+/* SPDX-License-Identifier: GPL-2.0+ */
/*
* (C) Copyright 2013
* Heiko Schocher, DENX Software Engineering, hs@denx.de.
* Based on:
* Copyright (c) 2011 IDS GmbH, Germany
* Sergej Stepanov <ste@ids.de>
- *
- * SPDX-License-Identifier: GPL-2.0+
*/
#ifndef __CONFIG_H
#define __CONFIG_H
+#include <linux/stringify.h>
+
/*
* High Level Configuration Options
*/
-#define CONFIG_MPC831x
-#define CONFIG_MPC8313
-
-#define CONFIG_FSL_ELBC
-
-#define CONFIG_MISC_INIT_R
-
#define CONFIG_BOOT_RETRY_TIME 900
#define CONFIG_BOOT_RETRY_MIN 30
#define CONFIG_RESET_TO_RETRY
-#define CONFIG_83XX_CLKIN 66000000 /* in Hz */
-#define CONFIG_SYS_CLK_FREQ CONFIG_83XX_CLKIN
-
-#define CONFIG_SYS_IMMR 0xF0000000
-
-#define CONFIG_SYS_ACR_PIPE_DEP 3 /* Arbiter pipeline depth (0-3) */
-#define CONFIG_SYS_ACR_RPTCNT 3 /* Arbiter repeat count (0-7) */
-
-/*
- * Hardware Reset Configuration Word
- * if CLKIN is 66.000MHz, then
- * CSB = 132MHz, CORE = 264MHz, DDRC = 264MHz, LBC = 132MHz
- */
-#define CONFIG_SYS_HRCW_LOW (0x20000000 /* reserved, must be set */ |\
- HRCWL_DDR_TO_SCB_CLK_2X1 |\
- HRCWL_CSB_TO_CLKIN_2X1 |\
- HRCWL_CORE_TO_CSB_2X1)
-
-#define CONFIG_SYS_HRCW_HIGH (HRCWH_PCI_HOST |\
- HRCWH_CORE_ENABLE |\
- HRCWH_FROM_0XFFF00100 |\
- HRCWH_BOOTSEQ_DISABLE |\
- HRCWH_SW_WATCHDOG_DISABLE |\
- HRCWH_ROM_LOC_LOCAL_8BIT |\
- HRCWH_RL_EXT_LEGACY |\
- HRCWH_TSEC1M_IN_MII |\
- HRCWH_TSEC2M_IN_MII |\
- HRCWH_BIG_ENDIAN)
-
#define CONFIG_SYS_SICRH 0x00000000
#define CONFIG_SYS_SICRL (SICRL_LBC | SICRL_SPI_D)
#define CONFIG_HWCONFIG
-#define CONFIG_SYS_HID0_INIT 0x000000000
-#define CONFIG_SYS_HID0_FINAL (HID0_ENABLE_MACHINE_CHECK |\
- HID0_ENABLE_INSTRUCTION_CACHE |\
- HID0_DISABLE_DYNAMIC_POWER_MANAGMENT)
-
-#define CONFIG_SYS_HID2 (HID2_HBE | 0x00020000)
-
/*
* Definitions for initial stack pointer and data area (in DCACHE )
*/
#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET
/*
- * Local Bus LCRR and LBCR regs
- */
-#define CONFIG_SYS_LCRR_EADC LCRR_EADC_1
-#define CONFIG_SYS_LCRR_CLKDIV LCRR_CLKDIV_2
-#define CONFIG_SYS_LBC_LBCR (0x00040000 |\
- (0xFF << LBCR_BMT_SHIFT) |\
- 0xF)
-
-#define CONFIG_SYS_LBC_MRTPR 0x20000000
-
-/*
* Internal Definitions
*/
/*
* DDR Setup
*/
-#define CONFIG_SYS_DDR_BASE 0x00000000
-#define CONFIG_SYS_SDRAM_BASE CONFIG_SYS_DDR_BASE
-#define CONFIG_SYS_DDR_SDRAM_BASE CONFIG_SYS_DDR_BASE
+#define CONFIG_SYS_SDRAM_BASE 0x00000000
/*
* Manually set up DDR parameters,
*/
#define CONFIG_TSEC1
