+++ /dev/null
-/*
- * (C) Copyright 2002 Scott McNutt <smcnutt@artesyncp.com>
- *
- * See file CREDITS for list of people who contributed to this
- * project.
- *
- * This program is free software; you can redistribute it and/or
- * modify it under the terms of the GNU General Public License as
- * published by the Free Software Foundation; either version 2 of
- * the License, or (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
- * MA 02111-1307 USA
- */
-
-/************************************************************************
- * board/config_EBONY.h - configuration for AMCC 440GP Ref (Ebony)
- ***********************************************************************/
-
-#ifndef __CONFIG_H
-#define __CONFIG_H
-
-/*-----------------------------------------------------------------------
- * High Level Configuration Options
- *----------------------------------------------------------------------*/
-#define CONFIG_EBONY 1 /* Board is ebony */
-#define CONFIG_440GP 1 /* Specifc GP support */
-#define CONFIG_440 1 /* ... PPC440 family */
-#define CONFIG_4xx 1 /* ... PPC4xx family */
-#define CONFIG_BOARD_EARLY_INIT_F 1 /* Call board_early_init_f */
-#undef CFG_DRAM_TEST /* Disable-takes long time! */
-#define CONFIG_SYS_CLK_FREQ 33333333 /* external freq to pll */
-
-/*
- * Define here the location of the environment variables (FLASH or NVRAM).
- * Note: DENX encourages to use redundant environment in FLASH. NVRAM is only
- * supported for backward compatibility.
- */
-#if 1
-#define CFG_ENV_IS_IN_FLASH 1 /* use FLASH for environment vars */
-#else
-#define CFG_ENV_IS_IN_NVRAM 1 /* use NVRAM for environment vars */
-#endif
-
-/*-----------------------------------------------------------------------
- * Base addresses -- Note these are effective addresses where the
- * actual resources get mapped (not physical addresses)
- *----------------------------------------------------------------------*/
-#define CFG_SDRAM_BASE 0x00000000 /* _must_ be 0 */
-#define CFG_FLASH_BASE 0xff800000 /* start of FLASH */
-#define CFG_MONITOR_BASE 0xfffc0000 /* start of monitor */
-#define CFG_PCI_MEMBASE 0x80000000 /* mapped pci memory */
-#define CFG_PERIPHERAL_BASE 0xe0000000 /* internal peripherals */
-#define CFG_ISRAM_BASE 0xc0000000 /* internal SRAM */
-#define CFG_PCI_BASE 0xd0000000 /* internal PCI regs */
-
-#define CFG_NVRAM_BASE_ADDR (CFG_PERIPHERAL_BASE + 0x08000000)
-#define CFG_FPGA_BASE (CFG_PERIPHERAL_BASE + 0x08300000)
-
-/*-----------------------------------------------------------------------
- * Initial RAM & stack pointer (placed in internal SRAM)
- *----------------------------------------------------------------------*/
-#define CFG_INIT_RAM_ADDR CFG_ISRAM_BASE /* Initial RAM address */
-#define CFG_INIT_RAM_END 0x2000 /* End of used area in RAM */
-#define CFG_GBL_DATA_SIZE 128 /* num bytes initial data */
-
-#define CFG_GBL_DATA_OFFSET (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE)
-#define CFG_INIT_SP_OFFSET CFG_GBL_DATA_OFFSET
-
-#define CFG_MONITOR_LEN (256 * 1024) /* Reserve 256 kB for Mon */
-#define CFG_MALLOC_LEN (128 * 1024) /* Reserve 128 kB for malloc*/
-
-/*-----------------------------------------------------------------------
- * Serial Port
- *----------------------------------------------------------------------*/
-#undef CONFIG_SERIAL_SOFTWARE_FIFO
-#define CFG_EXT_SERIAL_CLOCK (1843200 * 6) /* Ext clk @ 11.059 MHz */
-#define CONFIG_BAUDRATE 115200
-
-#define CFG_BAUDRATE_TABLE \
- {300, 600, 1200, 2400, 4800, 9600, 19200, 38400}
-
-/*-----------------------------------------------------------------------
- * NVRAM/RTC
- *
- * NOTE: Upper 8 bytes of NVRAM is where the RTC registers are located.
