* (C) Copyright 2008
* Daniel Hellstrom, Gaisler Research, daniel@gaisler.com.
*
- * See file CREDITS for list of people who contributed to this
- * project.
- *
- * This program is free software; you can redistribute it and/or
- * modify it under the terms of the GNU General Public License as
- * published by the Free Software Foundation; either version 2 of
- * the License, or (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
- * MA 02111-1307 USA
+ * SPDX-License-Identifier: GPL-2.0+
*/
#ifndef __CONFIG_H__
* (easy to change)
*/
-#define CONFIG_LEON3 /* This is an LEON3 CPU */
-#define CONFIG_LEON 1 /* This is an LEON CPU */
/* Altera NIOS Development board, Stratix II board */
#define CONFIG_GR_EP2S60 1
/* CPU / AMBA BUS configuration */
#define CONFIG_SYS_CLK_FREQ 96000000 /* 96MHz */
-/* Number of SPARC register windows */
-#define CONFIG_SYS_SPARC_NWINDOWS 8
-
/* Define this is the GR-2S60-MEZZ mezzanine is available and you
* want to use the USB and GRETH functionality of the board
*/
/*
* Supported commands
*/
-#include <config_cmd_default.h>
-
#define CONFIG_CMD_REGINFO
-#define CONFIG_CMD_AMBAPP
-#define CONFIG_CMD_PING
#define CONFIG_CMD_DIAG
#define CONFIG_CMD_IRQ
/* USB support */
#if USE_GRUSB
#define CONFIG_USB_UHCI
-#define CONFIG_CMD_FAT
-#define CONFIG_CMD_EXT2
-#define CONFIG_CMD_USB
-#define CONFIG_USB_STORAGE
/* Enable needed helper functions */
#define CONFIG_SYS_STDIO_DEREGISTER /* needs stdio_deregister */
#endif
/*
* Autobooting
*/
-#define CONFIG_BOOTDELAY 5 /* autoboot after 5 seconds */
#define CONFIG_PREBOOT "echo;" \
"echo Type \"run flash_nfs\" to mount root filesystem over NFS;" \
/* USE GRETH Ethernet Driver */
#define CONFIG_GRETH 1
-
-/* Default GRETH Ethernet HARDWARE address */
-#define GRETH_HWADDR_0 0x00
-#define GRETH_HWADDR_1 0x00
-#define GRETH_HWADDR_2 0x7a
-#define GRETH_HWADDR_3 0xcc
-#define GRETH_HWADDR_4 0x00
-#define GRETH_HWADDR_5 0x13
#endif
-#define CONFIG_ETHADDR 00:00:7a:cc:00:13
#define CONFIG_PHY_ADDR 0x00
/*
* Miscellaneous configurable options
*/
#define CONFIG_SYS_LONGHELP /* undef to save memory */
-#define CONFIG_SYS_PROMPT "=> " /* Monitor Command Prompt */
#if defined(CONFIG_CMD_KGDB)
#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */
#else
#define CONFIG_SYS_LOAD_ADDR 0x100000 /* default load address */
-#define CONFIG_SYS_HZ 1000 /* decrementer freq: 1 ms ticks */
-
/*-----------------------------------------------------------------------
* USB stuff
*-----------------------------------------------------------------------
/***** Gaisler GRLIB IP-Cores Config ********/
-/* AMBA Plug & Play info display on startup */
-/*#define CONFIG_SYS_AMBAPP_PRINT_ON_STARTUP*/
-
#define CONFIG_SYS_GRLIB_SDRAM 0
+/* No SDRAM Configuration */
+#undef CONFIG_SYS_GRLIB_GAISLER_SDCTRL1
+
/* See, GRLIB Docs (grip.pdf) on how to set up
* These the memory controller registers.
*/
-#define CONFIG_SYS_GRLIB_MEMCFG1 (0x10f800ff | (1<<11))
-#define CONFIG_SYS_GRLIB_MEMCFG2 0x00000000
-#define CONFIG_SYS_GRLIB_MEMCFG3 0x00000000
-
-#define CONFIG_SYS_GRLIB_FT_MEMCFG1 (0x10f800ff | (1<<11))
-#define CONFIG_SYS_GRLIB_FT_MEMCFG2 0x00000000
-#define CONFIG_SYS_GRLIB_FT_MEMCFG3 0x00000000
-
-#define CONFIG_SYS_GRLIB_DDR_CFG 0xa900830a
-
-#define CONFIG_SYS_GRLIB_DDR2_CFG1 0x00000000
-#define CONFIG_SYS_GRLIB_DDR2_CFG3 0x00000000
-
-/* Calculate scaler register value from default baudrate */
-#define CONFIG_SYS_GRLIB_APBUART_SCALER \
- ((((CONFIG_SYS_CLK_FREQ*10)/(CONFIG_BAUDRATE*8))-5)/10)
-
-/* Identification string */
-#define CONFIG_IDENT_STRING "GAISLER LEON3 EP2S60"
+#define CONFIG_SYS_GRLIB_ESA_MCTRL1
+#define CONFIG_SYS_GRLIB_ESA_MCTRL1_CFG1 (0x10f800ff | (1<<11))
+#define CONFIG_SYS_GRLIB_ESA_MCTRL1_CFG2 0x00000000
+#define CONFIG_SYS_GRLIB_ESA_MCTRL1_CFG3 0x00000000
+
+/* GRLIB FT-MCTRL configuration */
+#define CONFIG_SYS_GRLIB_GAISLER_FTMCTRL1
+#define CONFIG_SYS_GRLIB_GAISLER_FTMCTRL1_CFG1 (0x10f800ff | (1<<11))
+#define CONFIG_SYS_GRLIB_GAISLER_FTMCTRL1_CFG2 0x00000000
+#define CONFIG_SYS_GRLIB_GAISLER_FTMCTRL1_CFG3 0x00000000
+
+/* DDR controller */
+#define CONFIG_SYS_GRLIB_GAISLER_DDRSPA1
+#define CONFIG_SYS_GRLIB_GAISLER_DDRSPA1_CTRL 0xa900830a
+
+/* no DDR2 Controller */
+#undef CONFIG_SYS_GRLIB_GAISLER_DDR2SPA1
/* default kernel command line */
#define CONFIG_DEFAULT_KERNEL_COMMAND_LINE "console=ttyS0,38400\0\0"
projects / platform / kernel / u-boot.git / blobdiff