#define CONFIG_TSEC2
-#define CONFIG_HARD_SPI
/*
* NOR FLASH setup
*/
-#define CONFIG_SYS_FLASH_CFI
-#define CONFIG_FLASH_CFI_DRIVER
#define CONFIG_SYS_FLASH_CFI_WIDTH FLASH_CFI_8BIT
#define CONFIG_FLASH_SHOW_PROGRESS 50
-#define CONFIG_SYS_FLASH_USE_BUFFER_WRITE
#define CONFIG_SYS_FLASH_BASE 0xFF800000
#define CONFIG_SYS_FLASH_SIZE 8
-#define CONFIG_SYS_FLASH_PROTECTION
-
-#define CONFIG_SYS_LBLAWBAR0_PRELIM CONFIG_SYS_FLASH_BASE
-#define CONFIG_SYS_LBLAWAR0_PRELIM 0x80000016
-
-#define CONFIG_SYS_BR0_PRELIM (CONFIG_SYS_FLASH_BASE |\
- BR_PS_8 |\
- BR_MS_GPCM |\
- BR_V)
-
-#define CONFIG_SYS_OR0_PRELIM (MEG_TO_AM(CONFIG_SYS_FLASH_SIZE) |\
- OR_GPCM_SCY_10 |\
- OR_GPCM_EHTR |\
- OR_GPCM_TRLX |\
- OR_GPCM_CSNT |\
- OR_GPCM_EAD)
+
+
#define CONFIG_SYS_MAX_FLASH_BANKS 1
#define CONFIG_SYS_MAX_FLASH_SECT 128
*/
#define CONFIG_SYS_NAND_BASE 0xE1000000
#define CONFIG_SYS_MAX_NAND_DEVICE 1
-#define CONFIG_SYS_NAND_MAX_CHIPS 1
-#define CONFIG_NAND_FSL_ELBC
-#define CONFIG_SYS_NAND_PAGE_SIZE (2048)
-#define CONFIG_SYS_NAND_BLOCK_SIZE (128 << 10)
#define NAND_CACHE_PAGES 64
-#define CONFIG_SYS_LBLAWBAR1_PRELIM CONFIG_SYS_NAND_BASE
-#define CONFIG_SYS_LBLAWAR1_PRELIM 0x8000000E
-#define CONFIG_SYS_NAND_LBLAWBAR_PRELIM CONFIG_SYS_LBLAWBAR1_PRELIM
-#define CONFIG_SYS_NAND_LBLAWAR_PRELIM CONFIG_SYS_LBLAWAR1_PRELIM
-
-#define CONFIG_SYS_BR1_PRELIM ((CONFIG_SYS_NAND_BASE) |\
- (2<<BR_DECC_SHIFT) |\
- BR_PS_8 |\
- BR_MS_FCM |\
- BR_V)
-
-#define CONFIG_SYS_OR1_PRELIM (0xFFFF8000 |\
- OR_FCM_PGS |\
- OR_FCM_CSCT |\
- OR_FCM_CST |\
- OR_FCM_CHT |\
- OR_FCM_SCY_4 |\
- OR_FCM_TRLX |\
- OR_FCM_EHTR |\
- OR_FCM_RST)
/*
* MRAM setup
*/
#define CONFIG_SYS_MRAM_BASE 0xE2000000
#define CONFIG_SYS_MRAM_SIZE 0x20000 /* 128 Kb */
-#define CONFIG_SYS_LBLAWBAR2_PRELIM CONFIG_SYS_MRAM_BASE
-#define CONFIG_SYS_LBLAWAR2_PRELIM 0x80000010 /* 128 Kb */
#define CONFIG_SYS_OR_TIMING_MRAM
-#define CONFIG_SYS_BR2_PRELIM (CONFIG_SYS_MRAM_BASE |\
- BR_PS_8 |\
- BR_MS_GPCM |\
- BR_V)
-
-#define CONFIG_SYS_OR2_PRELIM 0xFFFE0C74
/*
* CPLD setup
*/
#define CONFIG_SYS_CPLD_BASE 0xE3000000
#define CONFIG_SYS_CPLD_SIZE 0x8000
-#define CONFIG_SYS_LBLAWBAR3_PRELIM CONFIG_SYS_CPLD_BASE
-#define CONFIG_SYS_LBLAWAR3_PRELIM 0x8000000E
#define CONFIG_SYS_OR_TIMING_MRAM
-#define CONFIG_SYS_BR3_PRELIM (CONFIG_SYS_CPLD_BASE |\
- BR_PS_8 |\
- BR_MS_GPCM |\
- BR_V)
-
-#define CONFIG_SYS_OR3_PRELIM 0xFFFF8814
/*
* HW-Watchdog
/*
* I2C setup
*/
-#define CONFIG_SYS_I2C