- * The DS1743 code assumes this condition (i.e. -- it assumes the base
- * address for the RTC registers is:
- *
- * CFG_NVRAM_BASE_ADDR + CFG_NVRAM_SIZE
- *
- *----------------------------------------------------------------------*/
-#define CFG_NVRAM_SIZE (0x2000 - 8) /* NVRAM size(8k)- RTC regs */
-#define CONFIG_RTC_DS174x 1 /* DS1743 RTC */
-
-#ifdef CFG_ENV_IS_IN_NVRAM
-#define CFG_ENV_SIZE 0x1000 /* Size of Environment vars */
-#define CFG_ENV_ADDR \
- (CFG_NVRAM_BASE_ADDR+CFG_NVRAM_SIZE-CFG_ENV_SIZE)
-#endif /* CFG_ENV_IS_IN_NVRAM */
-
-/*-----------------------------------------------------------------------
- * FLASH related
- *----------------------------------------------------------------------*/
-#define CFG_MAX_FLASH_BANKS 3 /* number of banks */
-#define CFG_MAX_FLASH_SECT 32 /* sectors per device */
-
-#define CFG_FLASH_ERASE_TOUT 120000 /* Timeout for Flash Erase (in ms) */
-#define CFG_FLASH_WRITE_TOUT 500 /* Timeout for Flash Write (in ms) */
-
-#define CFG_FLASH_EMPTY_INFO /* print 'E' for empty sector on flinfo */
-
-#define CFG_FLASH_ADDR0 0x5555
-#define CFG_FLASH_ADDR1 0x2aaa
-#define CFG_FLASH_WORD_SIZE unsigned char
-
-#ifdef CFG_ENV_IS_IN_FLASH
-#define CFG_ENV_SECT_SIZE 0x10000 /* size of one complete sector */
-#define CFG_ENV_ADDR (CFG_MONITOR_BASE-CFG_ENV_SECT_SIZE)
-#define CFG_ENV_SIZE 0x4000 /* Total Size of Environment Sector */
-
-/* Address and size of Redundant Environment Sector */
-#define CFG_ENV_ADDR_REDUND (CFG_ENV_ADDR-CFG_ENV_SECT_SIZE)
-#define CFG_ENV_SIZE_REDUND (CFG_ENV_SIZE)
-#endif /* CFG_ENV_IS_IN_FLASH */
-
-/*-----------------------------------------------------------------------
- * DDR SDRAM
- *----------------------------------------------------------------------*/
-#define CONFIG_SPD_EEPROM 1 /* Use SPD EEPROM for setup */
-#define SPD_EEPROM_ADDRESS {0x53,0x52} /* SPD i2c spd addresses */
-#define CONFIG_PROG_SDRAM_TLB 1 /* setup SDRAM TLB's dynamically*/
-
-/*-----------------------------------------------------------------------
- * I2C
- *----------------------------------------------------------------------*/
-#define CONFIG_HARD_I2C 1 /* I2C with hardware support */
-#undef CONFIG_SOFT_I2C /* I2C bit-banged */
-#define CFG_I2C_SPEED 400000 /* I2C speed and slave address */
-#define CFG_I2C_SLAVE 0x7F
-
-#define CFG_I2C_MULTI_EEPROMS
-#define CFG_I2C_EEPROM_ADDR (0xa8>>1)
-#define CFG_I2C_EEPROM_ADDR_LEN 1
-#define CFG_EEPROM_PAGE_WRITE_ENABLE
-#define CFG_EEPROM_PAGE_WRITE_BITS 3
-#define CFG_EEPROM_PAGE_WRITE_DELAY_MS 10
-
-#define CONFIG_PREBOOT "echo;" \
- "echo Type \"run flash_nfs\" to mount root filesystem over NFS;" \
- "echo"
-
-#undef CONFIG_BOOTARGS
-
-#define CONFIG_EXTRA_ENV_SETTINGS \
- "netdev=eth0\0" \
- "hostname=ebony\0" \
- "nfsargs=setenv bootargs root=/dev/nfs rw " \
- "nfsroot=${serverip}:${rootpath}\0" \
- "ramargs=setenv bootargs root=/dev/ram rw\0" \
- "addip=setenv bootargs ${bootargs} " \
- "ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}" \
- ":${hostname}:${netdev}:off panic=1\0" \
- "addtty=setenv bootargs ${bootargs} console=ttyS0,${baudrate}\0"\
- "flash_nfs=run nfsargs addip addtty;" \
- "bootm ${kernel_addr}\0" \
- "flash_self=run ramargs addip addtty;" \
- "bootm ${kernel_addr} ${ramdisk_addr}\0" \
- "net_nfs=tftp 200000 ${bootfile};run nfsargs addip addtty;" \
- "bootm\0" \
- "rootpath=/opt/eldk/ppc_4xx\0" \
- "bootfile=/tftpboot/ebony/uImage\0" \
- "kernel_addr=ff800000\0" \
- "ramdisk_addr=ff810000\0" \
- "initrd_high=30000000\0" \
- "load=tftp 100000 /tftpboot/ebony/u-boot.bin\0" \
- "update=protect off fffc0000 ffffffff;era fffc0000 ffffffff;" \
- "cp.b 100000 fffc0000 40000;" \
- "setenv filesize;saveenv\0" \
- "upd=run load;run update\0" \
- ""
-#define CONFIG_BOOTCOMMAND "run flash_self"
-
-#if 0
-#define CONFIG_BOOTDELAY -1 /* autoboot disabled */
-#else
-#define CONFIG_BOOTDELAY 5 /* autoboot after 5 seconds */
-#endif
-
-#define CONFIG_BAUDRATE 115200
-
-#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */
-#define CFG_LOADS_BAUD_CHANGE 1 /* allow baudrate change */
-
-#define CONFIG_MII 1 /* MII PHY management */
-#define CONFIG_PHY_ADDR 8 /* PHY address */
-#define CONFIG_HAS_ETH1
-#define CONFIG_PHY1_ADDR 9 /* EMAC1 PHY address */
-#define CONFIG_NET_MULTI 1
-#define CFG_RX_ETH_BUFFER 32 /* Number of ethernet rx buffers & descriptors */
-
-#define CONFIG_NETCONSOLE /* include NetConsole support */
-
-
-/*
- * BOOTP options
- */
-#define CONFIG_BOOTP_BOOTFILESIZE
-#define CONFIG_BOOTP_BOOTPATH
-#define CONFIG_BOOTP_GATEWAY
-#define CONFIG_BOOTP_HOSTNAME
-
-
-/*
- * Command line configuration.
