_K4H511638C
-
-/* Use ON-Chip SRAM until RAM will be available */
-#define CONFIG_SYS_INIT_RAM_ADDR MPC5XXX_SRAM
-
-/* preserve space for the post_word at end of on-chip SRAM */
-#define MPC5XXX_SRAM_POST_SIZE (MPC5XXX_SRAM_SIZE - 4)
-
-#ifdef CONFIG_POST
-#define CONFIG_SYS_INIT_RAM_SIZE MPC5XXX_SRAM_POST_SIZE
-#else
-#define CONFIG_SYS_INIT_RAM_SIZE MPC5XXX_SRAM_SIZE
-#endif
-
-#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
-#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET
-
-#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE
-#if (CONFIG_SYS_MONITOR_BASE < CONFIG_SYS_FLASH_BASE)
-# define CONFIG_SYS_RAMBOOT 1
-#endif
-
-#define CONFIG_SYS_MONITOR_LEN (256 << 10) /* Reserve 256 kB for Monitor */
-#define CONFIG_SYS_MALLOC_LEN (128 << 10) /* Reserve 128 kB for malloc() */
-#define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */
-
-/*
- * Ethernet configuration
- */
-#define CONFIG_MPC5xxx_FEC 1
-#define CONFIG_MPC5xxx_FEC_MII100
-/*
- * Define CONFIG_MPC5xxx_FEC_MII10 to force FEC at 10Mb
- */
-/* #define CONFIG_MPC5xxx_FEC_MII10 */
-#define CONFIG_PHY_ADDR 0x00
-#define CONFIG_MII
-
-/*
- * GPIO configuration
- *
- * use CS1 as gpio_wkup_6 output
- * Bit 0 (mask: 0x80000000): 0
- * use ALT CAN position: Bits 2-3 (mask: 0x30000000):
- * 00 -> No Alternatives, I2C1 is used for onboard EEPROM
- * 01 -> CAN1 on I2C1, CAN2 on Tmr0/1 do not use on TQM5200 with onboard
- * EEPROM
- * use PSC1 as UART: Bits 28-31 (mask: 0x00000007): 0100
- * use PSC2 as UART: Bits 24-27 (mask: 0x00000070): 0100
- * use PSC3 as UART: Bits 20-23 (mask: 0x00000700): 0100
- * use PSC6 as UART: Bits 9-11 (mask: 0x00700000): 0101
- */
-#define CONFIG_SYS_GPS_PORT_CONFIG 0x01501444
-
-/*
- * RTC configuration
- */
-#define CONFIG_RTC_RTC4543 1 /* use external RTC */
-
-/*
- * Software (bit-bang) three wire serial configuration
- *
- * Note that we need the ifdefs because otherwise compilation of
- * mkimage.c fails.
- */
-#define CONFIG_SOFT_TWS 1
-
-#ifdef TWS_IMPLEMENTATION
-#include <mpc5xxx.h>
-#include <asm/io.h>
-
-#define TWS_CE MPC5XXX_GPIO_WKUP_PSC1_4 /* GPIO_WKUP_0 */
-#define TWS_WR MPC5XXX_GPIO_WKUP_PSC2_4 /* GPIO_WKUP_1 */
-#define TWS_DATA MPC5XXX_GPIO_SINT_PSC3_4 /* GPIO_SINT_0 */
-#define TWS_CLK MPC5XXX_GPIO_SINT_PSC3_5 /* GPIO_SINT_1 */
-
-static inline void tws_ce(unsigned bit)
-{
- struct mpc5xxx_wu_gpio *wu_gpio =
- (struct mpc5xxx_wu_gpio *)MPC5XXX_WU_GPIO;
- if (bit)
- setbits_8(&wu_gpio->dvo, TWS_CE);
- else
- clrbits_8(&wu_gpio->dvo, TWS_CE);
-}
-
-static inline void tws_wr(unsigned bit)
-{
- struct mpc5xxx_wu_gpio *wu_gpio =
- (struct mpc5xxx_wu_gpio *)MPC5XXX_WU_GPIO;
- if (bit)
- setbits_8(&wu_gpio->dvo, TWS_WR);
- else
- clrbits_8(&wu_gpio->dvo, TWS_WR);
-}
-
-static inline void tws_clk(unsigned bit)
-{
- struct mpc5xxx_gpio *gpio =
- (struct mpc5xxx_gpio *)MPC5XXX_GPIO;
- if (bit)
- setbits_8(&gpio->sint_dvo, TWS_CLK);
- else
- clrbits_8(&gpio->sint_dvo, TWS_CLK);
-}
-
-static inline void tws_data(unsigned bit)
-{
- struct mpc5xxx_gpio *gpio =
- (struct mpc5xxx_gpio *)MPC5XXX_GPIO;
- if (bit)
- setbits_8(&gpio->sint_dvo, TWS_DATA);
- else
- clrbits_8(&gpio->sint_dvo, TWS_DATA);
-}
-
-static inline unsigned tws_data_read(void)
-{
- struct mpc5xxx_gpio *gpio =
- (struct mpc5xxx_gpio *)MPC5XXX_GPIO;
- return !!(in_8(&gpio->sint_ival) & TWS_DATA);
-}
-
-static inline void tws_data_config_output(unsigned output)
-{
- struct mpc5xxx_gpio *gpio =
- (struct mpc5xxx_gpio *)MPC5XXX_GPIO;
- if (output)
- setbits_8(&gpio->sint_ddr, TWS_DATA);
- else
- clrbits_8(&gpio->sint_ddr, TWS_DATA);
-}
-#endif /* TWS_IMPLEMENTATION */
-
-/*
- * Miscellaneous configurable options
- */
-#define CONFIG_SYS_LONGHELP /* undef to save memory */
-#if defined(CONFIG_CMD_KGDB)
-#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */
-#else
-#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */
-#endif
-#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */
-#define CONFIG_SYS_MAXARGS 16 /* max number of command args */
-#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */
-
-#define CONFIG_SYS_CACHELINE_SIZE 32 /* For MPC5xxx CPUs */
-#if defined(CONFIG_CMD_KGDB)
-# define CONFIG_SYS_CACHELINE_SHIFT 5 /* log base 2 of the above value */
-#endif
-
-/* Enable an alternate, more extensive memory test */
-#define CONFIG_SYS_ALT_MEMTEST
-
-#define CONFIG_SYS_MEMTEST_START 0x00100000 /* memtest works on */
-#define CONFIG_SYS_MEMTEST_END 0x00f00000 /* 1 ... 15 MB in DRAM */
-
-#define CONFIG_SYS_LOAD_ADDR 0x100000 /* default load address */
-
-/*
- * Enable loopw command.