-#define CONFIG_SYS_I2C_FSL
-#define CONFIG_SYS_FSL_I2C_SPEED 400000
-#define CONFIG_SYS_FSL_I2C_SLAVE 0x7F
-#define CONFIG_SYS_FSL_I2C_OFFSET 0x3100
-#define CONFIG_RTC_PCF8563
#define CONFIG_SYS_I2C_RTC_ADDR 0x51
/*
- * SPI setup
- */
-#ifdef CONFIG_HARD_SPI
-#define CONFIG_SYS_GPIO1_PRELIM
-#define CONFIG_SYS_GPIO1_DIR 0x00000001
-#define CONFIG_SYS_GPIO1_DAT 0x00000001
-#endif
-
-/*
* Ethernet setup
*/
#ifdef CONFIG_TSEC1
{300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 115200}
#define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_IMMR + 0x4500)
#define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_IMMR + 0x4600)
-#define CONFIG_SYS_NS16550_CLK (CONFIG_83XX_CLKIN * 2)
+#define CONFIG_SYS_NS16550_CLK (get_bus_freq(0))
#define CONFIG_HAS_FSL_DR_USB
#define CONFIG_SYS_SCCR_USBDRCM 3
/*
- * BAT's
- */
-#define CONFIG_HIGH_BATS
-
-/* DDR @ 0x00000000 */
-#define CONFIG_SYS_IBAT0L (CONFIG_SYS_SDRAM_BASE |\
- BATL_PP_10)
-#define CONFIG_SYS_IBAT0U (CONFIG_SYS_SDRAM_BASE |\
- BATU_BL_256M |\
- BATU_VS |\
- BATU_VP)
-#define CONFIG_SYS_DBAT0L CONFIG_SYS_IBAT0L
-#define CONFIG_SYS_DBAT0U CONFIG_SYS_IBAT0U
-
-/* Initial RAM @ 0xFD000000 */
-#define CONFIG_SYS_IBAT1L (CONFIG_SYS_INIT_RAM_ADDR |\
- BATL_PP_10 |\
- BATL_GUARDEDSTORAGE)
-#define CONFIG_SYS_IBAT1U (CONFIG_SYS_INIT_RAM_ADDR |\
- BATU_BL_256K |\
- BATU_VS |\
- BATU_VP)
-#define CONFIG_SYS_DBAT1L CONFIG_SYS_IBAT1L
-#define CONFIG_SYS_DBAT1U CONFIG_SYS_IBAT1U
-
-/* FLASH @ 0xFF800000 */
-#define CONFIG_SYS_IBAT2L (CONFIG_SYS_FLASH_BASE |\
- BATL_PP_10 |\
- BATL_GUARDEDSTORAGE)
-#define CONFIG_SYS_IBAT2U (CONFIG_SYS_FLASH_BASE |\
- BATU_BL_8M |\
- BATU_VS |\
- BATU_VP)
-#define CONFIG_SYS_DBAT2L (CONFIG_SYS_FLASH_BASE |\
- BATL_PP_10 |\
- BATL_CACHEINHIBIT |\
- BATL_GUARDEDSTORAGE)
-#define CONFIG_SYS_DBAT2U CONFIG_SYS_IBAT2U
-
-#define CONFIG_SYS_IBAT3L (0)
-#define CONFIG_SYS_IBAT3U (0)
-#define CONFIG_SYS_DBAT3L CONFIG_SYS_IBAT3L
-#define CONFIG_SYS_DBAT3U CONFIG_SYS_IBAT3U
-
-#define CONFIG_SYS_IBAT4L (0)
-#define CONFIG_SYS_IBAT4U (0)
-#define CONFIG_SYS_DBAT4L CONFIG_SYS_IBAT4L
-#define CONFIG_SYS_DBAT4U CONFIG_SYS_IBAT4U
-
-/* IMMRBAR @ 0xF0000000 */
-#define CONFIG_SYS_IBAT5L (CONFIG_SYS_IMMR |\
- BATL_PP_10 |\
- BATL_CACHEINHIBIT |\
- BATL_GUARDEDSTORAGE)
-#define CONFIG_SYS_IBAT5U (CONFIG_SYS_IMMR |\
- BATU_BL_128M |\
- BATU_VS |\
- BATU_VP)
-#define CONFIG_SYS_DBAT5L CONFIG_SYS_IBAT5L
-#define CONFIG_SYS_DBAT5U CONFIG_SYS_IBAT5U
-