- */
-#include <config_cmd_default.h>
-
-#define CONFIG_CMD_ASKENV
-#define CONFIG_CMD_DATE
-#define CONFIG_CMD_DHCP
-#define CONFIG_CMD_DIAG
-#define CONFIG_CMD_ELF
-#define CONFIG_CMD_EEPROM
-#define CONFIG_CMD_I2C
-#define CONFIG_CMD_IRQ
-#define CONFIG_CMD_MII
-#define CONFIG_CMD_NET
-#define CONFIG_CMD_NFS
-#define CONFIG_CMD_PCI
-#define CONFIG_CMD_PING
-#define CONFIG_CMD_REGINFO
-#define CONFIG_CMD_SDRAM
-#define CONFIG_CMD_SNTP
-
-
-#undef CONFIG_WATCHDOG /* watchdog disabled */
-
-/*
- * Miscellaneous configurable options
- */
-#define CFG_LONGHELP /* undef to save memory */
-#define CFG_PROMPT "=> " /* Monitor Command Prompt */
-#if defined(CONFIG_CMD_KGDB)
-#define CFG_CBSIZE 1024 /* Console I/O Buffer Size */
-#else
-#define CFG_CBSIZE 256 /* Console I/O Buffer Size */
-#endif
-#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */
-#define CFG_MAXARGS 16 /* max number of command args */
-#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */
-
-#define CFG_MEMTEST_START 0x0400000 /* memtest works on */
-#define CFG_MEMTEST_END 0x0C00000 /* 4 ... 12 MB in DRAM */
-
-#define CFG_LOAD_ADDR 0x100000 /* default load address */
-#define CFG_EXTBDINFO 1 /* To use extended board_into (bd_t) */
-
-#define CFG_HZ 1000 /* decrementer freq: 1 ms ticks */
-
-#define CONFIG_CMDLINE_EDITING 1 /* add command line history */
-#define CONFIG_LOOPW 1 /* enable loopw command */
-#define CONFIG_MX_CYCLIC 1 /* enable mdc/mwc commands */
-#define CONFIG_ZERO_BOOTDELAY_CHECK /* check for keypress on bootdelay==0 */
-#define CONFIG_VERSION_VARIABLE 1 /* include version env variable */
-
-/*-----------------------------------------------------------------------
- * PCI stuff
- *-----------------------------------------------------------------------
- */
-/* General PCI */
-#define CONFIG_PCI /* include pci support */
-#define CONFIG_PCI_PNP /* do pci plug-and-play */
-#define CONFIG_PCI_SCAN_SHOW /* show pci devices on startup */
-#define CFG_PCI_TARGBASE 0x80000000 /* PCIaddr mapped to CFG_PCI_MEMBASE */
-
-/* Board-specific PCI */
-#define CFG_PCI_TARGET_INIT /* let board init pci target */
-
-#define CFG_PCI_SUBSYS_VENDORID 0x10e8 /* AMCC */
-#define CFG_PCI_SUBSYS_DEVICEID 0xcafe /* Whatever */
-
-/*
- * For booting Linux, the board info and command line data
- * have to be in the first 8 MB of memory, since this is
- * the maximum mapped by the Linux kernel during initialization.
- */
-#define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */
-/*-----------------------------------------------------------------------
- * Cache Configuration
- */
-#define CFG_DCACHE_SIZE 8192 /* For AMCC 405 CPUs */
-#define CFG_CACHELINE_SIZE 32 /* ... */
-#if defined(CONFIG_CMD_KGDB)
-#define CFG_CACHELINE_SHIFT 5 /* log base 2 of the above value */
-#endif
-
-/*
- * Internal Definitions
- *
- * Boot Flags
- */
-#define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */
-#define BOOTFLAG_WARM 0x02 /* Software reboot */
-
-#if defined(CONFIG_CMD_KGDB)
-#define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */
-#define CONFIG_KGDB_SER_INDEX 2 /* which serial port to use */
-#endif
-#endif /* __CONFIG_H */
projects / platform / kernel / u-boot.git / blobdiff