+++ /dev/null
-/*
- * (C) Copyright 2003
- * Martin Winistoerfer, martinwinistoerfer@gmx.ch.
- *
- * SPDX-License-Identifier: GPL-2.0+
- */
-
-/*
- * File: cmi_mpc5xx.h
- *
- * Discription: Config header file for cmi
- * board using an MPC5xx CPU
- *
- */
-
-#ifndef __CONFIG_H
-#define __CONFIG_H
-
-/*
- * High Level Configuration Options
- */
-
-#define CONFIG_MPC555 1 /* This is an MPC555 CPU */
-#define CONFIG_CMI 1 /* Using the customized cmi board */
-
-#define CONFIG_SYS_TEXT_BASE 0x02000000 /* Boot from flash at location 0x00000000 */
-
-/* Serial Console Configuration */
-#define CONFIG_5xx_CONS_SCI1
-#undef CONFIG_5xx_CONS_SCI2
-
-#define CONFIG_BAUDRATE 57600
-
-
-/*
- * BOOTP options
- */
-#define CONFIG_BOOTP_BOOTFILESIZE
-#define CONFIG_BOOTP_BOOTPATH
-#define CONFIG_BOOTP_GATEWAY
-#define CONFIG_BOOTP_HOSTNAME
-
-
-/*
- * Command line configuration.
- */
-#include <config_cmd_default.h>
-
-#undef CONFIG_CMD_NFS
-
-#define CONFIG_CMD_MEMORY
-#define CONFIG_CMD_LOADB
-#define CONFIG_CMD_REGINFO
-#define CONFIG_CMD_FLASH
-#define CONFIG_CMD_LOADS
-#define CONFIG_CMD_ASKENV
-#define CONFIG_CMD_BDI
-#define CONFIG_CMD_CONSOLE
-#define CONFIG_CMD_SAVEENV
-#define CONFIG_CMD_RUN
-#define CONFIG_CMD_IMI
-
-
-#if 0
-#define CONFIG_BOOTDELAY -1 /* autoboot disabled */
-#else
-#define CONFIG_BOOTDELAY 5 /* autoboot after 5 seconds */
-#endif
-#define CONFIG_BOOTCOMMAND "go 02034004" /* autoboot command */
-
-#define CONFIG_BOOTARGS "" /* Assuming OS Image in 4 flash sector at offset 4004 */
-
-#define CONFIG_WATCHDOG /* turn on platform specific watchdog */
-
-#define CONFIG_STATUS_LED 1 /* Enable status led */
-
-#define CONFIG_LOADS_ECHO 1 /* Echo on for serial download */
-
-/*
- * Miscellaneous configurable options
- */
-
-#define CONFIG_SYS_LONGHELP /* undef to save memory */
-#if defined(CONFIG_CMD_KGDB)
-#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */
-#else
-#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */
-#endif
-#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */
-#define CONFIG_SYS_MAXARGS 16 /* max number of command args */
-#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */
-
-#define CONFIG_SYS_MEMTEST_START 0x00000000 /* memtest works on */
-#define CONFIG_SYS_MEMTEST_END 0x000fa000 /* 1 MB in SRAM */
-
-#define CONFIG_SYS_LOAD_ADDR 0x100000 /* default load address */
-
-#define CONFIG_SYS_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200, 1250000 }
-
-
-/*
- * Low Level Configuration Settings
- */
-
-/*
- * Internal Memory Mapped (This is not the IMMR content)
- */
-#define CONFIG_SYS_IMMR 0x01000000 /* Physical start adress of internal memory map */
-
-/*
- * Definitions for initial stack pointer and data area
- */
-#define CONFIG_SYS_INIT_RAM_ADDR (CONFIG_SYS_IMMR + 0x003f9800) /* Physical start adress of internal MPC555 writable RAM */
-#define CONFIG_SYS_INIT_RAM_SIZE (CONFIG_SYS_IMMR + 0x003fffff) /* Physical end adress of internal MPC555 used RAM area */
-#define CONFIG_SYS_GBL_DATA_OFFSET ((CONFIG_SYS_INIT_RAM_SIZE - CONFIG_SYS_INIT_RAM_ADDR) - GENERATED_GBL_DATA_SIZE) /* Offset from the beginning of ram */
-#define CONFIG_SYS_INIT_SP_ADDR 0x013fa000 /* Physical start adress of inital stack */
-
-/*
- * Start addresses for the final memory configuration
- * Please note that CONFIG_SYS_SDRAM_BASE _must_ start at 0
- */
-#define CONFIG_SYS_SDRAM_BASE 0x00000000 /* Monitor won't change memory map */
-#define CONFIG_SYS_FLASH_BASE 0x02000000 /* External flash */
-#define PLD_BASE 0x03000000 /* PLD */
-#define ANYBUS_BASE 0x03010000 /* Anybus Module */
-
-#define CONFIG_SYS_RESET_ADRESS 0x01000000 /* Adress which causes reset */
-#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_FLASH_BASE /* CONFIG_SYS_TEXT_BASE is defined in the board config.mk file. */
- /* This adress is given to the linker with -Ttext to */
- /* locate the text section at this adress. */
-#define CONFIG_SYS_MONITOR_LEN (192 << 10) /* Reserve 192 kB for Monitor */
-#define CONFIG_SYS_MALLOC_LEN (64 << 10) /* Reserve 128 kB for malloc() */
-
-/*
- * For booting Linux, the board info and command line data
- * have to be in the first 8 MB of memory, since this is
- * the maximum mapped by the Linux kernel during initialization.