-/* NAND-Flash @ 0xE1000000, MRAM @ 0xE2000000, CPLD @ 0xE3000000 */
-#define CONFIG_SYS_IBAT6L (0xE0000000 |\
- BATL_PP_10 |\
- BATL_GUARDEDSTORAGE)
-#define CONFIG_SYS_IBAT6U (0xE0000000 |\
- BATU_BL_256M |\
- BATU_VS |\
- BATU_VP)
-#define CONFIG_SYS_DBAT6L CONFIG_SYS_IBAT6L
-#define CONFIG_SYS_DBAT6U CONFIG_SYS_IBAT6U
-
-#define CONFIG_SYS_IBAT7L (0)
-#define CONFIG_SYS_IBAT7U (0)
-#define CONFIG_SYS_DBAT7L CONFIG_SYS_IBAT7L
-#define CONFIG_SYS_DBAT7U CONFIG_SYS_IBAT7U
-
-/*
* U-Boot environment setup
*/
#define CONFIG_BOOTP_BOOTFILESIZE
*/
#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE
#define CONFIG_SYS_MONITOR_LEN (768 * 1024)
-#define CONFIG_SYS_MALLOC_LEN (8 * 1024 * 1024)
/*
* Environment Configuration
*/
-#define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE \
- + CONFIG_SYS_MONITOR_LEN)
-#define CONFIG_ENV_SIZE 0x20000
-#define CONFIG_ENV_ADDR_REDUND (CONFIG_ENV_ADDR + CONFIG_ENV_SIZE)
-#define CONFIG_ENV_SIZE_REDUND (CONFIG_ENV_SIZE)
#define CONFIG_NETDEV eth1
#define CONFIG_HOSTNAME "ids8313"
#define CONFIG_BOOTFILE "ids8313/uImage"
#define CONFIG_UBOOTPATH "ids8313/u-boot.bin"
#define CONFIG_FDTFILE "ids8313/ids8313.dtb"
-#define CONFIG_LOADADDR 0x400000
#define CONFIG_ENV_FLAGS_LIST_STATIC "ethaddr:mo,eth1addr:mo"
/* Initial Memory map for Linux*/
#define CONFIG_SYS_CBSIZE 1024
#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE
-#define CONFIG_SYS_MEMTEST_START 0x00001000
-#define CONFIG_SYS_MEMTEST_END 0x00C00000
-
-#define CONFIG_SYS_LOAD_ADDR 0x100000
-#define CONFIG_MII
#define CONFIG_LOADS_ECHO
#define CONFIG_TIMESTAMP
-#define CONFIG_PREBOOT "echo;" \
- "echo Type \\\"run nfsboot\\\" " \
- "to mount root filesystem over NFS;echo"
-#define CONFIG_BOOTCOMMAND "run boot_cramfs"
#undef CONFIG_SYS_LOADS_BAUD_CHANGE
#define CONFIG_JFFS2_NAND
#define CONFIG_JFFS2_DEV "0"
/* mtdparts command line support */
-#define CONFIG_FLASH_CFI_MTD
-#define CONFIG_MTD_DEVICE
#define CONFIG_EXTRA_ENV_SETTINGS \
"netdev=" __stringify(CONFIG_NETDEV) "\0" \
"mtdparts=" CONFIG_MTDPARTS_DEFAULT "\0" \
"\0"
-#define CONFIG_NFSBOOTCOMMAND \
- "setenv rootdev /dev/nfs;" \
- "run setipargs;run addmtd;" \
- "tftp ${loadaddr} ${bootfile};" \
- "tftp ${fdtaddr} ${fdtfile};" \
- "fdt addr ${fdtaddr};" \
- "bootm ${loadaddr} - ${fdtaddr}"
-
/* UBI Support */
-#define CONFIG_MTD_PARTITIONS
-
-#define CONFIG_IMAGE_FORMAT_LEGACY
#endif /* __CONFIG_H */
projects / platform / kernel / u-boot.git / blobdiff