- */
-#define CONFIG_LOOPW
-
-/*
- * Various low-level settings
- */
-#define CONFIG_SYS_HID0_INIT HID0_ICE | HID0_ICFI
-#define CONFIG_SYS_HID0_FINAL HID0_ICE
-
-#define CONFIG_SYS_BOOTCS_START CONFIG_SYS_FLASH_BASE
-#define CONFIG_SYS_BOOTCS_SIZE CONFIG_SYS_FLASH_SIZE
-#define CONFIG_SYS_BOOTCS_CFG 0x00087800 /* for pci_clk = 66 MHz */
-#define CONFIG_SYS_CS0_START CONFIG_SYS_FLASH_BASE
-#define CONFIG_SYS_CS0_SIZE CONFIG_SYS_FLASH_SIZE
-
-/* 32Mbit SRAM @0x30000000 */
-#define CONFIG_SYS_CS1_START 0x30000000
-#define CONFIG_SYS_CS1_SIZE 0x00400000
-#define CONFIG_SYS_CS1_CFG 0x31800 /* for pci_clk = 33 MHz */
-
-/* 2 quad UART @0x80000000 (MBAR is relocated to 0xF0000000) */
-#define CONFIG_SYS_CS2_START 0x80000000
-#define CONFIG_SYS_CS2_SIZE 0x0001000
-#define CONFIG_SYS_CS2_CFG 0x21800 /* for pci_clk = 33 MHz */
-
-/* GPIO in @0x30400000 */
-#define CONFIG_SYS_CS3_START 0x30400000
-#define CONFIG_SYS_CS3_SIZE 0x00100000
-#define CONFIG_SYS_CS3_CFG 0x31800 /* for pci_clk = 33 MHz */
-
-#define CONFIG_SYS_CS_BURST 0x00000000
-#define CONFIG_SYS_CS_DEADCYCLE 0x33333333
-
-/*-----------------------------------------------------------------------
- * USB stuff
- *-----------------------------------------------------------------------
- */
-#define CONFIG_USB_OHCI
-#define CONFIG_USB_CLOCK 0x00015555
-#define CONFIG_USB_CONFIG 0x00001000
-#define CONFIG_USB_STORAGE
-
-/*-----------------------------------------------------------------------
- * IDE/ATA stuff Supports IDE harddisk
- *-----------------------------------------------------------------------
- */
-
-#undef CONFIG_IDE_8xx_PCCARD /* Use IDE with PC Card Adapter */
-
-#undef CONFIG_IDE_8xx_DIRECT /* Direct IDE not supported */
-#undef CONFIG_IDE_LED /* LED for ide not supported */
-
-#define CONFIG_IDE_PREINIT
-
-#define CONFIG_SYS_IDE_MAXBUS 1 /* max. 1 IDE bus */
-#define CONFIG_SYS_IDE_MAXDEVICE 2 /* max. 1 drive per IDE bus */
-
-#define CONFIG_SYS_ATA_IDE0_OFFSET 0x0000
-#define CONFIG_SYS_ATA_BASE_ADDR MPC5XXX_ATA
-#define CONFIG_SYS_ATA_DATA_OFFSET 0x0060 /* Offset for data I/O */
-#define CONFIG_SYS_ATA_REG_OFFSET (CONFIG_SYS_ATA_DATA_OFFSET) /* Offset for normal register accesses */
-#define CONFIG_SYS_ATA_ALT_OFFSET 0x005C /* Offset for alternate registers */
-#define CONFIG_SYS_ATA_STRIDE 4 /* Interval between registers */
-
-#define CONFIG_ATAPI 1
-
-#define CONFIG_SYS_BRIGHTNESS 0xFF /* LCD Default Brightness (255 = off) */
-
-#endif /* __CONFIG_H */
projects / platform / kernel / u-boot.git / blobdiff