- */
-#define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */
-
-
-/*-----------------------------------------------------------------------
- * FLASH organization
- *-----------------------------------------------------------------------
- *
- */
-
-#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* Max number of memory banks */
-#define CONFIG_SYS_MAX_FLASH_SECT 64 /* Max number of sectors on one chip */
-#define CONFIG_SYS_FLASH_ERASE_TOUT 180000 /* Timeout for Flash Erase (in ms) */
-#define CONFIG_SYS_FLASH_WRITE_TOUT 600 /* Timeout for Flash Write (in ms) */
-#define CONFIG_SYS_FLASH_PROTECTION 1 /* Physically section protection on */
-
-#define CONFIG_ENV_IS_IN_FLASH 1
-
-#ifdef CONFIG_ENV_IS_IN_FLASH
-#define CONFIG_ENV_OFFSET 0x00020000 /* Environment starts at this adress */
-#define CONFIG_ENV_SIZE 0x00010000 /* Set whole sector as env */
-#define CONFIG_SYS_USE_PPCENV /* Environment embedded in sect .ppcenv */
-#endif
-
-/*-----------------------------------------------------------------------
- * SYPCR - System Protection Control
- * SYPCR can only be written once after reset!
- *-----------------------------------------------------------------------
- * SW Watchdog freeze
- */
-#if defined(CONFIG_WATCHDOG)
-#define CONFIG_SYS_SYPCR (SYPCR_SWTC | SYPCR_BMT | SYPCR_BME | SYPCR_SWF | \
- SYPCR_SWE | SYPCR_SWRI| SYPCR_SWP)
-#else
-#define CONFIG_SYS_SYPCR (SYPCR_SWTC | SYPCR_BMT | SYPCR_BME | SYPCR_SWF | \
- SYPCR_SWP)
-#endif /* CONFIG_WATCHDOG */
-
-/*-----------------------------------------------------------------------
- * TBSCR - Time Base Status and Control
- *-----------------------------------------------------------------------
- * Clear Reference Interrupt Status, Timebase freezing enabled
- */
-#define CONFIG_SYS_TBSCR (TBSCR_REFA | TBSCR_REFB | TBSCR_TBF)
-
-/*-----------------------------------------------------------------------
- * PISCR - Periodic Interrupt Status and Control
- *-----------------------------------------------------------------------
- * Clear Periodic Interrupt Status, Interrupt Timer freezing enabled
- */
-#define CONFIG_SYS_PISCR (PISCR_PITF)
-
-/*-----------------------------------------------------------------------
- * SCCR - System Clock and reset Control Register
- *-----------------------------------------------------------------------
- * Set clock output, timebase and RTC source and divider,
- * power management and some other internal clocks
- */
-#define SCCR_MASK SCCR_EBDF00
-#define CONFIG_SYS_SCCR (SCCR_TBS | SCCR_RTDIV | SCCR_RTSEL | \
- SCCR_COM00 | SCCR_DFNL000 | SCCR_DFNH000)
-
-/*-----------------------------------------------------------------------
- * SIUMCR - SIU Module Configuration
- *-----------------------------------------------------------------------
- * Data show cycle
- */
-#define CONFIG_SYS_SIUMCR (SIUMCR_DBGC00) /* Disable data show cycle */
-
-/*-----------------------------------------------------------------------
- * PLPRCR - PLL, Low-Power, and Reset Control Register
- *-----------------------------------------------------------------------
- * Set all bits to 40 Mhz
- *
- */
-#define CONFIG_SYS_OSC_CLK ((uint)4000000) /* Oscillator clock is 4MHz */
-#define CONFIG_SYS_PLPRCR (PLPRCR_MF_9 | PLPRCR_DIVF_0)
-
-
-/*-----------------------------------------------------------------------
- * UMCR - UIMB Module Configuration Register
- *-----------------------------------------------------------------------
- *
- */
-#define CONFIG_SYS_UMCR (UMCR_FSPEED) /* IMB clock same as U-bus */
-
-/*-----------------------------------------------------------------------
- * ICTRL - I-Bus Support Control Register
- */
-#define CONFIG_SYS_ICTRL (ICTRL_ISCT_SER_7) /* Take out of serialized mode */
-
-/*-----------------------------------------------------------------------
- * USIU - Memory Controller Register
- *-----------------------------------------------------------------------
- */
-
-#define CONFIG_SYS_BR0_PRELIM (CONFIG_SYS_FLASH_BASE | BR_V | BR_BI | BR_PS_16)
-#define CONFIG_SYS_OR0_PRELIM (OR_ADDR_MK_FF | OR_SCY_3)
-#define CONFIG_SYS_BR1_PRELIM (ANYBUS_BASE)
-#define CONFIG_SYS_OR1_PRELIM (OR_ADDR_MK_FFFF | OR_SCY_1 | OR_ETHR)
-#define CONFIG_SYS_BR2_PRELIM (CONFIG_SYS_SDRAM_BASE | BR_V | BR_PS_32)
-#define CONFIG_SYS_OR2_PRELIM (OR_ADDR_MK_FF)
-#define CONFIG_SYS_BR3_PRELIM (PLD_BASE | BR_V | BR_BI | BR_LBDIR | BR_PS_8)
-#define CONFIG_SYS_OR3_PRELIM (OR_ADDR_MK_FF | OR_TRLX | OR_BSCY | OR_SCY_8 | \
- OR_ACS_10 | OR_ETHR | OR_CSNT)
-
-#define FLASH_BASE0_PRELIM CONFIG_SYS_FLASH_BASE /* We don't realign the flash */
-
-/*-----------------------------------------------------------------------
- * DER - Timer Decrementer
- *-----------------------------------------------------------------------
- * Initialise to zero
- */
-#define CONFIG_SYS_DER 0x00000000
-
-#endif /* __CONFIG_H */
projects / platform / kernel / u-boot.git / blobdiff